RESUMEN
Titanium nitride (TiN) is a complementary metal-oxide-semiconductor (CMOS) compatible material with large potential for the fabrication of plasmonic structures suited for device integration. However, the comparatively large optical losses can be detrimental for application. This work reports a CMOS compatible TiN nanohole array (NHA) on top of a multilayer stack for potential use in integrated refractive index sensing with high sensitivities at wavelengths between 800 and 1500â nm. The stack, consisting of the TiN NHA on a silicon dioxide (SiO2) layer with Si as substrate (TiN NHA/SiO2/Si), is prepared using an industrial CMOS compatible process. The TiN NHA/SiO2/Si shows Fano resonances in reflectance spectra under oblique excitation, which are well reproduced by simulation using both finite difference time domain (FDTD) and rigorous coupled-wave analysis (RCWA) methods. The sensitivities derived from spectroscopic characterizations increase with the increasing incident angle and match well with the simulated sensitivities. Our systematic simulation-based investigation of the sensitivity of the TiN NHA/SiO2/Si stack under varied conditions reveals that very large sensitivities up to 2305â nm per refractive index unit (nm RIU-1) are predicted when the refractive index of superstrate is similar to that of the SiO2 layer. We analyze in detail how the interplay between plasmonic and photonic resonances such as surface plasmon polaritons (SPPs), localized surface plasmon resonances (LSPRs), Rayleigh Anomalies (RAs), and photonic microcavity modes (Fabry-Pérot resonances) contributes to this result. This work not only reveals the tunability of TiN nanostructures for plasmonic applications but also paves the way to explore efficient devices for sensing in broad conditions.
RESUMEN
We apply the rigorous coupled-wave analysis (RCWA) to the design of a multi-layer plasmonic refractive index sensor based on metallic nanohole arrays integrated with a Ge-on-Si photodetector. RCWA simulations benefit from modularity, frequency-domain computation, and a relatively simple computational setup. These features make the application of RCWA particularly interesting in the case of the simulation and optimization of multi-layered devices in conjunction with plasmonic nanostructures, where other methods can be computationally too expensive for multi-parameter optimization. Our application example serves as a demonstration that RCWA can be utilized as a low-cost, efficient method for device engineering.
RESUMEN
We report on the fabrication and electro-optical characterization of SiGeSn multi-quantum well PIN diodes. Two types of PIN diodes, in which two and four quantum wells with well and barrier thicknesses of 10 nm each are sandwiched between B- and Sb-doped Ge-regions, were fabricated as single-mesa devices, using a low-temperature fabrication process. We discuss measurements of the diode characteristics, optical responsivity and room-temperature electroluminescence and compare with theoretical predictions from band structure calculations.
RESUMEN
Multi-quantum well light-emitting diodes, consisting of ten alternating GeSn/Ge-layers, were grown by molecular beam epitaxy on Si. The Ge barriers were 10 nm thick, and the GeSn wells were grown with 7% Sn and thicknesses between 6 and 12 nm. The electroluminescence spectra measured at 300 and 80 K yield a broad and intensive luminescence band. Deconvolution revealed three major lines produced by the GeSn wells that can be interpreted in terms of quantum confinement. We interpret that the three lines represent two direct lines, formed by transitions with the light and heavy hole band, respectively, and an indirect line. Biaxial compressive strain causes a splitting of light and heavy holes in the GeSn wells. This interpretation is supported by an effective mass band structure calculation.
RESUMEN
Incorporating group IV photonic nanostructures within active top-illuminated photonic devices often requires light-transmissive contact schemes. In this context, plasmonic nanoapertures in metallic films can not only be realized using CMOS compatible metals and processes, they can also serve to influence the wavelength-dependent device responsivities. Here, we investigate crescent-shaped nanoapertures in close proximity to Ge-on-Si PIN nanopillar photodetectors both in simulation and experiment. In our geometries, the absorption within the devices is mainly shaped by the absorption characteristics of the vertical semiconductor nanopillar structures (leaky waveguide modes). The plasmonic resonances can be used to influence how incident light couples into the leaky modes within the nanopillars. Our results can serve as a starting point to selectively tune our device geometries for applications in spectroscopy or refractive index sensing.
RESUMEN
Low-temperature magnetoresistance measurements of n- and p-doped germanium-tin (Ge1-y Sn y ) layers with Sn concentrations up to 8% show contributions arising from effects of weak localization for n-type and weak antilocalization for p-type doped samples independent of the Sn concentration. Calculations of the magnetoresistance using the Hikami-Larkin-Nagaoka model for two-dimensional transport allow us to extract the phase-coherence length for all samples as well as the spin-orbit length for the p-type doped samples. For pure Ge, we find phase-coherence lengths as long as (349.0 ± 1.4) nm and (614.0 ± 0.9) nm for n-type and p-type doped samples, respectively. The phase-coherence length decreases with increasing Sn concentration. From the spin-orbit scattering length, we determine the spin-diffusion scattering length in the range of 20-30 nm for all highly degenerate p-type doped samples irrespective of Sn concentration. These results show that Ge1-y Sn y is a promising material for future spintronic applications.