Evaluation of barrier materials for removing pollutants from groundwater rich in natural organic matter.

Permeable barriers are used for passive remediation of groundwater and can be constructed from a range of materials. The optimal material depends on the types of contaminants and physico-chemical parameters present at the site, as well as the hydraulic conductivity, environmental safety, availability, cost and long-term stability of the material itself. The aim of the presented study was to test a number of materials for their ability to remove heavy metals and organic pollutants from groundwater with a high (140 mg L(-1)) content of natural organic matter (NOM). The following materials were included in the study: sand, peat, fly ash, iron powder, lignin and combinations thereof. Polluted water was fed into glass columns loaded with each sorbent and the contaminant removal efficiency of the material was evaluated through chemical analysis of the percolate. Materials based on fly ash and zero-valent iron were found to be the most effective for heavy metal removal, while fly ash and peat were the most effective for removing aliphatic compounds. Filtration through lignin and peat led to leaching of NOM. Although the leaching decreased over time, it remained high throughout the experiments. The results indicate that remediation of contaminated land at disused industrial sites is a complex task that often requires the use of mixed materials or a minimum of two sequential barriers.

Behavior and fate of anthropogenic substances at a Swedish sewage treatment plant.

The behavior and fate of anthropogenic substances during sewage treatment were investigated at a sewage treatment plant (STP) in Sweden which uses mechanical, chemical, and biological methods for sewage treatment and anaerobic digestion of sludge. Influent and effluent water, and sludge from two specific treatment sites were sampled. Mass balances were calculated from measured concentrations of various substances and estimates of the mass flows (water, solids) throughout the process. The results show that the metals (As, Cd, Cr, Hg, Pb) and the majority of PCBs, PCDD/Fs, and PBDEs enter and leave the STP bound to particles. Triclosan and di-(2-ethylhexyl)phthalate adsorb to sludge to a high degree, while the metals (Co, Cu, Ni, Zn) and organophosphate esters seem to pass through the STP unaffected by the process. Generally, the STP was better in removing lipophilic than water soluble compounds. Most of the substances end up in anaerobically digested sludge in almost the same concentrations as in primary sludge. A fugacity based STP model was evaluated for its ability to predict the behavior and fate of the substances and was found feasible for lipophilic compounds. It did however produce poor predictions for water soluble compounds such as organophosphate esters (overestimated) and antibacterial agents (underestimated).

Sorbent-assisted liquid-liquid extraction (Chem-Elut) of polychlorinated biphenyls, dibenzo-p-dioxins and dibenzofurans in the lipid fraction of human blood plasma.

This work compares two lipid extraction methods for determining 24 polychlorinated biphenyls (PCBs), seven dibenzo-p-dioxins (PCDDs) and ten dibenzofurans (PCDFs) in human blood plasma. The first method was based on conventional liquid-liquid partitioning with chloroform-methanol and the other made use of a sorbent (Chem-Elut) to facilitate the partitioning of lipids into a mixture of hexane and 2-propanol. A multi-layer-silica column including acid- and base-impregnated silica gel was used to reduce the amounts of lipid present in the samples before a basic alumina clean-up step and activated carbon fractionation of planar analytes (PCDD/Fs and non-ortho-PCBs) and non-planar analytes (including ortho-chlorinated PCBs). Gas chromatography coupled to high resolution mass spectrometry was used to identify and quantify the analytes in the two fractions. The wet weight based concentrations obtained by the two methods were in agreement but both methods suffer from large organic solvent consumption. The toxic equivalencies derived for PCBs and PCDD/Fs using the two methods were also in agreement. However, the chloroform-methanol method gave slightly higher lipid recoveries, although with greater variation, than the sorbent-assisted method. Nevertheless, despite giving lower lipid recoveries, the sorbent-assisted method has advantages in ease of use and applicability to whole blood samples. The formation of emulsions was avoided with the Chem-Elut method, which probably explains the lower variability in the lipid determinations.

Effects of predicted climatic changes on distribution of organic contaminants in brackish water mesocosms.

Predicted consequences of future climate change in the northern Baltic Sea include increases in sea surface temperatures and terrestrial dissolved organic carbon (DOC) runoff. These changes are expected to alter environmental distribution of anthropogenic organic contaminants (OCs). To assess likely shifts in their distributions, outdoor mesocosms were employed to mimic pelagic ecosystems at two temperatures and two DOC concentrations, current: 15°C and 4 mg DOCL(-1) and, within ranges of predicted increases, 18°C and 6 mg DOCL(-1), respectively. Selected organic contaminants were added to the mesocosms to monitor changes in their distribution induced by the treatments. OC partitioning to particulate matter and sedimentation were enhanced at the higher DOC concentration, at both temperatures, while higher losses and lower partitioning of OCs to DOC were observed at the higher temperature. No combined effects of higher temperature and DOC on partitioning were observed, possibly because of the balancing nature of these processes. Therefore, changes in OCs' fates may largely depend on whether they are most sensitive to temperature or DOC concentration rises. Bromoanilines, phenanthrene, biphenyl and naphthalene were sensitive to the rise in DOC concentration, whereas organophosphates, chlorobenzenes (PCBz) and polychlorinated biphenyls (PCBs) were more sensitive to temperature. Mitotane and diflufenican were sensitive to both temperature and DOC concentration rises individually, but not in combination.

Pressurised liquid extraction of polycyclic aromatic hydrocarbons from contaminated soils.

The reliability and efficiency of the pressurised liquid extraction technique (PLE) for extracting polycyclic aromatic hydrocarbons (PAHs) from contaminated soil has been investigated. Experimental design was used to study the influence of seven extraction variables (sample load, solvents used, solvent ratios, pressure, temperature, extraction time, and rinse volume). The results show that large sample loads in combination with small solvent volumes may result in low extraction efficiency. They also indicate that the recovery of low-molecular-mass PAHs is reduced by low extraction temperatures. The exact settings of the other variables are, however, less significant for the extraction efficiency. Repeated extractions at optimised settings of the tested variables show that PLE is an exhaustive extraction technique that generally results in high yields. In addition, extraction of a certified reference material (CRM 103-100) revealed that the method is both accurate and precise. Another finding was that adding the internal standard on top of the soil in the extraction cell causes considerable over-estimation of the concentrations when large samples are extracted with small solvent volumes. This is because the PLE-cell resembles a chromatographic column, so compounds added to the top of the soil layer have a longer distance to travel through the soil compared to the average distance of the native compounds, which are distributed evenly throughout the column. We therefore recommend that the internal standard should be added to the extract immediately after the extraction or, alternatively, carefully mixed with the sample prior to extraction.

Separation of seventeen 2,3,7,8-substituted polychlorinated dibenzo-p-dioxins and dibenzofurans and 12 dioxin-like polychlorinated biphenyls by comprehensive two-dimensional gas chromatography with electron-capture detection.

Comprehensive two-dimensional gas chromatography (GC x GC) with electron-capture detection (ECD) has been optimized for the separation of seventeen 2,3,7,8-substituted polychlorinated dibenzo-p-dioxins and dibenzofurans and 12 dioxin-like polychlorinated biphenyls, with emphasis on the selection of the first- and second-dimension, commercially available, columns. When eight second-dimension columns were subsequently combined with a 100% methylpolysiloxane stationary phase (DB-1) in the first dimension to create orthogonal conditions, a complete separation of all congeners with different TEF values was obtained with two column combinations, DB-1 x VF-23 and DB-1 x LC-50. When other types of first-dimension columns were used (and orthogonality was partly sacrificed), a DB-XLB column combined with 007-65HT, VF-23 and LC-50 was found to provide a complete separation of all 29 priority congeners. Next, the potential of these three column combinations for real-life analysis was preliminarily studied. With a spiked and fractionated milk extract, DB-XLB x LC-50 was found to be the most powerful column combination, because of the good separation of the 29 priority congeners from each other as well as from the matrix constituents. Quantitative performance (close to three-order linearity; LODs, 30-150 fg injected; R.S.D.s, 1.5-6.5% (n = 10)) was satisfactory.

Search for chlorobornanes in river sediments and in influents and effluents.

In 1997, we collected nine river sediment samples, including one duplicate, from above and below three pulp and paper mills on the Wisconsin River in Wisconsin, USA, and one mill on Beaver Dam Creek in Ontario, Canada. We also obtained twenty split sediment samples from the Wisconsin River that were collected by the US EPA in collaboration with Indiana University. Finally, we collected influent and effluent samples from eight pulp and paper related industries in the US and Canada. We analyzed all sediment and water samples for hexa- through decachlorobornanes. We did not detect any chlorobornanes in most of the sediments. When chlorobornanes were detected, the concentration in sediments below pulp mills were similar to or less than in those from above the same mills. Chlorobornanes could not be detected in any of the influent or effluent samples. Thus, pulp and paper mills and relate facilities are not a source of chlorobornanes.

Discrimination and thermal degradation of toxaphene compounds in capillary gas chromatography when using split/splitless and on-column injection.

Technical toxaphene and a 22-component Reference Mixture were analyzed using capillary gas chromatography with split/splitless injection (SSL) and on-column injection (OC). In both techniques, electron-capture, negative ionization mass spectrometry (ECNI-MS) was used for detection of chlorobornanes, chlorocamphenes and related compounds. Significant discrimination of highly chlorinated congeners was observed as a result of incomplete transfer of these compounds from the vaporizer to the analytical column when using SSL. This resulted in a much lower response for nona- and decachloro congeners than when using OC. In addition, several toxaphene components, especially the chlorobornanes with gem dichloro substitution on the six-member carbon ring, undergo thermal degradation when using SSL. Some of these congeners are major components of technical toxaphene, but generally are not present, except at low concentrations, in environmental and biological samples. Therefore, technical toxaphene may be discriminated and/or degraded differently than toxaphene compounds in environmental samples when using SSL. This results in significant bias of the quantitative data when using the technical material as a reference. OC suffers much less from these deficiencies and, therefore, is a preferable technique for toxaphene analysis.

Rapid anaerobic degradation of toxaphene in sewage sludge.

We studied the degradation of technical toxaphene in anaerobic sewage sludge from a municipal waste water treatment plant. Chlorobornanes, chlorocamphenes and related compounds were rapidly degraded, with degradation rates in the order of decachloro>nonachloro>octochloro>heptachloro approximately = hexachloro compounds. The half-lives of individual congeners ranged from <1 day to several days. We also studied the degradation of technical toxaphene in previously sterilized sludge (control), and found it was slower than in the anaerobic sludge. The chlorobornanes that degraded most rapidly in the non-sterilized anaerobic sludge were those with gem chloro substitution on the 6-member carbon-ring, including the toxic congeners, Toxicant A and B. Non-gem chloro substituted congeners, like the biologically persistent P26 and P50, also degraded, but less rapidly. Toxaphene degradation in sewage sludge proceeded primarily via reductive dechlorination, leading to HxSed, HpSed, TC2 and other persistent metabolites. Enantioselective determinations indicated little, if any, enantioselectivity in the formation and/or degradation of these compounds. The isomer and enantiomer profiles of the hexa-, hepta-, and octachlorobornanes are similar to those observed in sediment from the Baltic Sea, suggesting that technical toxaphene is the source of these compounds and that its composition was changed via similar anaerobic degradation pathways.

Fatal intoxications with chloral hydrate.

An alcoholic man, treated with chloral hydrate (CH) syrup to which he was dependent, was discovered comatose and in respiratory arrest. Death occurred on the ninth day of hospitalization following cerebral oedema. A woman, alcohol addicted, depressed, and epileptic was admitted in the Intensive Care Unit with heart and respiratory failure following CH absorption. She died three days later after a deep coma. In these two cases, CH intoxication was confirmed by toxicological analysis: CH and its major metabolite, trichloroethanol (TCE), were identified and determined in serum and urine using headspace-capillary gas chromatography-mass spectrometry. The concentrations measured were compared with those found in previously published fatalities. The analytical method used can be proposed for both clinical and forensic cases.

Selection of Polychlorinated Biphenyls for use in Quantitative Structure-Activity Modelling.

Abstract By characterizing the 154 tetra- through heptachlorinated biphenyl (PCB) congeners with a multitude of physico-chemical descriptors, a model representing chemical similarities and differences is achieved. The multivariate characterization of the PCBs was based on 47 physico-chemical descriptor variables, which were summarised by using principal component analysis (PCA). By applying statistical design to the orthogonal scores from the PCA, a 2(4)-factorial design was used to select a set of 16 congeners. In addition, four congeners were added to provide information about the interior region of the chemical domain of PCBs. This set of 20 structurally different congeners is suggested to be used in future quantitative structure-activity relationships (QSARs) for screening of the toxicological and biochemical effects of the PCBs.

The internal barriers of rotation for the 209 polychlorinated biphenyls.

The internal barrier of rotation (Erot) was calculated for all 209 polychlorinated biphenyls (PCBs) by using a semi-empirical method, viz. the Austin Model 1 (AMI) Hamiltonian. The difference in total energy between a forced planar state and an optimised twisted structure was defined as Erot. The Erot values were in the range of 8.33 to 483 kJ/mol, and were significantly influenced by the number of chlorine atoms in ortho position. An additional structural characteristic of the PCBs influencing Erot of ortho substituted congeners was substitution by chlorine atoms in vicinal meta positions, which is assumed to prevent outward bending of ortho substituents. This so-called buttressing effect contributed with 4 to 31 kJ/mol per added chlorine atom. In conclusion, the internal barrier of rotation, calculated for all 209 PCBs, provides an important structure dependent physico-chemical parameter for multivariate modelling of future quantitative structure-activity and structure-property relationships (QSARs/QSPRs).

Coastal sediments in the Gulf of Bothnia as a source of dissolved PCDD/Fs and PCBs to water and fish.

High levels of PCDD/Fs and PCBs in Baltic Sea biota have been a matter of great concern during the last decades. We measured the freely dissolved concentrations of PCDD/Fs and PCBs in sediment pore water and bottom water in eight areas along the Swedish coast of the Gulf of Bothnia, by using state-of-the-art passive samplers. Chemical activity ratios (calculated from freely dissolved concentrations in pore water and bottom water based on chemical activity ratios) for PCDD/Fs were higher than 1 at all stations (PCDD/Fs average 27; stdev 22). High activity ratios suggest that the sediments have a potential to act as a source of dissolved PCDD/Fs to the water column. Activity ratios for PCBs varied between 0.3 and 17 (average 2; stdev 4). The concentrations of PCDD/Fs and PCBs in bottom water were significantly correlated with concentrations in sediment pore water (p<0.00001 to p=0.03) as well as with concentrations in juvenile perch caught in the same areas (p<0.00001 to p=0.02). To our knowledge, this is the first study demonstrating a correlation between in-situ measured freely dissolved PCDD/F concentrations and lipid-normalized contents in stationary fish. Our results confirm that freely dissolved concentrations should be used as chemical predictors of bioaccumulation. The results from this study imply that continued efforts to reduce levels of PCDD/Fs and PCBs in coastal sediments will have positive effects on concentrations of these contaminants in lower trophic levels of Baltic Sea ecosystems.

Retention and maternal transfer of brominated dioxins in zebrafish (Danio rerio) and effects on reproduction, aryl hydrocarbon receptor-regulated genes, and ethoxyresorufin-O-deethylase (EROD) activity.

Brominated dioxins have recently been detected in Baltic Sea biota. Due to their similarities to the highly toxic chlorinated dioxins, concern has been raised about their potential biological effects. The present study investigated retention and effects of brominated dioxins in adult zebrafish, as well as maternal transfer and effects on offspring. We exposed adult zebrafish for nine weeks via feed to 2,3,7,8-tetrabromodibenzo-p-dioxin (TBDD) or to a mixture of brominated dioxins (Baltic Sea mixture), which was designed to reflect relative concentrations found in Baltic Sea biota. We studied spawning success, gonad morphology, hepatic vitellogenin gene expression, and offspring early life-stage development to investigate effects on zebrafish reproduction. Hepatic ethoxyresorufin-O-deethylase (EROD) activity and hepatic expression of a number of aryl hydrocarbon receptor (AHR)-regulated genes were studied to investigate if the brominated dioxins can activate gene transcription through the AHR pathway in zebrafish. In addition, glutathione reductase activity and expression of genes involved in adaptive responses to intracellular stress were studied to investigate potential stress effects of brominated dioxins. After nine weeks of exposure, all brominated dioxins spiked to the feed were detected in female fish and transferred to eggs. Exposure to the Baltic Sea mixture and TBDD clearly induced AHR-regulated genes and EROD activity. Exposure to TBDD reduced spawning success, altered ovarian morphology and reduced hepatic vitellogenin gene expression, which implies that TBDD has a similar effect pattern as the chlorinated analogue. Overall, our results show that dietary exposure to sublethal concentrations of brominated dioxins may impair reproductive physiology in fish and induce AHR-regulated genes.

Shape-selective extraction of PCBs and dioxins from fish and fish oil using in-cell carbon fractionation pressurized liquid extraction.

This paper describes a new shape-selective, pressurized liquid extraction (PLE) procedure for extracting polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and PCBs from food and feed samples with an integrated carbon fractionation step. Initially this was done using specially designed inserts for 34-mL cells, but subsequently, large solid cells (66 mL) were machined to increase the capacity and robustness of the system. Depending on the carbon load and extraction solvent strength, the non-ortho PCBs were recovered either with the bulk of the PCBs or with the PCDD/Fs. The former is preferable if PCDD/Fs are the targets. In most cases, however, data are required for all indicator PCBs, WHO-PCBs, and PCDD/Fs. Therefore, further efforts focused on developing, optimizing, and validating a cost- and time-efficient PLE procedure that can extract these targets, separate non-ortho PCBs and PCDD/Fs from the bulk of the PCBs, allow gravimetric fat determinations, and requires a minimum of postextraction cleanup. The performance of the resulting procedure was assessed in experiments with a fish tissue reference material. The trueness of the WHO-PCB-TEQ, PCDD/F-TEQ, and total-TEQ data were -8, -5, and -7%, respectively, and the corresponding CVs were 1.5, 0.5, and 1.3%; within the limits set by the European community for gas chromatography-high-resolution mass spectrometry methods for food and feed control.

Identification of markers for PCB exposure in plasma from Swedish construction workers removing old elastic sealants.

The objective of the present study was to identify PCB-indicators of occupational exposure related to the removal of old elastic sealants. Blood samples were collected from workers involved in removing elastic sealants. Samples were also taken from age- and sex-matched controls. A majority of the exposed workers were re-sampled after 10 months. All samples were analysed for 19 PCBs. The levels in the exposed workers were twice as high as those in the controls, 575 and 267 ng g(-1) lipid, respectively, but were essentially unchanged at the second sampling. The PCB patterns also differed. Levels of many less chlorinated PCBs were much higher in the exposed workers, compared to the controls, and principal component analysis (PCA) revealed that easily metabolized PCBs decreased in the exposed workers during the study. This finding indicates that elimination exceeded uptake during the study period, and that the safety information given to the workers had been effective. PCA was also used to identify exposure markers. The relatively persistent PCBs 56/60 and 66, the easily metabolized PCBs 44, 70 and 110 (with vicinal hydrogens in meta/para-positions) and the very persistent PCBs 153 and 180 were found to be good markers for occupational, recent occupational and background (dietary) exposure, respectively. A PCA model based on these markers was equally effective in differentiating between exposed individuals and controls, and between recent and less recent exposure, as a model based on all PCBs.

Isolation of toxic polychlorinated biphenyls by electron donor-acceptor high-performance liquid chromatography on a 2-(1-pyrenyl)ethyldimethylsilylated silica column.

A rapid and simple liquid chromatographic method for the isolation of toxic planar polychlorinated biphenyls from their formulations by electron donor-acceptor high-performance liquid chromatography using a 2-(1-pyrenyl)ethyldimethylsilylated silica column is described. The separation takes less than 15 min and a complete analysis, including quantitation by gas chromatography-mass spectrometry or gas chromatography with electron-capture detection, may be completed in 60 min. Retention data for 105 individual polychlorinated biphenyl congeners are presented and the retention behaviour, as well as the mechanisms of separation, are discussed.