TexSe1-x Shortwave Infrared Photodiode Arrays with Monolithic Integration.

TexSe1-x shortwave infrared (SWIR) photodetectors show promise for monolithic integration with readout integrated circuits (ROIC), making it a potential alternative to conventional expensive SWIR photodetectors. However, challenges such as a high dark current density and insufficient detection performance hinder their application in large-scale monolithic integration. Herein, we develop a ZnO/TexSe1-x heterojunction photodiode and synergistically address the interfacial elemental diffusion and dangling bonds via inserting a well-selected 0.3 nm amorphous TeO2 interfacial layer. The optimized device achieves a reduced dark current density of -3.5 × 10-5 A cm-2 at -10 mV, a broad response from 300 to 1700 nm, a room-temperature detectivity exceeding 2.03 × 1011 Jones, and a 3 dB bandwidth of 173 kHz. Furthermore, for the first time, we monolithically integrate the TexSe1-x photodiodes on ROIC (64 × 64 pixels) with the largest-scale array among all TexSe1-x-based detectors. Finally, we demonstrate its applications in transmission imaging and substance identification.

(Bi,Sb)2 Se3 Alloy Thin Film for Short-Wavelength Infrared Photodetector and TFT Monolithic-Integrated Matrix Imaging.

Short-wavelength infrared photodetectors play a significant role in various fields such as autonomous driving, military security, and biological medicine. However, state-of-the-art short-wavelength infrared photodetectors, such as InGaAs, require high-temperature fabrication and heterogenous integration with complementary metal-oxide-semiconductor (CMOS) readout circuits (ROIC), resulting in a high cost and low imaging resolution. Herein, for the first time, a low-cost, high-performance, high-stable, and thin-film transistor (TFT) ROIC monolithic-integrated (Bi,Sb)2 Se3 alloy thin-film short-wavelength infrared photodetector is reported. The (Bi,Sb)2 Se3 alloy thin-film short-wavelength infrared photodetectors demonstrate a high external quantum efficiency (EQE) of 21.1% (light intensity of 0.76 µW cm-2 ) and a fast response time (3.24 µs). The highest EQE is about two magnitudes than that of the extrinsic photoconduction of Sb2 Se3 (0.051%). In addition, the unpackaged devices demonstrate high electric and thermal stability (almost no attenuation at 120 °C for 312 h), showing potential for in-vehicle applications that may experient such a high temperature. Finally, both the (Bi,Sb)2 Se3 alloy thin film and n-type CdSe buffer layer are directly deposited on the TFT ROIC (with a 64 × 64-pixel array) with a low-temperature process and the material identification and imaging applications are presented. This work is a significant breakthrough in ROIC monolithic-integrated short-wavelength infrared imaging chips.

Ligand-Engineered HgTe Colloidal Quantum Dot Solids for Infrared Photodetectors.

HgTe colloidal quantum dots (CQDs) are promising absorber systems for infrared detection due to their widely tunable photoresponse in all infrared regions. Up to now, the best-performing HgTe CQD photodetectors have relied on using aggregated CQDs, limiting the device design, uniformity and performance. Herein, we report a ligand-engineered approach that produces well-separated HgTe CQDs. The present strategy first employs strong-binding alkyl thioalcohol ligands to enable the synthesis of well-dispersed HgTe cores, followed by a second growth process and a final postligand modification step enhancing their colloidal stability. We demonstrate highly monodisperse HgTe CQDs in a wide size range, from 4.2 to 15.0 nm with sharp excitonic absorption fully covering short- and midwave infrared regions, together with a record electron mobility of up to 18.4 cm2 V-1 s-1. The photodetectors show a room-temperature detectivity of 3.9 × 1011 jones at a 1.7 µm cutoff absorption edge.

Phase-Transfer Exchange Lead Chalcogenide Colloidal Quantum Dots: Ink Preparation, Film Assembly, and Solar Cell Construction.

Solution-processed colloidal quantum dots (CQDs) are promising candidates for the third-generation photovoltaics due to their low cost and spectral tunability. The development of CQD solar cells mainly relies on high-quality CQD ink, smooth and dense film, and charge-extraction-favored device architectures. In particular, advances in the processing of CQDs are essential for high-quality QD solids. The phase transfer exchange (PTE), in contrast with traditional solid-state ligand exchange, has demonstrated to be the most promising approach for high-quality QD solids in terms of charge transport and defect passivation. As a result, the efficiencies of Pb chalcogenide CQD solar cells have been rapidly improved to 14.0%. In this review, the development of the PTE method is briefly reviewed for lead chalcogenide CQD ink preparation, film assembly, and device construction. Particularly, the key roles of lead halides and additional additives are emphasized for defect passivation and charge transport improvement. In the end, several potential directions for future research are proposed.

Cation-Exchange Enables In Situ Preparation of PbSe Quantum Dot Ink for High Performance Solar Cells.

Lead selenide (PbSe) colloidal quantum dots (CQDs) are promising candidates for optoelectronic applications. To date, PbSe CQDs capped by halide ligands exhibit improved stability and solar cells using these CQDs as active layers have reported a remarkable power conversion efficiency (PCE) up to 10%. However, PbSe CQDs are more prone to oxidation, requiring delicate control over their processability and compromising their applications. Herein, an efficient strategy that addresses this issue by an in situ cation-exchange process is reported. This is achieved by a two-phase ligand exchange process where PbI2 serves as both a passivating ligand and cation-source inducing transformation of CdSe to PbSe. The defect density and carrier lifetime of PbSe CQD films are improved to 1.05 × 1016  cm-3 and 12.2 ns, whereas the traditional PbSe CQD films possess 1.9 × 1016  cm-3 defect density and 10.2 ns carrier lifetime. These improvements are translated into an enhancement of photovoltaic performance of PbSe solar cells, with a PCE of up to 11.6%, ≈10% higher than the previous record. Notably, the approach enables greatly improved stability and a two-month stability is successfully demonstrated. This strategy is expected to promote the fast development of PbSe CQD applications in low-cost and high-performance optoelectronic devices.

[Study on low temperature moisture regain drying characteristics of different grades of Angelicae Sinensis Radix based on Weibull distribution function].

The drying process of different grades of Angelicae Sinensis Radix under low temperature and resurgence conditions was simulated based on the Weibull distribution function,in order to clarify the low-temperature moisture regain drying characteristics of different grades of Angelicae Sinensis Radix,and explore the effect of grade and drying conditions on the drying process of Angelicae Sinensis Radix. Research results indicated that the Weibull function can be used to simulate different grades of Angelicae Sinensis Radix low-temperature moisture regain drying process,and the lower the drying temperature,the smaller the grade,and the better the simulation effect. The grade and drying temperature showed a significant effect on the low-temperature moisture regain drying process of Angelicae Sinensis Radix,and the effect of temperature on the relative moisture regain rate of Angelicae Sinensis Radix was greater than the grade. The relative moisture regain rate of different grades of Angelicae Sinensis Radix at 40 ℃ was higher than 55 ℃,and the relative moisture regain rate at 40 ℃ was first class > second class > third class. After drying,the moisture ratio at 40 ℃ was lower than that at 55 ℃; the effect of the grade on the effective diffusion coefficient of dry water was greater than the temperature. Under different conditions of 40 ℃ and 55 ℃ moisture regain,the effective diffusion coefficient of water was between 2. 941 6×10-6-7. 991 5×10-6 and3. 093 8×10-6-8. 483 8×10-6 for different grades. Under the same temperature conditions,the effective diffusion coefficient of water was first class > second class > third class. Therefore,Weibull function can be used to study and simulate the drying characteristics of different grades of Angelicae Sinensis Radix under low-temperature moisture regain conditions,providing experimental basis for the improvement of traditional drying technology of Angelicae Sinensis Radix and the optimization of drying process of different specifications or grades of Angelicae Sinensis Radix.

Fluoride passivation of ZnO electron transport layers for efficient PbSe colloidal quantum dot photovoltaics.

Lead selenide (PbSe) colloidal quantum dots (CQDs) are suitable for the development of the next-generation of photovoltaics (PVs) because of efficient multiple-exciton generation and strong charge coupling ability. To date, the reported high-efficient PbSe CQD PVs use spin-coated zinc oxide (ZnO) as the electron transport layer (ETL). However, it is found that the surface defects of ZnO present a difficulty in completion of passivation, and this impedes the continuous progress of devices. To address this disadvantage, fluoride (F) anions are employed for the surface passivation of ZnO through a chemical bath deposition method (CBD). The F-passivated ZnO ETL possesses decreased densities of oxygen vacancy and a favorable band alignment. Benefiting from these improvements, PbSe CQD PVs report an efficiency of 10.04%, comparatively 9.4% higher than that of devices using sol-gel (SG) ZnO as ETL. We are optimistic that this interface passivation strategy has great potential in the development of solution-processed CQD optoelectronic devices.

Colloidal PbS Quantum Dot Photodiode Imager with Suppressed Dark Current.

Lead sulfide (PbS) colloidal quantum dots (CQDs) for photodetectors (PDs) have garnered great attention due to their potential use as low-cost, high-performance, and large-area infrared focal plane arrays. The prevailing device architecture employed for PbS CQD PDs is the p-i-n structure, where PbS CQD films treated with thiol molecules, such as 1,2-ethanedithiol (EDT), are widely used as p-type layers due to their favorable band alignment. However, PbS-EDT films face a critical challenge associated with low film quality, resulting in many defects that curtail the device performance. Herein, a controlled oxidization process is developed for better surface passivation of the PbS-EDT transport layer. The dark current density (Jd) of PbS CQD PDs based on optimized PbS-EDT layer shows a dramatic decrease by nearly 2 orders of magnitude. The increase of carrier lifetime and suppression of carrier recombination via controlled oxidation in PbS-EDT CQDs were confirmed by transient absorption spectra and electrochemical impedance spectra. The device based on the optimized PbS-EDT hole transport layer (HTL) exhibits a specific detectivity (D*) that is 3.4 times higher compared to the control device. Finally, the CQD PD employing oxidization PbS-EDT CQDs is integrated with a thin film transistor (TFT) readout circuit, which successfully accomplishes material discrimination imaging, material occlusion imaging, and smoke penetration imaging. The controlled oxidization strategy verifies the significance of surface management of CQD solids and is expected to help advance infrared optoelectronic applications based on CQDs.

Efficient PbSe Colloidal Quantum Dot Solar Cells Using SnO2 as a Buffer Layer.

PbSe colloidal quantum dots (CQDs) are widely used in solar cells because of their tunable band gap, solution processability, and efficient multiple exciton generation effect. The most efficient PbSe CQD solar cells use high-temperature-processed ZnO as the electron transport layer (ETL), limiting their applications in flexible photovoltaics. Currently, low-temperature solution-processed SnO2 has been demonstrated as an efficient ETL for high-efficient PbS CQD and perovskite solar cells because of less parasitic light absorption and higher electron mobility. Herein, we introduce low-temperature solution-processed SnO2 as ETL for PbSe CQD solar cells, and fabricate the PbSe CQD absorber layer with a one-step spin-coating method. The champion device with the structure of FTO (SnO2:F)/SnO2/PbSe-PbI2/PbS-EDT (1,2-ethanedithiol)/Au achieves a high open-circuit voltage of 577.1 mV, a short-circuit current density of 24.87 mA cm-2, a fill factor of 67%, and an impressive power conversion efficiency of 9.67%. Our results pave the way for the development of low-temperature flexible PbSe CQD solar cells.

Lead Selenide (PbSe) Colloidal Quantum Dot Solar Cells with >10% Efficiency.

Low-cost solution-processed lead chalcogenide colloidal quantum dots (CQDs) have garnered great attention in photovoltaic (PV) applications. In particular, lead selenide (PbSe) CQDs are regarded as attractive active absorbers in solar cells due to their high multiple-exciton generation and large exciton Bohr radius. However, their low air stability and occurrence of traps/defects during film formation restrict their further development. Air-stable PbSe CQDs are first synthesized through a cation exchange technique, followed by a solution-phase ligand exchange approach, and finally absorber films are prepared using a one-step spin-coating method. The best PV device fabricated using PbSe CQD inks exhibits a reproducible power conversion efficiency of 10.68%, 16% higher than the previous efficiency record (9.2%). Moreover, the device displays remarkably 40-day storage and 8 h illuminating stability. This novel strategy could provide an alternative route toward the use of PbSe CQDs in low-cost and high-performance infrared optoelectronic devices, such as infrared photodetectors and multijunction solar cells.