Biochar/sodium alginate mixed matrix membrane as adsorbent for in-syringe solid-phase extraction towards trace nitroimidazoles in water samples prior to ultra-high-performance liquid chromatography-tandem mass spectrometry analysis.

In the present work, the herb (Poria cocos (Schw.) Wolf) residue, as an environmentally friendly and renewable biomass source, was converted into novel biochar. Biochar/sodium alginate mixed matrix membrane was fabricated. On this basis, a biochar/sodium alginate mixed matrix membrane-based in-syringe solid-phase extraction was developed combined with ultra-high performance liquid chromatography-tandem mass spectrometry to determine nitroimidazoles in water samples. The factors including times of exaction, type, and volume of elution solvent, and sample solution pH were thoroughly optimized. Then the correlation coefficient was 0.9995-0.9997. The limit of detection of four analytes was between 0.006 and 0.014 ng/mL, and the recovery was between 79.02% and 99.1%. Consequently, the established method would provide a new perspective on monitoring nitroimidazoles in water samples.

Matrix complete dissolution concatenated biochar magnetic solid-phase extraction of benzotriazole ultraviolet stabilizers in polyester fibers prior to UPLC-MS/MS analysis.

Matrix complete dissolution combined with magnetic solid-phase extraction (MSPE) was applied to extract four benzotriazole ultraviolet stabilizers (BUVSs) from polyester curtains. Ultra-performance liquid chromatography tandem mass spectrometry was coupled to perform the content of trace BUVSs. The procedure was being developed in two steps. The polymer matrix was initially thoroughly dissolved by 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP) followed by the addition of precipitant to separate the target from the dissolved polymer matrix. Next, triiron tetraoxide/biochar magnetic material was prepared and utilized as the sorbent for purification of the extract. Ultrasonic extraction coupled with the MSPE method and the proposed method was compared. Better extraction recovery of four BUVSs was acquired by the novel developed extraction method. The purification effect of the new extraction method was established by comparing the matrix effect of the polymer complete dissolution method and the polymer complete dissolution combined with the MSPE method. The extraction parameters were investigated. Under the optimized conditions, correlation coefficient (r) ranging from 0.9969 to 0.9997, limit of detection of 0.2 to 0.8 ng·g-1, and the recovery varied from 81.5 to 102.7% with RSD smaller than 10.7% were obtained for four BUVSs, respectively. This study provides a potential strategy for the efficient extraction and sensitive determination of BUVSs in polyester fibers samples.

Effects of 4-nonylphenol on adipogenesis in 3T3-L1 preadipocytes and C3H/10T1/2 mesenchymal stem cells.

Obesogens are a subset of endocrine disruptor chemicals (EDCs) that cause obesity. The typical EDC 4-nonylphenol (4-NP) has been identified as an obesogen. However, the in vitro effects of 4-NP on adipogenesis remain unclear. In this study, 3T3-L1 preadipocytes and C3H/10T1/2 mesenchymal stem cells (MSCs) were used to investigate the influence of 4-NP on adipogenesis. The differentiation protocols for 3T3-L1 preadipocytes and C3H/10T1/2 MSCs took 8 and 12 days, respectively, beginning at Day 0. In differentiated 3T3-L1 preadipocytes, 20 µM 4-NP decreased cell viability on Days 4 and 8. Exposure to 4-NP inhibited triglyceride (TG) accumulation and adipogenic marker expression on Days 0-8, but the inhibitory effects were weaker on Days 2-8. The protein expression of pSTAT3 or STAT3 decreased on Days 0-8 and 2-8. Conversely, 4-NP promoted TG accumulation and the adipogenic marker expression in C3H/10T1/2 adipocytes. The opposing effects were attributed to physiological differences between the two cell lines. The 3T3-L1 preadipocytes are dependent on mitotic clonal expansion (MCE) to drive differentiation, while C3H/10T1/2MSCs and human preadipocytes are not. Additionally, 4-NP downregulated ß-catenin expression in C3H/10T1/2 adipocytes. Accordingly, we hypothesized that 4-NP promotes adipogenesis. The role of the canonical Wnt pathway in the promotion of adipogenesis by 4-NP requires further validation. This study provides new insights into the mechanisms and appropriate risk management of 4-NP.

Tannic acid-directed synthesis of magnetic and boronic acid-functionalized metal-organic frameworks for selective extraction and quantification of catecholamines in human urine.

A novel magnetic borate-functionalized metal-organic framework nanocomposite was designed and fabricated for selective enrichment of catecholamines from human urine. Firstly, the polytannic acid (PTA) layer with natural low-cost and ecofriendly polyphenol tannic acid as the organic ligand and Fe3+ as the cross-linker was coated onto the surface of Fe3O4. Then, the borate-functionalized metal-organic framework (MIL-100(Fe)-B) with 5-boronobenzene-1,3-dicarboxylic acid as a ligand fragment was modified onto the PTA-coated Fe3O4 through a metal-ligand-fragment coassembly strategy. The obtained smart porous adsorbent Fe3O4@PTA@MIL-100(Fe)-B was confirmed by means of several characterization methods and then applied as an effective magnetic solid phase extraction (MSPE) sorbent for specific extraction of trace catecholamines in human urine. The Plackett-Burman design was used for screening the variables significantly affecting the extraction efficiency. Then, the significant factors were further investigated by the Box-Behnken design to determine the optimal extraction conditions. Under the optimal conditions, a method for selective MSPE combined with high-performance liquid chromatography with a fluorescence detector for the quantitation of catecholamines in human urine was developed and validated. With the proposed method, the linearity range was from 0.500 to 500 ng mL-1 for norepinephrine and epinephrine and from 1.00 to 500 ng mL-1 for dopamine. The detection limits were 0.050, 0.11, and 0.20 ng mL-1 for norepinephrine, epinephrine, and dopamine, respectively. The recoveries from spiking experiments varied from 91.5 to 108% with relative standard deviations (RSDs) of 0.80-4.8%. The established method is rapid, sensitive, accurate, inexpensive, and ecofriendly and was successfully applied to the determination of the target catecholamines in human urine samples.

Triple-enzyme mimetic activity of Fe3O4@C@MnO2 composites derived from metal-organic frameworks and their application to colorimetric biosensing of dopamine.

Novel Fe3O4@C@MnO2 composites were successfully synthesized for the first time via an interfacial reaction between magnetic porous carbon and KMnO4, in which the magnetic porous carbon was derived from the pyrolysis of Fe-MIL-88A under N2 atmosphere. Interestingly, the obtained Fe3O4@C@MnO2 composites were found to have triple-enzyme mimetic activity including peroxidase-like, catalase-like, and oxidase-like activity. As a peroxidase mimic, Fe3O4@C@MnO2 composites could catalyze the oxidation of TMB into a blue oxidized product by H2O2. As a catalase mimic, Fe3O4@C@MnO2 could catalyze the decomposition of H2O2 to generate O2 and H2O. As an oxidase mimic, Fe3O4@C@MnO2 could catalyze the direct oxidation of TMB to produce a blue oxidized product without H2O2. Reactive oxygen species measurements revealed that the oxidase-like activity originated from 1O2 and O2-∙and little∙OH generated by the dissolved oxygen, which was catalyzed by the Fe3O4@C@MnO2 in the TMB oxidation reaction. The oxidase-like activity of Fe3O4@C@MnO2 was investigated in detail. Under the optimized conditions, a rapid, sensitive, visual colorimetric method for dopamine detection was developed based on the inhibitory effect of dopamine on the oxidase-like activity. The proposed method allows for dopamine detection with a limit of detection of 0.034 µM and a linear range of 0.125-10 µM. This new colorimetric method was successfully used for the determination of dopamine in human blood samples.

Preparation and application of novel MIL-101(Cr) composite in liquid chromatographic separation of aromatic compounds: experimental and computational insights.

A novel composite material of SiO2@dSiO2@MIL-101(Cr) was synthesized via SiO2@dSiO2 as the core and MIL-101(Cr) as the shell to separate aromatic compounds. The laboratory prepared column gave rise to the baseline separation of xylene, dichlorobenzene isomers, phthalate esters, nitrobenzene, and acetophenone with high column efficiency (e.g., 109,050 plates m-1 for methyl phthalate) and good precision (e.g., 0.02-0.05%, 0.24-0.34%, 0.14-0.18%, and 0.11-0.13% corresponding to the relative standard deviation of retention time, peak area, peak height, and half peak width for xylene isomers, respectively). The calculation of thermodynamic parameters demonstrated that the separation of o-xylene, nitrobenzene, acetophenone, and p-dichlorobenzene was controlled by positive ∆H and ∆S. Although the separation of aromatic compounds by a MOF packed column has been reported in many studies, the knowledge regarding their separation mechanism at atomic level is still very limited. In this study, we integrate fully atomistic molecular dynamics simulation and binding free energy calculation to investigate the separation mechanism of aromatic compounds by MIL-101(Cr). The investigation provides a base for separation of more and other compounds in the future. Graphical abstract.

High throughput sequencing of T-cell receptor repertoire using dry blood spots.

BACKGROUND: Immunology research, particularly next generation sequencing (NGS) of the immune T-cell receptor ß (TCRß) repertoire, has advanced progression in several fields, including treatment of various cancers and autoimmune diseases. This study aimed to identify the TCR repertoires from dry blood spots (DBS), a method that will help collecting real-world data for biomarker applications. METHODS: Finger-prick blood was collected onto a Whatman filter card. RNA was extracted from DBS of the filter card, and fully automated multiplex PCR was performed to generate a TCRß chain library for next generation sequencing (NGS) analysis of unique CDR3s (uCDR3). RESULTS: We demonstrated that the dominant clonotypes from the DBS results recapitulated those found in whole blood. According to the statistical analysis and laboratory confirmation, 40 of 2-mm punch disks from the filter cards were enough to detect the shared top clones and have strong correlation in the uCDR3 discovery with whole blood. uCDR3 discovery was neither affected by storage temperatures (room temperature versus - 20 °C) nor storage durations (1, 14, and 28 days) when compared to whole blood. About 74-90% of top 50 uCDR3 clones of whole blood could also be detected from DBS. A low rate of clonotype sharing, 0.03-1.5%, was found among different individuals. CONCLUSIONS: The DBS-based TCR repertoire profiling method is minimally invasive, provides convenient sampling, and incorporates fully automated library preparation. The system is sensitive to low RNA input, and the results are highly correlated with whole blood uCDR3 discovery allowing study scale-up to better understand the relationship and mutual influences between the immune and diseases.

The critical role for TAK1 in trichloroethylene-induced contact hypersensitivity in vivo and in CD4+ T cell function alteration by trichloroethylene and its metabolites in vitro.

Occupational exposure to trichloroethylene (TCE) has been associated with severe, generalized contact hypersensitivity (CHS) skin disorder, which is considered a delayed-type hypersensitivity reaction mediated by antigen-specific T cells. Transforming growth factor-ß activated kinase-1 (TAK1) is essential for regulating the development and effector function of T cells. We hypothesized that disrupting TAK1 activity might inhibit TCE-induced CHS response. In this study, a local lymph node assay was employed to build a CHS model induced by TCE combined with the inducible-TAK1 deletion system to study the effect of TAK1 on it. It was observed that TAK1 deficiency ameliorated the TCE-induced CHS response and was associated with defective T cell expansion and activation and IFN-γ production in vivo. Furthermore, we investigated the effects of TCE and its metabolites trichloroacetic acid (TCA) and dichloroacetic acid (DCA) on CD4+ T cell function and the effect of TAK1 on it in vitro. The results showed that TCE, TCA and DCA augmented the proliferation, activation and differentiation of CD4+ T cells through Jnk MAPK and NF-κB pathways. TAK1 deletion significantly attenuated these effects induced by TCE, TCA or DCA on CD4+ T cells. In conclusion, it is suggested that TAK1 plays a critical role both in TCE-induced CHS response in vivo and in TCE and its metabolite-induced CD4+ T cell activation in vitro. Local inhibition of TAK1 might offer a promising alternative feasible strategy for TCE-induced CHS.

Delayed development influences the outcome of different grades of D5 and D6 blastocysts during freeze-thaw cycle.

To analyze the effects of blastocysts on the 5th day (D5) and 6th day (D6) of frozen-thawed blastocyst transplantation on pregnancy outcome and provide evidence for further improvement of the strategy. This study included transfers from the Reproductive Medicine Center of the Second Affiliated Hospital of Wenzhou Medical University during freeze-thaw cycles from January 2016 to December 2017. They were divided into D5 group (1616 cases) and D6 group (619 cases) according to blastocyst formation and development. Each group was further divided into 5 groups according to the quality of the blastocyst and the number of transplants, making a total of 10 groups. Following the frozen transplantation cycle, the transplanting rate was significantly higher for D5 (41.73%) than for D6 (23.98%) (P < 0.05); the ongoing pregnancy rate (47,40%) was also significantly higher than that of D6 (28.43%) (P < 0.05).In the frozen-thawed blastocyst resuscitation transplantation, compared to D6 blastocysts, D5 blastocysts were more conducive to blastocyst implantation and could be used to achieve better clinical pregnancy outcome. In blastocyst selection, a single D5 excellent blastocyst transplant is preferred. Only at the 6th day of non-excellent D6, 2 blastocysts are recommended for transplantation.

Effects of bisphenol A on gap junctions in HaCaT cells as mediated by the estrogen receptor pathway.

Bisphenol A (BPA) is widely used as the raw material for the production of plastics and paper products. People can be exposed to BPA through dermal contact, particularly for cashiers in contact with thermal paper every day. BPA is a known endocrine disruptor that has been shown to be carcinogenic. Many tumors show weak gap junctional intercellular communication (GJIC) function. The aim of this study was to investigate the effects and possible mechanisms of BPA's action on GJIC of human HaCaT skin cells. The results showed that BPA increased cell proliferation rates, prolonged GJIC photobleaching fluorescence recovery times and reduced overall fluorescence recovery rates at 0.01, 0.1 and 1 µm. BPA downregulated connexin (Cx)26 mRNA level at 0.1 µm. Estrogen receptor (ER) antagonist ICI 182 780 at 5 nm partially blocked the above effects of BPA indicating involvement of the ER pathway with BPA exposure. However, BPA did not influence Cx43 mRNA and protein levels. Our immunofluorescence data showed that Cx26 was expressed in the cytoplasm and plasma membrane, and was involved in the formation of gap junctions between adjacent cells, while Cx43 was expressed only in the cytoplasm. Therefore, our data indicate that Cx26 gap junctions may be involved in the GJIC inhibition caused by BPA. In conclusion, our results indicate that BPA can promote human skin cell proliferation, inhibit skin cell GJIC function but not formation and downregulate Cx26 mRNA levels partially through the ER pathway. We hypothesize that BPA can exhibit carcinogenicity by inhibiting GJIC.

Endoplasmic reticulum stress contributed to ß1-adrenoceptor autoantibody-induced reduction of autophagy in cardiomyocytes.

Autophagy reduction has been confirmed as an important mechanism in apoptosis induction. Our previous study showed that decreased autophagy induced by ß1-adrenoceptor autoantibodies (ß1-AAs) enhanced cardiomyocyte apoptosis and contributed to heart failure progression. Endoplasmic reticulum stress (ERS) is known to be an important mechanism in intracellular homeostasis and is closely related to autophagy. However, ERS in ß1-AA-induced autophagy dysfunction of cardiomyocytes remains unclear. In this study, we used an active immunization rat model and H9c2 cardiomyocytes to study the role of ERS in ß1-AA-induced autophagy. Results showed that prolonged action of ß1-AAs significantly reduced the autophagy of myocardial tissues and H9c2 cardiomyocytes, and ERS and its related apoptotic pathways were significantly activated. Moreover, mRFP-GFP-LC3 double-labeled adenoviruses were used to detect cardiomyocyte autophagic flux to confirm that ß1-AAs caused a significant decrease in autophagic flux in H9c2 cardiomyocytes. The ERS inhibitor, 4-phenylbutyrate (4-PBA), partially attenuated the ß1-AA-induced reduction of cardiomyocyte autophagy, consistent with the effect of the mammalian target of rapamycin inhibitor rapamycin (Rapa). Compared to the pretreatment with 4-PBA or Rapa alone, pretreatment with the combination of 4-PBA and Rapa had a greater effect on attenuating the ß1-AA-induced decrease in autophagy and ß1-AA-induced apoptosis in cardiomyocytes. This study provides an experimental basis for the role of ß1-AAs in the homeostatic maintenance of cardiomyocytes in patients with heart failure with respect to autophagy and ERS.

Blue light filtered white light induces depression-like responses and temporary spatial learning deficits in rats.

OBJECTIVES: Ambient light has a vital impact on mood and cognitive functions. Blue light has been previously reported to play a salient role in the antidepressant effect via melanopsin. Whether blue light filtered white light (BFW) affects mood and cognitive functions remains unclear. The present study aimed to investigate whether BFW led to depression-like symptoms and cognitive deficits including spatial learning and memory abilities in rats, and whether they were associated with the light-responsive function in retinal explants. METHODS: Male Sprague-Dawley albino rats were randomly divided into 2 groups (n = 10) and treated with a white light-emitting diode (LED) light source and BFW light source, respectively, under a standard 12 : 12 h L/D condition over 30 days. The sucrose consumption test, forced swim test (FST) and the level of plasma corticosterone (CORT) were employed to evaluate depression-like symptoms in rats. Cognitive functions were assessed by the Morris water maze (MWM) test. A multi-electrode array (MEA) system was utilized to measure electro-retinogram (ERG) responses induced by white or BFW flashes. RESULTS: The effect of BFW over 30 days on depression-like responses in rats was indicated by decreased sucrose consumption in the sucrose consumption test, an increased immobility time in the FST and an elevated level of plasma CORT. BFW led to temporary spatial learning deficits in rats, which was evidenced by prolonged escape latency and swimming distances in the spatial navigation test. However, no changes were observed in the short memory ability of rats treated with BFW. The micro-ERG results showed a delayed implicit time and reduced amplitudes evoked by BFW flashes compared to the white flash group. CONCLUSIONS: BFW induces depression-like symptoms and temporary spatial learning deficits in rats, which might be closely related to the impairment of light-evoked output signals in the retina.

A triazine-based conjugated microporous polymer composite for magnetic solid phase extraction of 5-nitroimidazoles coupled with UPLC-MS/MS for quantification.

An attractive triazine-based conjugated microporous polymer (TCMP) was fabricated via the Friedel-Crafts reaction and magnetized by a simple reduction co-precipitation method for the first time. The morphology and textural properties of the as-synthesized materials were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, powder X-ray diffraction, N2 adsorption measurements, elemental analysis, and magnetic measurements. The resulting magnetic triazine-based conjugated microporous polymer (MTCMP) was introduced as an efficient adsorbent for vortex-assisted magnetic solid phase extraction (MSPE) coupled with ultra-high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) for the determination of trace 5-nitroimidazoles (5-NDZs) in environmental water samples. The TCMP has abundant delocalized π-electrons and N-containing triazine that can generate π-interactions, intermolecular hydrogen bonds, and electrostatic interactions with polar 5-NDZs. Extraction parameters affecting the recovery efficiency of five 5-NDZs (metronidazole, ronidazole, secnidazole, tinidazole, and ornidazole), including the amount of the adsorbent, the pH value of the sample, the salting-out effect, the adsorption and elution time, and types and volume of the elution solvents, were investigated. Under the optimal conditions, a wide linear range, acceptable recoveries (ranging from 82.62% to 110.9% with the relative standard deviation lower than 9.58%), and good reproducibility (relative standard deviations less than 8.81% for intra-day and inter-day precision) were obtained. The limits of detection for the five analytes were between 0.012 and 0.035 ng mL-1. The established method is rapid, has high sensitivity and accuracy, and has been successfully applied to the detection of 5-NDZs in real environmental water samples.

Development and application of metal organic framework/chitosan foams based on ultrasound-assisted solid-phase extraction coupling to UPLC-MS/MS for the determination of five parabens in water.

In this work, a variety of highly porous metal organic framework/chitosan (MOF/CS) foams (MIL-53(Al)/CS, MIL-53(Fe)/CS, MIL-101(Cr)/CS, MIL-101(Fe)/CS, UiO-66(Zr)/CS, and MIL-100(Fe)/CS) were designed and prepared by an ice-templating process. The introduction of MOFs made these foams achieve excellent inherent characters in terms of strength, stability, and adsorption ability. The MOFs incorporated in the foams retained their unique properties. Additionally, the foams were durable and their adsorption abilities had only a little loss after being recycled several times. MIL-53(Al)/CS foam was selected as an adsorbent candidate to develop an ultrasound-assisted solid-phase extraction (UA-SPE) method for the first time, owing to its particularly noteworthy performance among the prepared MOF/CS foams. The method was then successfully applied to extract trace amount of five parabens (methylparaben, ethylparaben, propylparaben, butylparaben, benzylparaben) in water samples, followed by ultra-performance liquid chromatography coupled with tandem mass spectrometry (UPLC-MS/MS) detection. Several experimental parameters were investigated. Under the optimal conditions, the linear ranges were 0.5-200 µg/L with regression coefficients (r2) from 0.9948 to 0.9983. The method detection limits were between 0.09 and 0.45 µg/L. The recoveries ranged from 78.75 to 102.1% with relative standard deviations (RSDs) < 7.4%. Furthermore, the molecular interactions and free binding energies between MOFs and parabens were calculated by means of molecular docking to explain the adsorption mechanism deeply. The novel method proposed in this work exhibited many benefits such as easy operation, high enrichment efficiency, less solvent consuming, and higher sensitivity. Such a strategy would expand the application prospect of MOFs in sample pretreatment. Graphical abstract ᅟ.

An amino-functionalized magnetic framework composite of type Fe3O4-NH2@MIL-101(Cr) for extraction of pyrethroids coupled with GC-ECD.

An amino-functionalized magnetic framework composite of type Fe3O4-NH2@MIL-101(Cr) was synthesized using a solvothermal method. The material was characterized by scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, nitrogen adsorption, and magnetometry. The composite combines the advantages of amino-modified Fe3O4 and MIL-101(Cr). The presence of amino groups facilitates the fairly specific adsorption of pyrethroids. The composite was employed as a sorbent for magnetic solid phase extraction of five pyrethroids from environmental water samples. Following desorption with acidified acetone, the pyrethroids were quantified by gas chromatography with electron capture detection. The detection limits for bifenthrin, fenpropathrin, λ-cyhalothrin, permethrin, and deltamethrin range from 5 to 9 pg·mL-1. The method is rapid, accurate, and highly sensitive. The molecular interactions and free binding energies between MIL-101(Cr) and the five pyrethroids were calculated by means of molecular docking. Graphical abstract A novel functionalized magnetic framework composite of type Fe3O4-NH2@MIL-101(Cr) was synthesized. It was applied as a sorbent for magnetic solid phase extraction of pyrethroids prior to their quantitation by gas chromatography with electron capture detection. The molecular interactions of analytes and MIL-101(Cr) were studied.

Solid-phase extraction in combination with dispersive liquid-liquid microextraction and ultra-high performance liquid chromatography-tandem mass spectrometry analysis: the ultra-trace determination of 10 antibiotics in water samples.

A novel method, solid-phase extraction combined with dispersive liquid-liquid microextraction (SPE-DLLME), was developed for ultra-preconcentration of 10 antibiotics in different environmental water samples prior to ultra-high performance liquid chromatography-tandem mass spectrometry detection. The optimized results were obtained as follows: after being adjusted to pH 4.0, the water sample was firstly passed through PEP-2 column at 10 mL min(-1), and then methanol was used to elute the target analytes for the following steps. Dichloromethane was selected as extraction solvent, and methanol/acetonitrile (1:1, v/v) as dispersive solvent. Under optimal conditions, the calibration curves were linear in the range of 1-1000 ng mL(-1) (sulfamethoxazole, cefuroxime axetil), 5-1000 ng mL(-1) (tinidazole), 10-1000 ng mL(-1) (chloramphenicol), 2-1000 ng mL(-1) (levofloxacin oxytetracycline, doxycycline, tetracycline, and ciprofloxacin) and 1-400 ng mL(-1) (sulfadiazine) with a good precision. The LOD and LOQ of the method were at very low levels, below 1.67 and 5.57 ng mL(-1), respectively. The relative recoveries of the target analytes were in the range from 64.16% to 99.80% with relative standard deviations between 0.7 and 8.4%. The matrix effect of this method showed a great decrease compared with solid-phase extraction and a significant value of enrichment factor (EF) compared with dispersive liquid-liquid microextraction. The developed method was successfully applied to the extraction and analysis of antibiotics in different water samples with satisfactory results.

Experimental and molecular docking investigation on metal-organic framework MIL-101(Cr) as a sorbent for vortex assisted dispersive micro-solid-phase extraction of trace 5-nitroimidazole residues in environmental water samples prior to UPLC-MS/MS analysis.

In the presented work, metal-organic framework (MOF) material MIL-101(Cr) (MIL, Matérial Institute Lavoisier) was used as a sorbent for vortex assisted dispersive micro-solid-phase extraction (VA-D-µ-SPE) of trace amount of metronidazole (MNZ), ronidazole (RNZ), secnidazole (SNZ), dimetridazole (DMZ), tinidazole (TNZ), and ornidazole (ONZ) in different environmental water samples. Ultra-high-performance liquid chromatography coupled with tandem mass spectrometry (UPLC-MS/MS) was used to quantify the target analytes. The extraction conditions, including type of sorbents, amount of MIL-101(Cr), solution pH, extraction method, extraction time, effect of salt, and elution conditions were investigated. Upon the optimal conditions, the developed method showed an excellent extraction performance with the average recovery ranging from 75.2 to 98.8 %. Good sensitivity levels were achieved with the detection limits of 0.03∼0.06 µg/L and the quantitation limits of 0.09∼0.20 µg/L. The linear ranges were varied from 0.1 to 20 for SNZ and ONZ and from 0.2 to 40 µg/L for MNZ, RNZ, DMZ, and TNZ (r 2 > 0.992), and repeatability of the method was satisfactory with the relative standard deviations (RSD) <8 %. Ultimately, the applicability of the method was successfully confirmed by the extraction and determination of 5-nitroimidazoles (5-NDZs) in 12 real water samples, showing the positive findings of MNZ and TNZ ranging from 0.3 to 1.0 µg/L. Furthermore, molecular docking was applied to explain the molecular interactions and free binding energies between MIL-101(Cr) and 5-NDZs, providing a deep insight into the adsorption mechanism. The proposed method exhibited the advantages of simplicity, rapidly, less solvent consumption, ease of operation, higher sensitivity, and lower matrix effect. Graphical abstract Schematic diagram of the extraction process and molecular docking investigation.

Metal-organic framework MIL-101(Cr) as a sorbent of porous membrane-protected micro-solid-phase extraction for the analysis of six phthalate esters from drinking water: a combination of experimental and computational study.

An attractive metal-organic framework (MOF) MIL-101(Cr) material was synthesized at the nanoscale and applied as a sorbent in the porous membrane-protected micro-solid-phase extraction (µ-SPE) device for the pre-concentration of phthalate esters (PAEs) in drinking water samples for the first time. Parameters influencing the extraction efficiency, such as the selection of sorbent materials, pH adjustment, the effect of salt, magnetic-stirring extraction time, the desorption solvent and the desorption time, were investigated. Under the optimum conditions, the limits of detection from gas chromatography-mass spectrometric analysis for PAEs varied from 0.004 to 0.02 µg L(-1). The linear ranges were from 0.1 to 50 µg L(-1) or from 0.2 to 50 µg L(-1) for the analytes with the relative standard deviations fluctuating from 0.8 to 10.9% (n = 5). The enrichment factors (EFs) for the target PAEs were varied from 143 to 187. MIL-101(Cr) exhibited remarkable advantages compared to activated carbon and MIL-100(Fe). On the other hand, the computational method was first used to predict the adsorption of MIL-101(Cr) towards PAEs. The molecular interactions and the free binding energies between MIL-101(Cr) and PAEs were observed and calculated in terms of the molecular modeling method. MIL-101(Cr) showed high potential in the analysis of PAEs at trace levels in drinking water. The computational result was consistent with the detected enrichment factors. The computational modeling accurately predicted the extraction efficiency of MOF-based material towards the target analytes. Therefore, the combination of experimental and computational study provided a new strategy on the trace contaminant analysis.

Characterization of chemical constituents in Zhi-Zi-Da-Huang decoction by ultra high performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry.

A sensitive and reliable ultra high performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry method was established to separate and identify the chemical constituents of Zhi-Zi-Da-Huang decoction, a classic traditional Chinese medicine formula. The chromatographic separation was achieved on a Shim-pack XR-ODS C18 column (75 × 3.0 mm, 2.2 µm) using a gradient elution program. The detection was performed on a Waters Xevo G2 Q-TOF mass spectrometer equipped with electrospray ionization source in both positive and negative modes. With the optimized conditions, a total of 82 compounds were identified or tentatively characterized. Of the 82 compounds, 21 compounds were identified by comparing the retention time and MS data with reference standards, the rest were characterized by analyzing MS data and retrieving the reference literature. In addition, 31 compounds were identified from Gardenia jasminoides Ellis, ten compounds were identified from Rheum palmatum L., 33 compounds were identified from Citrus aurantium L., and eight compounds were identified from Sojae Semen Praeparatum. Results indicated that iridoids, anthraquinones, flavonoids, isoflavonoids, coumarins, glycosides of crocetin, monoterpenoids, and organic acids were major constituents in Zhi-Zi-Da-Huang decoction. It is concluded that the developed ultra high performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry method with high sensitivity and resolution is suitable for identifying and characterizing the chemical constituents of Zhi-Zi-Da-Huang decoction, and the analysis provides a helpful chemical basis for further research on Zhi-Zi-Da-Huang decoction.

A dispersive liquid-liquid microextraction method based on the solidification of a floating organic drop combined with HPLC for the determination of lovastatin and simvastatin in rat urine.

A dispersive liquid-liquid microextraction method based on solidification of floating organic drop combined with HPLC was developed for the determination of lovastatin and simvastatin in rat urine for the first time. 1-Dodecanol and methanol were used as the extraction and disperser solvents, respectively. Several important parameters influencing the micro-extraction efficiency were studied and systematically optimized, including the type and volume of extraction solvent and disperser solvent, extraction time, pH and salt concentration. The analytes were separated on a Kromasil C18 column at 30°C with a mobile phase of methanol and 0.2% acetic acid in water (83:17, v/v) and detected at 238 nm. Under the optimal conditions, the maximum number of enrichment factors for both analytes was 27. The linear ranges were 20.08-1004 and 20.00-1000 µg/L with the correlation coefficients ranging from 0.9990 to 0.9994 for lovastatin and simvastatin, respectively. The volume of organic solvent consumed in extraction was <0.3 mL, and the extraction time was 10 min. The newly developed environment-friendly sample pretreatment method will be a good alternative to conventional techniques, such as solid-phase extraction, liquid-liquid extraction and protein precipitation, for the HPLC determination of lovastatin and simvastatin in biological samples.