Adjuvanted influenza-H1N1 vaccination reveals lymphoid signatures of age-dependent early responses and of clinical adverse events.

Adjuvanted vaccines afford invaluable protection against disease, and the molecular and cellular changes they induce offer direct insight into human immunobiology. Here we show that within 24 h of receiving adjuvanted swine flu vaccine, healthy individuals made expansive, complex molecular and cellular responses that included overt lymphoid as well as myeloid contributions. Unexpectedly, this early response was subtly but significantly different in people older than ∼35 years. Wide-ranging adverse clinical events can seriously confound vaccine adoption, but whether there are immunological correlates of these is unknown. Here we identify a molecular signature of adverse events that was commonly associated with an existing B cell phenotype. Thus immunophenotypic variation among healthy humans may be manifest in complex pathophysiological responses.

Repeat expansions confer WRN dependence in microsatellite-unstable cancers.

The RecQ DNA helicase WRN is a synthetic lethal target for cancer cells with microsatellite instability (MSI), a form of genetic hypermutability that arises from impaired mismatch repair1-4. Depletion of WRN induces widespread DNA double-strand breaks in MSI cells, leading to cell cycle arrest and/or apoptosis. However, the mechanism by which WRN protects MSI-associated cancers from double-strand breaks remains unclear. Here we show that TA-dinucleotide repeats are highly unstable in MSI cells and undergo large-scale expansions, distinct from previously described insertion or deletion mutations of a few nucleotides5. Expanded TA repeats form non-B DNA secondary structures that stall replication forks, activate the ATR checkpoint kinase, and require unwinding by the WRN helicase. In the absence of WRN, the expanded TA-dinucleotide repeats are susceptible to cleavage by the MUS81 nuclease, leading to massive chromosome shattering. These findings identify a distinct biomarker that underlies the synthetic lethal dependence on WRN, and support the development of therapeutic agents that target WRN for MSI-associated cancers.

A structural variation reference for medical and population genetics.

Structural variants (SVs) rearrange large segments of DNA1 and can have profound consequences in evolution and human disease2,3. As national biobanks, disease-association studies, and clinical genetic testing have grown increasingly reliant on genome sequencing, population references such as the Genome Aggregation Database (gnomAD)4 have become integral in the interpretation of single-nucleotide variants (SNVs)5. However, there are no reference maps of SVs from high-coverage genome sequencing comparable to those for SNVs. Here we present a reference of sequence-resolved SVs constructed from 14,891 genomes across diverse global populations (54% non-European) in gnomAD. We discovered a rich and complex landscape of 433,371 SVs, from which we estimate that SVs are responsible for 25-29% of all rare protein-truncating events per genome. We found strong correlations between natural selection against damaging SNVs and rare SVs that disrupt or duplicate protein-coding sequence, which suggests that genes that are highly intolerant to loss-of-function are also sensitive to increased dosage6. We also uncovered modest selection against noncoding SVs in cis-regulatory elements, although selection against protein-truncating SVs was stronger than all noncoding effects. Finally, we identified very large (over one megabase), rare SVs in 3.9% of samples, and estimate that 0.13% of individuals may carry an SV that meets the existing criteria for clinically important incidental findings7. This SV resource is freely distributed via the gnomAD browser8 and will have broad utility in population genetics, disease-association studies, and diagnostic screening.

Long Noncoding RNA lnc-TCEA1-3 Affects Osteoclastic Function by Regulating ATP6V1H.

H subunit of V-ATPase (ATP6V1H) is specifically expressed in osteoclasts and its deficiency lead to osteoporosis. Our group previously found four intronic SNPs of ATP6V1H related to reduced bone mineral density, but the mechanisms was not clear. In this study, we found that the above four SNPs were located at lncRNA lnc-TCEA1-3 by using bioinformatics analysis. We further detected the function of lnc-TCEA1-3 on regulating ATP6V1H and osteoclast function using Atp6v1h knockout mice, lentivirus transfection and qPCR analysis. Over expression of lnc-TCEA1-3 up regulated the expression of ATP6V1H in HEK293 cells, HOS cells and primarily cultured osteoclasts, and increased the number of primarily cultured osteoclasts. In addition, over expression of lnc-TCEA1-3 exerted distinct effect on two transcripts of ATP6V1H in HEK293, HOS and osteoclasts. This study will facilitate the in-depth analysis of the effects of ATP6V1H on bone diseases, and discover new therapeutic strategies.

Expectations and blind spots for structural variation detection from long-read assemblies and short-read genome sequencing technologies.

Virtually all genome sequencing efforts in national biobanks, complex and Mendelian disease programs, and medical genetic initiatives are reliant upon short-read whole-genome sequencing (srWGS), which presents challenges for the detection of structural variants (SVs) relative to emerging long-read WGS (lrWGS) technologies. Given this ubiquity of srWGS in large-scale genomics initiatives, we sought to establish expectations for routine SV detection from this data type by comparison with lrWGS assembly, as well as to quantify the genomic properties and added value of SVs uniquely accessible to each technology. Analyses from the Human Genome Structural Variation Consortium (HGSVC) of three families captured ~11,000 SVs per genome from srWGS and ~25,000 SVs per genome from lrWGS assembly. Detection power and precision for SV discovery varied dramatically by genomic context and variant class: 9.7% of the current GRCh38 reference is defined by segmental duplication (SD) and simple repeat (SR), yet 91.4% of deletions that were specifically discovered by lrWGS localized to these regions. Across the remaining 90.3% of reference sequence, we observed extremely high (93.8%) concordance between technologies for deletions in these datasets. In contrast, lrWGS was superior for detection of insertions across all genomic contexts. Given that non-SD/SR sequences encompass 95.9% of currently annotated disease-associated exons, improved sensitivity from lrWGS to discover novel pathogenic deletions in these currently interpretable genomic regions is likely to be incremental. However, these analyses highlight the considerable added value of assembly-based lrWGS to create new catalogs of insertions and transposable elements, as well as disease-associated repeat expansions in genomic sequences that were previously recalcitrant to routine assessment.

Automated intelligent design of modified uni-traveling carrier photodectors.

This paper introduces an automatic intelligent design method for the modified uni-traveling carrier photodetector (MUTC-PD). The conventional photodetector design process often relies on the numerical solution of complex nonlinear partial differential equations to simulate and optimize device performance, which is not only computationally intensive but also inefficient. To overcome this challenge, we apply the charge control principle to calculate the photodetector bandwidth, which improves the computational speed by a factor of approximately 1800 compared to the numerical solution of nonlinear partial differential equations. To further optimize the structure of the photodetector, we incorporate the Velocity Varying Climbing Particle Swarm Optimization (VVCPSO) algorithm. This is an improved algorithm based on the traditional particle swarm algorithm, which is able to quickly find the optimal solution in a complex parameter space. By applying the VVCPSO algorithm, we successfully fine-tuned the photodetector structure and obtained structural parameters with optimal performance. Our thorough verification process confirms that the proposed method is consistent with the results of ATLAS simulation software. Automated design has resulted in a high-performance MUTC-PD with a responsivity of 0.52A/W and a bandwidth of 60 GHz (@-3 V) at a mesa diameter of 16µm. Compared to the pre-optimized device, the bandwidth is increased to three times the original. By reducing the mesa diameter to 4µm, the bandwidth can be further increased to 82 GHz (@-3 V). The proposed method's calculation speed is fast enough, enabling extensive parameter studies to optimize device performance.

Electrical feedback system for enhancing the RF power of photodetector.

In this paper, we propose a system for enhancing the RF output power of the photodetector, especially the power of fundamental tune and second-order harmonic, by feeding back part of the RF signal through an electrical feedback circuit. As a result of bias modulation and opto-electric mixing, the RF output power can be effectively enhanced. The structure of uni-traveling carrier photodetector (UTC-PD) is employed in this work. With the RF enhancement system, the power of fundamental tune and second-order harmonic improve by 6.4 dB and 9.9 dB respectively, under the condition of 26 dBm input optical power, 3 V bias voltage, and 14 GHz input optical signal. Further, it was observed that third-order harmonic appeared under the influence of this system.

Three-dimensional finite element analysis on stress distribution after different palatoplasty and levator veli palatini muscle reconstruction.

OBJECTIVES: To establish a three-dimensional finite element model of the upper palate, pharyngeal cavity, and levator veli palatini muscle in patients with unilateral complete cleft palate, simulate two surgical procedures that the two-flap method and Furlow reverse double Z method, observe the stress distribution of the upper palate soft tissue and changes in pharyngeal cavity area after different surgical methods, and verify the accuracy of the model by reconstructing and measuring the levator veli palatini muscle. MATERIALS AND METHODS: Mimics, Geomagic, Ansys, and Hypermesh were applied to establish three-dimensional finite element models of the pharyngeal cavity, upper palate, and levator veli palatini muscle in patients with unilateral complete cleft palate. The parameters including length, angle, and cross-sectional area of the levator veli palatini muscle etc. were measured in Mimics, and two surgical procedures that two-flap method and Furlow reverse double Z method were simulated in Ansys, and the area of pharyngeal cavity was measured by hypermesh. RESULTS: A three-dimensional finite element model of the upper palate, pharyngeal cavity, and bilateral levator veli palatini muscle was established in patients with unilateral complete cleft palate ; The concept of horizontal projection characteristics of the palatal dome was applied to the finite element simulation of cleft palate surgery, vividly simulating the displacement and elastic stretching of the two flap method and Furlow reverse double Z method during the surgical process; The areas with the highest stress in the two-flap method and Furlow reverse double Z method both occur in the hard soft palate junction area; In resting state, as measured, the two flap method can narrow the pharyngeal cavity area by 50.9%, while the Furlow reverse double Z method can narrow the pharyngeal cavity area by 65.4%; The measurement results of the levator veli palatini muscle showed no significant difference compared to previous studies, confirming the accuracy of the model. CONCLUSIONS: The finite element method was used to establish a model to simulate the surgical procedure, which is effective and reliable. The area with the highest postoperative stress for both methods is the hard soft palate junction area, and the stress of the Furlow reverse double Z method is lower than that of the two-flap method. The anatomical conditions of pharyngeal cavity of Furlow reverse double Z method are better than that of two-flap method in the resting state. CLINICAL RELEVANCE: This article uses three-dimensional finite element method to simulate the commonly used two-flap method and Furlow reverse double Z method in clinical cleft palate surgery, and analyzes the stress distribution characteristics and changes in pharyngeal cavity area of the two surgical methods, in order to provide a theoretical basis for the surgeon to choose the surgical method and reduce the occurrence of complications.

SNR Enhancement for Comparator-Based Ultra-Low-Sampling Φ-OTDR System Using Compressed Sensing.

The large amount of sampled data in coherent phase-sensitive optical time-domain reflectometry (Φ-OTDR) brings heavy data transmission, processing, and storage burdens. By using the comparator combined with undersampling, we achieve simultaneous reduction of sampling rate and sampling resolution in hardware, thus greatly decreasing the sampled data volume. But this way will inevitably cause the deterioration of detection signal-to-noise ratio (SNR) due to the quantization noise's dramatic increase. To address this problem, denoising the demodulated phase signals using compressed sensing, which exploits the sparsity of spectrally sparse vibration, is proposed, thereby effectively enhancing the detection SNR. In experiments, the comparator with a sampling parameter of 62.5 MS/s and 1 bit successfully captures the 80 MHz beat signal, where the sampled data volume per second is only 7.45 MB. Then, when the piezoelectric transducer's driving voltage is 1 Vpp, 300 mVpp, and 100 mVpp respectively, the SNRs of the reconstructed 200 Hz sinusoidal signals are respectively enhanced by 23.7 dB, 26.1 dB, and 28.7 dB by using compressed sensing. Moreover, multi-frequency vibrations can also be accurately reconstructed with a high SNR. Therefore, the proposed technique can effectively enhance the system's performance while greatly reducing its hardware burden.

Improved performance of InGaAs/AlGaAs quantum well lasers on silicon using InAlAs trapping layers.

InGaAs/AlGaAs multiple quantum well lasers grown on silicon (001) by molecular beam epitaxy have been demonstrated. By inserting InAlAs trapping layers into AlGaAs cladding layers, misfit dislocations easily located in the active region can be effectively transferred out of the active region. For comparison, the same laser structure without the InAlAs trapping layers was also grown. All these as-grown materials were fabricated into Fabry-Perot lasers with the same cavity size of 20 × 1000 µm2. The laser with trapping layers achieved a 2.7-fold reduction in threshold current density under pulsed operation (5 µs-pulsed width, 1%-duty cycle) compared to the counterpart, and further realized a room-temperature continuous-wave lasing with a threshold current of 537 mA which corresponds to a threshold current density of 2.7 kA/cm2. When the injection current reached 1000 mA, the single-facet maximum output power and slope efficiency were 45.3 mW and 0.143 W/A, respectively. This work demonstrates significantly improved performances of InGaAs/AlGaAs quantum well lasers monolithically grown on silicon, providing a feasible solution to optimize the InGaAs quantum well structure.

Simulation and design of a high-speed and high-power modified uni-traveling carrier photodiode based on the electric field distribution in the depletion region.

A modified uni-traveling carrier photodiode with an electric field control layer is proposed to achieve high-speed and high-power performance at a lower bias voltage. By inserting the 10 nm p-type InGaAs electric field control layer between the intrinsic absorption layer and space layer, the electric field distribution in the depleted absorption layer and depleted non-absorption layer can be changed. It is beneficial for reducing power consumption and heat generation, meanwhile suppressing the space-charge effect. Compared with the original structure without the electric field control layer, the 3 dB bandwidth of the 20 µm diameter novel structure, to the best of our knowledge, is improved by 27.1% to 37.5 GHz with a reverse bias of 2 V, and the RF output power reaches 23.9 dBm at 30 GHz. In addition, under 8 V bias voltage, the bandwidth reaches 47.3 GHz.

High Q-factor Fano resonances based on a permittivity-asymmetric dielectric pea-shaped cylinder.

We numerically investigate two Fano resonances with high Q-factors based on a permittivity-asymmetric metastructure composed of two pea-shaped cylinders. By employing different materials to break the permittivity-asymmetry, the quasi-bound state of the continuum spectrum (BIC) resonance at 982.87 nm is excited, showing the Q-factor as high as 8183.7. The electromagnetic fields and vectors are analyzed by using the finite-difference time-domain (FDTD) method, and the resonance modes are identified as magnetic dipole (MD) responses and MDs by multipole decomposition in Cartesian coordinates, displaying that the light is confined within a pea-shaped cylinder to achieve localized field enhancement. In addition, the sensing performances of the metastructure are evaluated, and an optical refractive index sensor can be obtained with the sensitivity of 152 nm/RIU and maximum figure of merit (FOM) of 832.6. This proposed structure offers a new, to the best of our knowledge, way to achieve Fano resonant excitation on all-dielectric metastructures and can be used in nonlinear optics, biosensing, optical switches, and lasers.

Endoplasmic reticulum chaperone GRP78 participates in fluoride-induced autophagy in LS8 cells by regulating the IRE1-TRAF2-JNK pathway.

Fluoride induces endoplasmic reticulum (ER) stress in ameloblasts, which is responsible for enamel mineralization disorder. Fluoride induces autophagy in ameloblasts, but the molecular mechanisms through which ameloblasts respond to fluoride-induced cellular stress and autophagy remain unclear. This study investigated ER stress-induced autophagy and the regulatory role of the ER molecular chaperone GRP78 in fluoride-induced autophagy in ameloblast LS8 cells. To explore the relationship between fluoride-induced ER stress and autophagy, we assessed changes in fluoride-induced autophagy in LS8 cells following overexpression and/or silencing of the ER stress molecular chaperone GRP78. We found that autophagy induced by fluoride was further increased after GRP78 overexpression in LS8 cells. Fluoride-induced autophagy was reduced in GRP78-silenced LS8 cells. Furthermore, we found that ER stress can regulate autophagy in fluoride-treated ameloblasts (LS8 cells) and that the GRP78/IRE1/TRAF2/JNK pathway is involved in the underlying regulation. Our study suggests that ER stress plays a role in fluoride-induced damage by inducing ameloblast autophagy.

A Phase-Sensitive Optical Time Domain Reflectometry with Non-Uniform Frequency Multiplexed NLFM Pulse.

In the domain of optical fiber distributed acoustic sensing, the persistent challenge of extending sensing distances while concurrently improving spatial resolution and frequency response range has been a complex endeavor. The amalgamation of pulse compression and frequency division multiplexing methodologies has provided certain advantages. Nevertheless, this approach is accompanied by the drawback of significant bandwidth utilization and amplified hardware investments. This study introduces an innovative distributed optical fiber acoustic sensing system aimed at optimizing the efficient utilization of spectral resources by combining compressed pulses and frequency division multiplexing. The system continuously injects non-linear frequency modulation detection pulses spanning various frequency ranges. The incorporation of non-uniform frequency division multiplexing augments the vibration frequency response spectrum. Additionally, nonlinear frequency modulation adeptly reduces crosstalk and enhances sidelobe suppression, all while maintaining a favorable signal-to-noise ratio. Consequently, this methodology substantially advances the spatial resolution of the sensing system. Experimental validation encompassed the multiplexing of eight frequencies within a 120 MHz bandwidth. The results illustrate a spatial resolution of approximately 5 m and an expanded frequency response range extending from 1 to 20 kHz across a 16.3 km optical fiber. This achievement not only enhances spectral resource utilization but also reduces hardware costs, making the system even more suitable for practical engineering applications.

High slope-efficiency quantum-dot lasers grown on planar exact silicon (001) with asymmetric waveguide structures.

We report electrically pumped continuous-wave (CW) InAs/GaAs quantum dot lasers directly grown on planar exact silicon (001) with asymmetric waveguide structures. Surface hydrogen-annealing for the GaAs/ Si (001) templates and low-temperature growth for GaInP upper cladding layers were combined in the growth of the laser structure to achieve a high slope efficiency. For the broad-stripe edge-emitting lasers with 2-mm cavity length and 20-µm stripe width made from the above laser structure, a threshold current density of 203.5 A/cm2 and a single-facet slope efficiency of 0.158 W/A are achieved at ∼1.31 µm band under CW conditions. The extrapolated mean-time-to-failure reaches up to 21000 hours at room temperature, which is deduced from the data measured from C-mount packaged devices. Importantly, these results can provide a practical strategy to realize 1.3 µm wavelength band distributed feedback lasers directly on planar exact Si (001) templates with thin buffer layers.

Inverse design of sub-wavelength convergent grating based on the "stepped particle swarm algorithm".

In this Letter, a novel "stepped particle swarm optimization" (SPSO) based on field intensity adjustment is proposed. After that, we used this algorithm to design a sub-wavelength converging grating that could be integrated with the detector on the back. Firstly, the advantages of reverse design in the process of two-dimensional or multi-element grating pattern design were summarized by comparing the theory of forward and reverse design. Then, the common "particle swarm optimization" (PSO) and our proposal were compared in the reverse design process; we found that the field strength at the focal point obtained by the improved algorithm was approximately twice of the conventional PSO, and the SPSO had higher computational efficiency and better global convergence. The value of the SPSO had been steadily enlarged, which significantly improved the performance of the sub-wavelength convergent grating. Finally, the property of the sub-wavelength converging grating was simulated, and we found that the grating could achieve good convergence in the focal length range of 100-150 µm, and had a strong ability to compensate for the position deviation of the incident light. In actual optical communications, this sub-wavelength converging grating will play an important role in alleviating the bandwidth and quantum efficiency, improving the performance of the detectors.

Topological inverse design of fabrication-constrained nanophotonic devices via an adaptive projection method.

Topology optimization has been widely adopted in the inverse design of nanophotonic devices due to low computation cost, which unfortunately produces intermediate relative permittivity values that fail to meet fabrication constraints. Additionally, the postprocessing required inevitably increases the complexity of the inverse design. In this Letter, we propose an adaptive projection method for topology optimization, in which a two-level hierarchical hyperbolic tangent projection function with linear increment and differentiation is constructed and applied to eliminate inherent defects of conventional topology optimization. Two binarized nanophotonic devices have been designed by our adaptive projection method, among which one ultra-compact dual 90°-bend waveguide reduces the average insertion loss to 20.3% of its similar counterpart and shows an 8.1% reduction for the average crosstalk in the O band, the other ultralow-loss waveguide crossing features an average insertion loss as low as 0.09 dB. With the significant advantages of excellent performance guarantee and fabrication-friendly geometry control fully demonstrated, our inverse design solution shows potential to contribute to nanophotonic devices and integrated chips.

Association of latent class analysis-derived subphenotypes of acute kidney injury with mortality in critically ill patients with cardiovascular disease: a retrospective cohort study.

BACKGROUND: To explore the potential heterogeneity of acute kidney injury (AKI) and evaluate the prognostic differences among AKI subphenotypes in critically ill patients with cardiovascular diseases. METHODS: Data were extracted from the Medical Information Mart for Intensive Care (MIMIC)-III database. Latent class analysis (LCA) was used to explore the potential subphenotypes of AKI in critically ill patients with cardiovascular diseases. The number of classes was identified by the Bayesian information criterion and entropy. The differences in prognostic ability among the AKI subphenotypes were evaluated by logistic regression analysis. RESULT: A total of 7738 AKI patients were enrolled in this study. Using LCA, AKI patients were divided into 4 heterogeneous subphenotypes, which were obviously different from the Kidney Disease: Improving Global Outcomes (KDIGO) stages. Interestingly, class 3 classified by LCA was dominated by stage 2, while the mortality rate in class 3 was significantly different from that in class 1 (15.2% vs. 1.6%, p < 0.05). After further adjustment, the mortality rate in class 3 remained higher than that in class 1, with an odds ratio of 12.31 (95% confidence interval, 8.96-16.89). CONCLUSIONS: LCA was feasible for AKI classification in critically ill patients with cardiovascular disease, and 4 distinct subphenotypes of AKI patients with different prognoses were identified. Our results highlighted the potential heterogeneity of AKI patients, which is worthy of further investigation.