Comparative investigation of tellurium-doped transition metal nanoparticles (Zn, Sn, Mn): Unveiling their superior photocatalytic and antibacterial activity.

In this study, tellurium-doped and undoped metal oxide nanoparticles (NPs) (ZnO, Mn3O4, SnO2) are compared, and a practical method for their synthesis is presented. Nanocomposites were created using the coprecipitation process, and comparisons between the three material categories under study were made using a range of characterization methods. The produced materials were subjected to structural, morphological, elemental composition, and functional group analyses using XRD, FESEM in combination with EDS, and FTIR. The optical characteristics in terms of cutoff wavelength were evaluated using UV-visible spectroscopy. Catalyzing the breakdown of methylene blue (MB) dye, the isolated nanocomposites demonstrated very consistent behavior when utilized as catalysts. Regarding both doped and undoped ZnO NPs, the maximum percentage of degradation was found to be 98% when exposed to solar Escherichia coli and Staphylococcus aureus, which stand for gram-positive and gram-negative bacteria, respectively, and were chosen as model strains for both groups using the disk diffusion technique in the context of in vitro antibacterial testing. Doped and undoped ZnO NPs exhibited greater antibacterial efficacy, with significant inhibition zones measuring 31.5 and 37.8 mm, compared with other metal oxide NPs.

Harnessing solar power for enhanced photocatalytic degradation of coloured pollutants using novel Mg-doped-ZnFe2O4/S@g-C3N4 heterojunction: A facile hydrothermal synthesis approach.

The ability of heterogeneous photocatalysis to effectively remove organic pollutants from wastewater has shown great promise as a tool for environmental remediation. Pure zinc ferrites (ZnFe2O4) and magnesium-doped zinc ferrites (Mg@ZnFe2O4) with variable percentages of Mg (0.5, 1, 3, 5, 7, and 9 mol%) were synthesized via hydrothermal route and their photocatalytic activity was checked against methylene blue (MB) taken as a model dye. FTIR, XPS, BET, PL, XRD, TEM, and UV-Vis spectroscopy were used for the identification and morphological characterization of the prepared nanoparticles (NPs) and nanocomposites (NCs). The 7% Mg@ZnFe2O4 NPs demonstrated excellent degradation against MB under sunlight. The 7% Mg@ZnFe2O4 NPs were integrated with diverse contents (10, 50, 30, and 70 wt.%) of S@g-C3N4 to develop NCs with better activity. When the NCs were tested to degrade MB dye, it was revealed that the 7%Mg@ZnFe2O4/S@g-C3N4 NCs were more effective at utilizing solar energy than the other NPs and NCs. The synergistic effect of the interface formed between Mg@ZnFe2O4 and S@g-C3N4 was primarily responsible for the boosted photocatalytic capability of the NCs. The fabricated NCs may function as an effective new photocatalyst to remove organic dyes from wastewater.

Green synthesis of tellurium-doped SnO2 nanoparticles with sulfurized g-C3 N4 : Insights into methylene blue photodegradation and antibacterial capability.

The construction of SnO2 nanoparticles (NPs), specifically Te-doped SnO2 NPs, using a simple and economical co-precipitation technique has been thoroughly described in this work. NH3 served as the reducing agent in this procedure, whilst polyethylene glycol served as the capping agent. The primary goals of our work were to investigate the physicochemical properties of the synthesized SnO2 NPs and assess their potential use as antibacterial agents and photocatalysts. Scanning electron microscopy-energy dispersive X-ray, ultraviolet light, Fourier transform infrared spectroscopy, X-ray diffraction (XRD), and other analytical techniques were used to thoroughly analyze the NPs. Based on the full width at half maximum of the most noticeable peaks in the XRD spectrum, the Debye-Scherrer equation was used to calculate the crystallite sizes, which indicated the presence of a single tetragonal SnO2 phase. Particularly noteworthy was the exceptional photocatalytic activity of graphene-assisted Te-doped SnO2 NPs, achieving an impressive decomposition efficiency of up to 98% in the photo-oxidation of methylene blue. Furthermore, our investigation delved into the antibacterial attributes of the synthesized SnO2 NPs against Escherichia coli and Staphylococcus aureus, demonstrating inhibitory effects on both bacteria strains. This suggests potential applications for these NPs in various environmental and medical contexts.

Structural and Electronic (Absorption and Fluorescence) Properties of a Stable Triplet Diphenylcarbene: A DFT Study.

A triplet diphenylcarbene, bis[3-bromo-5-(trifluoromethyl)[1,1'-biphenyl]-4-yl]methylidene (B3B), with exceptional stability was discovered by chemists from Japan's Mie University. To investigate its different quantum chemical features, a theoretical analysis was predicated on Density Functional Theory (DFT) and Time Dependent-DFT (TD-DFT) based technique. According to the findings, the singlet-triplet energy gap (ES-T), as well as HOMO-LUMO energy bandgap (EH-L), was found to be diminished when nucleophilicity (N) rose. We looked at the geometrical dimensions, molecular orbitals (MOs), electronic spectra, electrostatic potential, molecular surfaces, reactivity characteristics, and thermodynamics features of the title carbene (B3B). Its electronic spectra in different solvents were calculated using TD-DFT and Polarizable Continuum Model (PCM) framework. The estimated absorption maxima of B3B were seen between 327 and 340 nm, relying on the solvents, and were attributed to the S0 → S1 transition. Estimated fluorescence spectral peaks were found around 389 and 407 nm with the S1 and S0 transitions being identified. Its fluorescence/absorption intensities revealed a blue shift change when the solvent polarity was increased. The least exciting state has been discovered to be the π → π* charge-transfer (CT) phase. According to the Natural Bonding Orbital (NBO) exploration, ICT offers a significant role in chemical system destabilization. Furthermore, several hybrid features were used to determine the NLO (nonlinear optical) features (polarizability, first-order hyperpolarizability, and dipole moment). The calculated values suggest that B3B is a promising candidate for further research into nonlinear optical properties.

Fabrication of Cr-ZnFe2O4/S-g-C3N4 Heterojunction Enriched Charge Separation for Sunlight Responsive Photocatalytic Performance and Antibacterial Study.

There has been a lot of interest in the manufacture of stable, high-efficiency photocatalysts. In this study, initially Cr doped ZnFe2O4 nanoparticles (NPs) were made via surfactant-assisted hydrothermal technique. Then Cr-ZnFe2O4 NPs were modified by incorporating S-g-C3N4 to enhance their photocatalytic efficiency. The morphological, structural, and bonding aspects were analyzed by XRD, FTIR, and SEM techniques. The photocatalytic efficiency of the functional Cr-ZnFe2O4/S-g-C3N4 (ZFG) heterostructure photocatalysts was examined against MB under sunlight. The produced ZFG-50 composite has the best photocatalytic performance, which is 2.4 and 3.5 times better than that of ZnFe2O4 and S-g-C3N4, respectively. Experiments revealed that the enhanced photocatalytic activity of the ZFG nanocomposite was caused by a more effective transfer and separation of photo-induced charges. The ZFG photocatalyst can use sunlight for treating polluted water, and the proposed modification of ZnFe2O4 using Cr and S-g-C3N4 is efficient, affordable, and environmentally benign. Under visible light, Gram-positive and Gram-negative bacteria were employed to ZFG-50 NCs' antimicrobial activity. These ZFG-50 NCs also exhibit excellent antibacterial potential.

Simultaneous Quantification of Opioids in Blood and Urine by Gas Chromatography-Mass Spectrometer with Modified Dispersive Solid-Phase Extraction Technique.

Common methodologies such as liquid-liquid extraction and solid-phase extraction are applied for the extraction of opioids from biological specimens i.e., blood and urine. Techniques including LC-MS/LC-MSMS, GC-MS, etc. are used for qualitative or quantitative determination of opioids. The goal of the present work is to design a green, economic, rugged, and simple extraction technique for famous opioids in human blood and urine and their simultaneous quantification by GC-MS equipped with an inert plus electron impact (EI) ionization source at SIM mode to produce reproducible and efficient results. Morphine, codeine, 6-acetylmorphine, nalbuphine, tramadol and dextromethorphan were selected as target opioids. Anhydrous Epsom salt was applied for dSPE of opioids from blood and urine into acetonitrile extraction solvent with the addition of sodium phosphate buffer (pH 6) and n-hexane was added to remove non-polar interfering species from samples. BSTFA was used as a derivatizing agent for GC-MS. Following method validation, the LOD/LLOQ and ULOQ were determined for morphine, codeine, nal-buphine, tramadol, and dextromethorphan at 10 ng/mL and 1500 ng/mL, respectively, while the LOD/LLOQ and ULOQ were determined for 6-acetylmorphine at 5 ng/mL and 150 ng/mL, respectively. This method was applied to real blood and urine samples of opioid abusers and the results were found to be reproducible with true quantification.

Integration of Mn-ZnFe2O4 with S-g-C3N4 for Boosting Spatial Charge Generation and Separation as an Efficient Photocatalyst.

The disposal of dyes and organic matter into water bodies has become a significant source of pollution, posing health risks to humans worldwide. With rising water demands and dwindling supplies, these harmful compounds must be isolated from wastewater and kept out of the aquatic environment. In the research presented here, hydrothermal synthesis of manganese-doped zinc ferrites' (Mn-ZnFe2O4) nanoparticles (NPs) and their nanocomposites (NCs) with sulfur-doped graphitic carbon nitride (Mn-ZnFe2O4/S-g-C3N4) are described. The samples' morphological, structural, and bonding features were investigated using SEM, XRD, and FTIR techniques. A two-phase photocatalytic degradation study of (0.5, 1, 3, 5, 7, 9, and 11 wt.%) Mn-doped ZnFe2O4 NPs and Mn-ZnFe2O4/(10, 30, 50, 60, and 70 wt.%) S-g-C3N4 NCs against MB was carried out to find the photocatalyst with maximum efficiency. The 9% Mn-ZnFe2O4 NPs and Mn-ZnFe2O4/50% S-g-C3N4 NCs exhibited the best photocatalyst efficiency in phase one and phased two, respectively. The enhanced photocatalytic activity of the Mn-ZnFe2O4/50% S-g-C3N4 NCs could be attributed to synergistic interactions at the Mn-ZnFe2O4/50% S-g-C3N4 NCs interface that resulted in a more effective transfer and separation of photo-induced charges. Therefore, it is efficient, affordable, and ecologically secure to modify ZnFe2O4 by doping with Mn and homogenizing with S-g-C3N4. As a result, our current research suggests that the synthetic ternary hybrid Mn-ZnFe2O4/50% S-g-C3N4 NCs may be an effective photocatalytic system for degrading organic pollutants from wastewater.

Cation Incorporation and Synergistic Effects on the Characteristics of Sulfur-Doped Manganese Ferrites S@Mn(Fe2O4) Nanoparticles for Boosted Sunlight-Driven Photocatalysis.

In the present work, sulfur-doped manganese ferrites S@Mn(Fe2O4) nanoparticles were prepared by using the sol-gel and citrate method. The concentration of sulfur varied from 1 to 7% by adding Na2S. The samples were characterized by performing Fourier Transformed Infrared Spectroscopy (FTIR), Energy Dispersive X-ray (EDX), X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and Ultraviolet-Visible spectroscopy (UV-Visible). The synthesized sulfur-doped manganese ferrites were applied to evaluate the photocatalytic degradation of the dyes. Further, the degradation studies revealed that the nanoparticles successfully degraded the methylene blue dye by adding a 0.006 g dose under the sunlight. The sulfur-doped manganese ferrite nanoparticles containing 3% sulfur completely degraded the dye in 2 h and 15 min in aqueous medium. Thus, the ferrite nanoparticles were found to be promising photocatalyst materials and could be employed for the degradation of other dyes in the future.

Improving the Thermal Behavior and Flame-Retardant Properties of Poly(o-anisidine)/MMT Nanocomposites Incorporated with Poly(o-anisidine) and Clay Nanofiller.

The synthesis of MMT and poly(o-anisidine) (MMT/POA) clay nanocomposites was carried out by using the chemical oxidative polymerization of POA and MMT clay with POA, respectively. By maintaining the constant concentration of POA, different percentage loads of MMT clay were used to determine the effect of MMT clay on the properties of POA. The interaction between POA and MMT clay was investigated by FTIR spectroscopy, and, to reveal the complete compactness and homogeneous distribution of MMT clay in POA, were assessed by using scanning-electron-microscope (SEM) analysis. The UV-visible spectrum was studied for the optical and absorbance properties of MMT/POA ceramic nanocomposites. Furthermore, the horizontal burning test (HBT) demonstrated that clay nanofillers inhibit POA combustion.

TAEO-A Thermal Aware & Energy Optimized Routing Protocol for Wireless Body Area Networks.

Wireless Body Area Networks (WBANs) are in the spotlight of researchers and engineering industries due to many applications. Remote health monitoring for general as well as military purposes where tiny sensors are attached or implanted inside the skin of the body to sense the required attribute is particularly prominent. To seamlessly accomplish this procedure, there are various challenges, out of which temperature control to reduce thermal effects and optimum power consumption to reduce energy wastage are placed at the highest priority. Regular and consistent operation of a sensor node for a long-time result in a rising of the temperature of respective tissues, where it is attached or implanted. This temperature rise has harmful effects on human tissues, which may lead to the tissue damage. In this paper, a Temperate Aware and Energy Optimized (TAEO) routing protocol is proposed that not only deals with the thermal aspects and hot spot problem, but also extends the stability and lifetime of a network. Analytical simulations are conducted, and the results depict better performance in terms of the network lifetime, throughput, energy preservation, and temperature control with respect to state of the art WBAN protocols.

Coagulation-flocculation for lignin removal from wastewater - a review.

Industrial discharge has tremendously increased inorganic pollutants in water bodies all over the world. Paper and pulp effluent is included in one of the most pollution generating discharges containing complex chemical compounds such as lignin. For clean and healthy water resources, the recovery of lignin from wastewater from the paper and pulp industry is of high importance. Available chemical and biological technologies for removal of lignin have certain drawbacks. Coagulation and flocculation is not only the economic but also the effective method for removal of lignin. The present review highlights available coagulants employed for removal of lignin from paper and pulp wastewater. Each coagulant is pH dependent and shows varied results with change in effluent characteristics. The hydrolysis products of aluminium-based coagulants, iron-based coagulants and copper sulphate have positive charges. These positive charges promote formation of flocs through charged neutralisation or sweep flocculation. In the case of titanium-based coagulants, hydrolysis product is negatively charged and mode is heterocoagulation. Ninety percent recovery of lignin is achieved by using a mixture of oxotitanium sulphate and aluminium sulphate and 80% with aluminium sulphate. Virtually complete recovery of lignin is observed with oxotitanium sulphate.

Nanostructured Design Cathode Materials for Magnesium-Ion Batteries.

Energy is undeniably one of the most fundamental requirements of the current generation. Solar and wind energy are sustainable and renewable energy sources; however, their unpredictability points to the development of energy storage systems (ESSs). There has been a substantial increase in the use of batteries, particularly lithium-ion batteries (LIBs), as ESSs. However, low rate capability and degradation due to electric load in long-range electric vehicles are pushing LIBs to their limits. As alternative ESSs, magnesium-ion batteries (MIBs) possess promising properties and advantages. Cathode materials play a crucial role in MIBs. In this regard, a variety of cathode materials, including Mn-based, Se-based, vanadium- and vanadium oxide-based, S-based, and Mg2+-containing cathodes, have been investigated by experimental and theoretical techniques. Results reveal that the discharge capacity, capacity retention, and cycle life of cathode materials need improvement. Nevertheless, maintaining the long-term stability of the electrode-electrolyte interface during high-voltage operation continues to be a hurdle in the execution of MIBs, despite the continuous research in this field. The current Review mainly focuses on the most recent nanostructured-design cathode materials in an attempt to draw attention to MIBs and promote the investigation of suitable cathode materials for this promising energy storage device.

Tailoring of an anti-diabetic drug empagliflozin onto zinc oxide nanoparticles: characterization and in vitro evaluation of anti-hyperglycemic potential.

Diabetes is a serious health issue that can be a great risk factor related to numerous physical problems. A class of drugs "Gliflozin" especially Sodium Glucose Co. Transporter 2 was inhibited by a novel drug, which is known as "empagliflozin". While ZnO nanoparticles (NPs) had considerable promise for combating diabetes, it was employed in the treatment and management of type-2 diabetes mellitus. The new drug empagliflozin was initially incorporated into Zinc Oxide NPs in this study using the surface physio-sorption technique, and the degree of drug adsorption was assessed using the HPLC method. The tailored product was characterized by using the FTIR, EDX, Ultraviolet-Visible, XRD and SEM techniques. With an average particle size of 17 nm, SEM revealed mono-dispersion of NPs and sphere-like form. The Freundlich isotherm model best fits and explains the data for the physio-sorption investigation, which examined adsorption capabilities using adsorption isotherms. The enzymes α-amylase and α-glucosidase, which are involved in the human metabolism of carbohydrates, were used in the in-vitro anti-diabetic assays. It was discovered that the composite showed the highest levels of 81.72 and 92.77% inhibition of -α-amylase and -glucosidase at an absolute concentration of 1000 µg per ml with IC50 values of 30.6 µg per ml and 72 µg per ml.

One-pot synthesis of redox-responsive polymers-coated mesoporous silica nanoparticles and their controlled drug release.

A versatile one-pot strategy for the preparation of reversibly cross-linked polymer-coated mesoporous silica nanoparticles (MSNs) via surface reversible addition-fragmentation chain transfer (RAFT) polymerization is presented for the first time in this paper. The less reactive monomer oligo(ethylene glycol) acrylate (OEGA) and the more reactive cross-linker N,N'-cystaminebismethacrylamide (CBMA) are chosen to be copolymerized on the external surfaces of RAFT agent-functionalized MSNs to form the cross-linked polymer shells. Owing to the reversible cleavage and restoration of disulfide bonds via reduction/oxidation reactions, the polymer shells can control the on/off switching of the nanopores and regulate the drug loading and release. The redox-responsive release of doxorubicin (DOX) from this drug carrier is realized. The protein adsorption, in vitro cytotoxicity assays, and endocytosis studies demonstrate that this biocompatible vehicle is a potential candidate for delivering drugs. It is expected that this versatile grafting strategy may help fabricate satisfying MSN-based drug delivery systems for clinical application.

Synthesis and applications of graphitic carbon nitride (g-C3N4) based membranes for wastewater treatment: A critical review.

Semiconducting membrane combined with nanomaterials is an auspicious combination that may successfully eliminate diverse waste products from water while consuming little energy and reducing pollution. Creating an inexpensive, steady, flexible, and diversified business material for membrane production is a critical challenge in membrane technology development. Because of its unusual structure and high catalytic activity, graphitic carbon nitride (g-C3N4) has come out as a viable material for membranes. Furthermore, their great durability, high permanency under challenging environments, and long-term use without decrease in flux are significant advantages. The advanced material techniques used to manage the molecular assembly of g-C3N4 for separation membrane were detailed in this review work. The progress in using g-C3N4-based membranes for water treatment has been detailed in this presentation. The review delivers an updated description of g-C3N4 based membranes and their separation functions and new ideas for future enhancements/adjustments to address their weaknesses in real-world situations. Finally, the ongoing problems and promising future research directions for g-C3N4-based membranes are discussed.

Sustainable appraisal of lac (Kerria Lacca) based anthraquinone natural dye for chemical and bio-mordanted viscose and silk dyeing.

The coloring behavior of laccaic acid, a natural red dye derived from lac insects, has been investigated in this work for the dyeing of silk and viscose fabrics while being heated in MW radiation. The extract was made in an aqueous and acidic media and then used to color fabrics under microwave treatment for up to 10 min. For developing new shades, eco-friendly green bio-mordants and, in comparison, chemical mordants were employed at given conditions. The obtained results revealed that the aqueous extract after 4 min of radiation exposure produced a high color strength (K/S = 17.132) onto silk and the aqueous extract after 6 min of radiation exposure produced better color strength (K/S = 6.542) onto viscose at selected conditions. The fastness ratings evaluation as per ISO standards demonstrates that bio-anchors have provided good ratings under selected irradiation and dyeing conditions. It is concluded that this environmentally friendly technique has improved the natural coloration process of fabrics as well as addition of green mordants has furnished colorfast shades using lac-derived natural anthraquinone dye.

Carbon Nanotube Fiber-Based Flexible Microelectrode for Electrochemical Glucose Sensors.

Electrochemical sensors are gaining significant demand for real-time monitoring of health-related parameters such as temperature, heart rate, and blood glucose level. A fiber-like microelectrode composed of copper oxide-modified carbon nanotubes (CuO@CNTFs) has been developed as a flexible and wearable glucose sensor with remarkable catalytic activity. The unidimensional structure of CNT fibers displayed efficient conductivity with enhanced mechanical strength, which makes these fibers far superior as compared to other fibrous-like materials. Copper oxide (CuO) nanoparticles were deposited over the surface of CNT fibers by a binder-free facile electrodeposition approach followed by thermal treatment that enhanced the performance of non-enzymatic glucose sensors. Scanning electron microscopy and energy-dispersive X-ray analysis confirmed the successful deposition of CuO nanoparticles over the fiber surface. Amperometric and voltammetric studies of fiber-based microelectrodes (CuO@CNTFs) toward glucose sensing showed an excellent sensitivity of ∼3000 µA/mM cm2, a low detection limit of 1.4 µM, and a wide linear range of up to 13 mM. The superior performance of the microelectrode is attributed to the synergistic effect of the electrocatalytic activity of CuO nanoparticles and the excellent conductivity of CNT fibers. A lower charge transfer resistance value obtained via electrochemical impedance spectroscopy (EIS) also demonstrated the superior electrode performance. This work demonstrates a facile approach for developing CNT fiber-based microelectrodes as a promising solution for flexible and disposable non-enzymatic glucose sensors.

A highly explicit electrochemical biosensor for catechol detection in real samples based on copper-polypyrrole.

Catechol is a pollutant that can lead to serious health issues. Identification in aquatic environments is difficult. A highly specific, selective, and sensitive electrochemical biosensor based on a copper-polypyrrole composite and a glassy carbon electrode has been created for catechol detection. The novelty of this newly developed biosensor was tested using electrochemical techniques. The charge and mass transfer functions and partially reversible oxidation kinetics of catechol on the redesigned electrode surface were examined using electrochemical impedance spectroscopy and cyclic voltammetry scan rates. Using cyclic voltammetry, chronoamperometry, and differential pulse voltammetry, the characteristics of sensitivity (8.5699 µA cm-2), LOD (1.52 × 10-7 µM), LOQ (3.52 × 10-5 µM), linear range (0.02-2500 µM), specificity, interference, and real sample detection were investigated. The morphological, structural, and bonding characteristics were investigated using XRD, Raman, FTIR, and SEM. Using an oxidation-reduction technique, a suitable biosensor material was produced. In the presence of interfering compounds, it was shown that it was selective for catechol, like an enzyme.

Source, occurrence, distribution, fate, and implications of microplastic pollutants in freshwater on environment: A critical review and way forward.

The generation of microplastics (MPs) has increased recently and become an emerging issue globally. Due to their long-term durability and capability of traveling between different habitats in air, water, and soil, MPs presence in freshwater ecosystem threatens the environment with respect to its quality, biotic life, and sustainability. Although many previous works have been undertaken on the MPs pollution in the marine system recently, none of the study has covered the scope of MPs pollution in the freshwater. To consolidate scattered knowledge in the literature body into one place, this work identifies the sources, fate, occurrence, transport pathways, and distribution of MPs pollution in the aquatic system with respect to their impacts on biotic life, degradation, and detection techniques. This article also discusses the environmental implications of MPs pollution in the freshwater ecosystems. Certain techniques for identifying MPs and their limitations in applications are presented. Through a literature survey of over 276 published articles (2000-2023), this study presents an overview of solutions to the MP pollution, while identifying research gaps in the body of knowledge for further work. It is conclusive from this review that the MPs exist in the freshwater due to an improper littering of plastic waste and its degradation into smaller particles. Approximately 15-51 trillion MP particles have accumulated in the oceans with their weight ranging between 93,000 and 236,000 metric ton (Mt), while about 19-23 Mt of plastic waste was released into rivers in 2016, which was projected to increase up to 53 Mt by 2030. A subsequent degradation of MPs in the aquatic environment results in the generation of NPs with size ranging from 1 to 1000 nm. It is expected that this work facilitates stakeholders to understand the multi-aspects of MPs pollution in the freshwater and recommends policy actions to implement sustainable solutions to this environmental problem.

Synchronized electrochemical detection of hydroquinone and catechol in real water samples using a Co@SnO2-polyaniline composite.

The conductive composite Co@SnO2-PANI was successfully synthesized using hydrothermal/oxidative synthesis. Using differential pulse voltammetry, a glassy carbon electrode modified with a CoSnO2-PANI (polyaniline)-based electrochemical biosensor has been created for the quick detection of two phenolics, hydroquinone (Hq) and catechol (Cat). Differential pulse voltammetry (DPV) measurements revealed two well-resolved, strong peaks for GCE@Co-SnO2-PANI, which corresponded to the oxidation of Hq and Cat at 275.87 mV and +373.76 mV, respectively. The oxidation peaks of Hq and Cat mixtures were defined and separated at a pH of 8.5. High conductivity and remarkable selectivity reproducibility was tested by electrochemical impedance spectroscopy, chronoamperometry, and cyclic voltammetry techniques in standard solution and real water samples. The proposed biosensor displayed a low detection limit of 4.94 nM (Hq) and 1.5786 nM (Cat), as well as a large linear range stretching from 2 × 10-2 M to 2 × 10-1 M. The real-sample testing showed a good recovery for the immediate detection of Hq (96.4% recovery) and Cat (98.8% recovery) using the investigated sensing apparatus. The synthesized biosensor was characterized by XRD, FTIR, energy dispersive spectroscopy and scanning electron microscopy.