Methodologies for the analytical determination of ferrate(VI): a review.

This paper reviewed different analytical techniques to determine concentrations of the environmentally-friendly oxidant ferrate(VI) (Fe(VI)O(2-)(4), Fe(VI)) anion in solid and solution samples. The techniques included volumetric (chromite and arsenite), electrochemical (cyclic voltammetry and potentiometry), and spectrophotometric methods (Fourier transform infrared, Mossbauer, UV-Visible, 2,2-azino-bis(3-ethylbenzothiazoline-6-sulfonate (ABTS), and fluorescence). The importance of the techniques were briefly described. This paper also presented a newly developed method for the determination of low concentrations (0.25 µM) of Fe(VI)) using the reaction between Fe(VI) and iodide (I(-)), which formed the yellowish color of I(-)(3) that could be measured spectrophotometrically at 351 nm. The increase in I(-)(3) was linear with respect to Fe(VI) added (0.25-76 µM) in buffered solutions at pH 5.5-9.3. The linearity was not affected by the ions present in tap water.

Matrix Metalloproteinase-3 induces proteoglycan degradation in gouty arthritis model.

BACKGROUND: Gout is an inflammatory arthritis resulting from precipitation of monosodium urate (MSU) crystals in joints and surrounding tissues. However, the mechanism underlying high levels of uric acid inducing gouty arthritis has not been clarified. OBJECTIVE: The purpose was to investigate the role of Matrix Metalloproteinase-3 (MMP-3) in the development of gouty arthritis from hyperuricemia. METHOD: MSU crystal-induced gouty arthritis model and chondrocytes were used to evaluate changes of MMP-3 levels. Western blot, qPCR and ELISA were performed to detect MMP-3, Tissue Inhibitors of Metalloproteinase-1 (TIMP-1) and A Disintegrin and Metalloproteinase with Thrombospondin Motifs-4 (ADAMTS-4) expressions in rabbit chondrocytes. Expression of proteoglycan was determined through toluidine blue staining. Concentrations of glycosaminoglycan, Interleukin-6 (IL-6), Interleukin-1ß (IL-1ß) and Tumor Necrosis Factor-α (TNF-α) in chondrocytes were assessed via ELISA kits. Concentration of uric acid in supernate was tested by Automatic Analyzer. RESULTS: MMP-3 was significantly increased in rat serum, synovial fluid, cartilages and chondrocytes treated with high-level uric acid. Increased concentration of glycosaminoglycancould be observed in chondrocytes incubated with MMP-3, as well as the remarkable downregulation of proteoglycan expression. Furthermore, high-level uric acid contributed to the degradation of proteoglycan via the activation of MMP-3. IL-6, IL-1ß and TNF-α concentrations were increased significantly in 35 °C compared to 37 °C with MMP-3 and high-level uric acid. CONCLUSION: Our study showed that MMP-3 was enhanced by high levels of uric acid, which promoted proteoglycan degradation, and induced MSU crystallization in turn. A low temperature environment is an important factor in the development of gout.

The Role of Autophagy in the Innate Immune Response to Fungal Keratitis Caused by Aspergillus fumigatus Infection.

Purpose: To determine the role of autophagy in the innate immune response to fungal keratitis (FK) caused by Aspergillus fumigatus infection. Methods: Corneal samples obtained from patients and mice with FK were visualized via transmission electron microscopy (TEM). Autophagy-related proteins LC3B-II, Beclin-1, LAMP-1, and p62 in A. fumigatus-infected corneas of C57BL/6 mice were tested by Western blot. After treatment with autophagy inhibitors 3-methyladenine (3-MA), chloroquine (CQ), or inducer rapamycin, autophagy-related proteins were detected by Western blot. Corneas were photographed with slit lamp microscopy and pathological changes were observed by hematoxylin and eosin staining. Polymorphonuclear neutrophilic leukocytes (PMNs) were assessed by immunofluorescent staining and observed under TEM. The levels of CXCL-1, IL-1ß, HMGB1, IL-18, TNF-α, and IL-10 were tested by reverse transcription polymerase chain reaction and Western blot. The quantification of fungal loads was detected and photographed. Results: The accumulation of autophagosomes in corneas of patients and mice with FK was observed with TEM. The expression of LC3B-II, Beclin-1, and LAMP-1 was elevated in corneas after fungal infection, whereas p62 was reduced. Treatment with 3-MA or CQ upregulated clinical scores, pathological changes, and the expression of CXCL-1, IL-1ß, HMGB1, IL-18, and TNF-α except IL-10. The morphology of PMNs was changed and PMN recruitment was increased in mice corneas treated with 3-MA or CQ, whereas rapamycin reduced the inflammatory response to keratitis. These results were statistically significant. Conclusions: A. fumigatus infection increases the expression of autophagy in corneas. Autophagy plays an anti-inflammatory role in the innate immune response to A. fumigatus keratitis.

High-mobility group box1 as an amplifier of immune response and target for treatment in Aspergillus fumigatus keratitis.

AIM: To determine the roles of high-mobility group box1 (HMGB1) in pro-inflammation, host immune response and its potential target for treatment in Aspergillus fumigatus (A.fumigatus) keratitis. METHODS: Expression of HMGB1 was tested in C57BL/6 normal and infected corneas. Dual immunostaining tested co-expression of HMGB1 with TLR4 or LOX-1. C57BL/6 mice were pretreated with Box A or PBS and then infected. Clinical scores, polymerase chain reaction, ELISA, and MPO assay were used to assess the disease response. Flow cytometry were used to test the effect of Box A on reactive oxygen species (ROS) expression after A.fumigatus stimulation in polymorphonuclear neutrophilic leukocytes (PMN). C57BL/6 peritoneal macrophages were pretreated with Box B before A.fumigatus stimulation, and MIP-2, IL-1ß, TNF-α, HMGB1 and LOX-1 were measured. Macrophages were pretreated with Box B or Box B combined with Poly(I) (an inhibitor of LOX-1) before stimulating with A.fumigatus, and MIP-2, IL-1ß, TNF-α, LOX-1, p38-MAPK, p-p38-MAPK were measured. RESULTS: HMGB1 levels were elevated in C57BL/6 mice after infection. HMGB1 co-expressed with TLR4, and LOX-1 in infiltrated cells. Box A vs PBS treated C57BL/6 mice had lower clinical scores and down-regulated corneal HMGB1, MIP-2, IL-1ß expression and neutrophil influx. Box B treatment amplified expression of MIP-2, IL-1ß, TNF-α, HMGB1 and LOX-1 that induced by A.fumigatus in macrophage. Compared to the treatment of Box B only, the protein expression of IL-1ß, TNF-α showed inhibition of Box B combined with Poly(I), which also reduced the A.fumigatus-evoked protein level of LOX-1 and phosphorylation level of p38-MAPK. The production of A.fumigatus-stimulated ROS was significantly declined after Box A pretreatment in PMN. CONCLUSION: Blocking HMGB1 reduces the disease response in C57BL/6 mice. HMGB1 can amplify the host immune response through p38-MAPK, and is a target for treatment of A.fumigatus keratitis.

Screening analysis of volatile organic contaminants in commercial inorganic coagulants used for drinking water treatment.

A method for quality screening is suggested to detect volatile impurities in inorganic coagulants that are used for drinking water treatment. Static headspace gas chromatography with mass spectrometry detection (HS-GCMS) is sensitive and selective to detect volatiles in low concentrations. This study has discovered that volatile organic impurities are detectable in ferric and aluminium-based coagulants which are used for drinking water treatment. For ferric chloride, 2-propanol was detected at a level of 17-24 microg ml(-1), acetone at 0.7-1.7 microg ml(-1), 1,1,1-trichloroacetone at 0.02-0.04 microg ml(-1), trichloromethane at 0.01-0.02 microg ml(-1) and toluene at 0.01-0.12 microg ml(-1). For ferric chloride sulfate, acetone was detected at a level of 0.12 microg ml(-1), 1,1,1-trichloroacetone at 0.06-0.08 microg ml(-1), trichloromethane at 0.13-0.23 microg ml(-1), bromodichloromethane at 0.04-0.06 microg ml(-1) and dibromochloromethane at 0.04-0.05 microg ml(-1). For aluminium hydroxide chloride, only trichloromethane was detectable, but below the method detection limits (MDL). Although the concentrations of these impurities in commercial coagulants are low, this observation is important and should have impact on water industries for them to pay attention to the chemicals they are using for drinking water production.

Inhibition of LOX-1 alleviates the proinflammatory effects of high-mobility group box 1 in Aspergillus fumigatus keratitis.

AIM: To investigate the inflammatory amplification effect of high-mobility group box 1 (HMGB1) in Aspergillus fumigatus (A. fumigatus) keratitis and the relationship between lectin-like oxidized low-density lipoprotein receptor 1 (LOX-1) and HMGB1 in keratitis immune responses. METHODS: Phosphate buffer saline (PBS), and Boxb were injected into BALB/c mice subconjunctivally before the corneas were infected with A. fumigatus. RAW264.7 macrophages and neutrophils were pretreated with PBS and Boxb to determine the HMGB1 inflammatory amplification effects. Abdominal cavity extracted macrophages were pretreated with Boxb and Poly (I) (a LOX-1 inhibitor) before A. fumigatus hyphae stimulation to prove the the relationship between the two molecules. LOX-1, interleukin-1ß (IL-1ß), tumor necrosis factor-α (TNF-α), macrophage inflammatory protein-2 (MIP-2) and IL-10 were assessed by polymerase chain reaction and Western blot. RESULTS: Pretreatment with Boxb exacerbated corneal inflammation. In macrophages and neutrophils, A. fumigatus induced LOX-1, IL-1ß, TNF-α and MIP-2 expression in Boxb group was higher than those in PBS group. Poly (I) treatments before infection alleviated the proinflammatory effects of Boxb in abdominal cavity extracted macrophages. Pretreatment with Boxb did not influence Dectin-1 mRNA levels in macrophages and neutrophils. CONCLUSION: In fungal keratitis, HMGB1 is a proinflammatory factor in the first line of immune response. HMGB1 mainly stimulates neutrophils and macrophages to produce inflammatory cytokines and chemokines during the immune response. LOX-1 participates in HMGB1 induced inflammatory exacerbation in A. fumigatus keratitis.

Disparate expression of autophagy in corneas of C57BL/6 mice and BALB/c mice after Aspergillus fumigatus infection.

AIM: To determine the disparate expression of autophagy in the Aspergillus fumigatus (A. fumigatus) keratitis between susceptible C57BL/6 mice and resistant BALB/c mice. METHODS: C57BL/6 and BALB/c mice were used to establish fungal keratitis models. Disease severity and inflammatory response were observed by slit lamp microscopy in A. fumigatus-infected corneas of C57BL/6 and BALB/c mice at 1, 3 and 5d. Hematoxylin-eosin (H&E) staining was used to detect pathological changes of corneas. The expression of autophagy-related proteins Beclin-1, LC3, SQSTM1/p62, and LAMP-1 was assessed by Western blot in C57BL/6 and BALB/c mice at 1, 3 and 5d post infection (p.i.). Immunofluorescent staining was used to test the expression of LC3 in corneas after A. fumigatus infection. RESULTS: Keratitis severity was higher in C57BL/6 mice versus BALB/c mice at 1, 3 and 5d p.i. H&E staining showed that the number of inflammatory cells was larger and the severity of ulcer was higher in C57BL/6 mice than in BALB/c mice after stimulation with A. fumigatus. Higher expression of LAMP-1, Beclin-1, and LC3 was shown in C57BL/6 mice corneas than in BALB/c mice corneas at 1, 3 and 5d p.i., while the expression of p62 was lower in C57BL/6 mice. The fluorescence of LC3 was significantly increased in corneas of C57BL/6 mice compared with BALB/c mice after A. fumigatus infection. CONCLUSION: The expression of autophagy is higher in corneas of C57BL/6 mice than in BALB/c mice after A. fumigatus infection. Autophagy may be positively correlated with keratitis severity and pathological changes.

Formation of oxidation by-products of the iodinated X-ray contrast medium iomeprol during ozonation.

The present work describes the investigation of the formation of oxidation by-products of the iodinated X-ray contrast medium (ICM) iomeprol during ozonation in water treatment. Bench-scale investigations revealed that ICM can be partly oxidized during ozonation processes, whereas the ionic diatrizoic acid showed the lowest reactivity. Iomeprol, as a representative of ICM, was not fully mineralized during ozonation. Thus, unknown oxidation by-products were formed. Aqueous solutions of iomeprol were treated by ozonation in order to assess the formation of oxidation by-products. The by-products were characterized by different liquid chromatography methods including detection of single-stage mass spectra, product ion mass spectra, and induced in-source fragmentation for analysis of iodine containing oxidation by-products. Aldehyde and carbonyl containing compounds were proposed to be among the stable by-products. A derivatization step confirms that the aldehyde and carbonyl moieties are major functional groups in oxidation by-products of iomeprol. Furthermore, oxidation by-products of iomeprol were detected at the outlet of an ozone reactor at a full-scale waterworks. However, the toxicological relevance of the by-products is a major future research tasks.

The exploration of potassium ferrate(VI) as a disinfectant/coagulant in water and wastewater treatment.

This paper aims to explore potassium ferrate(VI) (K2FeO4) as an alternative water treatment chemical for both drinking water and wastewater treatment. The performance of potassium ferrate(VI) was evaluated in comparison with that of sodium hypochlorite (NaOCl) and that of NaOCl plus ferric sulphate (FS) or alum (AS). The dosages of ferrate(VI), NaOCl and FS/AS and sample pH values were varied in order to investigate the effects of these factors on the treatment performance. The study demonstrates that in drinking water treatment, ferrate(VI) can remove 10-20% more UV(254)-abs and DOC than FS for the same dose compared for natural pH range (6 and 8). The THMFP was reduced to less than 100 microg l(-1) by ferrate(VI) at a low dose. In addition to this, ferrate(VI) can achieve the disinfection targets (>6 log10 inactivation of Escherichia coliform (E. coli)) at a very low dose (6 mg l(-1) as Fe) and over wide working pH in comparison with chlorination (10 mg l(-1) as Cl2) plus coagulation (FS, 4 mg l(-1) as Fe). In wastewater treatment, ferrate(VI) can reduce 30% more COD, and kill 3log10 more bacteria compared to AS and FS at a similar or even smaller dose. Also, potassium ferrate(VI) can produce less sludge volume and remove more pollutants, which could make sludge treatment easier.

Monitoring of iodinated X-ray contrast media in surface water.

A monitoring programme was carried out in order to determine iodinated X-ray contrast media (ICM) in the River Danube and to investigate the raw water quality for drinking water production at Langenau waterworks. The study revealed that the maximum concentrations of ICM (over 500 ng l(-1) for diatrizoic acid and iopamidol) were found in 2h-composite samples taken from the downstream of the Ulm/Neu-Ulm metropolitan area. By means of a concentration profile over one month the highest ICM concentrations were observed on weekdays. The extended data evaluation with principal component analysis shows that the upstream and downstream samples had different pattern of variations in ICM concentration and also demonstrates a clear change in ICM composition by the discharge of municipal wastewater. In addition to load profiles of ICM, time-dependent plots of principal component 1 exhibited peaks, indicating a short-term discharge of ICM between the two sampling sites. In conclusion, a point source for ICM contamination between the sampling sites in Ulm upstream and Leipheim downstream seems to be the reasonable explanation for peak ICM concentrations. Due to the observed high variations of ICM concentrations in river, the evaluation of natural waters by means of a single analysis is not representative.

Reaction kinetics and oxidation product formation in the degradation of acetaminophen by ferrate (VI).

This paper investigates the degradation of acetaminophen (AAP) in aqueous solutions by ferrate (VI), aiming to propose the kinetics, pathways and the oxidation products' formation in the AAP degradation. A series of jar tests were undertaken over ferrate (VI) dosages (molar ratios of ferrate (VI):AAP, 5:1 to 25:1) and pH values (4-11). The effects of co-existing ions (0.2-5 mM) and humic acid (10-50 mg l(-1)) on the AAP removal were investigated. Ferrate (VI) can remove 99.6% AAP (from 1000 µg l(-1)) in 60 min under study conditions when majority of the AAP reduction occurred in the first 5 min. The treatment performance depended on the ferrate(VI) dosage, pH and the type and strength of co-existing ions and humic acid. Raising ferrate (VI) dosage with optimal pH 7 improved the AAP degradation. In the presence of humic acid, the AAP degradation by ferrate (VI) was promoted in a short period (<30 min) but then inhibited with increasing in humic acid contents. The presence of Al(3+), CO3(2-) and PO4(3-) ions declined but the existence of K(+), Na(+), Mg(2+) and Ca(2+) ions can improve the AAP removal. The catalytic function of Al(3+) on the decomposition of ferrate (VI) in aqueous solution was found. The kinetics of the reaction between ferrate (VI) and AAP was pseudo first-order for ferrete (VI) and pseudo second-order for AAP. The pseudo rate constant of ferrate (VI) with AAP was 1.4 × 10(-5) L(2) mg(-2) min(-1). Three oxidation products (OPs) were identified and the AAP degradation pathways were proposed.

Treatment of selected pharmaceuticals by ferrate(VI): performance, kinetic studies and identification of oxidation products.

The performance of ferrate(VI) in treating sulfamethoxazole (SMX), diclofenac (DCF), carbamazepine (CBZ) and bezafibrate (BZF) in test solutions containing the four compounds was investigated. A series of jar-test experiments was performed on a bench-scale at pH 6-9 and at a ferrate(VI) dose of 1-5 mg Fe/L. The results suggested that ferrate(VI) can effectively remove SMX, DCF and CBZ from the test solutions, with greater than 80% removal under optimum conditions. However, the removal efficiency of BZF was very low, less than 25% under the studied conditions. Increasing the dose of ferrate(VI) improved the treatment performance, while the influence of solution pH on ferrate(VI) performance varied among the different target compounds. Ferrate(VI) demonstrated the highest reactivity with SMX at pH 8 and pH 9 (20 °C), with apparent second-order rate constants of 360±17 M(-1) s(-1) and 1.26±0.02 M(-1) s(-1), respectively. However, BZF showed the lowest removal by ferrate(VI) with the smallest rate constants (less than 0.5 M(-1) s(-1)) at pH 8 and pH 9. Furthermore, a number of oxidation products (OPs) of SMX, DCF and CBZ during ferrate(VI) oxidation were detected by liquid chromatography and mass spectrometry (LC-MS), and their degradation pathways were tentatively proposed. No OPs of BZF were detected during ferrate(VI) oxidation.

Reaction kinetics and oxidation products formation in the degradation of ciprofloxacin and ibuprofen by ferrate(VI).

The treatment of ciprofloxacin (CIP) and ibuprofen (IBU) in test solutions by ferrate(VI) was investigated in this study. A series of jar test was performed in bench-scale at pH 6-9 and ferrate(VI) dose of 1-5 mg L(-1). Results demonstrated that ferrate(VI) removed CIP from test solutions efficiently, with above 70% of reduction under study conditions. In contrary, the removal rates of IBU were very low, less than 25% in all conditions. Raising ferrate(VI) dose improved the treatment performance, while the influence of solution pH was not significant at pH 6-9 compared with that of ferrate(VI) dose. In addition, kinetic studies of ferrate(VI) with both compounds were carried out at pH 8 and pH 9 (20 °C). Ferrate(VI) had a much higher reactivity with CIP than IBU at pH 8 and pH 9, with CIP's apparent second-order rate constants of 113.7±6.3 M(-1) s(-1) and 64.1±1.0 M(-1) s(-1), respectively. The rate constants of ferrate(VI) with IBU were less than 0.2 M(-1) s(-1) at pH 8 and pH 9. Furthermore, seven oxidation products (OPs) were formed during CIP degradation by ferrate(VI). The attack on the piperazinyl ring of the CIP by ferrate(VI) appeared to lead to the cleavage or hydroxylation of the rings, and the attack on the quinolone moiety by ferrate(VI) might lead to the cleavage of the double bond at the six-member heterocyclic ring. No OPs of IBU were detected during ferrate(VI) oxidation due to very small part of IBU was degraded by ferrate(VI).

Protective effects of grape seed extract fractions with different degrees of polymerisation on blood glucose, lipids and hepatic oxidative stress in diabetic rats.

The purpose of this study was to evaluate the effect of grape seed procyanidin (GSPE) fractions with different degrees of polymerisation (DPs) on blood glucose, lipids and hepatic oxidative stress in diabetic rats. Diabetic rats received a daily oral supplement of GSPE with different DPs for 6 weeks. During this period, blood glucose, body weight and food intake were assessed weekly. At the end of the experiment, serum lipid and hepatic oxidative stress were assessed compared with those of rats that did not receive GSPE. GSPE significantly decreased blood glucose, serum lipids and hepatic oxidative stress. Moreover, these effects were significantly better in the groups administered the oligomeric rather than the polymeric forms. These results demonstrate that GSPE has a positive effect on diabetes in rats, and the oligomeric form of GSPE may be more protective than other forms.

Progress in the development and use of ferrate(VI) salt as an oxidant and coagulant for water and wastewater treatment.

This paper reviews the progress in preparing and using ferrate(VI) salt as an oxidant and coagulant for water and wastewater treatment. The literature revealed that due to its unique properties (viz. strong oxidizing potential and simultaneous generation of ferric coagulating species), ferrate(VI) salt can disinfect microorganisms, partially degrade and/or oxidise the organic and inorganic impurities, and remove suspended/colloidal particulate materials in a single dosing and mixing unit process. However, these findings have not yet lead to the full-scale application of ferrate(VI) in the water industry owing to difficulties associated with the relatively low yield of ferrate(VI), the instability of the chemical depending on its method of preparation, and the lack of adequate studies that have demonstrated its capabilities and advantages over existing water and wastewater treatment methods. Fundamental study is thus required to explore the new preparation methods focusing on increasing the production yield and product's stability and avoiding using hypochlorite or chlorine as the oxidant. Also, the application of ferrate(VI) in drinking water treatment has not been studied systematically and future work in this field is recommended.

Laboratory study of electro-coagulation-flotation for water treatment.

An electro-coagulation-flotation process has been developed for water treatment. This involved an electrolytic reactor with aluminium electrodes and a separation/flotation tank. The water to be treated passed through the reactor and was subjected to coagulation/flotation, by Al(III) ions dissolved from the electrodes, the resulting flocs floating after being captured by hydrogen gas bubbles generated at cathode surfaces. Apparent current efficiencies for Al dissolution as aqueous Al(III) species at pH 6.5 and 7.8 were greater than unity. This was due to additional reactions occurring in parallel with Al dissolution: oxygen reduction at anodes and cathodes, and hydrogen evolution at cathodes, resulting in net (i.e. oxidation + reduction) currents at both anodes and cathodes. The specific electrical energy consumption of the reactor for drinking water treatment was as low as 20 kWh (kg Al)(-1) for current densities of 10-20A m(-2). The water treatment performance of the electrocoagulation process was found to be superior to that of conventional coagulation with aluminium sulphate for treating a model-coloured water, with 20% more dissolved organic carbon (DOC) being removed for the same Al(III) dose. However, for a lowland surface water sample, the two processes achieved a similar performance for DOC and UV-absorbance removal. In addition, an up-flow electrocoagulator configuration performed better than a horizontal flow configuration, with both bipolar and monopolar electrodes.

Comparison of modified montmorillonite adsorbents. Part II: The effects of the type of raw clays and modification conditions on the adsorption performance.

This paper builds on the preceding researches to study the effects of the type of clays (montmorillonites K10, KSF) and modifying conditions on the structure and adsorption behavior of resulting clay adsorbents. The raw clays were modified by polymeric Al/Fe species, hexadecyl-trimethylammonium (HDTMA) surfactant and a complex of polymeric Al/Fe-HDTMA. X-ray diffraction spectra was applied to analyze the structure of the raw and modified clays. After modification, the basal spacing of the clays varied, depending on the types of raw clay and modification conditions. Copper and phenol were selected as adsorbates for evaluating the adsorption performance of various clays, which was affected significantly by the types of raw clay and modification conditions. In general the inorganic contaminant (e.g., Cu) tend to be adsorbed by the polymeric Al/Fe modified clay and the organic impurities (e.g., phenol) will be preferably captured by the surfactant modified clay; both due to the specific surface properties resulting from introducing the modifiers. The complex modified clays possessed the ability of adsorbing both inorganic and organic contaminants. In addition, the d 0 0 1 spacing of modified KSF was greater than that of K10; the adsorption performance with modified KSF was thus greater than that with the modified K10. Finally, the ratio of modifiers to the clay (metal:surfactant:clay) has been observed to affect the adsorption performance; the optimal conditions have been defined.

Evaluation of modified clay coagulant for sewage treatment.

The use of modified clays as coagulants for sewage treatment was investigated in this study. The raw clays were montmorillonites K10 and KSF, and were modified by polymeric Al or Fe and/or Al/Fe mixing polymeric species. The comparative performance of modified clays and aluminium sulphate and ferric sulphate were evaluated in terms of the removal of turbidity, suspended solids, UV(254)-abs, colour, and total and soluble CODs. The results demonstrated that after being modified with mixing polymeric Al/Fe species, two montmorillonite clays possess greater properties to remove the particles (as suspended solids) and organic pollutants (as COD and UV(254)-abs) from the sewage and to enhance the particle settling rate significantly.

Comparison of modified montmorillonite adsorbents. Part I: Preparation, characterization and phenol adsorption.

This study concerns with the development of modified montmorillonites as adsorbents for water treatment. Polymeric aluminium and iron intercalated forms of montmorillonites have been prepared in the absence and presence of an alkylammonium cationic surfactant (Hexdecyl-trimethyl-ammonium bromide, HDTMA). Montmorillonites intercalated with polymeric Al, Fe, Fe/Al (2:1 Fe to Al ratio in solution), possess large N2 Brunauer-Emmett-Teller (BET) surface areas. XRD data also shows trace amounts of illite and plagioclase within the clay materials. Montmorillonites intercalated with HDTMA, polymeric Fe/HDTMA, polymeric Al/HDTMA and polymeric Fe/Al/HDTMA (1:1 metal to surfactant molar ratio in solution) undergo some losses of N2 BET surface areas. Preliminary adsorption studies on phenol have shown that polymeric Al/HDTMA- and HDTMA-only-modified montmorillonites possess a good affinity for phenol, whereas the polymeric Al/Fe modified- and starting montmorillonites have little affinity for phenol adsorption.

The influence of pH on the degradation of phenol and chlorophenols by potassium ferrate.

This paper presents information concerning the influence of solution pH on the aqueous reaction between potassium ferrate and phenol and three chlorinated phenols: 4-chlorophenol (CP), 2,4-dichlorophenol (DCP), 2,4,6-trichlorophenol (TCP). The redox potential and aqueous stability of the ferrate ion, and the reactivity of dissociating compounds, are known to be pH dependent. Laboratory tests have been undertaken over a wide range of pH (5.8-11) and reactant concentrations (ferrate:compound molar ratios of 1:1 to 8:1). The reactivity of trichloroethylene was also investigated as a reference compound owing to its non-dissociating nature. The extent of compound degradation by ferrate was found to be highly pH dependent, and the optimal pH (maximum degradation) decreased in the order: phenol/CP, DCP, TCP; at the optimal pH the degree of degradation of these compounds was similar. The results indicate that for the group of phenol and chlorophenols studied, the presence of an increasing number of chlorine substituent atoms corresponds to an increasing reactivity of the undissociated compound, and a decreasing reactivity of the dissociated compound.