RESUMEN
Superhydrophobic surfaces are often seen as frictionless materials, on which water is highly mobile. Understanding the nature of friction for such water-repellent systems is central to further minimize resistance to motion and energy loss in applications. For slowly moving drops, contact-line friction has been generally considered dominant on slippery superhydrophobic surfaces. Here, we show that this general rule applies only at very low speed. Using a micropipette force sensor in an oscillating mode, we measure the friction of water drops approaching or even equaling zero contact-line friction. We evidence that dissipation then mainly stems from the viscous shearing of the air film (plastron) trapped under the liquid. Because this force is velocity dependent, it can become a serious drag on surfaces that look highly slippery from quasi-static tests. The plastron thickness is found to be the key parameter that enables the control of this special friction, which is useful information for designing the next generation of ultraslippery water-repellent coatings.
RESUMEN
A bio-inspired approach to fabricate robust superhydrophobic (SHB) surfaces with anisotropic properties replicated from a leek leaf is presented. The polydimethylsiloxane (PDMS) replica surfaces exhibit anisotropic wetting, anti-icing, and light scattering properties due to microgrooves replicated from leek leaves. Superhydrophobicity is achieved by a novel modified candle soot (CS) coating that mimics leek's epicuticular wax. The resulting surfaces show a contact angle (CA) difference of ≈30° in the directions perpendicular and parallel to the grooves, which is similar to the anisotropic properties of the original leek leaf. The coated replica is durable, withstanding cyclic bending tests (up to 10 000 cycles) and mechanical sand abrasion (up to 60 g of sand). The coated replica shows low ice adhesion (10 kPa) after the first cycle; and then, increases to ≈70 kPa after ten icing-shearing cycles; while, anisotropy in ice adhesion becomes more evident with more cycles. In addition, the candle soot-coated positive replica (CS-coated PR) demonstrates a transmittance of ≈73% and a haze of ≈65% at the wavelength of 550 nm. The results show that the properties depend on the replicated surface features of the leek leaf, which means that the leek leaf appears to be a highly useful template for bioinspired surfaces.
RESUMEN
When a droplet interacts with a water-repellent surface, its triple-phase contact line typically exhibits varying contact angles, which can vary from point-to-point across the surface. Consequently, measuring the contact angles along the contact line would provide a better representation of the wetting properties of the surface than a single average contact angle. However, an effective method for estimating the local contact angle along the contact line on opaque hydrophobic surfaces is currently lacking. Here we present a method that combines through-drop imaging of the wetting interface during a sliding experiment with Finite Element Modeling of the droplet to estimate contact angle values along the contact line. Using this method, the mean advancing and receding contact angles were measured on four types of hydrophobic samples with contact angles between 99 and 178.9°. The method was further used to produce detailed advancing and receding contact angle maps of surfaces with wetting patterns with an unprecedented resolution of 3 µm.
RESUMEN
A water droplet can bounce off superhydrophobic surfaces multiple times before coming to a stop. The energy loss for such droplet rebounds can be quantified by the ratio of the rebound speed UR and the initial impact speed UI; i.e., its restitution coefficient e = UR/UI. Despite much work in this area, a mechanistic explanation for the energy loss for rebounding droplets is still lacking. Here, we measured e for submillimeter- and millimeter-sized droplets impacting two different superhydrophobic surfaces over a wide range of UI (4-700 cm s-1). We proposed simple scaling laws to explain the observed nonmonotonic dependence of e on UI. In the limit of low UI, energy loss is dominated by contact-line pinning and e is sensitive to the surface wetting properties, in particular to contact angle hysteresis Δ cos θ of the surface. In contrast, e is dominated by inertial-capillary effects and does not depend on Δ cos θ in the limit of high UI.
RESUMEN
A myriad of natural surfaces such as plant leaves and insect wings can repel water and remain unwetted inspiring scientists and engineers to develop water-repellent surfaces for various applications. Those natural and artificial water-repellent surfaces are typically opaque, containing micro- and nano-roughness, and their wetting properties are determined by the details at the actual liquid-solid interface. However, a generally applicable way to directly observe moving contact lines on opaque water-repellent surfaces is missing. Here, we show that the advancing and receding contact lines and corresponding contact area on micro- and nano-rough water-repellent surfaces can be readily and reproducibly quantified using a transparent droplet probe. Combined with a conventional optical microscope, we quantify the progression of the apparent contact area and apparent contact line irregularity in different types of superhydrophobic silicon nanograss surfaces. Contact angles near 180° can be determined with an uncertainty as low as 0.2°, that a conventional contact angle goniometer cannot distinguish. We also identify the pinning/depinning sequences of a pillared model surface with excellent repeatability and quantify the progression of the apparent contact interface and contact angle of natural plant leaves with irregular surface topography.
RESUMEN
Tunable and responsive surfaces offer routes to multiple functionalities ranging from superhydrophobic surfaces to controlled adhesion. Inspired by cilia structure in the respiratory pathway, magnetically responsive periodic arrays of flexible and magnetic thiol-ene micropillars are fabricated. Omnidirectional collective bending of the pillar array in magnetic field is shown. Local non-contact actuation of a single pillar is achieved using an electromagnetic needle to probe the responsiveness and the elastic properties of the pillars by comparing the effect of thiol-ene crosslinking density to pillar bending. The suitable thiol-ene components for flexible and stiff magnetic micropillars and the workable range of thiol-to-allyl ratio are identified. The wettability of the magnetic pillars can be tailored by chemical and topography modification of the pillar surface. Low-surface-energy self-assembled monolayers are grafted by UV-assisted surface activation, which is also used for surface topography modification by covalent bonding of micro- and nanoparticles to the pillar surface. The modified thiol-ene micopillars are resistant to capillarity-driven collapse and they exhibit low contact angle hysteresis, allowing water droplet motion driven by repeated bending and recovery of the magnetic pillars in an external magnetic field. Transport of polyethylene microspheres is also demonstrated.
Asunto(s)
Compuestos Alílicos/química , Química Clic , Nanopartículas de Magnetita/química , Compuestos de Sulfhidrilo/química , Elasticidad , Campos Electromagnéticos , Interacciones Hidrofóbicas e Hidrofílicas , Tamaño de la Partícula , Glicoles de Propileno/química , Sulfuros/síntesis química , Sulfuros/química , Propiedades de Superficie , Triazinas/química , Agua/química , HumectabilidadRESUMEN
Biofouling imposes a significant threat for sensing probes used in vivo. Antifouling strategies commonly utilize a protective layer on top of the electrode but this may compromise performance of the electrode. Here, we investigated the effect of surface topography and chemistry on fouling without additional protective layers. We have utilized two different carbon materials; tetrahedral amorphous carbon (ta-C) and SU-8 based pyrolytic carbon (PyC) in their typical smooth thin film structure as well as with a nanopillar topography templated from black silicon. The near edge X-ray absorption fine structure (NEXAFS) spectrum revealed striking differences in chemical functionalities of the surfaces. PyC contained equal amounts of ketone, hydroxyl and ether/epoxide groups, while ta-C contained significant amounts of carbonyl groups. Overall, oxygen functionalities were significantly increased on nanograss surfaces compared to the flat counterparts. Neither bovine serum albumin (BSA) or fetal bovine serum (FBS) fouling caused major effects on electron transfer kinetics of outer sphere redox (OSR) probe Ru(NH3)63+ on any of the materials. In contrast, negatively charged OSR probe IrCl62- kinetics were clearly affected by fouling, possibly due to the electrostatic repulsion between redox species and the anionically-charged proteins adsorbed on the electrode and/or stronger interaction of the proteins and positively charged surface. The OSR probe kinetics were less affected by fouling on PyC, probably due to conformational changes of proteins on the surface. Dopamine (DA) was tested as an inner sphere redox (ISR) probe and as expected, the kinetics were heavily dependent on the material; PyC had very fast electron transfer kinetics, while ta-C had sluggish kinetics. DA electron transfer kinetics were heavily affected on all surfaces by fouling (ΔEp increase 30-451%). The effect was stronger on PyC, possibly due to the more strongly adhered protein layer limiting the access of the probe to the inner sphere.
Asunto(s)
Incrustaciones Biológicas , Técnicas Biosensibles , Carbono/química , Electroquímica , Cinética , Oxidación-Reducción , Proteínas/química , Silicio/química , Propiedades de SuperficieRESUMEN
We introduce rapid replica molding of ordered, high-aspect-ratio, thiol-ene micropillar arrays for implementation of microfluidic immobilized enzyme reactors (IMERs). By exploiting the abundance of free surface thiols of off-stoichiometric thiol-ene compositions, we were able to functionalize the native thiol-ene micropillars with gold nanoparticles (GNPs) and these with proteolytic α-chymotrypsin (CHT) via thiol-gold interaction. The micropillar arrays were replicated via PDMS soft lithography, which facilitated thiol-ene curing without the photoinitiators, and thus straightforward bonding and good control over the surface chemistry (number of free surface thiols). The specificity of thiol-gold interaction was demonstrated over allyl-rich thiol-ene surfaces and the robustness of the CHT-IMERs at different flow rates and reaction temperatures using bradykinin hydrolysis as the model reaction. The product conversion rate was shown to increase as a function of decreasing flow rate (increasing residence time) and upon heating of the IMER to physiological temperature. Owing to the effective enzyme immobilization onto the micropillar array by GNPs, no further purification of the reaction solution was required prior to mass spectrometric detection of the bradykinin hydrolysis products and no clogging problems, commonly associated with conventional capillary packings, were observed. The activity of the IMER remained stable for at least 1.5 h (continuous use), suggesting that the developed protocol may provide a robust, new approach to implementation of IMER technology for proteomics research. Graphical abstract.
Asunto(s)
Quimotripsina/química , Enzimas Inmovilizadas/química , Oro/química , Dispositivos Laboratorio en un Chip , Nanopartículas del Metal/química , Compuestos de Sulfhidrilo/química , Animales , Bradiquinina/química , Bovinos , Hidrólisis , Modelos MolecularesRESUMEN
Reliable characterization of wetting properties is essential for the development and optimization of superhydrophobic surfaces. Here, the dynamics of superhydrophobicity is studied including droplet friction and wetting transitions by using droplet oscillations on micropillared surfaces. Analyzing droplet oscillations by high-speed camera makes it possible to obtain energy dissipation parameters such as contact angle hysteresis force and viscous damping coefficients, which indicate pinning and viscous losses, respectively. It is shown that the dissipative forces increase with increasing solid fraction and magnetic force. For 10 µm diameter pillars, the solid fraction range within which droplet oscillations are possible is between 0.97% and 2.18%. Beyond the upper limit, the oscillations become heavily damped due to high friction force. Below the lower limit, the droplet is no longer supported by the pillar tops and undergoes a Cassie-Wenzel transition. This transition is found to occur at lower pressure for a moving droplet than for a static droplet. The findings can help to optimize micropillared surfaces for low-friction droplet transport.
RESUMEN
The non-stick properties of thin-film coatings on dental-restorative instruments were investigated by static contact-angle measurement using dental filler resin as well as by scanning electron microscopy of the amount of sticking dental restorative material. Furthermore, using a customized dipping measurement set-up, non-stick properties were evaluated by measuring force-by-time when the instrument was pulled out of restorative material. Minor improvements in non-stick properties were obtained with commercial diamond-like carbon and commercial polytetrafluoroethylene-based coatings. Major improvements were obtained with an in-house fabricated superhydrophobic coating prepared by a multistep process consisting of surface microstructuring by etching in hydrogen fluoride (HF): hydrogen peroxide (H2 O2 ) (1:1; vol/vol), atomic layer deposition of a 7 nm coating of aluminium oxide and titanium oxide, and a self-assembled monolayer of fluorinated organosilicon. Superhydrophobic coatings provide a possible future solution to prevent unwanted adnerence of composite restorative material to dental instruments.
Asunto(s)
Materiales Biocompatibles Revestidos/química , Instrumentos Dentales , Diseño de Equipo , Resinas Sintéticas/química , Grabado Ácido Dental , Óxido de Aluminio/química , Ácido Fluorhídrico/química , Peróxido de Hidrógeno/química , Interacciones Hidrofóbicas e Hidrofílicas , Ensayo de Materiales , Microscopía Electrónica de Rastreo , Politetrafluoroetileno/química , Acero Inoxidable/química , Propiedades de Superficie , Titanio/químicaRESUMEN
Synaptic adhesion molecules are key components in development of the brain, and in the formation of neuronal circuits, as they are central in the assembly and maturation of chemical synapses. Several families of neuronal adhesion molecules have been identified such as the neuronal cell adhesion molecules, neurexins and neuroligins, and in particular recently several leucine-rich repeat proteins, e.g., Netrin G-ligands, SLITRKs, and LRRTMs. The LRRTMs form a family of four proteins. They have been implicated in excitatory glutamatergic synapse function and were specifically characterized as ligands for neurexins in excitatory synapse formation and maintenance. In addition, LRRTM3 and LRRTM4 have been found to be ligands for heparan sulfate proteoglycans, including glypican. We report here the crystal structure of a thermostabilized mouse LRRTM2, with a Tm 30 °C higher than that of the wild-type protein. We localized the neurexin binding site to the concave surface based on protein engineering, sequence conservation, and prior information about the interaction of the ligand with neurexins, which allowed us to propose a tentative model for the LRRTM-neurexin interaction complex. We also determined affinities of the thermostabilized LRRTM2 and wild-type LRRTM1 and LRRTM2 for neurexin-ß1 with and without Ca(2+). Cell culture studies and binding experiments show that the engineered protein is functional and capable of forming synapselike contacts. The structural and functional data presented here provide the first structure of an LRRTM protein and allow us to propose a model for the molecular mechanism of LRRTM function in the synaptic adhesion.
Asunto(s)
Moléculas de Adhesión Celular Neuronal/genética , Moléculas de Adhesión Celular Neuronal/metabolismo , Modelos Moleculares , Proteínas del Tejido Nervioso/genética , Proteínas del Tejido Nervioso/metabolismo , Moléculas de Adhesión de Célula Nerviosa/genética , Moléculas de Adhesión de Célula Nerviosa/metabolismo , Sinapsis/metabolismo , Secuencia de Aminoácidos , Animales , Proteínas de Unión al Calcio , Moléculas de Adhesión Celular Neuronal/química , Células Cultivadas , Cristalografía por Rayos X , Drosophila , Células HEK293 , Humanos , Insectos , Proteínas de la Membrana , Ratones , Datos de Secuencia Molecular , Proteínas del Tejido Nervioso/química , Moléculas de Adhesión de Célula Nerviosa/química , Neuronas/metabolismo , Unión Proteica/fisiología , Estructura Secundaria de Proteína , Estructura Terciaria de Proteína , RatasRESUMEN
Directional imbibition of oils (hexadecane, tetradecane, and dodecane) and water is demonstrated on a chemically patterned silicon micropillar array. Four different directional imbibition types are shown: unidirectional, two types of bidirectional and tridirectional imbibition. The surfaces consist of a silicon micropillar array with an overlaid surface chemistry pattern. This configuration leads to anisotropic wetting behaviour into various directions of the advancing meniscus. Due to the free energy landscape obtained, the advancing meniscus gets pinned in some directions (determined by the surface chemistry pattern) while it is free to move to the remaining directions. The conditions for directional imbibition and design criteria for the surfaces are derived and discussed.
RESUMEN
Nature offers exciting examples for functional wetting properties based on superhydrophobicity, such as the self-cleaning surfaces on plant leaves and trapped air on immersed insect surfaces allowing underwater breathing. They inspire biomimetic approaches in science and technology. Superhydrophobicity relies on the Cassie wetting state where air is trapped within the surface topography. Pressure can trigger an irreversible transition from the Cassie state to the Wenzel state with no trapped air--this transition is usually detrimental for nonwetting functionality and is to be avoided. Here we present a new type of reversible, localized and instantaneous transition between two Cassie wetting states, enabled by two-level (dual-scale) topography of a superhydrophobic surface, that allows writing, erasing, rewriting and storing of optically displayed information in plastrons related to different length scales.
RESUMEN
Droplet digital PCR (ddPCR) is a technique in which PCR reaction is divided into thousands of nanoliter-sized droplets and has proven to be a great tool in virus diagnostics. Compared to the gold standard system quantitative real-time PCR (RT-qPCR), ddPCR functions particularly well when dealing with samples with low template counts, such as viral concentration. This feature makes the technique suitable for early detection of the virus. In this study, a novel portable PDMS ddPCR chip is introduced. The chip functions without external pumps using manual pressurization with a multichannel pipet. The created droplets are monodispersed and form a monolayer on the chip's collection chamber, from where they can be effortlessly imaged. Droplets were analyzed and counted using artificial intelligence. The use of the manually pressurized chip was demonstrated for a SARS-CoV-2 assay, which takes advantage of isothermal strand invasion-based amplification (SIBA) technology, allowing quick and accurate, even point-of-care analysis of the sample. The results demonstrate that SIBA assays can be divided into nanoliter-sized droplets and used as quantitative assays, giving an approximation of the samples' viral count.
RESUMEN
Friction determines whether liquid droplets slide off a solid surface or stick to it. Surface heterogeneity is generally acknowledged as the major cause of increased contact angle hysteresis and contact line friction of droplets. Here we challenge this long-standing premise for chemical heterogeneity at the molecular length scale. By tuning the coverage of self-assembled monolayers (SAMs), water contact angles change gradually from about 10° to 110° yet contact angle hysteresis and contact line friction are low for the low-coverage hydrophilic SAMs as well as high-coverage hydrophobic SAMs. Their slipperiness is not expected based on the substantial chemical heterogeneity of the SAMs featuring uncoated areas of the substrate well beyond the size of a water molecule as probed by metal reactants. According to molecular dynamics simulations, the low friction of both low- and high-coverage SAMs originates from the mobility of interfacial water molecules. These findings reveal a yet unknown and counterintuitive mechanism for slipperiness, opening new avenues for enhancing the mobility of droplets.
RESUMEN
The interface between engineering and molecular life sciences has been fertile ground for advancing our understanding of complex biological systems. Engineered microstructures offer a diverse toolbox for cellular and molecular biologists to direct the placement of cells and small organisms, and to recreate biological functions in vitro: cells can be positioned and connected in a designed fashion, and connectivity and community effects of cells studied. Because of the highly polar morphology and finely compartmentalized functions of neurons, microfabricated cell culture systems and related on-chip technologies have become an important enabling platform for studying development, function and degeneration of the nervous system at the molecular and cellular level. Here we review some of the compartmentalization techniques developed so far to highlight how high-precision control of neuronal connectivity allows new approaches for studying axonal and synaptic biology.
Asunto(s)
Microtecnología/métodos , Nanotecnología/métodos , Neurobiología , Animales , Axones/metabolismo , Caenorhabditis elegans , Drosophila melanogaster , Microfluídica/métodos , Modelos Animales , Neuronas/citología , Neuronas/fisiologíaRESUMEN
Oxygen tension varies during placental and fetal development. Although hypoxia drives early trophoblast invasion, low placental oxygen levels during pregnancy show association with pregnancy complications including fetal growth restriction and preeclampsia. JEG-3 cells are often used as a trophoblast model. We studied transcriptional changes of JEG-3 cells on a uterine leiomyoma derived matrix Myogel. This might be the closest condition to the real uterine environment that we can get for an in vitro model. We observed that culturing JEG-3 cells on the leiomyoma matrix leads to strong stimulation of ribosomal pathways, energy metabolism, and ATP production. Furthermore, Myogel improved JEG-3 cell adherence in comparison to tissue culture treated plastic. We also included PDMS microchip hypoxia creation, and observed changes in oxidative phosphorylation, oxygen related genes and several hypoxia genes. Our study highlights the effects of Myogel matrix on growing JEG-3 cells, especially on mitochondria, energy metabolism, and protein synthesis.
RESUMEN
Stem cell renewal and differentiation are regulated by interactions with the niche. Although multiple cell populations have been identified in distinct anatomical compartments, little is known about niche-specific molecular factors. Using skin as a model system and combining single-cell RNA-seq data analysis, immunofluorescence, and transgenic mouse models, we show that the transmembrane protein embigin is specifically expressed in the sebaceous gland and that the number of embigin-expressing cells is negatively regulated by Wnt. The loss of embigin promotes exit from the progenitor compartment and progression toward differentiation, and also compromises lipid metabolism. Embigin modulates sebaceous niche architecture by affecting extracellular matrix organization and basolateral targeting of monocarboxylate transport. We discover through ligand screening that embigin is a direct fibronectin receptor, binding to the N-terminal fibronectin domain without impairing integrin function. Our results solve the long-standing question of how embigin regulates cell adhesion and demonstrate a mechanism that couples adhesion and metabolism.
Asunto(s)
Integrina alfa5beta1 , Glándulas Sebáceas , Animales , Adhesión Celular , Diferenciación Celular , Fibronectinas , Integrina beta1 , Integrinas/metabolismo , RatonesRESUMEN
Geometric pinning sites can be used to control the lateral spreading and pinning of oils on surfaces. The geometric pinning effect combined with lithographic surface chemistry patterning allows controlling the shapes of oil droplets. We study the confinement effect on test structures of various protruding and intruding geometries, and employ scanning electron microscopy analysis to study the shape of the meniscus at the edges of the chemical patterns. Nanopillar and micropillar topographies are compared, revealing that it is a necessity for accurate oil patterns that the length scale of the roughness is smaller than the resolution of the surface chemistry pattern. We also find that there exists a critical, geometry-dependent threshold contact angle, below which the geometric confinement does not work, as olive oil with a static advancing contact angle of 57° accurately replicated the chemical pattern on top of nanopillar topography, but hexadecane with a static advancing contact angle of 50° penetrated the pinning sites and wetted the whole surface.
Asunto(s)
Aceites/química , Interacciones Hidrofóbicas e Hidrofílicas , Nanoestructuras/química , Tensión SuperficialRESUMEN
A polydimethylsiloxane (PDMS)/Cu superhydrophobic composite material is fabricated by wet etching, electroless plating, and polymer casting. The surface topography of the material emerges from hierarchical micro/nanoscale structures of etched aluminum, which are rigorously copied by plated copper. The resulting material is superhydrophobic (contact angle > 170°, sliding angle < 7° with 7 µL droplets), electrically conductive, elastic and wear resistant. The mechanical durability of both the superhydrophobicity and the metallic conductivity are the key advantages of this material. The material is robust against mechanical abrasion (1000 cycles): the contact angles were only marginally lowered, the sliding angles remained below 10°, and the material retained its superhydrophobicity. The resistivity varied from 0.7 × 10-5 Ωm (virgin) to 5 × 10-5 Ωm (1000 abrasion cycles) and 30 × 10-5 Ωm (3000 abrasion cycles). The material also underwent 10,000 cycles of stretching and bending, which led to only minor changes in superhydrophobicity and the resistivity remained below 90 × 10-5 Ωm.