Exploring the Effectiveness of Carboxymethylated and Crosslinked Albizia procera Gum in Diltiazem Hydrochloride Matrix Tablets: A Comparative Analysis.

This study investigates the efficacy of modified Albizia procera gum as a release-retardant polymer in Diltiazem hydrochloride (DIL) matrix tablets. Carboxymethylated Albizia procera gum (CAP) and ionically crosslinked carboxymethylated Albizia procera gum (Ca-CAP) were utilized, with Ca-CAP synthesized via crosslinking CAP with calcium ions (Ca2+) using calcium chloride (CaCl2). Fourier Transform (FT) IR analysis affirmed polymer compatibility, while differential scanning calorimetry (DSC) and X-ray diffraction (XRD) assessed thermal behavior and crystallinity, respectively. Zeta potential analysis explored surface charge and electrostatic interactions, while rheology examined flow and viscoelastic properties. Swelling and erosion kinetics provided insights into water penetration and stability. CAP's carboxymethyl groups (-CH2-COO-) heightened divalent cation reactivity, and crosslinking with CaCl2 produced Ca-CAP through -CH2-COO- and Ca2+ interactions. Structural similarities between the polymers were revealed by FTIR, with slight differences. DSC indicated modified thermal behavior in Ca-CAP, while Zeta potential analysis showcased negative charges, with Ca-CAP exhibiting lower negativity. XRD highlighted increased crystallinity in Ca-CAP due to calcium crosslinking. Minimal impact on RBC properties was observed with both polymers compared to the positive control as water for injection (WFI). Ca-CAP exhibited improved viscosity, strength, controlled swelling, and erosion, allowing prolonged drug release compared to CAP. Stability studies confirmed consistent six-month drug release, emphasizing Ca-CAP's potential as a stable, sustained drug delivery system over CAP. Robustness and accelerated stability tests supported these findings, underscoring the promise of Ca-CAP in controlled drug release applications.

Evaluating the potential of ethyl cellulose/eudragit-based griseofulvin loaded nanosponge matrix for topical antifungal drug delivery in a sustained release pattern.

Fungal infections are very alarming nowadays and are common throughout the world. Severe fungal infections may lead to a significant risk of mortality and morbidity worldwide. Sustained delivery of antifungal agents is needed to mitigate this problem. In the current study, an attempt has been made to formulate griseofulvin-loaded nanosponges using the quasi-emulsion solvent diffusion technique. For characterization, griseofulvin loaded nanosponges were tested by different instrumental techniques such as optical microscopy, scanning electron microscopy (SEM), powder X-ray diffractometer (PXRD), Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). The antifungal activity of the nanosponges was assessed against Candida albican strain using the agar well-diffusion method. Finally, the drug-loaded nanosponges' in vitro sustained release activity was evaluated. FTIR spectra showed no chemical interference between the drug and polymers. Some of the peaks of the drug are not visible in the FTIR spectrum, which suggests drug entrapment. PXRD data showed that the drug lost its high crystallinity when entrapped in the nanosponge matrix. From the morphological studies via SEM and TEM, a brief idea of the surface morphology of the nanosponges was obtained. The small pores throughout the structure proved its high porosity. The antifungal sensitivity assay was successful, and a zone of inhibition was observed in all the formulations. The in-vitro drug release study showed sustained behaviour. The sustaining effect was due to the polymer and cross-linker used, which gave rise to a porous scaffold matrix. From the results, it can be concluded that griseofulvin-loaded nanosponges can be used for antifungal drug delivery against various topical skin infections.

An overview of preparation and characterization of solid binary system and its application on transdermal film with variation of plasticizers

Chemotherapy induced nausea and vomiting (CINV) and post-operative nausea and vomiting (PONV) is a problem, often occurs in patient. Inspite of high bioavailability, the demerits such as: hepatic first pass metabolism and invasive nature of oral and parenteral dosage forms can be avoided with anti-emetic therapy of transdermal device. The major objective of the present study is to modify the hydrochloride (HCl) form of Ondansetron (OND) to the base form followed by improvement of solubility and permeability of OND by employing solid dispersion (SD) loaded patches. Preformulation study, as observed, begins with an approach to enthuse solubility of OND by SD technique choosing different carriers. The choice of carriers was rationalized by phase solubility study. Several combinations of transdermal films were prepared with pure drug, carriers and SDs with plasticizer Ka values of OND-HPßCD binary system were found lower (54.43 to 187.57 M-1) than that of OND-PVP K-30 binary system (1156.77 to 12203.6 M-1). The drug content of SDs and patches were found satisfactory. Better permeation rate (236.48±3.66 µg/3.935 cm2) with promising flux enhancement (8.30 fold) was found with DBP loaded SD patch (P6*). Hence, enhancement of solubility and permeability of P6* ensures that it can successfully enhance the bioavailability

An attempt to enhance solubility of metoclopramide base by Solid dispersion strategy and its application on development of Transdermal device

Chemotherapy induced nausea and vomiting (CINV) is an issue, which usually occurs in cancer patient. Despite high bioavailability of oral and intravenous administration, these have some drawbacks. The oral route causes hepatic first pass metabolism and intravenous route is invasive in nature. Hence, antiemetic drug by means of transdermal route is necessary to administer in such cases. The aim of the present investigation is to develop suitable Transdermal Therapeutic System (TTS) with an objective to enhance solubility and skin permeability properties of metoclopramide base. Preformulation study begins with an approach to enhance solubility of 40 metoclopramide base by solid dispersion technique. transdermal films were prepared with 41 the solid dispersion as well as with pure drug. Phase solubility study at various temperatures reveals binding constants (Ka, 95-350 M-1 for PVP K30; 56-81 M-1 for HPßCD). Spontaneity of solubilization was justified by AL type linear profiles. The films showed satisfactory diffusion (%), permeation rate and flux after 8 h study. The transdermal patches as prepared were analyzed under FTIR, DSC and SEM. Both solubility and permeability rate in this investigation have been enhanced. So, it can be affirmed that this route would effectively enhance bioavailability