A passive membrane system for on-line mass spectrometry reagent addition.

RATIONALE: Post-separation addition of chemical modifiers in liquid chromatography-mass spectrometry is widely used for improving ionization sensitivity and selectivity. This is typically accomplished using a post-column T-junction, which can result in sample dilution and imperfect mixing. We present a passive semi-permeable hollow fiber membrane approach for the addition of chemical modifiers that avoids these issues. METHODS: Model compounds were directly infused by flow injection to an electrospray ionization triple quadrupole mass spectrometer after passing through a polydimethylsiloxane hollow fiber membrane. Ionization enhancement reagents were introduced into the flowing stream by membrane permeation from aqueous solutions. Ionization enhancement from volatile acids and bases in positive and negative electrospray ionization was evaluated to assess the feasibility of this approach. RESULTS: The membrane-based apparatus resulted in relative ionization enhancement factors of up to 14×, depending upon the analyte, reagent, and ionization mode used. Ionization enhancement signal stability is reasonable (relative standard deviation of 5-7%) for extended periods from the same reagent solution, and minimal analyte dilution is observed. A proof-of-concept demonstration of the chromatographic "trifluoroacetic acid fix" strategy is presented. CONCLUSIONS: An on-line mass spectrometry ionization reagent addition method with potential post-chromatography reagent addition applications was developed using a hollow fiber polydimethylsiloxane membrane. This approach offers a promising alternative to traditional methods requiring additional hardware such as pumps and T-junctions that can result in sample dilution and imperfect reagent mixing.

Membrane Sampling Separates Naphthenic Acids from Biogenic Dissolved Organic Matter for Direct Analysis by Mass Spectrometry.

Oil sands process waters can release toxic naphthenic acids (NAs) into aquatic environments. Analytical techniques for NAs are challenged by sample complexity and interference from naturally occurring dissolved organic matter (DOM). Herein, we report the use of a poly(dimethylsiloxane) (PDMS) polymer membrane for the on-line separation of NAs from DOM and use direct infusion electrospray ionization mass spectrometry to yield meaningful qualitative and quantitative information with minimal sample cleanup. We compare the composition of membrane-permeable species from natural waters fortified with a commercial NA mixture to those derived from weak anion exchange solid-phase extraction (SPE) using high-resolution mass spectrometry. The results show that SPE retains a wide range of carboxylic acids, including biogenic DOM, while permeation through PDMS was selective for petrogenic classically defined NAs (CnH2n+zO2). A series of model compounds (log Kow ∼1-7) were used to characterize the perm-selectivity and reveal the separation is based on hydrophobicity. This convenient sample cleanup method is selective for the O2 class of NAs and can be used prior to conventional analysis or as an on-line analytical strategy when coupled directly to mass spectrometry.

Direct, Isomer-Specific Quantitation of Polycyclic Aromatic Hydrocarbons in Soils Using Membrane Introduction Mass Spectrometry and Chemical Ionization.

Polycyclic aromatic hydrocarbons (PAHs) are routinely screened for in soils, where quantitation of structural isomers is critical due to varying toxicity within PAH isomer classes. While chromatographic methods provide isomer resolution, such strategies are cost and time intensive. To address these challenges, we present condensed phase membrane introduction mass spectrometry using liquid electron ionization/chemical ionization (CP-MIMS-LEI/CI) as a direct mass spectrometry technique that provides rapid, quantitative results for PAH isomer measurements in soil samples. A methanol acceptor phase is flowed through a probe-mounted polydimethylsiloxane hollow fiber membrane directly immersed into a dichloromethane/soil slurry. PAHs and dichloromethane co-permeate the membrane into the acceptor solvent, whereas particulates and charged matrix components remain in the sample. A nanoflow of the membrane permeate is then directly infused into a LEI/CI interfaced triple quadrupole mass spectrometer. Diagnostic PAH adduct ions were formed at either M + 45 ([M + CH2Cl + CH3OH-HCl]+) or M + 47 ([M + CHCl2-HCl]+). This allowed the development of specific MS/MS transitions for individual PAH isomers. These transitions were subsequently used for the direct analyses of PAHs in real soils where CP-MIMS-LEI/CI was shown to be rapid (15 soil samples/h) and sensitive (ng/g level detection limits). CP-MIMS-LEI/CI results compared well to those obtained using GC-MS (average percent difference of -9% across 9 PAHs in 8 soil samples), presenting a compelling argument for direct, quantitative screening of PAHs in soils by CP-MIMS-LEI/CI, particularly given the simple workflow and short analytical duty cycle.

Direct Analysis of Polyaromatic Hydrocarbons in Soil and Aqueous Samples Using Condensed Phase Membrane Introduction Tandem Mass Spectrometry with Low-Energy Liquid Electron Ionization.

Polyaromatic hydrocarbons (PAHs) are listed as priority pollutants by the United States Environmental Protection Agency (U.S. EPA). PAH-contaminated samples often require extensive sample cleanup before analysis, with the method used dependent upon the sample matrix. We present condensed phase membrane introduction mass spectrometry with liquid electron ionization (CP-MIMS-LEI) as a sensitive and universal technique that can directly analyze both aqueous and soil samples for PAHs without the need for sample clean up or instrumental modifications for different matrixes. The method uses a semipermeable hollow fiber membrane immersion probe to transfer analytes from complex samples into a solvent acceptor phase that is directly entrained at nanoliter/min flows to an LEI-interfaced mass spectrometer. The resulting aerosol is desolvated under vacuum leading to analyte vaporization and subsequent electron ionization. Electron energy and LEI vaporization capillary position were examined and optimized for PAHs. The CP-MIMS probe was directly immersed in complex aqueous matrixes, demonstrating low nanogram per liter PAH detection limits and response times of ≤1.6 min. For soil sample analysis, 2-propanol was found to be the optimal PAH sampling solvent. Soil samples were briefly sonicated in 2-propanol, followed by direct CP-MIMS measurement. Soil sample throughput was ca. 15 samples/h, with PAH quantitation successful at microgram per kilogram levels. The workflow is remarkably simple, fast, green, and leads to reproducible results that enable high-throughput screening of heterogeneous soil samples.

Mass Spectrometry Based Approach for Organic Synthesis Monitoring.

Current mass spectrometry-based methodologies for synthetic organic reaction monitoring largely use electrospray ionization (ESI), or other related atmospheric pressure ionization-based approaches. Monitoring of complex, heterogeneous systems may be problematic because of sampling hardware limitations, and many relevant analytes (neutrals) exhibit poor ESI performance. An alternative monitoring strategy addressing this significant impasse is condensed phase membrane introduction mass spectrometry using liquid electron ionization (CP-MIMS-LEI). In CP-MIMS, a semipermeable silicone membrane selects hydrophobic neutral analytes, rejecting particulates and charged chemical components. Analytes partition through the membrane, and are then transported to the LEI interface for sequential nebulization, vaporization, and ionization. CP-MIMS and LEI are both ideal for continuous monitoring applications of hydrophobic neutral molecules. We demonstrate quantitative reaction monitoring of harsh, complex reaction mixtures (alkaline, acidic, heterogeneous) in protic and aprotic organic solvents. Also presented are solvent-membrane compatibility investigations and, in situ quantitative monitoring of catalytic oxidation and alkylation reactions.

Direct quantitation and characterization of fatty acids in salmon tissue by condensed phase membrane introduction mass spectrometry (CP-MIMS) using a modified donor phase.

Existing mass spectrometric methods for the analysis of fatty acids often require derivatization, chromatographic separations, and/or extensive sample preparation. Direct mass spectrometry strategies can avoid these requirements, but may also suffer from poor quantitation and/or lack of sensitivity. Condensed phase-membrane introduction mass spectrometry (CP-MIMS) provides direct quantitative measurements of analytes in complex samples with little or no sample preparation. CP-MIMS uses a semipermeable membrane to transfer neutral, hydrophobic compounds from real-world samples to a mass spectrometer. The results presented utilize aqueous/organic sample solvent (donor) mixtures to allow for the sensitive (pptr) detection of a range of fatty acids. The relative sensitivity across a homologous series of fatty acids is observed to change, favoring short- or long-chain fatty acids, depending on the amount of miscible co-solvent added to the donor phase. Further, lithium acetate added online via the acceptor phase was used in tandem mass spectrometry experiments to determine the location of double bonds in polyunsaturated fatty acids (PUFAs). The method was applied to direct measurements and structural determinations for selected PUFAs in salmon tissue samples. Standard addition was employed to quantify the amount of PUFAs in a variety of salmon samples, yielding 0.27-0.42 and 0.40-0.84 w/w % for eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), respectively, for Sockeye and Chinook salmon, in good agreement with the literature. This work presents, to our knowledge, the first use of CP-MIMS for the direct analysis of fatty acids in oily foodstuff samples. Graphical abstract ᅟ.

Online measurement of phthalate-particulate matter interactions by membrane introduction mass spectrometry (MIMS).

To enable further study and assessment of indoor inhalation exposure risk, an online apparatus enabling measurement of semi-volatile compound partitioning on household particulates was developed. An example for use of the apparatus is described using dimethyl phthalate (DMP). The system employs direct measurement by membrane introduction mass spectrometry (MIMS). The MIMS system was calibrated using known gas phase DMP concentrations produced by gravimetrically calibrated permeation devices. The quantity of DMP sorbed by particles is described first using a model particle type, a reverse-phase liquid chromatography packing material, and then with a household dust sample. In addition, the desorption of semi-volatile compounds from a household dust sample was monitored using the apparatus, and characteristic fragment ion signals for phthalate compounds were observed.

Polymer Inclusion Membranes with Condensed Phase Membrane Introduction Mass Spectrometry (CP-MIMS): Improved Analytical Response Time and Sensitivity.

Condensed phase membrane introduction mass spectrometry (CP-MIMS) is an online, in situ analysis technique for low volatility analytes. Analytes diffuse through a hollow fiber membrane, where they are then dissolved by a liquid (condensed) acceptor phase flowing through the membrane lumen. Permeating analytes are entrained to an atmospheric pressure ionization source for subsequent measurement by a mass spectrometer. Larger analytes, with inherently lower diffusivities, suffer from lengthy response times and lower sensitivity, limiting the use of CP-MIMS for their online, real-time measurement. We present the use of a heptane cosolvent in a methanol acceptor phase in combination with a polydimethylsiloxane (PDMS) membrane. The heptane generates an in situ polymer inclusion membrane (PIM) with the PDMS. We report improved measurement response times and greater sensitivity across a suite of analytes studied (gemfibrozil, nonylphenol, triclosan, 2,4,6-trichlorophenol, and naphthenic acids), with detection limits in the low parts per trillion (ppt) range. These improvements are attributed to increasing analyte diffusivities, as well as increased analyte partitioning across the PIM. Response times are ∼3× faster for the larger analytes studied, and calibration sensitivity is improved by up to ∼3.5× using 0.046 mole fraction heptane in the methanol acceptor. We report the use of short sample exposure times and the use of non-steady-state signals to reduce the analytical duty cycle, and illustrate that the use of a PIM provides a simple and robust variant of CP-MIMS amenable to rapid screening of analytes in complex samples.

A membrane introduction mass spectrometer utilizing ion-molecule reactions for the on-line speciation and quantitation of volatile organic molecules.

RATIONALE: The ability of membrane introduction mass spectrometry to quantitatively resolve low molecular weight volatile organic compounds (VOCs) such as benzene, toluene, ethylbenzene and xylene (BTEX) using electron ionization (EI) can be compromised by isobaric interferences. This work focuses on reducing isobaric interferences with ion-molecule reactions in a portable quadrupole ion trap mass spectrometer for the analysis of VOCs. METHODS: EI was used to produce reagent ions from precursors (chloroform, methyl iodide, trichloroethylene or chlorobenzene) that were continually infused into the helium acceptor phase upstream of the membrane introduction mass spectrometry (MIMS) sampling interface. The reagent ions were selectively stored in the ion trap, and then allowed to react with target VOC analytes in air samples via ion-molecule reactions within the trap storage volume. A variety of reaction times were examined (50-5000 ms), and the resulting product ions were analyzed in positive ion mode. RESULTS: The detection limits achieved were comparable with those obtained using EI (low ppbv), and in some cases better than for EI coupled with tandem mass spectrometry (MS/MS). For the VOCs studied, isobaric interferences were greatly reduced or eliminated using chloroform as a reagent gas. The predominant ionization mechanism was via adduct formation, although charge transfer and hydride abstractions were also observed. An internal standard was shown to be effective at correcting for signal changes due to consumption of reagent ions when complex mixtures were sampled. CONCLUSIONS: Ion-molecule reactions were exploited to eliminate isobaric interferences that are often encountered in direct, real-time analysis strategies for atmospheric VOC mixtures. The use of a continuously infused internal standard will improve quantitative results in field applications where analyte concentration and sample complexity may be wide ranging.

Photosensitized degradation kinetics of trace halogenated contaminants in natural waters using membrane introduction mass spectrometry as an in situ reaction monitor.

The photochemically mediated dechlorination of polyhalogenated compounds represents a potential decontamination strategy and a relevant environmental process in chemically reducing media. We report the UV irradiation of natural and artificial waters containing natural dissolved organic matter to effect the photo-sensitized degradation of chlorinated organic compounds, including tetrachloromethane, 1,1,1-tricloroethane, perchloroethene, 1,2-dibromo-3-chloropropane and chlorobenzene at trace (ppb) levels in aqueous solution. The degradation kinetics are followed in situ using membrane introduction mass spectrometry. By re-circulating the reaction mixture in a closed loop configuration over a semi-permeable hollow fiber polydimethylsiloxane membrane in a flow cell interface, volatile and semi-volatile compounds are continuously monitored using a quadrupole ion trap mass spectrometer. The time resolved quantitative information provides useful mechanistic insights, including kinetic data. Pseudo first-order rate constants for the degradation of contaminant mixtures in natural waters are reported.

Delicate polydimethylsiloxane hollow fibre membrane interfaces for condensed phase membrane introduction mass spectrometry (CP-MIMS).

RATIONALE: On-line analytical techniques such as condensed phase membrane introduction mass spectrometry (CP-MIMS) permit direct and rapid analyte measurements in complex samples. Direct, rapid analytical methods are desirable because they eliminate potential contamination and/or dilution from sample workup steps, facilitate rapid sample screening and allow 'real-time' monitoring applications. METHODS: PDMS hollow fibre membrane (HFM) flow cell interfaces (215 µm, 35 µm, and 0.5 µm thick composite) were coupled with an electrospray ionization (ESI) triple quadrupole mass spectrometer. A simultaneous push/pull methanol acceptor phase delivery system and membrane mounting via epoxy potting ensured that the delicate membranes were not ruptured during construction or sample measurements. Both flow cell and direct insertion 'J-Probe' interfaces using the 0.5 µm thick composite PDMS HFM were utilized for direct naphthenic acid measurements. RESULTS: Delicate HFM CP-MIMS interfaces were used for the rapid screening and continuous, on-line monitoring of carboxylic acids and hydroxylated compounds directly in complex sample matrices under ambient conditions at pptr - ppb detection limits. Push/pull acceptor phase (methanol) delivery maintained ambient hydrostatic pressures within the HFMs, improving ESI stability and analytical sensitivity, especially with stopped acceptor flow operation. Signal response times less than 2 min were achieved for thin, composite PDMS HFMs at 30°C. The continuous monitoring of naphthenic acid degradation was demonstrated. CONCLUSIONS: Delicate PDMS HFM CP-MIMS interfaces were developed and used for the direct, on-line detection of low volatility, polar analytes in complex aqueous samples. Composite PDMS HFM interfaces yielded the best overall analytical performance improvements, and were used to demonstrate the direct measurement of naphthenic acids in complex aqueous samples.

Measurement of spatial and temporal variation in volatile hazardous air pollutants in Tacoma, Washington, using a mobile membrane introduction mass spectrometry (MIMS) system.

The objective of this study was to use membrane introduction mass spectrometry (MIMS), implemented on a mobile platform, in order to provide real-time, fine-scale, temporally and spatially resolved measurements of several hazardous air pollutants. This work is important because there is now substantial evidence that fine-scale spatial and temporal variations of air pollutant concentrations are important determinants of exposure to air pollution and adverse health outcomes. The study took place in Tacoma, WA during periods of impaired air quality in the winter and summer of 2008 and 2009. Levels of fine particles were higher in winter compared to summer, and were spatially uniform across the study area. Concentrations of vapor phase pollutants measured by membrane introduction mass spectrometry (MIMS), notably benzene and toluene, had relatively uniform spatial distributions at night, but exhibited substantial spatial variation during the day-daytime levels were up to 3-fold higher at traffic-impacted locations compared to a reference site. Although no direct side-by-side comparison was made between the MIMS system and traditional fixed site monitors, the MIMS system typically reported higher concentrations of specific VOCs, particularly benzene, ethylbenzene and naphthalene, compared to annual average concentrations obtained from SUMA canisters and gas chromatographic analysis at the fixed sites.

Unique hepatic maternal transfer pattern of trace metals and perfluoroalkyl substances (PFAS) in a bluntnose sixgill shark (Hexanchus griseus).

The fate and distribution of environmental contaminants includes bioaccumulation within marine organisms. A deceased 4-m long adult female bluntnose sixgill shark, pregnant with 72 pups, was recovered from Coles Bay on Vancouver Island, BC, Canada in 2019. This specimen provided a unique opportunity to examine maternal transfer of contaminants in a yolk-sac viviparous shark species. Liver subsamples of the adult and offspring were analyzed for 18 targeted inorganic elements by inductively coupled plasma optical emission spectroscopy (ICP-OES) and 21 targeted perfluoroalkyl substances (PFAS) by liquid chromatography-electrospray ionization-high resolution mass spectrometry (LC-ESI-Orbitrap MS). The maternal-offspring transfer efficiencies in liver tissue were subsequently examined for both contaminant classes. Concentrations of all detectable metals apart from calcium and magnesium were found to be higher in the mother compared to the offspring, including substantial levels of toxic cadmium (6 ± 2 mg kg-1 dw) and lead (7 ± 3 mg kg-1 dw). Conversely, high maternal transfer efficiencies were observed for PFAS (i.e., ΣPFAS = 71 ± 9 ng g-1 ww in offspring compared to 13 ± 9 ng g-1 ww in the mother). This study highlighted the unique maternal transfer characteristics of PFAS in bluntnose sixgill sharks depending on the structure of the polar head group, with greater liver-to-liver transfer efficiencies observed for perfluorocarboxylic acids (PFCAs) than perfluorosulfonic acids (PFSAs) of the same fluorocarbon chain length.

A miniature condensed-phase membrane introduction mass spectrometry (CP-MIMS) probe for direct and on-line measurements of pharmaceuticals and contaminants in small, complex samples.

RATIONALE: High-throughput, automated analytical measurements are desirable in many analytical scenarios, as are rapid sample pre-screening techniques to identify 'positive' samples for subsequent measurements using more time-consuming conventional methodologies (e.g., liquid chromatography/mass spectrometry (LC/MS)). A miniature condensed-phase membrane introduction mass spectrometry (CP-MIMS) probe for the direct and continuous, on-line measurement of pharmaceuticals and environmental contaminants in small, complex samples is presented. METHODS: A miniature polydimethylsiloxane hollow fibre membrane (PDMS-HFM) probe is coupled with an electrospray ionization (ESI) triple quadrupole mass spectrometer. Analytes are transported from the probe to the ESI source by a methanol acceptor phase. The probe can be autosampler mounted and directly inserted in small samples (≥400 µL) allowing continuous and simultaneous pptr-ppb level detection of target analytes (chlorophenols, triclosan, gemfibrozil, nonylphenol) in complex samples (artificial urine, beer, natural water, waste water, plant tissue). RESULTS: The probe has been characterized and optimized for acceptor phase flow rate, sample mixing and probe washing. Signal response times, detection limits and calibration data are given for selected ion monitoring (SIM) and tandem mass spectrometry (MS/MS) measurements of target analytes at trace levels. Comparisons with flow cell type CP-MIMS systems are given. Analyte depletion effects are evaluated for small samples (≥400 µL). On-line measurements in small volumes of complex samples, temporally resolved reaction monitoring and in situ/in vivo demonstrations are presented. CONCLUSIONS: The miniature CP-MIMS probe developed was successfully used for the direct, on-line detection of target analytes in small volumes (40 mL to 400 µL) of complex samples at pptr to low ppb levels. The probe can be readily automated as well as deployed for in situ/in vivo monitoring, including reaction monitoring, small sample measurements and direct insertion in living plant tissue.

Monitoring microplastic-contaminant sorption processes in real-time using membrane introduction mass spectrometry.

Microplastics are environmentally ubiquitous and their role in the fate and distribution of trace contaminants is of emerging concern. We report the first use of membrane introduction mass spectrometry to directly monitor the rate and extent of microplastic-contaminant sorption. Target contaminant (naphthalene, anthracene, pyrene, and nonylphenol) sorption behaviours were examined at nanomolar concentrations with four plastic types: low density polyethylene (LDPE), high density polyethylene (HDPE), polypropylene (PP), and polystyrene (PS). Under the conditions employed here, short-term sorption kinetics were assessed using on-line mass spectrometry for up to one hour. Subsequent sorption was followed by periodically measuring contaminant concentrations for up to three weeks. Short-term sorption followed first order kinetics with rate constants that scaled with hydrophobicity for the homologous series of polycyclic aromatic hydrocarbons (PAHs). Sorption rate constants on LDPE for equimolar solutions of naphthalene, anthracene, and pyrene were 0.5, 2.0, and 2.2 h-1, respectively, while nonylphenol did not sorb to pristine plastics over this time period. Similar trends among contaminants were observed for other pristine plastics with 4- to 10-fold faster sorption rates associated with LDPE when compared to PS and PP. Sorption was largely complete after three weeks, with the percent analyte sorbed ranging from 40-100% across various microplastic-contaminant combinations. Photo-oxidative ageing of LDPE had little effect on PAH sorption. However, a marked increase in nonylphenol sorption was consistent with increased hydrogen-bonding interactions. This work provides kinetic insights into surface interactions and describes a powerful experimental platform to directly observe contaminant sorption behaviours in complex samples under a variety of environmentally relevant conditions.

Automated, High-Throughput Analysis of Tire-Derived p-Phenylenediamine Quinones (PPDQs) in Water by Online Membrane Sampling Coupled to MS/MS.

The tire-derived contaminant N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine quinone (6-PPDQ) was recently identified as a potent toxin to coho salmon (Oncorhynchus kisutch). Studies investigating 6-PPDQ have employed solid-phase extraction (SPE) or liquid-liquid extraction (LLE) with liquid chromatography-mass spectrometry (LC-MS), providing excellent sensitivity and selectivity. However, cleanup and pre-enrichment steps (SPE/LLE) followed by chromatographic separation can be time- and cost-intensive, limiting sample throughput. The ubiquitous distribution of 6-PPDQ necessitates numerous measurements to identify hotspots for targeted mitigation. We recently developed condensed phase membrane introduction mass spectrometry (CP-MIMS) for rapid 6-PPDQ analysis (2.5 min/sample), with a simple workflow and low limit of detection (8 ng/L). Here, we describe improved quantitation using isotopically labeled internal standards and inclusion of a suite of PPDQ analogues. A low-cost autosampler and data processing software were developed from a three-dimensional (3D) printer and Matlab to fully realize the high-throughput capabilities of CP-MIMS. Cross-validation with a commercial LC-MS method for 10 surface waters provides excellent agreement (slope: 1.01; R2 = 0.992). We employ this analytical approach to probe fundamental questions regarding sample stability and sorption of 6-PPDQ under lab-controlled conditions. Further, the results for 192 surface water samples provide the first spatiotemporal characterization of PPDQs on Vancouver Island and the lower mainland of British Columbia.

Characterizing photochemical ageing processes of microplastic materials using multivariate analysis of infrared spectra.

Microplastics in the environment are an emerging concern due to impacts on human and environmental health. In addition to direct effects on biota, microplastics influence the fate and distribution of trace organic contaminants through sorption and transport. Environmental weathering may influence the rate and extent of chemical sorption. Changes in the surface characteristics of four common plastics including low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP), and polystyrene (PS) were followed under the influence of both artificial light (UV-B) and natural sunlight for up to six months. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra were collected at regular intervals. Principal component analysis (PCA) of the full dataset of UV-B weathered samples (n >500 spectra) simultaneously discriminated plastic type and extent of photochemical weathering. The magnitude of PCA scores correlated with exposure time and the loadings were consistent with surface chemistry changes including photooxidation. Projecting sunlight and UV-C exposed samples onto this PCA model demonstrated that similar chemical changes occurred, albeit at different rates. The results were compared to the carbonyl index (CI) with similar weathering trends indicating PP weathered at a faster initial rate than LDPE and HDPE. We propose that a multivariate approach is more widely applicable than CI as illustrated by PS, which lacked a stable reference peak. Kinetic analysis of the time series indicated that outdoor weathering occurred 5-12 times slower than the artificial exposure used here, depending on the plastic and the light source employed. The results provide unique insights into weathering processes and the photochemical age of naturally weathered plastics.

Spatial and Temporal Pattern of Norovirus Dispersal in an Oyster Growing Region in the Northeast Pacific.

Contamination of Pacific oysters, Crassostrea gigas, by human norovirus (HuNoV) is a major constraint to sustainable shellfish farming in coastal waters of the Northeast Pacific. HuNoV is not a marine virus and must originate from a human source. A barrier to effective management is a paucity of data regarding HuNoV dispersal in the marine environment. The main objective of this study was to identify the spatial distribution and persistence of HuNoV in an active shellfish farming region in the Northeast Pacific. Market-size C. gigas were sequentially deployed for two-week intervals at 12 sites during the 2020 winter risk period from January to April. Detection of HuNoV quantification was performed by reverse transcription real-time PCR (RTqPCR) according to method ISO 15216-1:2017, with modifications. RTqPCR did not detect GI HuNoV. The estimated prevalence of GII HuNoV in oyster digestive tissue was 0.8 ± 0.2%. Spatiotemporal analysis revealed that contamination of oysters with GII HuNoV changed through time and space during the surveillance period. A single cluster of oysters contaminated with GII.2 HuNoV was detected in a small craft harbor on 23 April. There was no significant increase in the proportion of positive pools in the next nearest sampling station, indicating that HuNoV is likely to disperse less than 7 km from this non-point source of contamination. Results from this study indicate that HuNoV contamination of coastal waters from non-point sources, such as small craft harbors and urban settings, can pose a significant localised risk to shellfish farming operations in the region.

Measurement of Diacetyl and Related Compounds in Coffee Roasteries and Breweries.

α-Diketones such as diacetyl (2,3-butanedione) and 2,3-pentanedione are generated during the roasting and fermentation of foods and are also used as flavoring compounds. Exposure to these compounds has been associated with obliterative bronchiolitis in workers. We report indoor air concentrations of diacetyl and 2,3-pentanedione, as well as acetoin (3-hydroxy-2-butanone), in several small coffee roasteries and breweries using standard integrated air sampling sorbent tubes followed by gas chromatography tandem mass spectrometry as well as the first use of on-site continuous real-time proton-transfer reaction time-of-flight mass spectrometry (PTR-ToF-MS). Diacetyl and 2,3-pentanedione were detected in most of the sorbent samples at concentrations between 0.02 and 8 ppbv, and in general were higher in coffee roasteries compared with breweries. Three integrated air samples, all from the barista area at one facility, exceeded the NIOSH recommended exposure limit (REL) of 5 ppbv for diacetyl. 2,3-Pentanedione concentrations in these three samples were greater than 50% of its REL, but did not exceed it. Acetoin, a precursor to diacetyl, was also detected at concentrations between 0.03 and 5 ppbv in most sorbent tube samples, with concentrations generally higher in breweries. PTR-ToF-MS measurements exhibited similar trends and provided continuous real-time volatile organic compound data that showed episodic excursions with peak concentrations of diacetyl and 2,3-pentanedione between 15 and 20 ppbv. Examination of the time series data identified specific activities associated with peak diketone emissions, including transfer of freshly roasted coffee beans to the cooling tray, or the opening of a brew kettle. Additional indoor air quality parameters including CO2, NO2, and PM2.5 were also assessed on-site. Airway inflammation was assessed in 19 workers before and after each work shift using online measurements of fractional exhaled nitric oxide (FENO). The pre-shift mean FENO was 3.7 (95% confidence interval: -3.6, 11.0) ppbv higher and the post-shift FENO was 7.1 (-1.9, 16.1) ppbv higher for workers at coffee roasteries compared with breweries. The cross-shift change in FENO was 3.4 (-2.8, 9.6) ppbv higher for workers at coffee roasteries compared with breweries. However, none of these differences were statistically significant, and the cross-shift change in FENO was not statistically different from zero for either group of workers. The findings from this pilot study demonstrate that α-diketones and related compounds are present in the indoor air of both breweries and coffee roasteries and may exceed health protective guidelines in coffee roasteries. Additional studies are required to fully characterize worker exposures in these settings and to identify specific work activities and processes associated with high exposures. Engineering controls, including targeted exhaust ventilation and the use of low-cost sensors, are recommended as an approach to protect workers from exposure to hazardous levels of α-diketones.

Aqueous naphthenic acids and polycyclic aromatic hydrocarbons in a meso-scale spill tank affected by diluted bitumen analyzed directly by membrane introduction mass spectrometry.

With the increasing use of unconventional, heavy crude oils there is growing interest in potential impacts of a diluted bitumen (DB) spill in marine and freshwater environments. DB has the potential to release several toxic, trace organic contaminants to the water column. Here, the aqueous concentrations and compositions of two classes of organic contaminants, naphthenic acids (NAs) and polycyclic aromatic hydrocarbons (PAHs), are followed over 8 weeks after a simulated spill of DB (10 L) into a freshwater mesocosm (1200 L) with river sediment (2.4 kg). These complex samples contain biogenic dissolved organic matter, inorganic ions, petroleum contaminants, suspended sediments, and oil droplets. We report the first use of condensed phase membrane introduction mass spectrometry (CP-MIMS) as a direct sampling platform in a complex multi-phase mesocosm spill tank study to measure trace aqueous phase contaminants with little to no sample preparation (dilution and/or pH adjustment). CP-MIMS provides complementary strengths to conventional analytical approaches (e.g., gas- or liquid chromatography mass spectrometry) by allowing the entire sample series to be screened quickly. Trace NAs are measured as carboxylates ([M-H]-) using electrospray ionization and PAHs are detected as radical cations (M+•) using liquid electron ionization coupled to a triple quadrupole mass spectrometer. The DB-affected mesocosm exhibits NA concentrations from 0.3 to 1.2 mg/L, which rise quickly over the first 2 - 5 days , then decrease slowly over the remainder of the study period. The NA profile (measured as the full scan in negative-electrospray ionization at nominal mass resolution) shifts to lower m/z with weathering, a process followed by principal component analysis of the normalized mass spectra. We couple CP-MIMS with high-resolution mass spectrometry to follow changes in molecular speciation over time, which reveals a concomitant shift from classical 'O2' naphthenic acids to more oxidized analogues. Concentrations of PAHs and alkylated analogues (C1 - C4) in the DB-affected water range from 0 to 5 µg/L. Changes in PAH concentrations depend on ring number and degree of alkylation, with small and/or lightly alkylated (C0 - C2) PAH concentrations rising to a maximum in the first 4 - 8 days (100 - 200 h) before slowly decaying over the remainder of the study period. Larger and heavily alkylated (C3 - C4) PAH concentrations generally rise slower, with some species remaining below the detection limit throughout the study period (e.g., C20H12 class including benzo[a]pyrene). In contrast, a control mesocosm (without oil) exhibited NA concentrations below 0.05 mg/L and PAHs were below detection limit. Capitalizing on the rapid analytical workflow of CP-MIMS, we also investigate the impacts of sample filtration at the time of sampling (on NA and PAH data) and sample storage time (on NA data only).