Development of a Charge-Multiplication CMOS Image Sensor Based on Capacitive Trench for Low-Light-Level Imaging.

This paper presents an electron multiplication charge coupled device (EMCCD) based on capacitive deep trench isolation (CDTI) and developed using complementary metal oxide semiconductor (CMOS) technology. The CDTI transfer register offers a charge transfer inefficiency lower than 10-4 and a low dark current o 0.11nA/cm2 at room temperature. In this work, the timing diagram is adapted to use this CDTI transfer register in an electron multiplication mode. The results highlight some limitations of this device in such an EM configuration: for instance, an unexpected increase in the dark current is observed. A design modification is then proposed to overcome these limitations and rely on the addition of an electrode on the top of the register. Thus, this new device preserves the good transfer performance of the register while adding an electron multiplication function. Technology computer-aided design (TCAD) simulations in 2D and 3D are performed with this new design and reveal a very promising structure.

Modeling, Simulation Methods and Characterization of Photon Detection Probability in CMOS-SPAD.

Single-Photon Avalanche Diodes (SPAD) in Complementary Metal-Oxide Semiconductor (CMOS) technology are potential candidates for future "Light Detection and Ranging" (Lidar) space systems. Among the SPAD performance parameters, the Photon Detection Probability (PDP) is one of the principal parameters. Indeed, this parameter is used to evaluate the SPAD sensitivity, which directly affects the laser power or the telescope diameter of space-borne Lidars. In this work, we developed a model and a simulation method to predict accurately the PDP of CMOS SPAD, based on a combination of measurements to acquire the CMOS process doping profile, Technology Computer-Aided Design (TCAD) simulations, and a Matlab routine. We compare our simulation results with a SPAD designed and processed in CMOS 180 nm technology. Our results show good agreement between PDP predictions and measurements, with a mean error around 18.5%, for wavelength between 450 and 950 nm and for a typical range of excess voltages between 15 and 30% of the breakdown voltage. Due to our SPAD architecture, the high field region is not entirely insulated from the substrate, a comparison between simulations performed with and without the substrate contribution indicates that PDP can be simulated without this latter with a moderate loss of precision, around 4.5 percentage points.

Electrical Characterization of the Backside Interface on BSI Global Shutter Pixels with Tungsten-Shield Test Structures on CDTI Process.

A new methodology is presented using well known electrical characterization techniques on dedicated single devices in order to investigate backside interface contribution to the measured pixel dark current in BSI CMOS image sensors technologies. Extractions of interface states and charges within the dielectric densities are achieved. The results show that, in our case, the density of state is not directly the source of dark current excursions. The quality of the passivation of the backside interface appears to be the key factor. Thanks to the presented new test structures, it has been demonstrated that the backside interface contribution to dark current can be investigated separately from other sources of dark current, such as the frontside interface, DTI (deep trench isolation), etc.

Leakage Current Non-Uniformity and Random Telegraph Signals in CMOS Image Sensor Floating Diffusions Used for In-Pixel Charge Storage.

The leakage current non-uniformity, as well as the leakage current random and discrete fluctuations sources, are investigated in pinned photodiode CMOS image sensor floating diffusions. Different bias configurations are studied to evaluate the electric field impacts on the FD leakage current. This study points out that high magnitude electric field regions could explain the high floating diffusion leakage current non-uniformity and its fluctuation with time called random telegraph signal. Experimental results are completed with TCAD simulations allowing us to further understand the role of the electric field in the FD leakage current and to locate a high magnitude electric field region in the overlap region between the floating diffusion implantation and the transfer gate spacer.

Limitations and Drawbacks of DQE Estimation Methods Applied to Electron Detectors.

The DQE is generally accepted as the main figure of merit for the comparison between electron detectors, and most of the time given as a unique number at the Nyquist frequency while it is known to vary with electron dose. It is usually estimated thanks to a method improved by McMullan in 2009. The purpose of this work is to analyse and to criticize this DQE extraction method on the basis of measurement and model results, and to give recommendations for fair comparison between detectors, wondering if the DQE is the right figure of merit for electron detectors.