The need for multicomponent gas standards for breath biomarker analysis.

Exhaled breath is a non-invasive, information-rich matrix with the potential to diagnose or monitor disease, including infectious disease. Despite significant effort dedicated to biomarker identification in case control studies, very few breath tests are established in practice. In this topical review, we identify how gas standards support breath analysis today and what is needed to support further expansion and translation to practice. We examine forensic and clinical breath tests and discuss how confidence has been built through unambiguous biomarker identification and quantitation supported by gas calibration standards. Based on this discussion, we identify a need for multicomponent gas standards with part-per-trillion to part-per-million concentrations. We highlight National Institute of Standards and Technology gas standards developed for atmospheric measurements that are also relevant to breath analysis and describe investigations of long-term stability, chemical reactions, and interactions with gas cylinder wall treatments. An overview of emerging online instruments and their need for gas standards is also presented. This review concludes with a discussion of our ongoing research to examine the feasibility of producing multicomponent gas standards at breath-relevant concentrations. Such standards could be used to investigate interference from ubiquitous endogenous compounds and as a starting point for standards tailored to specific breath tests.

Determination of glyphosate and AMPA in oat products for the selection of candidate reference materials.

The use of reference materials (RMs) is critical for validating and testing the accuracy of analytical protocols. The National Institute of Standards and Technology (NIST) is in initial stages of developing a glyphosate in oats RM. The first aim of this study was to optimize and validate a robust method for the extraction and analysis of glyphosate and aminomethylphosphonic acid (AMPA). The optimized method was used to screen thirteen commercially available oat products to identify candidate RMs. Glyphosate was detected in all samples, with the highest glyphosate mass fraction of 1100 ng/g; lower levels were measured in grains from organic agriculture. AMPA was quantified in nine samples up to 40 ng/g. The findings of this study led to the identification of candidate RMs, with "high" and "low" glyphosate levels. A preliminary stability study determined that glyphosate is stable in oat material at room temperature for six months.

Semicontinuous PM2.5 and PM10 mass and composition measurements in Lindon, Utah, during winter 2007.

The U.S. Environmental Protection Agency is promoting the development and application of sampling methods for the semicontinuous determination of fine particulate matter (PM2.5, particles with an aerodynamic diameter <2.5 microm) mass and chemical composition. Data obtained with these methods will significantly improve the understanding of the primary sources, chemical conversion processes, and meteorological atmospheric processes that lead to observed PM2.5 concentrations and will aid in the understanding of the etiology of PM2.5-related health effects. During January and February 2007, several semicontinuous particulate matter (PM) monitoring systems were compared at the Utah State Lindon Air Quality Sampling site. Semicontinuous monitors included instruments to measure total PM2.5 mass (filter dynamic measurement system [FDMS] tapered element oscillating microbalance [TEOM], GRIMM), nonvolatile PM2.5 mass (TEOM), sulfate and nitrate (two PM2.5 and one PM10 [PM with an aerodynamic diameter <10 microm] ion-chromatographic-based samplers), and black carbon (aethalometer). PM10 semicontinuous mass measurements were made with GRIMM and TEOM instruments. These measurements were all made on a 1-hr average basis. Source apportionment analysis indicated that sources impacting the site were mainly urban sources and included mobile sources (gasoline and diesel) and residential burning of wood, with some elevated concentrations because of the effect of winter inversions. The FDMS TEOM and GRIMM instruments were in good agreement, but TEOM monitor measurements were low because of the presence of significant semi-volatile material. Semi-volatile mass was present dominantly in the PM2.5 mass.

Hand-portable gas chromatograph-toroidal ion trap mass spectrometer (GC-TMS) for detection of hazardous compounds.

A novel gas chromatograph-mass spectrometer (GC-MS) based on a miniature toroidal ion trap mass analyzer (TMS) and a low thermal mass GC is described. The TMS system has an effective mass/charge (m/z) range of 50-442 with mass resolution at full-width half-maximum (FWHM) of 0.55 at m/z 91 and 0.80 at m/z 222. A solid-phase microextraction (SPME) fiber mounted in a simple syringe-style holder is used for sample collection and introduction into a specially designed low thermal mass GC injection port. This portable GC-TMS system weighs <13 kg (28 lb), including batteries and helium carrier gas cartridge, and is totally self-contained within dimensions of 47 x 36 x 18 cm (18.5 x 14 x 7 in.). System start-up takes about 3 min and sample analysis with library matching typically takes about 5 min, including time for column cool-down. Peak power consumption during sample analysis is about 80 W. Battery power and helium supply cartridges allow 50 and 100 consecutive analyses, respectively. Both can be easily replaced. An on-board library of target analytes is used to provide detection and identification of chemical compounds based on their characteristic retention times and mass spectra. The GC-TMS can detect 200 pg of methyl salicylate on-column. n-Butylbenzene and naphthalene can be detected at a concentration of 100 ppt in water from solid-phase microextraction (SPME) analysis of the headspace. The GC-TMS system has been designed to easily make measurements in a variety of complex and harsh environments.

Qualitative and quantitative approaches in comprehensive two-dimensional gas chromatography.

Comprehensive two-dimensional gas chromatography (GC×GC) offers advantages over one-dimensional gas chromatography (GC) including, high peak capacity, signal enhancement, and structured chromatograms. These advantages have been exploited to solve several analytical problems that are difficult to achieve in GC. In this review, qualitative and quantitative approaches of GC×GC are explored, including targeted, non-targeted, group, and fingerprinting analysis.

Sample introduction in gas chromatography using a coiled wire filament.

A simple device for field sampling and concentration of analytes for subsequent introduction into an injection port for gas chromatographic (GC) analysis has been developed. It consists of a tiny, coiled platinum wire filament (CWF) that is attached to a retractable plunger wire, which fits inside a syringe needle housing. Sampling is accomplished by dipping the end of the CWF in a liquid sample, which is drawn into the wire coil by capillary action, and introducing it into the injection port either before or after allowing the solvent to evaporate. The CWF can be used with or without a nonvolatile chemical coating. A major advantage of this sampling device is that nonvolatile sample matrix components remain on the wire coil, reducing the required injection port and liner cleaning frequency and contamination of the head of the chromatographic column. The coil itself can be easily cleaned between analyses by rinsing and/or burning off residual material in a small flame. The sampling coil facilitates specifically designed chemical reactions in the injection port, such as thermochemolysis and methylation. Applications demonstrated in this work include: (1) direct introduction of samples with little or no pre-treatment, (2) simultaneous thermochemolysis and methylation of lipid-containing samples such as bacteria and bacterial endospores for analysis of biomarkers, and (3) solid phase micro-extraction (SPME) using temporary wire coatings. The CWF allowed for significant reduction in sample preparation time, in most cases to less than a few minutes. The peak shapes examined for polycyclic aromatic hydrocarbon analytes (PAHs) were significantly better (asymmetry factors <1.3) when using the CWF sampling technique compared to splitless and on-column injection techniques (asymmetry factors >1.3). Extraction efficiencies for SPME (especially for high boiling point components such as PAHs) improved by an average of 2.5 times when using the CWF compared to the performance of commercially available SPME fibers. Coiled wire filaments and GC injection port liners were used for more than 100 Bacillus endospore thermochemolysis methylation analyses without the need for cleaning or replacement.