RESUMEN
The universality of physical phenomena is a pivotal concept underlying quantum standards. In this context, the realization of a quantum current standard using silicon single-electron pumps necessitates the verification of the equivalence across multiple devices. Herein, we experimentally investigate the universality of pumped currents from two different silicon single-electron devices which are placed inside the cryogen-free dilution refrigerator whose temperature (mixing chamber plate) was â¼150 mK under the operation of the pump devices. By direct comparison using an ultrastable current amplifier as a galvanometer, we confirm that two pumped currents are consistent with â¼1 ppm uncertainty. Furthermore, we realize quantum-current multiplication with a similar uncertainty by adding the currents of two different gigahertz (GHz)-operated silicon pumps, whose generated currents are confirmed to be identical. These results pave the way for realizing a quantum current standard in the nanoampere range and a quantum metrology triangle experiment using silicon pump devices.
RESUMEN
A novel deep-ridge laser structure with atomic-layer deposition (ALD) sidewall passivation was proposed that enhances the optical characteristics of 8-µm ridge width III-nitride violet lasers on freestanding m-plane GaN substrates. The internal loss was determined using the variable stripe length method, where the laser structure with ALD sidewall passivation showed lower internal loss compared to the conventional shallow-ridge laser design. ALD sidewall passivation plays a critical role in device improvements; compared to the lasers without ALD sidewall passivation, the lasers with ALD sidewall passivation yield improved optoelectrical performance and longer lifetime under continuous-wave operation at high current density. This work demonstrates the importance of ALD sidewall passivation to laser performance, which enables high energy efficiency.
RESUMEN
Phased-array metasurfaces enable the imprinting of complex beam structures onto coherent incident light. Recent demonstrations of photoluminescent phased-array metasurfaces highlight possibilities for achieving similar control in electroluminescent light-emitting diodes (LEDs). However, phased-array metasurface LEDs have not yet been demonstrated owing to the complexities of integrating device stacks and electrodes within nanopatterned metasurfaces. Here, we demonstrate metasurface LEDs that emit directional or focused light. We first design nanoribbon elements that achieve the requisite phase control within typical LED device constraints. Subsequently, we demonstrate unidirectional emission that can be engineered at will via phased-array concepts. This control is further exhibited in metasurface LEDs that directly emit focused beams. Finally, we show that these metasurface LEDs exhibit external quantum efficiencies (EQEs) superior to those of unpatterned LEDs. These results demonstrate metasurface designs that are compatible with high-EQE metal-free LED devices and portend opportunities for new classes of metasurface LEDs that directly produce complex beam structures.
RESUMEN
We demonstrate vertical integration of nitride-based blue/green micro-light-emitting diodes (µLEDs) stacks with independent junctions control using hybrid tunnel junction (TJ). The hybrid TJ was gown by metal organic chemical vapor deposition (p + GaN) and molecular-beam epitaxy (n + GaN). Uniform blue, green and blue/green emission can be generated from different junction diodes. The peak external quantum efficiency (EQE) of the TJ blue µLEDs and green µLEDs with indium tin oxide contact is 30% and 12%, respectively. The carrier transportation between different junction diodes was discussed. This work suggests a promising approach for vertical µLEDs integration to enhance the output power of single LEDs chip and monolithic µLEDs with different emission colors with independent junction control.
RESUMEN
AlGaN-based UV-A LEDs have wide applications in medical treatment and chemical sensing; however, their efficiencies are still far behind visible LEDs or even shorter wavelengths UV-C counterparts because of the large lattice mismatch between the low-Al-content active region and the AlN substrate. In this report, we investigated the composition and thickness of the quantum barrier in the active region in terms of LED performance. Due to the improved strain management and better carrier confinement, efficient UV-A LEDs (320 nm - 330 nm) with EQEs up to 6.8% were demonstrated, among the highest efficiencies at this wavelength range.
RESUMEN
Highly efficient long-wavelength InGaN LEDs have been a research focus in nitride LEDs for their potential applications in displays and solid-state lighting. A key breakthrough has been the use of laterally injected quantum wells via naturally occurring V-defects which promote hole injection through semipolar sidewalls and help to overcome the barriers to carrier injection that plague long wavelength nitride LEDs. In this article, we study V-defect engineered LEDs on (0001) patterned sapphire substrates (PSS) and GaN on (111) Si. V-defects were formed using a 40-period InGaN/GaN superlattice and we report a packaged external quantum efficiency (EQE) of 6.5% for standard 0.1 mm2. LEDs on PSS at 600â nm. We attribute the high EQE in these LEDs to lateral injection via V-defects.
RESUMEN
Deep-ultraviolet (DUV) optoelectronics require innovative light collimation and extraction schemes for wall-plug efficiency improvements. In this work, we computationally survey material limitations and opportunities for intense, wavelength-tunable DUV reflection using AlN-based periodic hole and pillar arrays. Refractive-index limitations for underlayer materials supporting reflection were identified, and MgF2 was chosen as a suitable low-index underlayer for further study. Optical resonances giving rise to intense reflection were then analyzed in AlN/MgF2 nanostructures by varying film thickness, duty cycle, and illumination incidence angle, and were categorized by the emergence of Fano modes sustained by guided mode resonances (holes) or Mie-like dipole resonances (pillars). The phase-offset conditions between complementary modes that sustain high reflectance (%R) were related to a thickness-to-pitch ratio (TPR) parameter, which depended on the geometry-specific resonant mechanism involved (e.g., guided mode vs. Mie dipole resonances) and yielded nearly wavelength-invariant behavior. A rational design space was constructed by pointwise TPR optimization for the entire DUV range (200-320 nm). As a proof of concept, this optimized phase space was used to design reflectors for key DUV wavelengths and achieved corresponding maximum %R of 85% at λ = 211 nm to >97% at λ = 320 nm.
RESUMEN
We report continuous wave operation of electrically injected InGaN laser diodes using nano-porous GaN n-side cladding with 33% porosity. At 454 nm emission wavelength, the pulsed injection slope efficiency is 0.24 W/A with a high loss of 82 cm-1. The considerable 60 cm-1 of excess loss of the nano-porous clad lasers is attributed to scattering at pores in unintentionally 3% porosified layers, supported by numerical modeling. Simulations comparing porous GaN cladding to AlInN cladding for lasers operating at 589 nm indicate that the porous cladding provides similar internal loss and lower thermal impedance.
RESUMEN
GaN lasers with green emission wavelength at λ = 510 nm have been fabricated using novel nano-porous GaN cladding under pulsed electrical injection. The low slope efficiency of 0.13 W/A and high threshold current density of 14 kA/cm2 are related to a combination of poor injection efficiency and high loss, analyzed by the independent characterization methods of variable stripe length and segmented contacts. Continuous wave operation showed narrowed spectra and augmented spontaneous emission.
RESUMEN
Near-band-gap photoemission spectroscopy experiments were performed on p-GaN and p-InGaN/GaN photocathodes activated to negative electron affinity. The photoemission quantum yield of the InGaN samples with more than 5% of indium drops by more than 1 order of magnitude when the temperature is decreased while it remains constant for lower indium content. This drop is attributed to a freezing of photoelectron transport in p-InGaN due to electron localization in the fluctuating potential induced by the alloy disorder. This interpretation is supported by the disappearance at low temperature of the peak in the photoemission spectrum that corresponds to the contribution of the photoelectrons relaxed at the bottom of the InGaN conduction band.
RESUMEN
In this work, we present fully transparent metal organic chemical vapor deposition (MOCVD)-grown InGaN cascaded micro-light-emitting diodes (µLEDs) with independent junction control. The cascaded µLEDs consisted of a blue emitting diode, a tunnel junction (TJ), a green emitting diode, and a TJ, without using any conductive oxide layer. We can control the injection of carriers into blue, green, and blue/green junctions in the same device independently, which show high optical and electrical performance. The forward voltage (Vf) at 20 A/cm2 for the TJ blue µLEDs and TJ green µLEDs is 4.06 and 3.13 V, respectively. These results demonstrate the efficient TJs and fully activated p-type GaN in the cascaded µLEDs. Such demonstration shows the important application of TJs for the integration of µLEDs with multiple color emissions.
RESUMEN
Violet semipolar (20-2-1) InGaN microcavity light-emitting diodes (MC-LED) with a 200 nm ultra-short cavity length were demonstrated. The emission wavelength was 419 nm with a spectrum width of 20 nm. The external quantum efficiency (EQE) of MC-LED was constant at 0.8% for a forward current from 0.5 to 2 mA with the emitting area of 30×30 µm2. With increasing forward current, the peak wavelength and spectrum width of the emission showed almost no changes. For epitaxial growth, metal-organic chemical vapor deposition (MOCVD) was used. Substrate removal and tunnel-junction with an Ag-based electrode made possible the fabrication of the ultra-short 200 nm thick cavity MC-LED. This is more than a factor of 2 improvement compared to previous MC-LEDs of 450 nm cavity thickness sustaining 5 modes.
RESUMEN
We reported significant improvements in device speed by reducing the quantum barrier (QB) thicknesses in the InGaN/GaN multiple quantum well (MQW) photodetectors (PDs). A 3-dB bandwidth of 700 MHz was achieved with a reverse bias of -6 V. Carrier escape lifetimes due to carrier trapping in the quantum wells (QWs) were obtained from both simulation and experimental fitting, identifying carrier trapping as the major speed limiting factor in the InGaN/GaN MQW PDs.
RESUMEN
High performance InGaN micro-size light-emitting diodes (µLEDs) with epitaxial tunnel junctions (TJs) were successfully demonstrated using selective area growth (SAG) by metalorganic chemical vapor deposition (MOCVD). Patterned n + GaN/n-GaN layers with small holes were grown on top of standard InGaN blue LEDs to form TJs using SAG. TJ µLEDs with squared mesa ranging from 10×10 to 100×100 µm2 were fabricated. The forward voltage (Vf) in the reference TJ µLEDs without SAG is very high and decreases linearly from 4.6 to 3.7 V at 20 A/cm2 with reduction in area from 10000 to 100 µm2, which is caused by the lateral out diffusion of hydrogen through sidewall. By contrast, the Vf at 20 A/cm2 in the TJ µLEDs utilizing SAG is significantly reduced to be 3.24 to 3.31 V. Moreover, the Vf in the SAG TJ µLEDs is independent on sizes, suggesting that the hydrogen is effectively removed through the holes on top of the p-GaN surface by SAG. The output power of SAG TJ µLEDs is â¼10% higher than the common µLEDs with indium tin oxide (ITO) contact.
RESUMEN
We demonstrate InGaN-based semipolar 560â nm micro-light-emitting diodes with 2.5% EQE on high-quality and low-defect-density (20-21) GaN templates grown on scalable and low-cost sapphire substrates. Through transmission electron microscopy observations, we discuss how the management of misfit dislocations and their confinement in areas away from the active light-emitting region is necessary for improving device performance. We also discuss how the patterning of semipolar GaN on sapphire influences material properties in terms of surface roughness and undesired faceting in addition to indium segregation at the proximity of defected areas.
RESUMEN
We demonstrate a simple method to fabricate efficient, electrically driven, polarized, and phosphor-free white semipolar (20-21) InGaN light-emitting diodes (LEDs) by adopting a top blue quantum well (QW) and a bottom yellow QW directly grown on (20-21) semipolar bulk GaN substrate. At an injection current of 20 mA, the fabricated 0.1 mm2 size regular LEDs show an output power of 0.9 mW tested on wafer without any backside roughing, a forward voltage of 3.1 V and two emission peaks located at 427 and 560 nm. A high polarization ratio of 0.40 was measured in the semipolar monolithic white LEDs, making them promising candidates for backlighting sources in liquid crystal displays (LCDs). Furthermore, a 3dB modulation bandwidth of 410 MHz in visible light communication (VLC) was obtained in the micro-size LEDs (µLEDs) with a size of 20×20 µm2 and 40×40 µm2, which could overcome the limitation of slow frequency response of yellow phosphor in commercial white LEDs combing blue LEDs and yellow phosphor.
RESUMEN
The electrical and optical improvements of AlGaInP micro-light-emitting diodes (µLEDs) using atomic-layer deposition (ALD) sidewall passivation were demonstrated. Due to the high surface recombination velocity and minority carrier diffusion length of the AlGaInP material system, devices without sidewall passivation suffered from high leakage and severe drop in external quantum efficiency (EQE). By employing ALD sidewall treatments, the 20×20 µm2 µLEDs resulted in greater light output power, size-independent leakage current density, and lower ideality factor. The forward current-voltage characteristic was enhanced by using surface pretreatment. Furthermore, ALD sidewall treatments recovered the EQE of the 20×20 µm2 devices more than 150%. This indicated that AlGaInP µLEDs with ALD sidewall treatments can be used as the red emitter for full-color µLED display applications.
RESUMEN
Single-frequency blue laser sources are of interest for an increasing number of emerging applications but are still difficult to implement and expensive to fabricate and suffer from poor robustness. Here a novel and universal grating design to realize distributed optical feedback in visible semiconductor laser diodes (LDs) was demonstrated on a semipolar InGaN LD, and its unique effect on the laser performance was investigated. For the first time, to the best of our knowledge, a low threshold voltage, record-high power output, and ultra-narrow single-mode lasing were simultaneously obtained on the new laser structure with a thinner p-GaN layer and a third-order phase-shifted embedded dielectric grating. Under continuous-wave operation, such 450 nm lasers achieved 35 dB side-mode suppression ratio, less than 2 pm FWHM, and near 400 mW total output power at room temperature.
RESUMEN
We report observations of lateral mode confinement by a tapering nanoporous-GaN layer in the n-side cladding of a blue-emitting InGaN laser diode grown on the semipolar (202¯1¯) plane of bulk GaN. Little additional confinement occurred in the transverse direction, and the nanoporous layer did not serve as a current aperture. Nanoporous-GaN, with Si-doping of 8x1018 cm-3 and 20% porosity had a bulk resistivity of 3 Ω-cm and a thermal conductivity of 4 W/m-K, in general agreement with data reported on c-plane VCSEL structures. An excess modal loss of 19 cm-1 was found.
RESUMEN
We successfully demonstrated an electrically injected blue(202¯1¯)semipolar vertical-cavity surface-emitting laser with a 5λ cavity length, an ion implanted aperture, and a dual dielectric DBR design. The peak power under pulsed operation was 1.85 mW, the threshold current was 4.6 kA/cm2 , and the differential efficiency was 2.4% for the mode at 445 nm of a device with a 12 µm aperture. Lasing was achieved up to a 50% duty cycle and the thermal impedance was estimated to be 1800 K/W. The lasing emission was found to be 100% plane polarized along the a-direction.