Emulsion Liquid Membranes Based on Os-NP/n-Decanol or n-Dodecanol Nanodispersions for p-Nitrophenol Reduction.

Membrane materials with osmium nanoparticles have been recently reported for bulk membranes and supported composite membrane systems. In the present paper, a catalytic material based on osmium dispersed in n-decanol (nD) or n-dodecanol (nDD) is presented, which also works as an emulsion membrane. The hydrogenation of p-nitrophenol (PNP) is carried out in a reaction and separation column in which an emulsion in the acid-receiving phase is dispersed in an osmium nanodispersion in n-alcohols. The variables of the PNP conversion process and p-aminophenol (PAP) transport are as follows: the nature of the membrane alcohol, the flow regime, the pH difference between the source and receiving phases and the number of operating cycles. The conversion results are in all cases better for nD than nDD. The counter-current flow regime is superior to the co-current flow. Increasing the pH difference between the source and receiving phases amplifies the process. The number of operating cycles is limited to five, after which the regeneration of the membrane dispersion is required. The apparent catalytic rate constant (kapp) of the new catalytic material based on the emulsion membrane with the nanodispersion of osmium nanoparticles (0.1 × 10-3 s-1 for n-dodecanol and 0.9 × 10-3 s-1 for n-decanol) is lower by an order of magnitude compared to those based on adsorption on catalysts from the platinum metal group. The advantage of the tested membrane catalytic material is that it extracts p-aminophenol in the acid-receiving phase.

Comorbidities, Associated Diseases, and Risk Assessment in COVID-19-A Systematic Review.

It is considered that COVID-19's pandemic expansion is responsible for the particular increase in deaths, especially among the population with comorbidities. The health system is often overwhelmed by the large number of cases of patients addressing it, by the regional limitation of funds, and by the gravity of cases at subjects suffering from this pathology. Several associated conditions including diabetes, cardiovascular illnesses, obesity, persistent lung condition, neurodegenerative diseases, etc., increase the mortality risk and hospitalization of subjects suffering from COVID-19. The rapid identification of patients with increased risk of death from the SARS-CoV-2 virus, the stratification in accordance with the risk and the allocation of human, financial, and logistical resources in proportion must be a priority for health systems worldwide.

The Effects of the 'Catabolic Crisis' on Patients' Prolonged Immobility after COVID-19 Infection.

Background and Objectives: Quarantine, isolation and bed rest associated with COVID-19 infection favored the loss of muscle and bone mass, especially in elderly patients. The current study aims to compare the presence of sarcopenia and osteoporosis in patients with a recent (one month) history of SARS-CoV-2 infection versus the general population. Materials and Methods: A cross-sectional study was conducted in which 157 patients were enrolled, divided into two groups, comparable in structure. The COVID-19 group (group C) consisted of 86 patients who were diagnosed with SARS-CoV-2 respiratory infection within the last 30 days. The non-COVID-19 group (group NC) consists of 71 patients who had no clinical signs of respiratory infection and were not quarantined/hospitalized in the last 3 months. Muscle strength, incidence of sarcopenia (using SARC-F score) and osteoporosis (DEXA determination) and physical performance (SPPB score) in the two groups were assessed and compared. Results: No statistically significant differences were found between the SPPB scores of the C group versus the NC group. Statistically significant differences were found in the evaluation of three parameters included in the SARC-F score. Patients in the C group had difficulties in standing up from a chair (p = 0.009) and climbing stairs (p = 0.030) due to lower muscle strength (p = 0.002) compared with patients in the NC group. No correlation of the SARC F and SPPB scores with the T score values obtained by osteo-densitometry was found. Conclusions: The sudden and significant reduction in physical activity, through various measures taken in the general population during the pandemic, led to an increased incidence of sarcopenia, both in patients who did not have COVID-19 infection and among those quarantined/hospitalized for this condition.

The Footprint of Kynurenine Pathway in Neurodegeneration: Janus-Faced Role in Parkinson's Disorder and Therapeutic Implications.

Progressive degeneration of neurons and aggravation of dopaminergic neurons in the substantia nigra pars compacta results in the loss of dopamine in the brain of Parkinson's disease (PD) patients. Numerous therapies, exhibiting transient efficacy have been developed; however, they are mostly accompanied by side effects and limited reliability, therefore instigating the need to develop novel optimistic treatment targets. Significant therapeutic targets have been identified, namely: chaperones, protein Abelson, glucocerebrosidase-1, calcium, neuromelanin, ubiquitin-proteasome system, neuroinflammation, mitochondrial dysfunction, and the kynurenine pathway (KP). The role of KP and its metabolites and enzymes in PD, namely quinolinic acid (QUIN), kynurenic acid (KYNA), 3-hydroxykynurenine (3-HK), 3-hydroxyanthranillic acid (3-HAA), kunurenine-3-monooxygenase (KMO), etc. has been reported. The neurotoxic QUIN, N-methyl-D-aspartate (NMDA) receptor agonist, and neuroprotective KYNA-which antagonizes QUIN actions-primarily justify the Janus-faced role of KP in PD. Moreover, KP has been reported to play a biomarker role in PD detection. Therefore, the authors detail the neurotoxic, neuroprotective, and immunomodulatory neuroactive components, alongside the upstream and downstream metabolic pathways of KP, forming a basis for a therapeutic paradigm of the disease while recognizing KP as a potential biomarker in PD, thus facilitating the development of a suitable target in PD management.

Chemical Profile, Antioxidant Capacity, and Antimicrobial Activity of Essential Oils Extracted from Three Different Varieties (Moldoveanca 4, Vis Magic 10, and Alba 7) of Lavandula angustifolia.

Chemical composition, antioxidant capacity, and antimicrobial activity of lavender essential oils (LEOs) extracted from three different varieties of Lavandula angustifolia Mill. (1-Moldoveanca 4, 2-Vis magic 10, and 3-Alba 7) have been determined. These plants previously patented in the Republic of Moldova were cultivated in an organic agriculture system in the northeastern part of Romania and then harvested in 3 consecutive years (2017-2019) to obtain the essential oils. From the inflorescences in the complete flowering stage, the LEOs were extracted by hydrodistillation. Then, their composition was analyzed by gas chromatography coupled with mass spectrometry (GC-MS) and by Fourier Transformed Infrared spectroscopy (FT-IR). The major identified constituents are as follows: linalool (1: 32.19-46.83%; 2: 29.93-30.97%; 3: 31.97-33.77%), linalyl acetate (1: 17.70-35.18%; 2: 27.55-37.13%; 3: 28.03-35.32%), and terpinen-4-ol (1: 3.63-7.70%; 2: 3.06-7.16%; 3: 3.10-6.53%). The antioxidant capacity as determined by ABTS and DPPH assays indicates inhibition, with the highest activity obtained for LEO var. Alba 7 from 2019. The in vitro antimicrobial activities of the LEOs and combinations were investigated as well, by using the disk diffusion method and minimum inhibitory concentration (MIC) against the Gram-positive bacterial strain Staphylococcus aureus (ATCC 6538), Gram-negative Pseudomonas aeruginosa (ATCC 27858), Escherichia coli (ATCC 25922), the yeast Candida albicans (ATCC 10231), and clinical isolates. Our results have shown that LEOs obtained from the three studied varieties of L. angustifolia manifest significant bactericidal effects against tested microorganisms (Staphylococcus aureus and Escherichia coli), and antifungal effects against Candida albicans. The mixture of LEOs (Var. Alba 7) and geranium, respectively, in tea tree EOs, in different ratios, showed a significant enhancement of the antibacterial effect against all the studied strains, except Pseudomonas aeruginosa.

Chemo-Preventive Action of Resveratrol: Suppression of p53-A Molecular Targeting Approach.

Extensive experimental, clinical, and epidemiological evidence has explained and proven that products of natural origin are significantly important in preventing and/or ameliorating various disorders, including different types of cancer that researchers are extremely focused on. Among these studies on natural active substances, one can distinguish the emphasis on resveratrol and its properties, especially the potential anticancer role. Resveratrol is a natural product proven for its therapeutic activity, with remarkable anti-inflammatory properties. Various other benefits/actions have also been reported, such as cardioprotective, anti-ageing, antioxidant, etc. and its rapid digestion/absorption as well. This review aims to collect and present the latest published studies on resveratrol and its impact on cancer prevention, molecular signals (especially p53 protein participation), and its therapeutic prospects. The most recent information regarding the healing action of resveratrol is presented and concentrated to create an updated database focused on this topic presented above.

Case studies on the physical-chemical parameters' variation during three different purification approaches destined to treat wastewaters from food industry.

The paper presents a set of three interconnected case studies on the depuration of food processing wastewaters by using aeration & ozonation and two types of hollow-fiber membrane bioreactor (MBR) approaches. A secondary and more extensive objective derived from the first one is to draw a clearer, broader frame on the variation of physical-chemical parameters during the purification of wastewaters from food industry through different operating modes with the aim of improving the management of water purification process. Chemical oxygen demand (COD), pH, mixed liquor suspended solids (MLSS), total nitrogen, specific nitrogen (NH4+, NO2-, NO3-) total phosphorous, and total surfactants were the measured parameters, and their influence was discussed in order to establish the best operating mode to achieve the purification performances. The integrated air-ozone aeration process applied in the second operating mode lead to a COD decrease by up to 90%, compared to only 75% obtained in a conventional biological activated sludge process. The combined purification process of MBR and ozonation produced an additional COD decrease of 10-15%, and made the Total Surfactants values to comply to the specific legislation.

Simultaneously Recovery of Thorium and Tungsten through Hybrid Electrolysis-Nanofiltration Processes.

The recovery and recycling of metals that generate toxic ions in the environment is of particular importance, especially when these are tungsten and, in particular, thorium. The radioactive element thorium has unexpectedly accessible domestic applications (filaments of light bulbs and electronic tubes, welding electrodes, and working alloys containing aluminum and magnesium), which lead to its appearance in electrical and electronic waste from municipal waste management platforms. The current paper proposes the simultaneous recovery of waste containing tungsten and thorium from welding electrodes. Simultaneous recovery is achieved by applying a hybrid membrane electrolysis technology coupled with nanofiltration. An electrolysis cell with sulphonated polyether-ether-ketone membranes (sPEEK) and a nanofiltration module with chitosan-polypropylene membranes (C-PHF-M) are used to carry out the hybrid process. The analysis of welding electrodes led to a composition of W (tungsten) 89.4%; Th 7.1%; O2 2.5%; and Al 1.1%. Thus, the parameters of the electrolysis process were chosen according to the speciation of the three metals suggested by the superimposed Pourbaix diagrams. At a constant potential of 20.0 V and an electrolysis current of 1.0 A, the pH is varied and the possible composition of the solution in the anodic workspace is analyzed. Favorable conditions for both electrolysis and nanofiltration were obtained at pH from 6 to 9, when the soluble tungstate ion, the aluminum hydroxide, and solid thorium dioxide were formed. Through the first nanofiltration, the tungstate ion is obtained in the permeate, and thorium dioxide and aluminum hydroxide in the concentrate. By adding a pH 13 solution over the two precipitates, the aluminum is solubilized as sodium aluminate, which will be found after the second nanofiltration in the permeate, with the thorium dioxide remaining integrally (within an error of ±0.1 ppm) on the C-PHF-M membrane.

Thorium Removal, Recovery and Recycling: A Membrane Challenge for Urban Mining.

Although only a slightly radioactive element, thorium is considered extremely toxic because its various species, which reach the environment, can constitute an important problem for the health of the population. The present paper aims to expand the possibilities of using membrane processes in the removal, recovery and recycling of thorium from industrial residues reaching municipal waste-processing platforms. The paper includes a short introduction on the interest shown in this element, a weak radioactive metal, followed by highlighting some common (domestic) uses. In a distinct but concise section, the bio-medical impact of thorium is presented. The classic technologies for obtaining thorium are concentrated in a single schema, and the speciation of thorium is presented with an emphasis on the formation of hydroxo-complexes and complexes with common organic reagents. The determination of thorium is highlighted on the basis of its radioactivity, but especially through methods that call for extraction followed by an established electrochemical, spectral or chromatographic method. Membrane processes are presented based on the electrochemical potential difference, including barro-membrane processes, electrodialysis, liquid membranes and hybrid processes. A separate sub-chapter is devoted to proposals and recommendations for the use of membranes in order to achieve some progress in urban mining for the valorization of thorium.

Chitosan-sEPDM and Melatonin-Chitosan-sEPDM Composite Membranes for Melatonin Transport and Release.

Melatonin is the hormone that focuses the attention of the researchers in the medical, pharmaceutical, materials, and membranes fields due to its multiple biomedical implications. The variety of techniques and methods for the controlled release of melatonin is linked to the multitude of applications, among which sports medicine occupies a special place. This paper presents the preparation and characterization of composite membranes based on chitosan (Chi) and sulfonated ethylene-propylene-diene terpolymer (sEPDM). The membranes were obtained by controlled vacuum evaporation from an 8% sEPDM solution in toluene (w/w), in which chitosan was dispersed in an ultrasonic field (sEPDM:Chi = 1:1, w/w). For the comparative evaluation of the membranes' performances, a melatonin-chitosan-sulfonated ethylene-propylene-diene terpolymer (Mel:Chi:sEPDM = 0.5:0.5:1.0, w/w/w) test membrane was made. The prepared membranes were morphologically and structurally characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), energy-dispersive spectroscopy analysis (EDAX), thermal analysis (TG, DSC), thermal analysis coupled with chromatography and infrared analysis, and contact angle measurements, but also from the point of view of performance in the process of transport and release of melatonin in dedicated environments (aqueous solutions with controlled pH and salinity). The prepared membranes can release melatonin in amounts between 0.4 mg/cm2·per day (sEPDM), 1.6 mg/ cm2·per day (Chi/sEPDM), and 1.25 mg/cm2·per day (Mel/Chi/SEPDM).

Hydrogen Sulphide Sequestration with Metallic Ions in Acidic Media Based on Chitosan/sEPDM/Polypropylene Composites Hollow Fiber Membranes System.

This paper presents the preparation and characterization of composite membranes based on chitosan (Chi), sulfonated ethylene-propylene-diene terpolymer (sEPDM), and polypropylene (PPy), and designed to capture hydrogen sulfide. The Chi/sEPDM/PPy composite membranes were prepared through controlled evaporation of a toluene dispersion layer of Chi:sEPDM 1;1, w/w, deposited by immersion and under a slight vacuum (100 mmHg) on a PPy hollow fiber support. The composite membranes were characterized morphologically, structurally, and thermally, but also from the point of view of their performance in the process of hydrogen sulfide sequestration in an acidic media solution with metallic ion content (Cu2+, Cd2+, Pb2+, and/or Zn2+). The operational parameters of the pertraction were the pH, pM, matrix gas flow rate, and composition. The results of pertraction from synthetic gases mixture (nitrogen, methane, carbon dioxide) indicated an efficient removal of hydrogen sulfide through the prepared composite membranes, as well as its immobilization as sulfides. The sequestration and the recuperative separation, as sulfides from an acid medium, of the hydrogen sulfide reached up to 96%, decreasing in the order: CuS > PbS > CdS > ZnS.

Acute coronary syndromes in diabetic patients, outcome, revascularization, and antithrombotic therapy.

Diabetes exacerbates the progression of atherosclerosis and is associated with increased risk of developing acute coronary syndrome (ACS). Approximatively 25-30% of patients admitted for ACS have diabetes. ACS occurs earlier in diabetics and is associated with increased mortality and a higher risk of recurrent ischemic events. An increased proinflammatory and prothrombotic state is involved in the poorer outcomes of diabetic patients. In the past decade advancement in both percutaneous coronary intervention (PCI) and coronary artery by-pass graft (CABG) techniques and more potent antiplatelet drugs like prasugrel and ticagrelor improved outcomes of diabetic patients with ACS, but this population still experiences worse outcomes compared to non-diabetic patients. While in ST elevation myocardial infarction urgent PCI is the method of choice for revascularization, in patients with non-ST elevation ACS an early invasive approach is suggested by the guidelines, but in the setting of multivessel (MV) or complex coronary artery disease (CAD) the revascularization strategy is less clear. This review describes the accumulating evidence regarding factors involved in promoting increased incidence and poor prognosis of ACS in patients with diabetes, the evolution over time of prognosis and outcomes, revascularization strategies and antithrombotic therapy studied until now.

pH and Design on n-Alkyl Alcohol Bulk Liquid Membranes for Improving Phenol Derivative Transport and Separation.

Regardless of the type of liquid membrane (LM) (Bulk Liquid Membranes (BLM), Supported Liquid Membranes (SLM) or Emulsion Liquid Membranes (ELM)), transport and separation of chemical species are conditioned by the operational (OP) and constructive design parameters (DP) of the permeation module. In the present study, the pH of the aqueous source phase (SP) and receiving phase (RP) of the proposed membrane system were selected as operational parameters. The mode of contacting the phases was chosen as the convective transport generator. The experiments used BLM-type membranes with spheres in free rotation as film contact elements of the aqueous phases with the membrane. The target chemical species were selected in the range of phenol derivatives (PD), 4−nitrophenol (NP), 2,4−dichlorophenol (DCP) and 2,4−dinitrophenol (DNP), all being substances of technical-economic and environmental interest. Due to their acid character, they allow the evaluation of the influence of pH as a determining operational parameter of transport and separation through a membrane consisting of n−octanol or n−decanol (n−AlcM). The comparative study performed for the transport of 4−nitrophenol (NP) showed that the module based on spheres (Ms) was more performant than the one with phase dispersion under the form of droplets (Md). The sphere material influenced the transport of 4−nitrophenol (NP). The transport module with glass spheres (Gl) was superior to the one using copper spheres (Cu), but especially with the one with steel spheres (St). In all the studied cases, the sphere-based module (Ms) had superior transport results compared to the module with droplets (Md). The extraction efficiency (EE) and the transport of 2,4−dichlorophenol (DCP) and 2,4−dinitrophenol (DNP), studied in the module with glass spheres, showed that the two phenolic derivatives could be separated by adjusting the pH of the source phase. At the acidic pH of the source phase (pH = 2), the two derivatives were extracted with good results (EE > 90%), while for pH values ranging from 4 to 6, they could be separated, with DCP having doubled separation efficiency compared to DNP. At a pH of 8 in the source phase, the extraction efficiency halved for both phenolic compounds.

Simultaneous Release of Silver Ions and 10-Undecenoic Acid from Silver Iron-Oxide Nanoparticles Impregnated Membranes.

The bio-medical benefits of silver ions and 10-undecenoic acid in various chemical-pharmaceutical preparations are indisputable, thus justifying numerous research studies on delayed and/or controlled release. This paper presents the effect of the polymer matrix in the simultaneous release of silver ions and 10-undecenoic acid in an aqueous medium of controlled pH and ionic strength. The study took into consideration polymeric matrices consisting of cellulose acetate (CA) and polysulfone (PSf), which were impregnated with oxide nanoparticles containing silver and 10-undecenoic acid. The studied oxide nanoparticles are nanoparticles of iron and silver oxides obtained by an accessible electrochemical method. The obtained results show that silver can be released, simultaneously with 10-undecenoic acid, from an impregnated polymeric membrane, at concentrations that ensure the biocidal and fungicidal capacity. Concentrations of active substances can be controlled by choosing the polymer matrix or, in some cases, by changing the pH of the target medium. In the studied case, higher concentrations of silver ions are released from the polysulfone matrix, while higher concentrations of 10-undecenoic acid are released from the cellulose acetate matrix. The results of the study show that a correlation can be established between the two released target substances, which is dependent on the solubility of the organic compound in the aqueous medium and the interaction of this compound with the silver ions. The ability of 10-undecenoic acid to interact with the silver ion, both through the carboxyl and alkene groups, contributes to the increase in the content of the silver ions transported in the aqueous medium.

Operational Limits of the Bulk Hybrid Liquid Membranes Based on Dispersion Systems.

Liquid membranes usually have three main constructive variants: bulk liquid membranes (BLM), supported liquid membranes (SLM) and emulsion liquid membranes (ELM). Designing hybrid variants is very topical, with the main purpose of increasing the flow of substance through the membrane but also of improving the selectivity. This paper presents the operational limits of some kind of hybrid membrane constituted as a bulk liquid membrane (BLM), but which works by dispersing the aqueous source (SP) and receiving (RP) phases, with the membrane itself being a dispersion of nanoparticles in an organic solvent (NP-OSM). The approached operational parameters were the volume of phases of the hybrid membrane system, the thickness of the liquid membrane, the working temperature, the flow of aqueous phases, the droplet size of the aqueous phases dispersed across the membrane, the nature and concentration of nanoparticles in the membrane, the pH difference between the aqueous phases, the nature of the organic solvent, the salt concentration in the aqueous phases and the nature of transported chemical species. For this study, silver ion (SI) and p-nitrophenol (PNP) were chosen as transportable chemical species, the n-aliphatic alcohols (C6…C12) as membrane organic solvents, 10-undecenoic acid (UDAc) and 10-undecylenic alcohol (UDAl) as carriers and magnetic iron oxides as nanoparticles dispersed in the membrane phase. Under the experimentally established operating conditions, separation efficiencies of over 90% were obtained for both ionic and molecular chemical species (silver ions and p-nitrophenol). The results showed the possibility of increasing the flow of transported chemical species by almost 10 times for the silver ion and approximately 100 times for p-nitrophenol, through the appropriate choice of operational parameters, but they also exposed their limits in relation to the stability of the membrane system.

Therapeutic dilemmas in addressing SARS-CoV-2 infection: Favipiravir versus Remdesivir.

Coronavirus disease 2019 (COVID-19) represents an unmet clinical need, due to a high mortality rate, rapid mutation rate in the virus, increased chances of reinfection, lack of effectiveness of repurposed drugs and economic damage. COVID-19 pandemic has created an urgent need for effective molecules. Clinically proven efficacy and safety profiles have made favipiravir (FVP) and remdesivir (RDV) promising therapeutic options for use against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection. Even though both are prodrug molecules with an antiviral role based on a similar mechanism of action, differences in pharmacological, pharmacokinetic and pharmacotoxicological mechanisms have been identified. The present study aims to provide a comprehensive comparative assessment of FVP and RDV against SARS-CoV-2 infections, by centralizing medical data provided by significant literature and authorized clinical trials, focusing on the importance of a better understanding of the interactions between drug molecules and infectious agents in order to improve the global management of COVID-19 patients and to reduce the risk of antiviral resistance.

Therapeutic approaches in the management of knee osteoarthritis (Review).

Osteoarthritis (OA) is a common, frequently met degenerative disease, that generates pain and decreasing functionality; risk of suffering from this disorder increases with ageing. Being a complex disease, treatment is often difficult due to complications. Knee OA therapy demands a strategy that specialists agree with in considering the clinical symptoms and the disease evolution. The initial management of its treatment should be conservative requiring both a pharmacological and a non-pharmacological approach. If this conservative, noninvasive therapy fails, the surgical approach is discussed. The present review focused on the assessment of therapy choices for patients with knee OA, in order to reduce pain and enhance functionality and knee range of motion, underlying benefits and advantages for each choice. Existing data of available treatment for knee OA, both surgical and nonsurgical were analyzed, focusing on the latest results, indications, developments, and level of evidence provided by the literature in the topic.

Highlighting the advantages and benefits of cementless total knee arthroplasty (Review).

In the field of orthopedic surgery, cemented total knee arthroplasty (TKA) is considered to be one of the gold standards. However, there are categories of patients (i.e., obese and morbidly obese patients, younger than 65 years old) among whom cemented TKA has however a high failure rate. Moreover, the frequency of using uncemented TKA is increasing due to the potential benefits of long-term biological fixation, being an innovative field that addresses a new generation orthopedic surgical treatment which is more suitable for young patients who have good bone quality (good to very good, in terms of density). The survival rates and functional results of the latest generation of cementless TKAs may be similar to functional results and survival rates of cemented prosthesis. In conclusion, this review-type article can be considered a powerful database, extremely informative, dense, and focused on the topic mentioned above, in the interest of all medical professionals and all interested individuals.

Obtaining and Characterizing the Osmium Nanoparticles/n-Decanol Bulk Membrane Used for the p-Nitrophenol Reduction and Separation System.

Liquid membranes based on nanoparticles follow a continuous development, both from obtaining methods and characterization of techniques points of view. Lately, osmium nanoparticles have been deposited either on flat membranes, with the aim of initiating some reaction processes, or on hollow fiber membranes, with the aim of increasing the contact surface with the phases of the membrane system. This paper presents the obtainment and characterization of a liquid membrane based on osmium nanoparticles (Os-NP) dispersed in ndecanol (nDol) for the realization of a membrane system with a large contact surface between the phases, but without using a liquid membrane support. The dispersion of osmium nanoparticles in n-decanol is carried out by the method of reducing osmium tetroxide with 1-undecenoic acid (UDA). The resulting membrane was characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy-dispersive spectroscopy analysis (EDAX), thermoanalysis (TG, DSC), Fourier transform infra-red (FTIR) spectroscopy and dynamic light scattering (DLS). In order to increase the mass transfer surface, a design for the membrane system was realized with the dispersion of the membrane through the receiving phase and the dispersion of the source phase through the membrane (DBLM-dispersion bulk liquid membrane). The process performance was tested for the reduction of p-nitrophenol (pNP) from the source phase, using sodium tetra-borohydride (NaBH4), to p-aminophenol (pAP), which was transported and collected in the receiving phase. The obtained results show that membranes based on the dispersion of osmium nanoparticles in n-decanol can be used with an efficiency of over 90% for the reduction of p-nitrophenol and the separation of p-aminophenol.

A Narrative Review of the Classical and Modern Diagnostic Methods of the No-Reflow Phenomenon.

The incidence of the no-reflow (NR) phenomenon varies depending on the diagnostic criteria used. If just the angiographic criteria are considered (i.e., a degree of thrombolysis in myocardial infarction ≤2), it will be found that the incidence of NR is quite low; on the other hand, when the myocardial NR is taken into account (i.e., a decrease in the quality of myocardial reperfusion expressed by the degree of myocardial blush), the real incidence is higher. Thus, the early establishment of a diagnosis of NR and the administration of specific treatment can lead to its reversibility. Otherwise, regardless of the follow-up period, patients with NR have a poor prognosis. In the present work, we offer a comprehensive perspective on diagnostic tools for NR detection, for improving the global management of patients with arterial microvasculature damage, which is a topic of major interest in the cardiology field, due to its complexity and its link with severe clinical outcomes.