Fluorescence-aided identification technique using a low-cost violet flashlight and rotatory instruments for dental trauma splint removal.

BACKGROUND/AIM: Removing resin composites used for bonding dental trauma splints may result in irreversible damage to the enamel. This in vitro study evaluated the influence of additional violet illumination and different bur types on damage caused to tooth enamel. MATERIALS AND METHODS: Fifteen maxillary models with four bovine incisor teeth were prepared. All models were scanned using a laboratory scanning system (s600 ARTI; Zirkonzahn). Six experimental groups (n = 10) were generated by two study factors: lighting type (three levels), (1) low-cost (5-7 US$) violet LED flashlight (LUATEK, LT 408); (2) VALO Cordless light curing unit (Ultradent) with black lens; or (3) without additional illumination; and rotatory instrument (two levels), (1) diamond bur or (2) multifluted tungsten-carbide bur. New scanning was performed after splint removal, and the generated files were superimposed on the initial scans using Cumulus software. The light emitted by both violet light sources was characterized by using integrating sphere and beam profile. A qualitative and quantitative analysis of enamel damage and two-way ANOVA followed by Tukey's post hoc was used at an α = 0.05. RESULTS: The use of low-cost violet flashlight that emitted the violet peak light at 385 nm and VALO Cordless with black lens at 396 nm resulted in significantly lower damage to the enamel surface than those in the groups without additional violet light (p < .001). An interaction between rotatory instruments and lighting was found. When no additional violet lighting was used, the diamond bur presented higher mean and maximum depth values. CONCLUSIONS: Fluorescence lighting facilitated the removal of remnant resin composite dental trauma splints, leading to less invasive treatment. The diamond bur resulted in higher enamel damage than that affected by the multifluted bur when no violet lighting was used. A low-cost violet flashlight is a useful fluorescence-aided identification technique for removing resin composite dental trauma splints.

Effect of four different mono and multi-wave light-curing units on the Knoop hardness of veneer resin composites.

OBJECTIVES: To evaluate the effect of mono and multi-wave light-curing units (LCUs) on the Knoop hardness of resin-based composites (RBC) that use different photoinitiators. METHODS: Central incisor-shaped specimens 12 mm long, 9 mm wide, and 1.5 mm thick were made from 2 RBCs that use different photoinitiators: Tetric N-Ceram (Ivoclar Vivadent) - and Vittra APS (FGM), both A2E shade. They were light-cured with 4 different LCUs: two claimed to be multi-wave - VALO Grand (Ultradent) and Emitter Now Duo (Schuster); and two were monowave - Radii Xpert (SDI) and Elipar DeepCure-L (3 M Oral Care) using 2 different light exposure protocols: one 40 s exposure centered over the specimen; and two 20 s light exposures that delivered light from two positions to better cover the entire tooth. 16 groups with 10 specimens in each group were made. The Knoop hardness (KH, kg/mm2) was measured at the top and bottom of the specimen in the center and at the cervical, incisal, mesial, and distal peripheral regions. The active tip diameters (mm) and spectral radiant powers (mW/nm) of the LCUs were measured with and without the interposition of the RBC, as well as the radiant exposure beam profiles (J/cm²) delivered to the top of the RBCs. The data was analyzed using Three-way ANOVA and Tukey's tests (α = 0.05). RESULTS: The VALO Grand (1029 mW) emitted twice the power of the Radii Xpert (500 mW). The KH values of VI and TN resin composite specimens were significantly affected by the LCU used (p < .001), the measurement location (p < .001), and the surface of the specimen (p < .001). LCUs with wider tip diameters produced greater Knoop hardness values at the peripheries of the 12 mm of long, 9 mm wide specimens. In general, the VALO Grand produced the highest KH values, followed by Elipar DeepCure-L, then by Radii Xpert. The Emitter Now Duo LCU produced the lowest values. Exposing the veneers from two locations reduced the differences between the LCUs and the effect of the measurement location. Only the VALO Grand could fully cover the composite veneer with light when the two locations were used. SIGNIFICANCE: The light tip must cover the entire restoration to photocure the RBC beneath the light tip.

Influence of non-carious cervical lesions, bone attachment level, and occlusal load on the stress distribution pattern in maxillary premolars: finite element analysis

This study aimed to evaluate the influence of different bone attachment levels and occlusal loads on the stress distribution pattern of maxillary premolars with or without non-carious cervical lesion (NCCL), before and after restoration with composite resin by three-dimensional (3D) finite element analysis. From the healthy model, NCCL models were produced and the cavity was restored with composite resin. Models with vertical and horizontal bone loss were also made. For each model, three types of occlusal loads were simulated (100 N): vertical load (VL), buccal load (BL), and palatal load (PL). After processing the models, the data were obtained in MPa for the criteria of Maximum Principal Stress (for all structures) and Minimum Principal Stress (for cortical and medullary bones). Stress values were collected for a node on the cervical buccal surface (Maximum Principal Stress) and the buccal crestal bone (Minimum Principal Stress). As a result, the different bone attachment levels did not affect stress distribution at the amelodentinal junction. The buccal load promoted a higher concentration of compressive stress on the buccal bone surface and the palatal load resulted in greater tensile stress in the buccal cervical third of the tooth. The concentration of tensile stress in the buccal cervical third was exacerbated by the presence of NCCL and it was similar to the healthy and restored models. It can be concluded that stress concentration at the bone level does not depend on the presence or absence of NCCL and the restoration procedure but it is related to the type of occlusal load. However, the presence of NCCL promoted a higher stress concentration in the cervical region, especially when combined with oblique occlusal loads.