Effects of Water and Different Solutes on Carbon-Nanotube Low-Voltage Field-Effect Transistors.

Semiconducting single-walled carbon nanotubes (swCNTs) are a promising class of materials for emerging applications. In particular, they are demonstrated to possess excellent biosensing capabilities, and are poised to address existing challenges in sensor reliability, sensitivity, and selectivity. This work focuses on swCNT field-effect transistors (FETs) employing rubbery double-layer capacitive dielectric poly(vinylidene fluoride-co-hexafluoropropylene). These devices exhibit small device-to-device variation as well as high current output at low voltages (<0.5 V), making them compatible with most physiological liquids. Using this platform, the swCNT devices are directly exposed to aqueous solutions containing different solutes to characterize their effects on FET current-voltage (FET I-V) characteristics. Clear deviation from ideal characteristics is observed when swCNTs are directly contacted by water. Such changes are attributed to strong interactions between water molecules and sp2 -hybridized carbon structures. Selective response to Hg2+ is discussed along with reversible pH effect using two distinct device geometries. Additionally, the influence of aqueous ammonium/ammonia in direct contact with the swCNTs is investigated. Understanding the FET I-V characteristics of low-voltage swCNT FETs may provide insights for future development of stable, reliable, and selective biosensor systems.

Biocompatible and totally disintegrable semiconducting polymer for ultrathin and ultralightweight transient electronics.

Increasing performance demands and shorter use lifetimes of consumer electronics have resulted in the rapid growth of electronic waste. Currently, consumer electronics are typically made with nondecomposable, nonbiocompatible, and sometimes even toxic materials, leading to serious ecological challenges worldwide. Here, we report an example of totally disintegrable and biocompatible semiconducting polymers for thin-film transistors. The polymer consists of reversible imine bonds and building blocks that can be easily decomposed under mild acidic conditions. In addition, an ultrathin (800-nm) biodegradable cellulose substrate with high chemical and thermal stability is developed. Coupled with iron electrodes, we have successfully fabricated fully disintegrable and biocompatible polymer transistors. Furthermore, disintegrable and biocompatible pseudo-complementary metal-oxide-semiconductor (CMOS) flexible circuits are demonstrated. These flexible circuits are ultrathin (<1 µm) and ultralightweight (∼2 g/m2) with low operating voltage (4 V), yielding potential applications of these disintegrable semiconducting polymers in low-cost, biocompatible, and ultralightweight transient electronics.

Highly Tunable and Facile Synthesis of Uniform Carbon Flower Particles.

Three-dimensional hierarchical porous carbon materials with flower-like superstructures are of great interest for energy applications since their unique shape not only provides high accessible surface area and consequently more exposed active sites but also facilitates ion transport for high-rate capability. However, finding a controllable way to make porous carbons with such specific shapes has been challenging. Herein, we report a tunable and simple method for one-pot synthesis of polyacrylonitrile and its copolymer nanostructured particles with various superstructures (flower, pompom, hairy leave, and petal shapes) controlled by employing various solvents or by the incorporation of different co-monomers. The correlation between polymer particle shapes and solvent properties has been identified through Hansen solubility parameters analysis. The obtained uniform polyacrylonitrile particles could be readily converted into porous carbons by high-temperature gas treatment while maintaining the original shape of the polymer precursor structures. The resulting carbon materials have high nitrogen-doping concentration (7-15 at%) and tunable porous structures. This novel synthetic method provides a simple way to make porous carbons with controllable morphology and potentially advantageous properties for a variety of potential energy and environmental applications, such as electrochemical energy conversion and wastewater treatment.

Stretchable Self-Healing Polymeric Dielectrics Cross-Linked Through Metal-Ligand Coordination.

A self-healing dielectric elastomer is achieved by the incorporation of metal-ligand coordination as cross-linking sites in nonpolar polydimethylsiloxane (PDMS) polymers. The ligand is 2,2'-bipyridine-5,5'-dicarboxylic amide, while the metal salts investigated here are Fe(2+) and Zn(2+) with various counteranions. The kinetically labile coordination between Zn(2+) and bipyridine endows the polymer fast self-healing ability at ambient condition. When integrated into organic field-effect transistors (OFETs) as gate dielectrics, transistors with FeCl2 and ZnCl2 salts cross-linked PDMS exhibited increased dielectric constants compared to PDMS and demonstrated hysteresis-free transfer characteristics, owing to the low ion conductivity in PDMS and the strong columbic interaction between metal cations and the small Cl(-) anions which can prevent mobile anions drifting under gate bias. Fully stretchable transistors with FeCl2-PDMS dielectrics were fabricated and exhibited ideal transfer characteristics. The gate leakage current remained low even after 1000 cycles at 100% strain. The mechanical robustness and stable electrical performance proved its suitability for applications in stretchable electronics. On the other hand, transistors with gate dielectrics containing large-sized anions (BF4(-), ClO4(-), CF3SO3(-)) displayed prominent hysteresis due to mobile anions drifting under gate bias voltage. This work provides insights on future design of self-healing stretchable dielectric materials based on metal-ligand cross-linked polymers.

Structural and electronic characterisation of π-extended tetrathiafulvalene derivatives as active components in field-effect transistors.

The electronic and structural properties of two tetrathiafulvalene derivatives bearing aromatic benzene rings are reported. Thin film transistors of these materials show p-type characteristics with comparable mobility values. It is found that the rigidification of the molecule is beneficial for reducing the reorganisation energy but also has an unfavorable impact on the electronic structure dimensionality.

Partially-Screened Field Effect and Selective Carrier Injection at Organic Semiconductor/Graphene Heterointerface.

Due to the lack of a bandgap, applications of graphene require special device structures and engineering strategies to enable semiconducting characteristics at room temperature. To this end, graphene-based vertical field-effect transistors (VFETs) are emerging as one of the most promising candidates. Previous work attributed the current modulation primarily to gate-modulated graphene-semiconductor Schottky barrier. Here, we report the first experimental evidence that the partially screened field effect and selective carrier injection through graphene dominate the electronic transport at the organic semiconductor/graphene heterointerface. The new mechanistic insight allows us to rationally design graphene VFETs. Flexible organic/graphene VFETs with bending radius <1 mm and the output current per unit layout area equivalent to that of the best oxide planar FETs can be achieved. We suggest driving organic light emitting diodes with such VFETs as a promising application.

Organic metal engineering for enhanced field-effect transistor performance.

A key device component in organic field-effect transistors (OFETs) is the organic semiconductor/metal interface since it has to ensure efficient charge injection. Traditionally, inorganic metals have been employed in these devices using conventional lithographic fabrication techniques. Metals with low or high work-functions have been selected depending on the type of semiconductor measured and, in some cases, the metal has been covered with molecular self-assembled monolayers to tune the work function, improve the molecular order at the interface and reduce the contact resistance. However, in the last few years, some approaches have been focused on utilizing organic metals in these devices, which have been fabricated by means of both evaporation and solution-processed techniques. Higher device performances have often been observed, which have been attributed to a range of factors, such as a more favourable organic/organic interface, a better matching of energy levels or/and to a reduction of the contact resistance. Further, in contrast to their inorganic counterparts, organic metals allow their chemical modification and thus the tuning of the Fermi level. In this perspective paper, an overview of the recent work devoted to the fabrication of OFETs with organic metals as electrodes will be carried out. It will be shown that in these devices not only is the matching of the HOMO or LUMO of the semiconductor with the metal work-function important, but other aspects such as the interface morphology can also play a critical role. Also, recent approaches in which the use of organic charge transfer salts as buffer layers at the metal contacts or on the dielectric or as doping agents of the organic semiconductors that have been used to improve the device performance will be briefly described.

A compact tetrathiafulvalene-benzothiadiazole dyad and its highly symmetrical charge-transfer salt: ordered donor π-stacks closely bound to their acceptors.

A compact and planar donor-acceptor molecule 1 comprising tetrathiafulvalene (TTF) and benzothiadiazole (BTD) units has been synthesised and experimentally characterised by structural, optical, and electrochemical methods. Solution-processed and thermally evaporated thin films of 1 have also been explored as active materials in organic field-effect transistors (OFETs). For these devices, hole field-effect mobilities of µFE = (1.3±0.5)×10(-3) and (2.7±0.4)×10(-3)  cm(2) V s(-1) were determined for the solution-processed and thermally evaporated thin films, respectively. An intense intramolecular charge-transfer (ICT) transition at around 495 nm dominates the optical absorption spectrum of the neutral dyad, which also shows a weak emission from its ICT state. The iodine-induced oxidation of 1 leads to a partially oxidised crystalline charge-transfer (CT) salt {(1)2I3}, and eventually also to a fully oxidised compound {1I3}⋅1/2I2. Single crystals of the former CT compound, exhibiting a highly symmetrical crystal structure, reveal a fairly good room temperature electrical conductivity of the order of 2 S cm(-1). The one-dimensional spin system bears compactly bonded BTD acceptors (spatial localisation of the LUMO) along its ridge.

HOMO stabilisation in π-extended dibenzotetrathiafulvalene derivatives for their application in organic field-effect transistors.

Three new organic semiconductors, in which either two methoxy units are directly linked to a dibenzotetrathiafulvalene (DB-TTF) central core and a 2,1,3-chalcogendiazole is fused on the one side, or four methoxy groups are linked to the DB-TTF, have been synthesised as active materials for organic field-effect transistors (OFETs). Their electrochemical behaviour, electronic absorption and fluorescence emission as well as photoinduced intramolecular charge transfer were studied. The electron-withdrawing 2,1,3-chalcogendiazole unit significantly affects the electronic properties of these semiconductors, lowering both the HOMO and LUMO energy levels and hence increasing the stability of the semiconducting material. The solution-processed single-crystal transistors exhibit high performance with a hole mobility up to 0.04 cm(2) V(-1) s(-1) as well as good ambient stability.

Stable Organic Radical for Enhancing Metal-Monolayer-Semiconductor Junction Performance.

The preparation of monolayers based on an organic radical and its diamagnetic counterpart has been pursued on hydrogen-terminated silicon surfaces. The functional monolayers have been investigated as solid-state metal/monolayer/semiconductor (MmS) junctions showing a characteristic diode behavior which is tuned by the electronic characteristics of the organic molecule. The eutectic gallium-indium liquid metal is used as a top electrode to perform the transport measurements and the results clearly indicate that the SOMO-SUMO molecular orbitals impact the device performance. The junction incorporating the radical shows an almost two orders of magnitude higher rectification ratio (R(|J1V/J-1V|) = 104.04) in comparison with the nonradical one (R(|J1V/J-1V|) = 102.30). The high stability of the fabricated MmS allows the system to be interrogated under irradiation, evidencing that at the wavelength where the photon energy is close to the band gap of the radical there is a clear enhancement of the photoresponse. This is translated into an increase of the photosensitivity (Sph) value from 68.7 to 269.0 mA/W for the nonradical and radical based systems, respectively.

Synergistic Effect of Solvent Vapor Annealing and Chemical Doping for Achieving High-Performance Organic Field-Effect Transistors with Ideal Electrical Characteristics.

Contact resistance and charge trapping are two key obstacles, often intertwined, that negatively impact on the performance of organic field-effect transistors (OFETs) by reducing the overall device mobility and provoking a nonideal behavior. Here, we expose organic semiconductor (OSC) thin films based on blends of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT-C8) with polystyrene (PS) to (i) a CH3CN vapor annealing process, (ii) a doping I2/water procedure, and (iii) vapors of I2/CH3CN to simultaneously dope and anneal the films. After careful analysis of the OFET electrical characteristics and by performing local Kelvin probe force microscopy studies, we found that the vapor annealing process predominantly reduces interfacial shallow traps, while the chemical doping of the OSC film is responsible for the diminishment of deeper traps and promoting a significant reduction of the contact resistance. Remarkably, the devices treated with I2/CH3CN reveal ideal electrical characteristics with a low level of shallow/deep traps and a very high and almost gate-independent mobility. Hence, this work demonstrates the promising synergistic effects of performing simultaneously a solvent vapor annealing and doping procedure, which can lead to trap-free OSC films with negligible contact resistance problems.

Emergent Insulator-Metal Transition with Tunable Optical and Electrical Gap in Thin Films of a Molecular Conducting Composite.

Composites exhibit unique synergistic properties emerging when components with different properties are combined. The tuning of the energy bandgap in the electronic structure of the material allows designing tailor-made systems with desirable mechanical, electrical, optical, and/or thermal properties. Here, we study an emergent insulator-metal transition at room temperature in bilayered (BL) thin-films comprised of polycarbonate/molecular-metal composites. Temperature-dependent resistance measurements allow monitoring of the electrical bandgap, which is in agreement with the optical bandgap extracted by optical absorption spectroscopy. The semiconductor-like properties of BL films, made with bis(ethylenedithio)-tetrathiafulvalene (BEDT-TTF or ET) α-ET2I3 (nano)microcrystals as two-dimensional molecular conductor on one side and insulator polycarbonate as a second ingredient, are attributed to an emergent phenomenon equivalent to the transition from an insulator to a metal. This made it possible to obtain semiconducting BL films with tunable electrical/optical bandgaps ranging from 0 to 2.9 eV. A remarkable aspect is the similarity close to room temperature of the thermal and mechanical properties of both composite components, making these materials ideal candidates to fabricate flexible and soft sensors for stress, pressure, and temperature aiming at applications in wearable human health care and bioelectronics.

Dielectric behavior of curcuminoid polymorphs on different substrates by direct soft vacuum deposition.

Our work examines the structural-electronic correlation of a new curcuminoid, AlkCCMoid, as a dielectric material on different substrates. For this purpose, we show a homemade sublimation method that allows the direct deposition of molecules on any type of matrix. The electronic properties of AlkCCMoid have been evaluated by measurements on single crystals, microcrystalline powder, and sublimated samples, respectively. GIWAXS studies on surfaces and XRD studies on powder have revealed the existence of polymorphs and the effect that substrates have on curcuminoid organization. We describe the dielectric nature of our system and identify how different polymorphs can affect electronic parameters such as permittivity, all corroborated by DFT calculations.

Benzodicarbomethoxytetrathiafulvalene derivatives as soluble organic semiconductors.

A series of new tetrathiafulvalene (TTF) derivatives bearing dimethoxycarbonyl and phenyl or phthalimidyl groups fused to the TTF core (6 and 15-18) has been synthesized as potential soluble semiconductor materials for organic field-effect transistors (OFETs). The electron-withdrawing substituents lower the energy of the HOMO and LUMO levels and increase the solubility and stability of the semiconducting material. Crystal structures of all new TTF derivatives are also described, and theoretical DFT calculations were carried out to study the potential of the crystals to be used in OFET. In the experimental study, the best performing device exhibited a hole mobility up to 7.5 × 10(-3) cm(2) V(-1) s(-1)).

Synthesis of 2D Porous Crystalline Materials in Simulated Microgravity.

To date, crystallization studies conducted in space laboratories, which are prohibitively costly and unsuitable to most research laboratories, have shown the valuable effects of microgravity during crystal growth and morphogenesis. Herein, an easy and highly efficient method is shown to achieve space-like experimentation conditions on Earth employing custom-made microfluidic devices to fabricate 2D porous crystalline molecular frameworks. It is confirmed that experimentation under these simulated microgravity conditions has unprecedented effects on the orientation, compactness and crack-free generation of 2D porous crystalline molecular frameworks as well as in their integration and crystal morphogenesis. It is believed that this work will provide a new "playground" to chemists, physicists, and materials scientists that desire to process unprecedented 2D functional materials and devices.

Low-Voltage, Dual-Gate Organic Transistors with High Sensitivity and Stability toward Electrostatic Biosensing.

High levels of performance and stability have been demonstrated for conjugated polymer thin-film transistors in recent years, making them promising materials for flexible electronic circuits and displays. For sensing applications, however, most research efforts have been focusing on electrochemical sensing devices. Here we demonstrate a highly stable biosensing platform using polymer transistors based on the dual-gate mechanism. In this architecture a sensing signal is transduced and amplified by the capacitive coupling between a low-k bottom dielectric and a high-k ionic elastomer top dielectric that is in contact with an analyte solution. The new design exhibits a high signal amplification, high stability under bias stress in various aqueous environments, and low signal drift. Our platform, furthermore, while responding expectedly to charged analytes such as the protein bovine serum albumin, is insensitive to changes of salt concentration of the analyte solution. These features make this platform a potentially suitable tool for a variety of biosensing applications.

Biodegradable and flexible arterial-pulse sensor for the wireless monitoring of blood flow.

The ability to monitor blood flow is critical to patient recovery and patient outcomes after complex reconstructive surgeries. Clinically available wired implantable monitoring technology requires careful fixation for accurate detection and needs to be removed after use. Here, we report the design of a pressure sensor, made entirely of biodegradable materials and based on fringe-field capacitor technology, for measuring arterial blood flow in both contact and non-contact modes. The sensor is operated wirelessly through inductive coupling, has minimal hysteresis, fast response times, excellent cycling stability, is highly robust, allows for easy mounting and eliminates the need for removal, thus reducing the risk of vessel trauma. We demonstrate the operation of the sensor with a custom-made artificial artery model and in vivo in rats. This technology may be advantageous in real-time post-operative monitoring of blood flow after reconstructive surgery.

A bioinspired flexible organic artificial afferent nerve.

The distributed network of receptors, neurons, and synapses in the somatosensory system efficiently processes complex tactile information. We used flexible organic electronics to mimic the functions of a sensory nerve. Our artificial afferent nerve collects pressure information (1 to 80 kilopascals) from clusters of pressure sensors, converts the pressure information into action potentials (0 to 100 hertz) by using ring oscillators, and integrates the action potentials from multiple ring oscillators with a synaptic transistor. Biomimetic hierarchical structures can detect movement of an object, combine simultaneous pressure inputs, and distinguish braille characters. Furthermore, we connected our artificial afferent nerve to motor nerves to construct a hybrid bioelectronic reflex arc to actuate muscles. Our system has potential applications in neurorobotics and neuroprosthetics.

Deformable Organic Nanowire Field-Effect Transistors.

Deformable electronic devices that are impervious to mechanical influence when mounted on surfaces of dynamically changing soft matters have great potential for next-generation implantable bioelectronic devices. Here, deformable field-effect transistors (FETs) composed of single organic nanowires (NWs) as the semiconductor are presented. The NWs are composed of fused thiophene diketopyrrolopyrrole based polymer semiconductor and high-molecular-weight polyethylene oxide as both the molecular binder and deformability enhancer. The obtained transistors show high field-effect mobility >8 cm2 V-1 s-1 with poly(vinylidenefluoride-co-trifluoroethylene) polymer dielectric and can easily be deformed by applied strains (both 100% tensile and compressive strains). The electrical reliability and mechanical durability of the NWs can be significantly enhanced by forming serpentine-like structures of the NWs. Remarkably, the fully deformable NW FETs withstand 3D volume changes (>1700% and reverting back to original state) of a rubber balloon with constant current output, on the surface of which it is attached. The deformable transistors can robustly operate without noticeable degradation on a mechanically dynamic soft matter surface, e.g., a pulsating balloon (pulse rate: 40 min-1 (0.67 Hz) and 40% volume expansion) that mimics a beating heart, which underscores its potential for future biomedical applications.

Mechanochemical unzipping of insulating polyladderene to semiconducting polyacetylene.

Biological systems sense and respond to mechanical stimuli in a complex manner. In an effort to develop synthetic materials that transduce mechanical force into multifold changes in their intrinsic properties, we report on a mechanochemically responsive nonconjugated polymer that converts to a conjugated polymer via an extensive rearrangement of the macromolecular structure in response to force. Our design is based on the facile mechanochemical unzipping of polyladderene, a polymer inspired by a lipid natural product structure and prepared via direct metathesis polymerization. The resultant polyacetylene block copolymers exhibit long conjugation length and uniform trans-configuration and self-assemble into semiconducting nanowires. Calculations support a tandem unzipping mechanism of the ladderene units.