Non-woven PGA/PVA fibrous mesh as an appropriate scaffold for chondrocyte proliferation.

Non-woven textile mesh from polyglycolic acid (PGA) was found as a proper material for chondrocyte adhesion but worse for their proliferation. Neither hyaluronic acid nor chitosan nor polyvinyl alcohol (PVA) increased chondrocyte adhesion. However, chondrocyte proliferation suffered from acidic byproducts of PGA degradation. However, the addition of PVA and/or chitosan into a wet-laid non-woven textile mesh from PGA improved chondrocyte proliferation seeded in vitro on the PGA-based composite scaffold namely due to a diminished acidification of their microenvironment. This PVA/PGA composite mesh used in combination with a proper hydrogel minimized the negative effect of PGA degradation without dropping positive parameters of the PGA wet-laid non-woven textile mesh. In fact, presence of PVA and/or chitosan in the PGA-based wet-laid non-woven textile mesh even advanced the PGA-based wet-laid non-woven textile mesh for chondrocyte seeding and artificial cartilage production due to a positive effect of PVA in such a scaffold on chondrocyte proliferation.

Dynamic creep properties of a novel nanofiber hernia mesh in abdominal wall repair.

PURPOSE: Incisional hernia is the most common complication following abdominal surgery. While mesh repair is common, none of the current meshes mimic the physiology of the abdominal wall. This study compares suture only repair with polypropylene mesh and a prototype of a novel implant (poly-epsilon-caprolactone nanofibers) and their influence on the physiology of an abdominal wall in an animal model. METHODS: 27 Chinchilla rabbits were divided into six groups based on the type of the implant. Midline abdominal incision was repaired using one of the compared materials with suture alone serving as the control. 6 weeks post-surgery animals were killed and their explanted abdominal wall subjected to biomechanical testing. RESULTS: Both-hysteresis and maximum strength curves showed high elasticity and strength in groups where the novel implant was used. Polypropylene mesh proved as stiff and fragile compared to other groups. CONCLUSION: Poly-epsilon-caprolactone nanofiber scaffold is able to improve the dynamic properties of healing fascia with no loss of maximum tensile strength when compared to polypropylene mesh in an animal model.

Composite 3D printed scaffold with structured electrospun nanofibers promotes chondrocyte adhesion and infiltration.

Additive manufacturing, also called 3D printing, is an effective method for preparing scaffolds with defined structure and porosity. The disadvantage of the technique is the excessive smoothness of the printed fibers, which does not support cell adhesion. In the present study, a 3D printed scaffold was combined with electrospun classic or structured nanofibers to promote cell adhesion. Structured nanofibers were used to improve the infiltration of cells into the scaffold. Electrospun layers were connected to 3D printed fibers by gluing, thus enabling the fabrication of scaffolds with unlimited thickness. The composite 3D printed/nanofibrous scaffolds were seeded with primary chondrocytes and tested in vitro for cell adhesion, proliferation and differentiation. The experiment showed excellent cell infiltration, viability, and good cell proliferation. On the other hand, partial chondrocyte dedifferentiation was shown. Other materials supporting chondrogenic differentiation will be investigated in future studies.

The combination of nanofibrous and microfibrous materials for enhancement of cell infiltration and in vivo bone tissue formation.

Fibrous scaffolds are desired in tissue engineering applications for their ability to mimic extracellular matrix. In this study we compared fibrous scaffolds prepared from polycaprolactone using three different fabrication methods, electrospinning (ES), electro-blowing and melt-blown combined with ES. Scaffolds differed in morphology, fiber diameters and pore sizes. Mesenchymal stem cell adhesion, proliferation and osteogenic differentiation on scaffolds was evaluated. The most promising scaffold was shown to be melt-blown in combination with ES which combined properties of both technologies. Microfibers enabled good cell infiltration and nanofibers enhanced cell adhesion. This scaffold was used for further testing in critical sized defects in rabbits. New bone tissue formation occurred from the side of the treated defects, compared to a control group where only fat tissue was present. Polycaprolactone fibrous scaffold prepared using a combination of melt-blown and ES technology seems to be promising for bone regeneration. The practical application of results is connected with enormous production capacity and low cost of materials produced by melt-blown technology, compared to other bone scaffold fabrication methods.

Collagen/hydroxyapatite scaffold enriched with polycaprolactone nanofibers, thrombocyte-rich solution and mesenchymal stem cells promotes regeneration in large bone defect in vivo.

A three-dimensional scaffold of type I collagen and hydroxyapatite enriched with polycaprolactone nanofibers (Coll/HA/PCL), autologous mesenchymal stem cells (MSCs) in osteogenic media, and thrombocyte-rich solution (TRS) was an optimal implant for bone regeneration in vivo in white rabbits. Nanofibers optimized the viscoelastic properties of the Coll/HA scaffold for bone regeneration. MSCs and TRS in the composite scaffold improved bone regeneration. Three types of Coll/HA/PCL scaffold were prepared: an MSC-enriched scaffold, a TRS-enriched scaffold, and a scaffold enriched with both MSCs and TRS. These scaffolds were implanted into femoral condyle defects 6 mm in diameter and 10-mm deep. Untreated defects were used as a control. Macroscopic and histological analyses of the regenerated tissue from all groups were performed 12 weeks after implantation. The highest volume and most uniform distribution of newly formed bone occurred in defects treated with scaffolds enriched with both MSCs and TRS compared with that in defects treated with scaffolds enriched by either component alone. The modulus of elasticity in compressive testing was significantly higher in the Coll/HA/PCL scaffold than those without nanofibers. The composite Coll scaffold functionalized with PCL nanofibers and enriched with MSCs and TRS appears to be a novel treatment for bone defects.

Optimized conditions for mesenchymal stem cells to differentiate into osteoblasts on a collagen/hydroxyapatite matrix.

Collagen/hydroxyapatite (HA) composite scaffolds are known to be suitable scaffolds for seeding with mesenchymal stem cells (MSCs) differentiated into osteoblasts and for the in vitro production of artificial bones. However, the optimal collagen/HA ratio remains unclear. Our study confirmed that a higher collagen content increased scaffold stiffness but that a greater stiffness was not sufficient for bone tissue formation, a complex process evidently also dependent on scaffold porosity. We found that the scaffold pore diameter was dependent on the concentration of collagen and HA and that it could play a key role in cell seeding. In conclusion, the optimal scaffold for new bone formation and cell proliferation was found to be a composite scaffold formed from 50 wt % HA in 0.5 wt % collagen I solution.