RESUMEN
In this article, we compare two different kinds of commercial light-emitting diodes (LEDs) in transmission and organic photodetectors based on poly(3-hexylthiophene) (P3HT) and a phenyl-C61-butyric acid methyl ester (PCBM) blend used as active layer in reception. Photovoltaic cells based on massive heterojunctions of semiconductor polymers have focused the attention of researchers due to their several potential advantages over their inorganic counterparts, such as their simplicity, low cost, and ability to process large area devices, even on flexible substrates. Furthermore, in logistics, storage management systems require the implementation of technological solutions that allow the control of merchandise in real time by means of light-emitting diode signals that send information about the product. However, the slow response time of these organic photodetectors should not be critical for this application, where the light intensity changes are very slow, which limits the speed of data transmission compared to inorganic based systems that use wireless optical communications. Finally, we show a low-cost visible light communication system based on organic photodetectors with a frame based on on-off keying with Manchester encoding to support device-to-device connections.
RESUMEN
The energy sector is a major contributor to global greenhouse gas emissions, necessitating a transition to renewable energy sources. The photovoltaic industry plays a crucial role in this transition by harnessing solar energy, a clean and abundant resource. However, the high cost of solar panels remains a challenge. Organic solar cells (OSCs) offer a promising alternative to conventional silicon-based cells due to their low production costs and flexibility. In this study, we focus on optimizing the performance of OSCs by investigating the influence of solvent volume in the hole transport layer. By gradually increasing the volume of dimethylformamide (DMF), dimethyl sulfoxide (DMSO), and tetrahydrofuran (THF) in the PEDOT:PSS layer, we analyse the impact on power conversion efficiency (PCE) and assess the economic and environmental implications. Our results demonstrate the potential for enhancing the PCE of OSCs through solvent optimization, thereby advancing the greening of the photovoltaic industry while considering economic viability and environmental sustainability.
RESUMEN
In this study, poly(9-vinylcarbazole) (PVK)-based LEDs doped with reduced graphene oxide (rGO) and cadmium sulphide (CdS) nanocrystals were fabricated by spin-coating. The hybrid LED structure was a layer sequence of glass/indium tin oxide (ITO)/PEDOT:PSS|rGO/PVK/Al. rGO was included in the poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) layer due to its energy bands being close to PEDOT:PSS bands, and the possibility of using water for dispersing both polymer and flakes. Optical properties such as photoluminescence and UV-Vis absorption were not affected by the addition of rGO to the PEDOT:PSS solution. However, PVK-based LEDs with rGO showed increased current density compared to those without rGO in the hole transporting layer. Higher electroluminescence intensities were observed for rGO-enriched LEDs, although the shape of the spectrum was not modified. LEDs including CdS nanocrystals in the poly(9-vinylcarbazole) emissive layer did not show such dependence on the rGO presence. Though the addition of rGO to PEDOT:PSS still produces a slightly higher current density in CdS doped LEDs, this growth is no longer proportional to the rGO load.
RESUMEN
Immiscibility between dimethyl sulfoxide (DMSO) and polar solvents used for poly(N-vinylcarbazole) (PVK) solutions, leads to failed light-emitting diodes when colloidal cadmium sulfide (CdS) nanoparticles capped with thiophenol are incorporated to their active layer. To prevent this, a heat treatment is applied to the CdS nanoparticles in order to evaporate DMSO solvent. After evaporation most of the nanoparticles increased their size, and some of them show hexagonal crystalline structure instead of the original cubic zinc-blende observed in colloidal pre-treated nanoparticles. Nevertheless, enhanced electronic properties are measured in light-emitting devices when DMSO-free nanoparticles are embedded in the poly(N-vinylcarbazole) active layer. Light emission from these hybrid devices comprises the whole visible range of wavelengths as searched for white LEDs. Moreover, electroluminescence from both types of CdS nanoparticles (smaller cubic and bigger hexagonal) has been discriminated and interpreted through Gaussian deconvolution.