Ecologically sustainable removal of pharmaceuticals: A mechanistic study of bismuth sulfide-graphene oxide/silver nanocomposite.

Bismuth sulfide nanoparticles (BiS NPs) were synthesized via the hydrothermal method, and reduced graphene oxide(rGO) and silver nanoparticles (Ag), which acted as substrates, have prepared using the chemical reduction method. The synthesized nanoparticles have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet-visible spectroscopy, and photoluminescence spectroscopy. Commercially available paracetamol-500 mg (PAM) and aspirin-300 mg (ASP) were selected for photodegradation under visible light using the as-prepared composites in an aqueous solution. Photoluminescence spectroscopy was used to detect PAM and ASP using the photo-excited electron transfer (PET) process, and the limit of detection (LOD) has obtained for PAM(8.70 ppm) and ASP(4.43 ppm) with a sensitivity of 0.9954 and 0.8002, respectively. Fourier transform infrared spectroscopy (FTIR) was used to analyze the before and after degradation products and to confirm the disintegrated products such as -COOH and -CH- both before and after disintegration.. The experimental data were found to fit well with the Freundlich isotherm, suggesting that the as-prepared nanocomposites exhibited a heterogeneous nature for PAM (5119 mg/L), and the pseudo-first-order kinetic model suggests ASP (1030 mg/L) with R2 values of 0.9119 and 0.7075. The risk assessment analysis of PAM was 9.823 µg/L(RQ > 1) and that of ASP was 0.2106 µg/L(RQ < 1), indicating that PAM has a higher potential risk than ASP. The demographic data of the participants indicated that PAM was the most stockpiled medicine at home; this work also encompasses the action of a single PAM and ASP tablet toward the environment, if it is accidently disposed of improperly could create massive water/soil pollution; hence, the care/duty of each person should follow the proper disposal of medical waste because we cannot replace this environment.

Nucleic acid-based electrochemical biosensors for rapid clinical diagnosis: advances, challenges, and opportunities.

Clinical diagnostic tests should be quick, reliable, simple to perform, and affordable for diagnosis and treatment of diseases. In this regard, owing to their novel properties, biosensors have attracted the attention of scientists as well as end-users. They are efficient, stable, and relatively cheap. Biosensors have broad applications in medical diagnosis, including point-of-care (POC) monitoring, forensics, and biomedical research. The electrochemical nucleic acid (NA) biosensor, the latest invention in this field, combines the sensitivity of electroanalytical methods with the inherent bioselectivity of deoxyribonucleic acid (DNA) and ribonucleic acid (RNA). The NA biosensor exploits the affinity of single-stranded DNA/RNA for its complementary strand and is used to detect complementary sequences of NA based on hybridization. After the NA component in the sensor detects the analyte, a catalytic reaction or binding event that generates an electrical signal in the transducer ensues. Since 2000, much progress has been made in this field, but there are still numerous challenges. This critical review describes the advances, challenges, and prospects of NA-based electrochemical biosensors for clinical diagnosis. It includes the basic principles, classification, sensing enhancement strategies, and applications of biosensors as well as their advantages, limitations, and future prospects, and thus it should be useful to academics as well as industry in the improvement and application of EC NA biosensors.

Current trends in polymerase chain reaction based detection of three major human pathogenic vibrios.

Vibrio parahaemolyticus, Vibrio cholerae and Vibrio vulnificus are the most significant aquatic pathogens of the genera Vibrio, account for most Vibrio-associated outbreaks worldwide. Rapid identification of these pathogens is of great importance for disease surveillance, outbreak investigations and food safety maintenance. Traditional culture dependent methods are time-consuming and labor-intensive whereas culture-independent polymerase chain reaction (PCR) based assays are reliable, consistent, rapid and reproducible. This review covers the recent development and applications of PCR based techniques, which have accelerated advances in the analysis of nucleic acids to identify three major pathogenic vibrios. Emphasis has been given to analytical approaches as well as advantages and limits of the available methods. Overall, this review article possesses the substantial merit to be used as a reference guide for the researchers to develop improved PCR based techniques for the differential detection and quantification of Vibrio species.

Authentication of Halal and Kosher meat and meat products: Analytical approaches, current progresses and future prospects.

Meat and meat products are widely consumed worldwide as a source of high-quality proteins, essential amino acids, vitamins, and necessary minerals. The acceptability of Halal and Kosher meat products relies not only on the species origin but also on the manner of slaughtering of animals. Both Islam and Judaism have their own dietary laws in their holy books regarding acceptance and forbiddance of dietary items particularly meat and meat products. They also include many strictures to follow for ritual cleanliness of foods. Since the authenticity of Halal and Kosher food created increased concerns among consumers, the integrity of Halal and Kosher meat and meat products must be assured so that consumers can be accomplished with the originality of products. There is an increasing demand for reliable and sensitive techniques for the authentication of various Halal and Kosher meat products. This up-to-date review intends to provide an updated and extensive overview critically on the present situation, progress, and challenges of analytical techniques to authenticate animal species in meat items. It also addresses slaughtering procedure with brief discussion on Halal and Kosher laws with a view to creating consumer awareness against fraudulent practices. The available methods are schematically presented, and their salient features are comparatively elucidated in tables. Potential future technologies are predicted, and probable challenges are summarized. Overall, the present review article possesses substantial merits to be served as a reference guide in the field of academia and industry for the preparation/processing and identification of Halal and Kosher meat and meat products as well as may act as a platform to help improve existing authentication methods.

Nanocomposite of Nickel Nanoparticles-Impregnated Biochar from Palm Leaves as Highly Active and Magnetic Photocatalyst for Methyl Violet Photocatalytic Oxidation.

Photocatalysis has been recognized as a feasible method in water and wastewater treatment. Compared to other methods such as adsorption and chemical oxidation, the use of photocatalyst in the advanced oxidation processes gives benefits such as a longer lifetime of the catalyst and less consumable chemicals. Currently, explorations into low-cost, effective photocatalysts for organic contaminated water are being developed. Within this scheme, an easily separated photocatalyst with other functionality, such as high adsorption, is important. In this research, preparation of a magnetic nanocomposite photocatalyst based on agricultural waste, palm leaves biochar impregnated nickel nanoparticles (Ni/BC), was investigated. The nanocomposite was prepared by direct pyrolysis of palm leaves impregnated with nickel (II) chloride precursor. Furthermore, the physicochemical characterization of the material was performed by using an X-ray diffractometer (XRD), scanning electron microscopy-energy dispersive X-ray fluorescence (SEM-EDX), transmission electron microscopy (TEM), gas sorption analysis, X-ray photoelectron spectroscopy (XPS) and vibrating sample magnetometer (VSM). The photocatalytic activity of Ni/BC was evaluated for methyl violet (MV) photocatalytic oxidation. The results from XRD, XPS and TEM analyses identified single nickel nanoparticles dispersed on the biochar structure ranging from 30-50 nm in size. The dispersed nickel nanoparticles increased the BET specific surface area of biochar from 3.92 m2/g to 74.12 m2/g oxidation. High photocatalytic activity of the Ni/BC was exhibited by complete MV removal in 30 min for the concentration ranging from 10-80 mg/L. In addition, the Ni/BC showed stability in the pH range of 4-10 and reusability without any activity change until fifth usage. The separable photocatalyst is related to magnetism of about 13.7 emu/g. The results highlighted the role of biochar as effective support for Ni as photoactive material.

A Review on Recent Progress of Stingless Bee Honey and Its Hydrogel-Based Compound for Wound Care Management.

Stingless bee honey has a distinctive flavor and sour taste compared to Apis mellifera honey. Currently, interest in farming stingless bees is growing among rural residents to meet the high demand for raw honey and honey-based products. Several studies on stingless bee honey have revealed various therapeutic properties for wound healing applications. These include antioxidant, antibacterial, anti-inflammatory, and moisturizing properties related to wound healing. The development of stingless bee honey for wound healing applications, such as incorporation into hydrogels, has attracted researchers worldwide. As a result, the effectiveness of stingless bee honey against wound infections can be improved in the future to optimize healing rates. This paper reviewed the physicochemical and therapeutic properties of stingless bee honey and its efficacy in treating wound infection, as well as the incorporation of stingless bee honey into hydrogels for optimized wound dressing.

Advancements in Detection Approaches of Severe Acute Respiratory Syndrome Coronavirus 2.

Diagnostic testing to identify individuals infected with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) plays a key role in selecting appropriate treatments, saving people's lives and preventing the global pandemic of COVID-19. By testing on a massive scale, some countries could successfully contain the disease spread. Since early viral detection may provide the best approach to curb the disease outbreak, the rapid and reliable detection of coronavirus (CoV) is therefore becoming increasingly important. Nucleic acid detection methods, especially real-time reverse transcription polymerase chain reaction (RT-PCR)-based assays are considered the gold standard for COVID-19 diagnostics. Some non-PCR-based molecular methods without thermocycler operation, such as isothermal nucleic acid amplification have been proved promising. Serologic immunoassays are also available. A variety of novel and improved methods based on biosensors, Clustered-Regularly Interspaced Short Palindromic Repeats (CRISPR) technology, lateral flow assay (LFA), microarray, aptamer etc. have also been developed. Several integrated, random-access, point-of-care (POC) molecular devices are rapidly emerging for quick and accurate detection of SARS-CoV-2 that can be used in the local hospitals and clinics. This review intends to summarize the currently available detection approaches of SARS-CoV-2, highlight gaps in existing diagnostic capacity, and propose potential solutions and thus may assist clinicians and researchers develop better technologies for rapid and authentic diagnosis of CoV infection.

Bone tissue engineering potentials of 3D printed magnesium-hydroxyapatite in polylactic acid composite scaffolds.

The primary role of bone tissue engineering is to reconcile the damaged bones and facilitate the speedy recovery of the injured bones. However, some of the investigated metallic implants suffer from stress-shielding, palpability, biocompatibility, etc. Consequently, the biodegradable scaffolds fabricated from polymers have gathered much attention from researchers and thus helped the tissue engineering sector by providing many alternative materials whose functionality is similar to that of natural bones. Herein, we present the fabrication and testing of a novel composite, magnesium (Mg)-doped hydroxyapatite (HAp) glazed onto polylactic acid (PLA) scaffolds where polyvinyl alcohol (PVA) used as a binder. For the composite formation, Creality Ender-3 pro High Precision 3D Printer with Shape tool 3D Technology on an FSD machine operated by Catia design software was employed. The composite has been characterized for the crystallinity (XRD), surface functionality (FTIR), morphology (FESEM), biocompatibility (hemolytic and protein absorption), and mechanical properties (stress-strain and maximum compressive strength). The powder XRD analysis confirmed the semicrystalline nature and intact structure of HAp even after doping with Mg, while FTIR studies for the successful formation of Mg-HAp/PVA@PLA composite. The FESEM provided analysis indicated for the 3D porous architecture and well-defined morphology to efficiently transport the nutrients, and the biocompatibility studies are supporting that the composite for blood compatible with the surface being suitable enough for the protein absorption. Finally, the composite's antibacterial activity (against Staphylococcus aureus and Escherichia coli) and the test of mechanical properties supported for the enhanced inhibition of active growth of microorganisms and maximum compressive strength, respectively. Based on the research outcomes of biocompatibility, antibacterial activity, and mechanical resistance, the fabricated Mg-HAp/PVA@PLA composite suits well as a promising biomaterial platform for orthopedic applications by functioning towards the open reduction internal fixation of bone fractures and internal repairs.

Design and Analysis of Soft Error Rate in FET/CNTFET Based Radiation Hardened SRAM Cell.

Aerospace equipages encounter potential radiation footprints through which soft errors occur in the memories onboard. Hence, robustness against radiation with reliability in memory cells is a crucial factor in aerospace electronic systems. This work proposes a novel Carbon nanotube field-effect transistor (CNTFET) in designing a robust memory cell to overcome these soft errors. Further, a petite driver circuit to test the SRAM cells which serve the purpose of precharge and sense amplifier, and has a reduction in threefold of transistor count is recommended. Additionally, analysis of robustness against radiation in varying memory cells is carried out using standard GPDK 90 nm, GPDK 45 nm, and 14 nm CNTFET. The reliability of memory cells depends on the critical charge of a device, and it is tested by striking an equivalent current charge of the cosmic ray's linear energy transfer (LET) level. Also, the robustness of the memory cell is tested against the variation in process, voltage and temperature. Though CNTFET surges with high power consumption, it exhibits better noise margin and depleted access time. GPDK 45 nm has an average of 40% increase in SNM and 93% reduction of power compared to the 14 nm CNTFET with 96% of surge in write access time. Thus, the conventional MOSFET's 45 nm node outperforms all the configurations in terms of static noise margin, power, and read delay which swaps with increased write access time.

Adsorption Studies of Volatile Organic Compound (Naphthalene) from Aqueous Effluents: Chemical Activation Process Using Weak Lewis Acid, Equilibrium Kinetics and Isotherm Modelling.

This study deals with the preparation of activated carbon (CDSP) from date seed powder (DSP) by chemical activation to eliminate polyaromatic hydrocarbon-PAHs (naphthalene-C10H8) from synthetic wastewater. The chemical activation process was carried out using a weak Lewis acid of zinc acetate dihydrate salt (Zn(CH3CO2)2·2H2O). The equilibrium isotherm and kinetics analysis was carried out using DSP and CDSP samples, and their performances were compared for the removal of a volatile organic compound-naphthalene (C10H8)-from synthetic aqueous effluents or wastewater. The equilibrium isotherm data was analyzed using the linear regression model of the Langmuir, Freundlich and Temkin equations. The R2 values for the Langmuir isotherm were 0.93 and 0.99 for naphthalene (C10H8) adsorption using DSP and CDSP, respectively. CDSP showed a higher equilibrium sorption capacity (qe) of 379.64 µg/g. DSP had an equilibrium sorption capacity of 369.06 µg/g for C10H8. The rate of reaction was estimated for C10H8 adsorption using a pseudo-first order, pseudo-second order and Elovich kinetic equation. The reaction mechanism for both the sorbents (CDSP and DSP) was studied using the intraparticle diffusion model. The equilibrium data was well-fitted with the pseudo-second order kinetics model showing the chemisorption nature of the equilibrium system. CDSP showed a higher sorption performance than DSP due to its higher BET surface area and carbon content. Physiochemical characterizations of the DSP and CDSP samples were carried out using the BET surface area analysis, Fourier-scanning microscopic analysis (FSEM), energy-dispersive X-ray (EDX) analysis and Fourier-transform spectroscopic analysis (FTIR). A thermogravimetric and ultimate analysis was also carried out to determine the carbon content in both the sorbents (DSP and CDSP) here. This study confirms the potential of DSP and CDSP to remove C10H8 from lab-scale synthetic wastewater.

Biomass derived green carbon dots for sensing applications of effective detection of metallic contaminants in the environment.

The rapid consumption of metals and unorganized disposal have led to unprecedented increases in heavy metal ion concentrations in the ecosystem, which disrupts environmental homeostasis and results in agricultural biodiversity loss. Mitigation and remediation plans for heavy metal pollution are largely dependent on the discovery of cost-effective, biocompatible, specific, and robust detectors because conventional methods involve sophisticated electronics and sample preparation procedures. Carbon dots (CDs) have gained significant importance in sensing applications related to environmental sustainability. Fluorescence sensor applications have been enhanced by their distinctive spectral properties and the potential for developing efficient photonic devices. With the recent development of biomass-functionalized carbon dots, a wide spectrum of multivalent and bivalent transition metal ions responsible for water quality degradation can be detected with high efficiency and minimal toxicity. This review explores the various methods of manufacturing carbon dots and the biochemical mechanisms involved in metal detection using green carbon dots for sensing applications involving Cu (II), Fe (III), Hg (II), and Cr (VI) ions in aqueous systems. A detailed discussion of practical challenges and future recommendations is presented to identify feasible design routes.

Sensor to Electronics Applications of Graphene Oxide through AZO Grafting.

Graphene is a two-dimensional (2D) material with a single atomic crystal structure of carbon that has the potential to create next-generation devices for photonic, optoelectronic, thermoelectric, sensing, wearable electronics, etc., owing to its excellent electron mobility, large surface-to-volume ratio, adjustable optics, and high mechanical strength. In contrast, owing to their light-induced conformations, fast response, photochemical stability, and surface-relief structures, azobenzene (AZO) polymers have been used as temperature sensors and photo-switchable molecules and are recognized as excellent candidates for a new generation of light-controllable molecular electronics. They can withstand trans-cis isomerization by conducting light irradiation or heating but have poor photon lifetime and energy density and are prone to agglomeration even at mild doping levels, reducing their optical sensitivity. Graphene derivatives, including graphene oxide (GO) and reduced graphene oxide (RGO), are an excellent platform that, combined with AZO-based polymers, could generate a new type of hybrid structure with interesting properties of ordered molecules. AZO derivatives may modify the energy density, optical responsiveness, and photon storage capacity, potentially preventing aggregation and strengthening the AZO complexes. They are potential candidates for sensors, photocatalysts, photodetectors, photocurrent switching, and other optical applications. This review aimed to provide an overview of the recent progress in graphene-related 2D materials (Gr2MS) and AZO polymer AZO-GO/RGO hybrid structures and their synthesis and applications. The review concludes with remarks based on the findings of this study.

The development of ZnO nanoparticle-embedded graphitic-carbon nitride towards triple-negative breast cancer therapy.

The present study deals with the effects of curcumin-loaded ZnO nanoparticles (NPs) embedded in graphitic-carbon nitride (g-C3N4) sheets for breast cancer cells. The synthesis of these sheets was carried out by a simple co-precipitation method. The physicochemical and thermal properties of the composite sheets were studied using various characterization techniques. The powder X-ray diffraction and high-resolution transmission electron microscopy analyses confirmed the hexagonal wurtzite phase of the ZnO nanoparticles, which were randomly distributed on the g-C3N4 nanosheets, generating a finely bonded interface between the two components. The X-ray photoelectron spectroscopy analysis confirmed the successful formation of the g-C3N4@ZnO composite, while the thermal studies revealed the thermal stability of the composite. In addition, the drug release and kinetics studies proved that the release of curcumin was more significant under acidic conditions (pH 5) compared with neutral pH (7.4). Further, the biological assays verified the antibacterial activity (against two different cultures of E. coli and S. aureus) and anticancer activity (against MDA-MB-231 cancer cells) of the g-C3N4@ZnO/C nanocomposite. Finally, the lactate dehydrogenase activity assay presented the cytotoxic assessment of the nanocomposite based on its cytoplasmic activity and the extent of enzymes released from the damaged cells.

Z-scheme NiO/g-C3N4 nanocomposites prepared using phyto-mediated nickel nanoparticles for the efficient photocatalytic degradation.

Highly-effective photocatalyst of NiO/g-C3N4 with was successfully synthesized by using phyto-mediated-synthesized nickel nanoparticles. The preparation was initiated by synthesizing nickel nanoparticles by using Tinosphora cordifolia stem extract under ultrasound-assisted method followed by the dispersing onto g-C3N4 structure. The study focused on physicochemical characterization and photocatalytic activity as function of the percentage of Ni in the nanocomposite. The photocatalytic activity examinations were carried out to rhodamine B and tetracycline photocatalytic oxidation. The results demonstrated that graphitic carbon nitride is effectively improved the photocatalytic activity of NiO for both photocatalytic oxidation reactions. From the varied Ni content of 5; 10; and 20 %wt., it was also found that the highest photoactivity was achieved by the composite having 10 %wt. of nickel content. The high effectivity was showed by degradation efficiency of 95% toward Rhodamine B and 98% toward tetracycline. The examination on effect of scavengers suggests that Z-scheme involved in the photocatalytic mechanism which facilitated the efficient separation of the photogenerated electron-hole pairs under visible light illumination. In summary, the present findings provide a green approach for fabricating the effective photocatalysts for organic contaminant degradation.

Recent Progress on Functionalized Graphene Quantum Dots and Their Nanocomposites for Enhanced Gas Sensing Applications.

Gas-sensing technology has witnessed significant advancements that have been driven by the emergence of graphene quantum dots (GQDs) and their tailored nanocomposites. This comprehensive review surveys the recent progress made in the construction methods and applications of functionalized GQDs and GQD-based nanocomposites for gas sensing. The gas-sensing mechanisms, based on the Fermi-level control and charge carrier depletion layer theory, are briefly explained through the formation of heterojunctions and the adsorption/desorption principle. Furthermore, this review explores the enhancements achieved through the incorporation of GQDs into nanocomposites with diverse matrices, including polymers, metal oxides, and 2D materials. We also provide an overview of the key progress in various hazardous gas sensing applications using functionalized GQDs and GQD-based nanocomposites, focusing on key detection parameters such as sensitivity, selectivity, stability, response and recovery time, repeatability, and limit of detection (LOD). According to the most recent data, the normally reported values for the LOD of various toxic gases using GQD-based sensors are in the range of 1-10 ppm. Remarkably, some GQD-based sensors exhibit extremely low detection limits, such as N-GQDs/SnO2 (0.01 ppb for formaldehyde) and GQD@SnO2 (0.10 ppb for NO2). This review provides an up-to-date perspective on the evolving landscape of functionalized GQDs and their nanocomposites as pivotal components in the development of advanced gas sensors.

Hydrothermally synthesized titanium/hydroxyapatite as photoactive and antibacterial biomaterial.

The present work investigated hydrothermal synthesis of titanium/hydroxyapatite (Ti/HA) nanocomposite at varied Ti content. The synthesis was performed by coprecipitation method using CaO, ammonium dihydrogen phosphate and titanium oxide chloride precursor with the additional cetyl trimethyl ammonium chloride as templating agent, followed by hydrothermal treatment at 150 °C. The derived materials were characterized by x-ray diffraction, x-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy analyses. The photocatalytic properties of materials were tested on methyl violet (MV) photocatalytic oxidation, meanwhile the antibacterial testing was performed against Escherichia coli, Staphylococcus aureus, Klebsiella pneumonia, and Streptococcus pyogenes. In addition, cytotoxicity evaluation of the materials as potential biomaterial was also conducted. The results showed that physicochemical character of Ti/HA exhibits exhibit the excellent properties to be photocatalyst along with antibacterial activity. From the detail study of effect of varied titanium content ranging from 5 to 10 %wt., the increasing crystallite size of anatase phase of about 25.81 nm and 38.22 nm for Ti content of 5 and 10 % wt., respectively. In other side, the band gap energy value increases as the increasing Ti content, i.e. the values are 3.08; 3.18; and 3.20 eV for Ti content of 5, 10, 20 % wt., respectively. The band gap energy is correlated with the photocatalytic activity which the highest MV degradation was 96.46% over Ti/HA with 20% wt. of Ti (Ti20/HA). The nanocomposites also express the antibacterial activity with comparable minimum inhibitory concentration (MIC) with other similar Ti/HA nanocomposites. The MIC values of Ti20/HA against E. coli, S. aureus, K. pneumonia, and S. pyogenes are 25; 25; 50 and 50 µg/mL, respectively. In addition, the cytotoxicity test revealed the potency to be a biomimetic material as shown by severe toxicity.

Enhancement of Catalytic Activity on Crude Palm Oil Hydrocracking over SiO2/Zr Assisted with Potassium Hydrogen Phthalate.

In this study, the catalytic activity of bifunctional SiO2/Zr catalysts prepared by template and chelate methods using potassium hydrogen phthalate (KHF) for crude palm oil (CPO) hydrocracking to biofuels was investigated. The parent catalyst was successfully prepared by the sol-gel method, followed by the impregnation of zirconium using ZrOCl2·8H2O as a precursor. The morphological, structural, and textural properties of the catalysts were examined using several techniques, including electron microscopy energy-dispersive X-ray with mapping, transmission electron microscopy, X-ray diffraction, particle size analyzer (PSA), N2 adsorption-desorption, Fourier transform infrared-pyridine, and total and surface acidity analysis using the gravimetric method. The results showed that the physicochemical properties of SiO2/Zr were affected by different preparation methods. The template method assisted by KHF (SiO2/Zr-KHF2 and SiO2-KHF catalysts) provides a porous structure and high catalyst acidity. The catalyst prepared by the chelate method assisted by KHF (SiO2/Zr-KHF1) exhibited excellent Zr dispersion toward the SiO2 surface. The modification remarkably enhanced the catalytic activity of the parent catalyst in the order SiO2/Zr-KHF2 > SiO2/Zr-KHF1 > SiO2/Zr > SiO2-KHF > SiO2, with sufficient CPO conversion. The modified catalysts also suppressed coke formation and resulted in a high liquid yield. The catalyst features of SiO2/Zr-KHF1 promoted high-selectivity biofuel toward biogasoline, whereas SiO2/Zr-KHF2 led to an increase in the selectivity toward biojet. Reusability studies showed that the prepared catalysts were adequately stable over three consecutive runs for CPO conversion. Overall, SiO2/Zr prepared by the template method assisted by KHF was chosen as the most prominent catalyst for CPO hydrocracking.

Effect of Red Mud and Rice Husk Ash-Based Geopolymer Composites on the Adsorption of Methylene Blue Dye in Aqueous Solution for Wastewater Treatment.

In this study, geopolymer originating from locally industrial byproducts as red mud (RM) was successfully prepared in the presence of different loadings of rice husk ash (RHA) used for the adsorption of methylene blue (MB) in wastewater. During geopolymerization, various mixing amounts between RM and RHA were conducted when the weight ratio of binder solution/activated alkali-metal solution (Na2SiO3/ NaOH 7 M) was 2.5 and the curing temperature was set at 60 °C for 24 h. As a result, the surface area value of the prepared geopolymer composited with RHA at 0 and 60% was increased from 19.2 to 29.5 m2/g, while the BJH pore size of the prepared geopolymer was reduced to 6.68 and 5.76 nm, respectively. In the dye removal test, higher additions of RHA in the RM-geopolymer maintained better retention of the MB ion due to the increase in the adsorption binding site. The maximum uptake amount of dyes performed at pH 8 was changed from 6.59 to 10.74 mg/g, while RHA was from 0 to 60% after 180 min of immersion in MB solution. The adsorption isotherms well obeyed the Langmuir model, as the relative coefficient R2 was 0.999. Based on these, the initial agricultural waste as RHA and industrial byproducts as RM were valued as functional materials used for dye treatment in wastewater.

Loading of Silver (I) Ion in L-Cysteine-Functionalized Silica Gel Material for Aquatic Purification.

The L-cysteine-functionalized silica (SG-Cys-Na+) matrix was effectively loaded with silver (I) ions using the batch sorption technique. Optimal Ag(I) loading into SG-Cys-Na+ reached 98% at pHi = 6, 80 rpm, 1 mg L-1, and a temperature of 55 °C. The Langmuir isotherm was found to be suitable for Ag(I) binding onto SG-Cys-Na+ active sites, forming a homogeneous monolayer (R2 = 0.999), as confirmed by FTIR spectroscopy. XRD analysis indicated matrix stability and the absence of Ag2O and Ag(0) phases, observed from diffraction peaks. The pseudo-second-order model (R2 > 0.999) suggested chemisorption-controlled adsorption, involving chemical bonding between silver ions and SG-Cys-Na+ surface. Thermodynamic parameters were calculated, indicating higher initial concentrations leading to increased equilibrium constants, negative ΔG values, positive ΔS values, and negative ΔH. This study aimed to explore silver ion saturation on silica surfaces and the underlying association mechanisms. The capability to capture and load silver (I) ions onto functionalized silica gel materials holds promise for environmental and water purification applications.

Controlled Growth of Semiconducting ZnO Nanorods for Piezoelectric Energy Harvesting-Based Nanogenerators.

Zinc oxide (ZnO) nanorods have attracted considerable attention in recent years owing to their piezoelectric properties and potential applications in energy harvesting, sensing, and nanogenerators. Piezoelectric energy harvesting-based nanogenerators have emerged as promising new devices capable of converting mechanical energy into electric energy via nanoscale characterizations such as piezoresponse force microscopy (PFM). This technique was used to study the piezoresponse generated when an electric field was applied to the nanorods using a PFM probe. However, this work focuses on intensive studies that have been reported on the synthesis of ZnO nanostructures with controlled morphologies and their subsequent influence on piezoelectric nanogenerators. It is important to note that the diatomic nature of zinc oxide as a potential solid semiconductor and its electromechanical influence are the two main phenomena that drive the mechanism of any piezoelectric device. The results of our findings confirm that the performance of piezoelectric devices can be significantly improved by controlling the morphology and initial growth conditions of ZnO nanorods, particularly in terms of the magnitude of the piezoelectric coefficient factor (d33). Moreover, from this review, a proposed facile synthesis of ZnO nanorods, suitably produced to improve coupling and switchable polarization in piezoelectric devices, has been reported.