RESUMEN
Prestressed high-strength concrete (PHC) pipe pile with the static press-in method has been widely used in recent years. The generation and dissipation of excess pore water pressure at the pile-soil interface during pile jacking have an important influence on the pile's mechanical characteristics and bearing capacity. In addition, this can cause uncontrolled concrete damage. Monitoring the change in excess pore water pressure at the pile-soil interface during pile jacking is a plan that many researchers hope to implement. In this paper, field tests of two full-footjacked piles were carried out in a viscous soil foundation, the laws of generation and dissipation of excess pore water pressure at the pile-soil interface during pile jacking were monitored in real time, and the laws of variation in excess pore water pressure at the pile-soil interface with the burial depth and time were analyzed. As can be seen from the test results, the excess pore water pressure at the pile-soil interface increased to the peak and then began to decline, but the excess pore water pressure after the decline was still relatively large. Test pile S1 decreased from 201.4 to 86.3 kPa, while test pile S2 decreased from 374.1 to 114.3 kPa after pile jacking. The excess pore water pressure at the pile-soil interface rose first at the initial stage of consolidation and dissipated only after the hydraulic gradient between the pile-soil interface and the soil surrounding the pile disappeared. The dissipation degree of excess pore water pressure reached about 75-85%. The excess pore water pressure at the pile-soil interface increased with the increase in buried depth and finally tended to stabilize.
RESUMEN
In order to examine the applicability of Fiber Bragg Grating (FBG) sensing technology in the static penetration of pipe piles, static penetration tests in clay were conducted using double-wall open and closed model pipe piles. The strain was measured using FBG sensors, and the plug height was measured using a cable displacement sensor. Using one open pile and two closed piles, the difference in pipe pile penetration was compared and analyzed. Based on FBG sensing technology and the strain data, the penetration characteristics of the pipe pile, such as axial force, lateral friction, and driving resistance were examined. Results showed that FBG sensing technology has superior testing performance for the pipe pile penetration process, can accurately reflect the strain time history of pipe piles, and can clearly reflect the penetration process of pipe piles with increasing penetration depth. In addition, the variation law of the characteristics of the jacked pile pile-soil interface was obtained. This test has significance for model tests and the engineering design of pipe piles.
RESUMEN
Photoelectric integrated testing technology was used to study precast piles during pile jacking at the pile-soil interface considering the influence of the earth and pore water pressures on its vertical bearing performance. The low temperature sensitive fiber Bragg grating (FBG) strain sensors and miniature silicon piezoresistive sensors were implanted in the model pile to test the changes of earth pressure, pore water pressure and pile axial force of the jacked pile at the pile-soil interface, and the influence of lateral pressure on pile axial force was studied. The test results showed that the nylon rod is feasible as a model pile. The FBG strain sensor had a stable performance and monitored changes in the axial force of the model pile in real time. The miniature earth and pore water pressure sensors were small enough to avoid size effects and accurately measured changes in the earth and pore water pressures during the pile jacking process. During pile jacking, the lateral earth pressure increased gradually in depth, and the lateral earth pressure at the same depth tended to decrease at greater depths. Lateral pressures caused the axial force of the pile to increases by a factor of 1-2, where the maximum was 2.7. Therefore, the influence of the lateral pressure must be considered when studying the residual pile stress.
RESUMEN
It is of great significance to study the mechanical behavior and permeability properties of hydrate-bearing sediments for a safe, efficient, and sustainable exploitation of hydrate. However, most of the studies conducted so far have focused only on a single stress field or seepage field, which is detached from practical engineering. In this paper, a new integrated experimental system (IES) was proposed, which realizes the coupling study of stress and seepage. The main body of IES is a triaxial subsystem and a seepage subsystem. The triaxial subsystem can realize in situ synthesis and triaxial shear of hydrate-bearing sediments (HBS). Stable seepage can be effectively formed using a constant pressure infusion pump and a back pressure valve. A series of shear-seepage coupling tests were carried out to verify the effectiveness of the IES and explore the stress-seepage coupling characteristics of HBS. The results show that stress has a significant influence on permeability, and its essence is the stress compression on the seepage channel. The stress-strain relationship, volume response, and permeability are related to each other. The permeability will be affected by the coupling of hydrate saturation (pore plugging), effective confining pressure (pore compression), and shear (fracture generation).
RESUMEN
To study the vertical compressive bearing characteristics of large-diameter rock-socketed cast-in-place piles, eight manually-excavated rock-socketed cast-in-place piles were subjected to vertical compressive on-site load and pile stress tests. The test results showed that the load-displacement (Q-s) curves of the eight test piles were all slow-varying, and the settlement of the piles was less than 11 mm, which met the minimum engineering requirements. The unloading rebound rate was between 55 and 75%, and the elastic working properties of the piles were apparent. The pile axial force gradually decreased with depth, and the slope of the axial force distribution curve reached a minimum in the moderately weathered muddy siltstone layer while the pile side friction resistance reached its maximum value. Pile end friction increases with the increase of load. But the pile end resistance was inversely proportional to the single pile length-to-diameter (L/D) ratio and the depth of rock embedment for the pile. The percentage of pile side friction resistance under maximum load was 86%, indicating that these were characteristic friction piles. Based on the test results and the current Chinese code, the friction coefficient of the pile side soil layer η and the total resistance coefficient of the rock-socketed section ζ were introduced. A revision to the calculation equation for the vertical bearing capacity of the rock-socketed cast-in-place pile in the code was proposed, together with an optimization design method for large-diameter rock-socketed cast-in-place piles.