RESUMEN
The main goal of this study is the comparison of different reinforcement architectures on the low-velocity impact behavior of green composites. The study includes the comparison of unidirectional, basket weave, and twill weave flax/PLA composites, they are subjected to unidirectional tensile tests, drop-weight impact tests, and after-impact compression tests. Results show that the unidirectional composite demonstrates superior tensile strength and initial modulus due to reduced fiber crimp, while basket weave exhibits the highest energy absorption capability and strain capacity attributed to its higher fiber-weight ratio and fiber crimp. Unidirectional composite also shows a larger impacted damage area compared to basket weave and twill weave, attributed to its internal architecture. Residual compressive strength across all composites decreased by 40% compared to the reference sample. However, the reduction in stiffness after impact was different, UD/PLA composite stiffness was reduced by 30% while the reduction in BW/PLA and T/PLA composites was about 20%.
RESUMEN
The main advantage of green composites is their biodegradability, but this biodegradability can also be considered a drawback if the degradation appears during the service life of the component. Therefore, the study of the mechanical behavior of green composites after hygrothermal aging tests is necessary to analyze their degradation process. This study aims to comprehensively analyze the hygrothermal aging behavior and aging mechanism of flax-fiber-reinforced polylactic acid (PLA) biocomposites. The fully biodegradable composites are manufactured by compression molding. In addition, the influence of atmospheric-pressure plasma treatment on the mechanical properties of the biocomposite is studied. Specimens are exposed to water vapor and 40 °C environmental conditions in a stove for up to 42 days. Several specimens of each type are taken out at regular intervals and tested to examine the water absorption, mechanical properties, and thermal characterization. The results show that the stiffness was significantly reduced after 24 h due to matrix degradation, while the strength was reduced only after three weeks.
RESUMEN
Significant progress has been made in green composites developing fully biodegradable composites made of microbially degradable polymers reinforced with natural fibers. However, an improvement in the development of numerical models to predict the damage of green composites is necessary to extend their use in industrial applications of structural responsibility. This paper is focused on developing a numerical model that can predict the failure modes of four types of bumper beams made of flax/PLA green composites with different cross sections. The predictions regarding energy absorption, contact force history, and extension of delamination were compared with experimental results to validate the FEM model, and both results revealed a good agreement. Finally, the FEM model was used to analyze the failure modes of the bumper beams as a function of the impact energy and cross-section roundness. The impact energy threshold defined as the maximum absorbed-energy capability of the beam match with the impact energy that produces delaminations extended through all the cross sections. Experimental and numerical results revealed that the threshold energy, where the maximum energy-absorption capability is reached, for Type A is over 60 J; for Type B and C is around 60 J; and for Type D is at 50 J. Since delamination is concentrated at the cross-section corners, the threshold energy decreases with the cross-section roundness because the higher the roundness ratio, the wider the delamination extension.
RESUMEN
The present work aims to analyze the buckling behavior of nonlinear elastic columns with different open cross-sections and slenderness ratios to verify the limits of the modified Ludwick law to predict the critical buckling load. The results of the analytical formulation based on the modified Ludwick law are compared with a FEM numerical model using the Marlow hyperelastic behavior and experimental results conducted on flax/PLA specimens with three different open cross-sections. The comparative results show that the numerical predictions agree with the experimental results in all the cases. The FEM model can exactly reproduce the buckling behavior of the C-section columns. However, the prediction errors for the C90 and C180 columns are higher than for the C60 columns. Moreover, the theoretical estimations indicate that the C90 cross-section column is the limit of application of the modified Ludwick law to predict the critical buckling load of nonlinear elastic columns with open cross-sections, and the C180 column is out of the prediction limits. Generally, the numerical and theoretical models underestimated the scattering effects of the predictions because more experimental variables were not considered by the models.
RESUMEN
The aim of the present work is to provide a methodology to evaluate the influence of stacking sequence on the ballistic performance of ultra-high molecular weight polyethylene (UHMWPE) protections. The proposed methodology is based on the combination of experimental tests, numerical modelling, and Artificial Neural Networks (ANN). High-velocity impact experimental tests were conducted to validate the numerical model. The validated Finite Element Method (FEM) model was used to provide data to train and to validate the ANN. Finally, the ANN was used to find the best stacking sequence combining layers of three UHMWPE materials with different qualities. The results showed that the three UHMWPE materials can be properly combined to provide a solution with a better ballistic performance than using only the material with highest quality. These results imply that costs can be reduced increasing the ballistic limit of the UHMWPE protections. When the weight ratios of the three materials remain constant, the optimal results occur when the highest-performance material is placed in the back face. Furthermore, ANN simulation showed that the optimal results occur when the weight ratio of the highest-performance material is 79.2%.
RESUMEN
Common practice of surgical treatments in orthopaedics and traumatology involves cutting processes of bone. These operations introduce risk of thermo-mechanical damage, since the threshold of critical temperature producing thermal osteonecrosis is very low. Therefore, it is important to develop predictive tools capable of simulating accurately the increase of temperature during bone cutting, being the modelling of these processes still a challenge. In addition, the prediction of cutting forces and mechanical damage is also important during machining operations. As the accuracy of simulations depends greatly on the proper choice of the thermo-mechanical properties, an essential part of the numerical model is the constitutive behaviour of the bone tissue, which is considered in different ways in the literature. This paper focuses on the review of the main contributions in modelling of bone cutting with special attention to the bone mechanical behaviour. The aim is to give the reader a complete vision of the approaches commonly presented in the literature in order to help in the development of accurate models for bone cutting.
Asunto(s)
Huesos/cirugía , Modelos Biológicos , Procedimientos Ortopédicos/métodos , Animales , Huesos/lesiones , Análisis de Elementos Finitos , Fracturas Óseas , Humanos , Fenómenos MecánicosRESUMEN
Carbon Fiber Reinforced Polymer (CFRPs) composites are extensively used in structural applications due to their attractive properties. Although the components are usually made near net shape, machining processes are needed to achieve dimensional tolerance and assembly requirements. Drilling is a common operation required for further mechanical joining of the components. CFRPs are vulnerable to processing induced damage; mainly delamination, fiber pull-out, and thermal degradation, drilling induced defects being one of the main causes of component rejection during manufacturing processes. Despite the importance of analyzing thermal phenomena involved in the machining of composites, only few authors have focused their attention on this problem, most of them using an experimental approach. The temperature at the workpiece could affect surface quality of the component and its measurement during processing is difficult. The estimation of the amount of heat generated during drilling is important; however, numerical modeling of drilling processes involves a high computational cost. This paper presents a combined approach to thermal analysis of composite drilling, using both an analytical estimation of heat generated during drilling and numerical modeling for heat propagation. Promising results for indirect detection of risk of thermal damage, through the measurement of thrust force and cutting torque, are obtained.