Dataset for deformation behavior of pure titanium grade 2 materials during continuous extrusion.

There is a huge application and demand for titanium alloys with excellent upgraded mechanical, metallurgical, and material properties in modern industries. To fulfill the demand of modern industries metal forming process is highly desirable. Among all metal forming processes, a special type of cold forming called the continuous extrusion process has been highly appropriate to fulfill the demands. The theoretical analysis has been carried out through Upper Bound Method. The numerical simulation has been carried out through the three-dimensional finite element tool DEFORM-3D. The experimental plan and design have been carried out using Taguchi (2^3) array methods on the MINITAB platform by considering extrusion wheel velocity and feedstock temperature as chief extrusion parameters. The experimental validation process was executed on 12.5 mm CP- Titanium grade 2 feedstock materials using a TBJ350 CONFORM machine setup. The optimization process of parameters for the optimum value of the response variable was carried out through Grey Relational Analysis.

Improvement in Thermal Storage Effectiveness of Paraffin with Addition of Aluminum Oxide Nanoparticles.

The output of the latent heat storage devices (LHSDs), based on some phase change materials (PCMs), depends upon the thermophysical properties of the phase change material used. In this study, a paraffin-based nanofluid, blended with aluminum oxide (Al2O3) nanoparticles, is used as PCM for performance evaluation. A three-dimensional (3D) numerical model of regenerative type shell-and-tube LHSD is prepared using COMSOL Multiphysics® 4.3a software to estimate the percentage of melt and the average temperature of the analyzed nanofluids. The results of this study are in close agreement with those reported in the literature, thereby ensuring the validation of the numerically predicted results. The effects of adding the nanoparticles on the rate of melting, as well as solidification and rate of stored/liberated energy, are studied. The results revealed that, by adding 10% nanoparticles of Al2O3, the melting rate of pure-paraffin-based LHSD improved by about 2.25 times. In addition, the rate of solidification was enhanced by 1.8 times. On the other hand, the heat of fusion and specific heat capacities were reduced, which, in turn, reduced the latent and sensible heat-storing capabilities. From the outcomes of the present research, it can be inferred that combining LHSD with a solar water heater may be used in technologies such as biogas generation.

Effect of Sintering Temperatures, Reinforcement Size on Mechanical Properties and Fortification Mechanisms on the Particle Size Distribution of B4C, SiC and ZrO2 in Titanium Metal Matrix Composites.

Titanium metal matrix composites/TMMCs are reinforced ceramic reinforcements that have been developed and used in the automotive, biological, implants, and aerospace fields. At high temperatures, TMMCs can provide up to 50% weight reduction compared to monolithic super alloys while maintaining comparable quality or state of strength. The objective of this research was the analysis and evaluation of the effect/influence of different sintering temperatures, reinforcement size dependence of mechanical properties, and fortification mechanisms on the particle size distribution of B4C, SiC, and ZrO2 reinforced TMMCs that were produced and fabricated by powder metallurgy/PM. SEM, XRD, a Rockwell hardness tester, and the Archimedes principle were used in this analysis. The composites' hardness, approximation, tensile, yielding, and ultimate strength were all increased. As the composite was reinforced with low-density ceramics material and particles, its density decreased. The volume and void content in all the synthesized specimens is below 1%; this is the result of good sample densification, mechanical properties and uniform distribution of the reinforced particle samples; 5% B4C, 12.5% SiC, 7.5% ZrO2, 75% Ti develop higher mechanical properties, such as higher hardness, approximation tensile, yielding, and ultimate strength and low porosity.

Investigation of Mechanical and Tribological Behaviors of Aluminum Based Hybrid Metal Matrix Composite and Multi-Objective Optimization.

Aluminum metal matrix composites are potential materials for aerospace and automobile industrial applications due to their enhanced mechanical and tribological properties. Aluminum reinforced with silicon carbide particles has been developed with enhanced mechanical and tribological behavior, but it lacks wettability between matrix and reinforcement causing weak bonding, which reduces the degree of enhancement. The objectives of this study were to fabricate aluminum-based metal matrix composites with enhanced wettability at varying stirring speeds (350, 450, 550 rpm), stirring time (5, 10, 15 min), weight percentage of SiC (0, 5, 10 wt.%), and weight percentage of MoS2 (0, 2, 4 wt.%). Nine samples were fabricated using stir casting based on Taguchi L9 orthogonal array. Hardness, tensile strength, and wear rate of the developed composite were investigated and analyzed as a single response characteristic using Taguchi's signal-to-noise ratio and as a multi-response characteristic using hybrid Taguchi-grey relational analysis (HTGRA). The results revealed that the addition of SiC in the composite produced better hardness, tensile strength, and wear rate. The addition of MoS2 in the composite showed better hardness and tensile strength only up to 2 wt.% of MoS2, and in the case of wear rate, the addition of MoS2 in the composite up to 4% showed better wear resistance. Al-SiC-MoS2 hybrid composite shows better enhancement in hardness, tensile strength, and wear resistance than the Al-SiC composite.

True duplicate bladder exstrophy: a rare lesion.

A two-day-old newborn male child with a rare variant of exstrophy bladder was managed in our institute. The child has true duplicate bladder exstrophy which is extremely rare and only 8 cases reported in the world literature so far. We describe another one and briefly review the literature.

Ectopia cordis associated with Cantrell's pentalogy.

Cantrell's pentalogy with ectopia cordis is an extremely rare and lethal congenital anomaly, with a reported incidence of 1:100,000 births in developed countries. We report a neonate who presented with ectopia cordis along with cleft lower sternum, upper abdominal wall defect, ectopic umbilicus, diaphragmatic defect, and interventricular septal defect. The neonate had respiratory distress with peripheral cyanosis and died because of acidosis and electrolyte imbalance before surgical intervention could be undertaken. We discuss the case and present a brief review of literature and of embryogenesis.