3D electro-Fenton augmented with iron-biochar particle electrodes derived from waste iron bottle caps and sugarcane bagasse for the remediation of sodium dodecyl sulphate.

The present work demonstrates a novel strategy of synthesizing iron-biochar (Fe@BCSB) composite made with the waste iron bottle cap and sugar cane bagasse for implementation in the three-dimensional electro-Fenton (3DEF) process. The catalytic ability of the Fe@BCSB composite was explored to remediate the sodium dodecyl sulphate (SDS) surfactant from wastewater at neutral pH. At the optimum operating condition of Fe@BCSB dose of 1.0 g L-1, current density of 4.66 mA cm-2, and Na2SO4 dose of 50 mM, nearly 92.7 ± 3.1% of 20 mg L-1 of SDS abatement was attained during 120 min of electrolysis time. Moreover, the Fe@BCSB showed significant recyclability up to six cycles. Besides, other organics were successfully treated with more than 85% abatement efficiency in the proposed Fe@BCSB-supported 3DEF process. The total operating cost obtained during SDS treatment was around 0.31 US$ m-3 of wastewater. The phytotoxicity test revealed the positive impact of the 3DEF-treated effluent on the germination of the Vigna radiata. The electron paramagnetic resonance conveyed •OH as the prevailing reactive species for the oxidation of SDS in the 3DEF process. Further, about 81.3 ± 3.8% of SDS and 53.7 ± 4.1% of mineralization efficacy were acquired from the real institutional sewage.

Battery waste-derived magnetic Fe-Mn-Zn/C composites as an electro-Fenton-like catalyst for the degradation of sodium dodecyl sulfate surfactant.

A batch-scale electro-Fenton (EF) process was performed using graphite anode and waste battery-based Fe -Mn -Zn/C electrocatalyst coated on low-cost graphite felt cathode. The effectiveness of the EF's performance was evident with around 83.9 + 4.1% removal of 20 mg/L of sodium-dodecyl sulfate surfactant (SDS) at an optimum current density (CD) of 5.0 mA/cm2, Na2SO4 of 0.05 M, initial pH of 7.2, and electrolysis time of 180 min. Moreover, nearly 1.78-fold more removal of SDS was achieved in EF than in the electro-oxidation process operated without any catalyst. The operating cost of 0.35 $ of per m3 per order was needed to treat SDS wastewater. The remediation of SDS follows pseudo-first-order kinetics with a rate constant of 0.0095 min-1. Additionally, 90.3 + 2.1% of SDS and 57 + 2.6% of total organic carbon (TOC) removal was attained during 240 min of treatment time in secondary treated real wastewater; hence, additional 60 min of treatment time is required for effectively treating real wastewater than synthetic wastewater. Thus, EF is effective with battery waste-derived magnetic catalyst for treating wastewater containing SDS, which can lead to achieving sustainable environmental goals.

Nutrient removal from domestic wastewater: A comprehensive review on conventional and advanced technologies.

Nitrogen and phosphorous are indispensable for growth and vitality of living beings, hence termed as nutrients. However, discharge of nutrient rich waste streams to aquatic ecosystems results in eutrophication. Therefore, nutrient removal from wastewater is crucial to meet the strict nutrient discharge standards. Similarly, nutrient recovery from waste streams is vital for the realization of a circular economy by avoiding the depletion of finite resources. This manuscript presents analysis of existing information on different conventional as well as advanced treatment technologies that are commonly practiced for the removal of nutrient from domestic wastewater. First, the information pertaining to the biological nutrient removal technologies are discussed. Second, onsite passive nutrient removal technologies are reviewed comprehensively. Third, advanced nutrient removal technologies are summarized briefly. The mechanisms, advantages, and disadvantages of these technologies along with their efficiencies and limitations are discussed. An integrated approach for simultaneous nutrient removal and recovery is recommended. The fifth section of the review highlights bottlenecks and potential solutions for successful implementation of the nutrient removal technologies. It is anticipated that the review will offer an instructive overview of the progress in nutrient removal and recovery technologies and will illustrate necessity of further investigations for development of efficient nutrient removal and recovery processes.

The potential utilization of slag generated from iron- and steelmaking industries: a review.

Along with iron and steel production, large amount of slag is generated. Proper management on the iron- and steelmaking slag is highly demanded due to the high cost of direct disposal of the slag to landfill, which is the most adopted management approach. In this article, the potential application of iron- and steelmaking slag has been reviewed, which included the slag utilization in construction as cement and sand, in water, soil, and gas treatment, as well as in value material recovery. In addition, the challenge and required effort to be made in iron- and steelmaking slag management have been discussed.

Acute Impact of Chlortetracycline on Nitrifying and Denitrifying Processes.

In the current study, sequential nitrification and anoxic experiments in synthetic municipal wastewater were exposed to 0.5 to 100 mg/L of chlortetracycline for 24 h to evaluate acute impact on the nitrification, and denitrification processes of biological treatment. Both processes were significantly (p < 0.05) inhibited at >50 mg/L of chlortetracycline, and the results revealed that nitrification was adversely affected by chlortetracycline compared with the anoxic process. In nitrification, chemical oxygen removal (COD) and ammonia oxidation kinetics were 50% inhibited at 10 mg chlortetracycline/L, and nitrite oxidation kinetics at 0.5 mg chlortetracycline/L. Likewise, in the anoxic process, 14 and 10 mg/L of chlortetracycline inhibited 50% of COD removal and nitrate reduction kinetics, respectively. In nitrification and denitrification, 90% of chlortetracycline was removed by adsorbing onto sludge suspended solids. In addition, a higher chlortetracycline concentration in anoxic effluent, compared with aerobic effluents, indicated a dissimilarity in the composition of sludge solids, pH, and biomass production for both processes.

Sediment in-situ bioremediation by immobilized microbial activated beads: Pilot-scale study.

A field study was carried out to investigate the sediment in-situ bioremediation by adding microbial activated beads. In this work, Calcium carbonate, silicon dioxide, activated carbon powder, attapulgite powder, sodium alginate, microbial liquid and polyvinyl alcohol were utilized to make the immobilized microbial activated beads. Field experiment results showed that the removal rate of NH4+-N, TN and COD in overlying water reached about 61.8%, 87.5% and 87.1%, respectively. The initial concentration of NH4+-N, TN and COD was 159 mg/L, 6.24 mg/L and 7.28 mg/L, whereas and the final concentration was 58 mg/L, 0.78 mg/L and 0.94 mg/L when water temperature, DO, pH and C/N ratio were 25-30 °C, 2-3 mg/L, 7.0-8.0 and 10-15, respectively. Moreover, under optimal temperature condition (25-30 °C), the removal rate of TOC, TN, heterotrophic bacteria and sulfur bacteria in the river sediment reached to 46.5%, 50.7%, 39.2% and 73.2%, respectively.

Lipid Production for Biodiesel from Sludge and Crude Glycerol.

Oleaginous yeast Trichosporon oleaginosus was studied for lipid production using municipal sludge with or without fortification of crude glycerol in a 15-L fermenter. The maximum lipid content (concentration) was 32.0% w/w (9.35 g/L), 33.6% (10.13 g/L), 33.3% (9.13 g/L), and 33.1% (9.03 g/L) w/w with the addition of 25, 50, 100, and 150 g/L glycerol, respectively. Glycerol concentration had little effect on lipid accumulation. However, glycerol concentration substantially affected increase of biomass concentration and cell count. The suitable glycerol concentration was approximately 40 g/L for Trichosporon oleaginosus growing in sludge medium with initial suspended solids (SS) concentration 30 g/L. Addition of nitrogen to sludge-glycerol medium enhanced lipid and biomass concentration. The energy conversion efficiency was 1.78, 1.55, and 1.71 with no nitrogen added, with addition of 1 g/L urea, and 3.7 g/L peptone, respectively. The biodiesel production cost was estimated nearly 0.75 US$/L.

Developing an Integrated Modeling Tool for River Water Quality Index Assessment.

The goal of this study was to establish a modeling tool for river water quality with a direct linkage to the water quality index (WQI5) calculation and the river water quality model, the Water Quality Analysis Simulation Program (WASP), for pollutant transport modeling. The integrated WASP and WQI5 tool was field-tested to assess pollutant loadings and their impacts on river environment. Suspended solid (SS) and electric conductivity (EC) correlation equations and the WQI5 calculation tool were included in the water quality model and direct WQI5 calculation. The SS concentration, which was influenced by river flows, had crucial effects on river water quality and WQI5 values. EC value was controlled by dissolution of soil minerals, which was affected by the watershed drainage area and surface runoff. The integrated system could establish a direct correlation for river water quality, river flow, and WQI5.

Energy balance of biofuel production from biological conversion of crude glycerol.

Crude glycerol, a by-product of biodiesel production, has gained significant attention as a carbon source for biofuel production. This study evaluated the energy balance of biodiesel, hydrogen, biogas, and ethanol production from 3.48 million L of crude glycerol (80% w/v). The conversion efficiency (energy output divided by energy invested) was 1.16, 0.22, 0.27, and 0.40 for the production of biodiesel, hydrogen, biogas, and ethanol respectively. It was found that the use of crude glycerol for biodiesel production was an energy gain process, with a positive energy balance and conversion efficiency of greater than 1. The energy balance revealed a net energy gain of 5226 GJ per 1 million kg biodiesel produced. Production of hydrogen, biogas and ethanol from crude glycerol were energy loss processes. Therefore, the conversion of crude glycerol to lipids and subsequently to biodiesel is suggested to be a better option compared to hydrogen, biogas, or ethanol production with respect to energy balance.

Biopolymers Production by Mixed Culture and Their Applications in Water and Wastewater Treatment.

Thirteen extracellular polymeric substances (EPS) producing bacterial strains were cultivated (as pure/mixed culture) in sterilized sludge (suspended solids: 25 g/L). The mixed culture produced higher concentrations of EPS (4.9 g/L) as compared to that of the pure culture (2.7-3.7 g/L). The harvested EPS were examined for their flocculation performance (turbidity removal and dewatering) in jar tests using kaolin suspensions with Ca2+. Broth (B-EPS) revealed high kaolin flocculating activity (91.2%) at very low concentrations (0.8 mg B-EPS/g kaolin) and it was comparable to the chemical polymer, Magnafloc-155 (90.4% at 0.2 mg/g kaolin). B-EPS also exhibited very good flocculation performance (turbidity removal %) in river water (93.5%), municipal wastewater (91.7%) and brewery wastewater (81.8%). The study revealed that the mixed culture consortium could be used for the production of highly efficient flocculants.

Anaerobic digestion of thermal pre-treated sludge at different solids concentrations--Computation of mass-energy balance and greenhouse gas emissions.

The effect of thermal pre-treatment on sludge anaerobic digestion (AD) efficiency was studied at different total solids (TS) concentrations (20.0, 30.0 and 40.0 g TS/L) and digestion times (0, 5, 10, 15, 20 and 30 days) for primary, secondary and mixed wastewater sludge. Moreover, sludge pre-treatment, AD and disposal processes were evaluated based on a mass-energy balance and corresponding greenhouse gas (GHG) emissions. Mass balance revealed that the least quantity of digestate was generated by thermal pre-treated secondary sludge at 30.0 g TS/L. The net energy (energy output-energy input) and energy ratio (energy output/energy input) for thermal pre-treated sludge was greater than control in all cases. The reduced GHG emissions of 73.8 × 10(-3) g CO2/g of total dry solids were observed for the thermal pre-treated secondary sludge at 30.0 g TS/L. Thermal pre-treatment of sludge is energetically beneficial and required less retention time compared to control.

Corrosion and stability study of Bacillus thuringiensis var. kurstaki starch industry wastewater-derived biopesticide formulation.

Biopesticides are usually sprayed on forests by using planes made up of aluminum alloy. Bioval derived from starch industry wastewater (SIW) in suspension form was developed as stable anticorrosive biopesticide formulation. In this context, various anticorrosion agents such as activated charcoal, glycerin, ethylene glycol, phytic acid, castor oil and potassium silicate were tested as anticorrosive agents. There was no corrosion found in Bioval formulation where potassium silicate (0.5% w/v) was added and compared with Foray 76 B, as an industrial standard, when stored over 6 months. In relation to other parameters, the anticorrosion formulation of Bioval+buffer+KSi reported excellent zeta potential (-33.19 ± 4 mV) and the viscosity (319.13 ± 32 mPa.s) proving it's stability over 6 months, compared to the standard biopesticide Foray 76 B (-36.62 ± 4 mV potential zeta, pH 4.14 ± 0.1 and 206 ± 21 mPa.s viscosity). Metal analysis of the different biopesticides showed that Bioval+buffer+KSi has no corrosion (5.11 ± 0.5 mg kg(-1) of Al and 13.53 ± 1.5 mg kg(-1) of Fe) on the aluminum alloy due to the contribution of sodium acetate buffer at pH 5. The bioassays reported excellent results for Bioval+Buffer+KSi (2.95 ± 0.3 × 10(9) CFU mL(-1) spores and 26.6 ± 2.7 × 10(9) IU L(-1) Tx) compared with initial Bioval (2.46 ± 0.3 × 10(9) CFU mL(-1) spores and 23.09 ± 3 × 10(9) IU L(-1) Tx) and Foray 76 B (2.3 ± 0.2 × 10(9) CFU mL(-1) spores and 19.950 ± 2.1 UI L(-1) Tx) which was due to the break-up of the external chitinous membrane due to abrasive action of potassium silicate after ingestion by insects. The contribution of sodium acetate buffer and potassium silicate (0.5% and at pH = 5) as anticorrosion agent in the Bioval allowed production of an efficient biopesticide with a reduced viscosity and favorable pH as compared to Foray 76 B which enhanced the entomotoxic potential against spruce budworm (SB) larvae (Lepidoptera: Choristoneura fumiferana).

Effects of bed depths and the ratio of aerobic to anaerobic zone on the performance of horizontal subsurface flow macrophyte-assisted high-rate vermifilters treating synthetic brewery wastewater.

Effects of total vermibed depth, as well as the ratio of aerobic (the unsubmerged) to anaerobic (the submerged) zone on the performance of the horizontal subsurface flow macrophyte-assisted vermifilters (HSSF-MAVFs) treating synthetic brewery wastewater at a higher hydraulic loading rate (HLR), were investigated for the first time. Results showed that the HSSF-MAVF with a 50 cm total and 18 cm submerged vermibed depth yielded the optimum removal of the pollutants, ensuring a (91.2 ± 1.7)%, (81.8 ± 1.9)%, (67.4 ± 3.9)%, and (63.1 ± 2.3)% removal of chemical oxygen demand (COD), ammonium N (NH4 + -N), total N (TN), and organic N, respectively, whereas there was an increase of (142 ± 6.3)% in the effluent nitrate-N (NO3 - -N) than that in the influent. At the optimum condition, the effluent concentrations of all the pollutants including COD, NH4 + -N, NO3 - -N, TN, and organic N were well below the surface water discharge standards specified by the Central Pollution Control Board (CPCB), and thus, the effluent of the HSSF-MAVF could be safely discharged into the surface water bodies. PRACTITIONER POINTS: Total vermibed depth of HSSF-MAVFs was optimized for organic and nitrogen removal. HSSF-MAVFs were subjected to the higher HLR of synthetic brewery wastewater. Removal of COD and NH4 + -N was decreased with the increase in submerged bed depth. Removal of organic N and TN was increased with the increase in submerged bed depth. Total/unsubmerged bed depth had a positive impact on the organic and N removal.

Performance evaluation of hybrid electrochemical oxidation and ultraviolet light-based persulfate process for the abatement of sodium dodecyl sulfate from wastewater.

The application of hybrid advanced oxidation processes (AOPs) is an efficacious way to remediate emerging contaminants from wastewater. In the present research work, a hybrid electrochemical oxidation and ultraviolet light-based persulfate activation processes (EO-UV/PS) were used to efficiently degrade sodium dodecyl sulfate (SDS) surfactant from synthetic and municipal wastewater. By operating the EO-UV/PS at optimum operating conditions at pH of 7.0, NaCl of 0.02 M, current density of 6.4 mA/cm2, persulfate dose of 2.5 mM, and operating period of 180 min, about 94.5 ± 2.8% of SDS (20 mg/L) removal was achieved from synthetic wastewater. The abetment of SDS in both EO and UV/PS obeyed pseudo-first-order kinetics with a rate constant of 0.012 and 0.019 min-1, respectively. Moreover, the economic analysis revealed 0.23 $ m-3 order-1 as the operating cost for degrading SDS in EO-UV/PS. The degradation pathway experimentation suggested the generation of lauric acid by-product during SDS abatement. Besides, nearly 89.3 ± 2.9% of SDS and 58.7 ± 2.4% of total organic carbon reduction was also achieved from real municipal wastewater. Phytotoxicity test on Vigna radiata affirms the non-toxic nature of the EO-UV/PS effluent.

A critical review on the vermicomposting of organic wastes as a strategy in circular bioeconomy: mechanism, performance, and future perspectives.

To meet the current need for sustainable development, vermicomposting (VC), a natural, eco-friendly, and cost-effective technology, can be a wise selection for the bioconversion of organic wastes into value-added by-products. However, no one has tried to establish the VC technology as an economically sustainable technology by exploring its linkage to circular bioeconomy. Even, no researcher has made any effort to explore the usability of the earthworms (EWs) as a protein supplement while assessing the economic perspectives of VC technology. Very few studies are available on the greenhouse gas (GHG) emission potential of VC technology. Still, the contribution of VC technology towards the non-carbon waste management policy is not yet explored. In the current review, a genuine effort has been made to inspect the contribution of VC technology towards the circular bioeconomy, along with evaluating its capability to bioremediate the organic wastes generated from domestic, industrial, and agricultural premises. The potential of the EWs as a protein source has also been explored to strengthen the contribution of VC technology towards the circular bioeconomy. Moreover, the linkage of the VC technology to the non-carbon waste management policy has been comprehensively demonstrated by highlighting its carbon sequestration and GHG emission potentials during the treatment of organic wastes. It has been observed that the cost of food production was reduced by 60-70% by replacing chemical fertilizers with vermicompost. The implication of the vermicompost significantly lessened the harvesting period of the crops, thereby helping the farmers attain higher profits by cultivating more crops in a single calendar year on the same plot. Furthermore, the vermicompost could hold the soil moisture for a long time, lessening the water demand up to 30-40%, which, in turn, reduced the frequency of irrigation. Also, the replacement of the chemical fertilizers with vermicompost resulted in a 23% increment in the grapes' yield, engendering an extra profit of up to 110000 rupees/ha. In Nepal, vermicompost has been produced at a cost of 15.68 rupees/kg, whereas it has been sold to the local market at a rate of 25 rupees/kg as organic manure, ensuring a net profit of 9.32 rupees/kg of vermicompost. EWs embraced 63% crude protein, 5-21% carbohydrates, 6-11% fat, 1476 kJ/100 g of metabolizable energy, and a wide range of minerals and vitamins. EWs also contained 4.11, 2.04, 4.43, 2.83, 1.47, and 6.26 g/kg (on protein basis) of leucine, isoleucine, tryptophan, arginine, histidine, and phenylalanine, respectively, enhancing the acceptability of the EW meal (EWM) as the protein supplement. The inclusion of 3 and 5% EWM in the diet of broiler pullets resulted in a 12.6 and 22.5% increase in their feed conversion ratio (FCR), respectively after one month. Similarly, when a 100% fish meal was substituted by 50% EWM and 50% fish meal, the FCR and growth rate of Parachanna obscura were increased substantially. The VC of maize crop residues mixed with pig manure, cow dung, and biochar, in the presence of Eisenia fetida EWs, yielded only 0.003-0.081, 0-0.17, and 130.40-189.10 g CO2-eq.kg-1 emissions of CO2, CH4, and N2O, respectively. Similarly, the VC of tomato stems and cow dung ensured 2.28 and 5.76 g CO2-eq.kg-1 CO2 emissions of CH4 and N2O, respectively. Additionally, the application of vermicompost at a rate of 5 t/ha improved the soil organic carbon proportion and aggravated carbon sequestration. The land application of vermicompost improved micro-aggregation and cut down the tillage, reducing GHG emissions and triggering carbon sequestration. The significant findings of the current review suggest that VC technology potentially contributes to the concept of circular bioeconomy, substantially negotiates potential GHG emissions, and complies with the non-carbon waste management policy, reinforcing its acceptability as an economically sound and environmentally benevolent organic waste bioremediation alternative.

Using innovative copper-loaded activated alumina (Cu/AA) as the catalyst for catalytic wet peroxidation (CWPO) of catechol.

In this study, copper-loaded activated alumina (Cu/AA) was synthesized and used for the CWPO of catechol (a representative refractory organic pollutant). Various characterization techniques were deployed to characterize the catalysts, e.g., activated alumina (AA), as well as pristine and spent 1% Cu/AA. The innovative 1% Cu/AA catalyst exhibited good thermal stability up to 1173 K with a marginal weight loss of 13%. The Cu species were well dispersed on the activated alumina framework with no significant cluster formation. Typically, the average copper particle size of 5 nm was dispersed on the AA framework. Catechol removal was observed to be 92% with 87% mineralization at optimized conditions (initial catechol concentration = 200 mg/L, catalyst dose of 1% Cu/AA = 2 g/L; temperature = 323 K; pH = 6; and H2O2/catechol stoichiometric ratio = 0.5). The mineralization of catechol was analyzed using mass spectroscopy, with the associated mechanism has been elucidated. Results of this study indicated that synthesized catalyst has phenomenal advantages in terms of simple separation and high removal efficiency of catechol, suggesting the feasibility of employing Cu/AA as the effective catalyst for the CWPO of catechol.

Spatiotemporal-based automated inundation mapping of Ramsar wetlands using Google Earth Engine.

Wetlands are one of the most critical components of an ecosystem, supporting many ecological niches and a rich diversity of flora and fauna. The ecological significance of these sites makes it imperative to study the changes in their inundation extent and propose necessary measures for their conservation. This study analyzes all 64 Ramsar sites in China based on their inundation patterns using Landsat imagery from 1991 to 2020. Annual composites were generated using the short-wave infrared thresholding technique from June to September to create inundation maps. The analysis was carried out on each Ramsar site individually to account for its typical behavior due to regional geographical and climatic conditions. The results of the inundation analysis for each site were subjected to the Mann-Kendall test to determine their trends. The analysis showed that 8 sites exhibited a significantly decreasing trend, while 14 sites displayed a significantly increasing trend. The accuracy of the analysis ranged from a minimum of 72.0% for Hubei Wang Lake to a maximum of 98.0% for Zhangye Heihe Wetland National Nature Reserve. The average overall accuracy of the sites was found to be 90.0%. The findings emphasize the necessity for conservation strategies and policies for Ramsar sites.

Vermifiltration: Strategies and techniques to enhance the organic and nutrient removal performance from wastewater.

The vermifiltration (VF) technology has gained significant attention as a green alternative for remediating domestic and industrial wastewater over the last few decades. Of late, the implementation of various modifications to the orthodox VF technology, including tweaks in the design and operation of the vermifilters, has been portrayed in the available literature. However, owing to the scatteredness of the available information, the knowledge regarding the execution of the modified vermifilters is still inadequate. Hence, an effort has been made to comprehensively overview the innovative strategies and techniques adopted to improve the organic and nutrient removal potential of the VFs from wastewater. In addition, future perspectives have been recognized to design more efficient and sustainable VFs. This review explores more of such novel tactics to improve the performance of the VF technology regarding organic and nutrient removal from wastewater. PRACTITIONER POINTS: Innovative strategies and techniques implemented to VF technology were comprehensively overviewed. Design modification and advantages of each innovation were highlighted. The pollutant removal performance of every modification was emphasized. Modified vermifilters were better than the conventional vermifilters in terms of organic and nutrient removal from the wastewater.

Comparison of GHG emissions from open field burning and anaerobic digestion of rice straw.

Rice straw (RS) has been burned in open fields in many countries, which is a growing environmental concern. Anaerobic digestion (AD) of RS is one of the sustainable alternatives to open burning of RS for converting the biomass into methane, carbon dioxide, and digestate for use as agricultural manure. The present study evaluates the RS generation, use patterns, and greenhouse gas emissions from open field burning and the AD of RS. Results indicate the AD of RS offers greater environmental benefits than that by RS open field burning. As a result of the open burning of RS in India emitted 592032.52 kg of CO2 equivalents/kg per year, whereas AD of RS contributes 122.86 kg of CO2 equivalents/kg per year. If RS were burned in an open field, its Global Warming Potential would be 493,873 times greater than that of AD. By minimizing GHG emissions and creating sustainable energy from waste, sustainable development, and circular economies are achieved.

Toxicity determination, pollution source delineation, and microbial diversity evaluation of PAHs-contaminated sediments for an urban river.

The Feng-Sang River is a metropolitan river in Kaohsiung City, Taiwan. In this study, Feng-Sang River sediments were analyzed to investigate the distributions and sources of polycyclic aromatic hydrocarbons (PAHs). The Sediment Quality Guidelines (SQGs), potentially carcinogenic PAHs (TEQcarc ), and toxic equivalence quotient (TEQ) were applied to evaluate influences of PAHs on ecosystems and microbial diversities. Results indicate that PAHs concentrations varied between seasons and locations. The concentrations of ∑16 PAHs ranged from 73.6 to 603.8 ng/kg in dry seasons and from 2.3 to 199.3 ng/kg in wet seasons. This could be because of the flushing effect during wet seasons, which caused the movement and dilution of the PAH-contaminated sediments. Diagnostic ratio analysis infers that high PAHs levels were generated by combustion processes and vehicle traffic, and results from multivariate descriptive statistical analysis also demonstrate that the vehicular traffic pollution could be the major emission source of PAHs contamination. Comparisons of PAHs with SQGs indicate that PAHs concentrations in sediment were below the effects range low (ERL) values, and thus, the immediate threat to organisms might not be significant. The diagnostic ratio analyses are effective methods for PAH source appointment. The metagenomic assay results imply that sediments contained essential microbial species with eminent diversity. The detected PAH-degrading bacteria (Desulfatiglans, Dechloromonas, Sphingomonas, Methylobacterium, Rhodobacter, Clostridium, and Exiguobacterium) played a key role in PAHs biotransformation, and Dechloromonas and Rhodobacter had a higher relative abundance. Results of microbial diversity analyses indicate that the contaminated environment induced the changes of governing microbial groups in sediments. PRACTITIONER POINTS: Diagnostic ratio analyses are effective methods for PAHs source appointment. Microbial composition in sediments are highly affected by anthropogenic pollution. Combustion and vehicle traffic contribute to urban river sediments pollution by PAHs. Dechloromonas and Rhodobacter are dominant PAHs-degrading bacteria in sediments.