Robust Soil Water Potential Sensor to Optimize Irrigation in Agriculture.

Extreme weather phenomena are on the rise due to ongoing climate change. Therefore, the need for irrigation in agriculture will increase, although it is already the largest consumer of water, a valuable resource. Soil moisture sensors can help to use water efficiently and economically. For this reason, we have recently presented a novel soil moisture sensor with a high sensitivity and broad measuring range. This device does not measure the moisture in the soil but the water available to plants, i.e., the soil water potential (SWP). The sensor consists of two highly porous (>69%) ceramic discs with a broad pore size distribution (0.5 to 200 µm) and a new circuit board system using a transmission line within a time-domain transmission (TDT) circuit. This detects the change in the dielectric response of the ceramic discs with changing water uptake. To prove the concept, a large number of field tests were carried out and comparisons were made with commercial soil water potential sensors. The experiments confirm that the sensor signal is correlated to the soil water potential irrespective of soil composition and is thus suitable for the optimization of irrigation systems.

Shear modulus and yield stress of foams: contribution of interfacial elasticity.

The link between interfacial elasticity of foaming solutions and the elasticity and yield stress of their aqueous foams is probed for a variety of surfactant, block-copolymer, protein, food, and particle-stabilized (Pickering) foams. We measured interfacial tension σ and interfacial elastic moduli of foaming solutions in dilation E∞ as well as in shear at concentrations suitable for foaming and compared them to the shear modulus and yield stress of corresponding foams normalized by bubbles' Sauter radius R32 and foams' gas volume fraction. The interfacial shear modulus was only measurable for the foaming solutions including proteins or nanoparticles. For these systems the foam shear modulus scaled reasonably well with . The interfacial dilational modulus was accessible for all investigated systems and the foam shear modulus as well as yield stress scaled with a generalized Laplace pressure (σ + 2E∞)/R32. But foams stabilized by nanoparticles or aggregated proteins exhibited even higher shear modulus and yield stress values not captured by the proposed scaling with the generalized Laplace pressure and also show an unexpectedly high dependence of these characteristics on the gas volume fraction. We attribute this to attractive forces between particles and/or structure formation across the lamellae that become increasingly dominant as the lamellae narrow down during foam drainage.

Microrheology imaging of fiber suspensions - a case study for lyophilized collagen I in HCl solutions.

In fiber suspensions with low optical contrast, the in situ characterization of structural properties with conventional microscopy methods fails. However, overlaying subsequent images of multiple particle tracking (MPT) videos including short trajectories usually discarded in MPT analysis allowed for direct visualization of individual fibers and the network structure of lyophilized collagen I (Coll) distributed in hydrochloric acid solutions. MPT yielded a broad distribution of mean square displacements (MSDs). Freely diffusing tracer particles yielded viscosities indicating that, irrespective of concentration, a constant amount of Coll is dissolved in the aqueous phase. Particles found elastically trapped within fibrous Coll structures exhibited a broad range of time-independent MSDs and we propose a structure comprising multiple fiber bundles with dense regions inaccessible to tracers and elastic regions of different stiffness in between. Bulky aggregates inaccessible to the 0.2 µm tracers exist even at low Coll concentrations, a network of slender fibers evolves above the sol-gel transition and these fibers densify with increasing Coll concentration. This novel MPT-based imaging technique possesses great potential to characterize the fiber distribution in and structural properties of a broad range of biological and technical suspensions showing low contrast when imaged with conventional techniques. Thus, MPT imaging and microrheology will help to better understand the effect of fiber distribution and network structure on the viscoelastic properties of complex suspensions.

Interfacial and Foaming Properties of Tailor-Made Glycolipids-Influence of the Hydrophilic Head Group and Functional Groups in the Hydrophobic Tail.

Glycolipids are a class of biodegradable surfactants less harmful to the environment than petrochemically derived surfactants. Here we discuss interfacial properties, foam stability, characterized in terms of transient foam height, gas volume fraction and bubble diameter as well as texture of seven enzymatically synthesized surfactants for the first time. Glycolipids consisting of different head groups, namely glucose, sorbitol, glucuronic acid and sorbose, combined with different C10 acyl chains, namely decanoate, dec-9-enoate and 4-methyl-nonanoate are compared. Equilibrium interfacial tension values vary between 24.3 and 29.6 mN/m, critical micelle concentration varies between 0.7 and 3.0 mM. In both cases highest values were found for the surfactants with unsaturated or branched tail groups. Interfacial elasticity and viscosity, however, were significantly reduced in these cases. Head and tail group both affect foam stability. Foams from glycolipids with sorbose and glucuronic acid derived head groups showed higher stability than those from surfactants with glucose head group, sorbitol provided lowest foam stability. We attribute this to different head group hydration also showing up in the time to reach equilibrium interfacial adsorption. Unsaturated tail groups reduced whereas branching enhanced foam stability compared to the systems with linear, saturated tail. Moreover, the tail group strongly influences foam texture. Glycolipids with unsaturated tail groups produced foams quickly collapsing even at smallest shear loads, whereas the branched tail group yielded a higher modulus than the linear tails. Normalized shear moduli for the systems with different head groups varied in a narrow range, with the highest value found for decylglucuronate.

Deformation of soft particles with controlled elasticity by liquid-liquid interfacial tension.

Herein we report the deformation of PDMS-based particles at a liquid-liquid interface at varying degrees of softness. Direct visualization of the particle adsorption to the interface reveals at least five different modes of deformation from the complete spreading of a polymer resin droplet to a non-deforming, rigid particle.

Bottom-Up Assembly of DNA-Silica Nanocomposites into Micrometer-Sized Hollow Spheres.

Although DNA nanotechnology has developed into a highly innovative and lively field of research at the interface between chemistry, materials science, and biotechnology, there is still a great need for methodological approaches for bridging the size regime of DNA nanostructures with that of micrometer- and millimeter-sized units for practical applications. We report on novel hierarchically structured composite materials from silica nanoparticles and DNA polymers that can be obtained by self-assembly through the clamped hybridization chain reaction. The nanocomposite materials can be assembled into thin layers within microfluidically generated water-in-oil droplets to produce mechanically stabilized hollow spheres with uniform size distributions at high throughput rates. The fact that cells can be encapsulated in these microcontainers suggests that our concept not only contributes to the further development of supramolecular bottom-up manufacturing, but can also be exploited for applications in the life sciences.

Fractal approaches to characterize the structure of capillary suspensions using rheology and confocal microscopy.

The rheological properties of a particle suspension can be substantially altered by adding a small amount of a secondary fluid that is immiscible with the bulk phase. The drastic change in the strength of these capillary suspensions arises due to the capillary forces, induced by the added liquid, leading to a percolating particle network. Using rheological scaling models, fractal dimensions are deduced from the yield stress and from oscillatory strain amplitude sweep data as function of the solid volume fraction. Exponents obtained using aluminum-oxide-based capillary suspensions, with a preferentially wetting secondary fluid, indicate an increase in the particle gel's fractal dimension with increasing particle size. This may be explained by a corresponding relative reduction in the capillary force compared to other forces. Confocal images using a glass model system show the microstructure to consist of compact particle flocs interconnected by a sparse backbone. Thus, using the rheological models two different fractal dimensionalities are distinguished - a lower network backbone dimension (D = 1.86-2.05) and an intrafloc dimension (D = 2.57-2.74). The latter is higher due to the higher local solid volume fraction inside of the flocs compared to the sparse backbone. Both of these dimensions are compared with values obtained by analysis of spatial particle positions from 3D confocal microscopy images, where dimensions between 2.43 and 2.63 are computed, lying between the two dimension ranges obtained from rheology. The fractal dimensions determined via this method corroborate the increase in structural compactness with increasing particle size.

Self-Assembling All-Enzyme Hydrogels for Flow Biocatalysis.

Continuous flow biocatalysis is an emerging field of industrial biotechnology that uses enzymes immobilized in flow channels for the production of value-added chemicals. We describe the construction of self-assembling all-enzyme hydrogels that are comprised of two tetrameric enzymes. The stereoselective dehydrogenase LbADH and the cofactor-regenerating glucose 1-dehydrogenase GDH were genetically fused with a SpyTag or SpyCatcher domain, respectively, to generate two complementary homo-tetrameric building blocks that polymerize under physiological conditions into porous hydrogels. Mounted in microfluidic reactors, the gels show excellent stereoselectivity with near quantitative conversion in the reduction of prochiral ketones along with high robustness under process and storage conditions. The gels function as compartment that retains intermediates thus enabling high total turnover numbers of the expensive cofactor NADP(H).

Physical properties of cytoplasmic intermediate filaments.

Intermediate filaments (IFs) constitute a sophisticated filament system in the cytoplasm of eukaryotes. They form bundles and networks with adapted viscoelastic properties and are strongly interconnected with the other filament types, microfilaments and microtubules. IFs are cell type specific and apart from biochemical functions, they act as mechanical entities to provide stability and resilience to cells and tissues. We review the physical properties of these abundant structural proteins including both in vitro studies and cell experiments. IFs are hierarchical structures and their physical properties seem to a large part be encoded in the very specific architecture of the biopolymers. Thus, we begin our review by presenting the assembly mechanism, followed by the mechanical properties of individual filaments, network and structure formation due to electrostatic interactions, and eventually the mechanics of in vitro and cellular networks. This article is part of a Special Issue entitled: Mechanobiology.

Interaction between Polymeric Additives and Secondary Fluids in Capillary Suspensions.

Capillary suspensions are ternary systems including a solid and two liquid phases representing a novel formulation platform for pastes with unique processing and end-use properties. Here we have investigated aqueous suspensions of non-Brownian graphite particles including different polymers commonly used as thickening agents or binders in paste formulations. We have studied the interaction between these additives and organic solvents in order to elucidate its effect on the characteristic formation of a particle network structure in corresponding ternary capillary suspension systems. Organic solvents with different polarity have been employed, and in the presence of nonadsorbing poly(ethylene oxide), all of them, whether they preferentially wet the graphite surface or not, induce the formation of a network structure within the suspension as indicated by a strong change in rheological properties. However, when the adsorbing polymers carboxymethylcellulose and poly(vinylpyrrolidone) are included, the drastic change in rheological behavior occurs only when polar organic solvents are used as secondary liquids. Obviously, these solvents can form pendular bridges, finally resulting in a sample-spanning particle network. Vibrational sum frequency spectroscopy provides evidence that these polar liquids remove the adsorbed polymer from the graphite particles. In contrast, nonpolar and nonwetting solvents do not force polymer desorption. In these cases, the formation of a percolating network structure within the suspensions is presumably prevented by the strong steric repulsion among graphite particles, not allowing for the formation of particle clusters encapsulating the secondary liquid. Accordingly, polymeric additives and secondary fluids have to be carefully selected in capillary suspension formulations, then offering a new pathway to customize paste formulations. The polymer may serve to adjust an appropriate viscosity level, and the capillary bridging induces the desired degree of shear thinning. Alternatively, the polymer may be selected with respect to its binding properties in the final dry product, and capillary bridging may be used to control the flow and processing behavior of the wet paste.

Size-Limited Penetration of Nanoparticles into Porcine Respiratory Mucus after Aerosol Deposition.

We investigated the rheological properties and the penetration of differently sized carboxylated nanoparticles in pig pulmonary mucus, on different distance and time scales. Nanoparticles were either mechanically mixed into the mucus samples or deposited as an aerosol, the latter resembling a more physiologically relevant delivery scenario. After mechanical dispersion, 500 nm particles were locally trapped; a fraction of carboxylated tracer particles of 100 or 200 nm in diameter could however freely diffuse in these networks over distances of approximately 20 µm. In contrast, after aerosol deposition on top of the mucus layer only particles with a size of 100 nm were able to penetrate into mucus, suggesting the presence of smaller pores at the air-mucus interface compared to within mucus. These findings are relevant to an understanding of the fate of potentially harmful aerosol particles, such as pathogens, pollutants, and other nanomaterials after incidental inhalation, as well as for the design of pulmonary drug delivery systems.

Restructuring and aging in a capillary suspension.

The rheological properties of capillary suspensions, suspensions with small amounts of an added immiscible fluid, are dramatically altered with the addition of the secondary fluid. We investigate a capillary suspension to determine how the network ages and restructures at rest and under applied external shear deformation. The present work uses calcium carbonate suspended in silicone oil (11 % solids) with added water as a model system. Aging of capillary suspensions and their response to applied oscillatory shear is distinctly different from particulate gels dominated by the van der Waals forces. The suspensions dominated by the capillary force are very sensitive to oscillatory flow, with the linear viscoelastic regime ending at a deformation of only 0.1% and demonstrating power-law aging behavior. This aging persists for long times at low deformations or for shorter times with a sudden decrease in the strength at higher deformations. This aging behavior suggests that the network is able to rearrange and even rupture. This same sensitivity is not demonstrated in shear flow where very high shear rates are required to rupture the agglomerates returning the apparent viscosity of capillary suspensions to the same viscosity as for the pure vdW suspension. A transitional region is also present at intermediate water contents wherein the material response depends very strongly on the type, strength, and duration of the external forcing.

Thermal-Rectified Gradient Porous Polymeric Film for Solar-Thermal Regulatory Cooling.

Solar-thermal regulation concerning thermal insulation and solar modulation is pivotal for cooling textiles and smart buildings. Nevertheless, a contradiction arises in balancing the demand to prevent external heat infiltration with the efficient dissipation of excess heat from enclosed spaces. Here, a concentration-gradient polymerization strategy is presented for fabricating a gradient porous polymeric film comprising interconnected polymeric microspheres. This method involves establishing an electric field-driven gradient distribution of charged crosslinkers in the precursor solution, followed by subsequent polymerization and freeze-drying processes. The resulting porous film exhibits a significant porosity gradient along its thickness, leading to exceptional unidirectional thermal insulation capabilities with a thermal rectification factor of 21%. The gradient porous film, with its thermal rectification properties, effectively reconciles the conflicting demands of diverse thermal conductivity for cooling unheated and spontaneously heated enclosed spaces. Consequently, the gradient porous film demonstrates remarkable enhancements in solar-thermal management, achieving temperature reductions of 3.0 and 4.1 °C for unheated and spontaneously heated enclosed spaces, respectively, compared to uniform porous films. The developed gradient-structured porous film thus holds promise for the development of thermal-rectified materials tailored to regulate solar-thermal conditions within enclosed environments.

A Multifunctional Nanostructured Hydrogel as a Platform for Deciphering Niche Interactions of Hematopoietic Stem and Progenitor Cells.

For over half a century, hematopoietic stem cells (HSCs) have been used for transplantation therapy to treat severe hematologic diseases. Successful outcomes depend on collecting sufficient donor HSCs as well as ensuring efficient engraftment. These processes are influenced by dynamic interactions of HSCs with the bone marrow niche, which can be revealed by artificial niche models. Here, a multifunctional nanostructured hydrogel is presented as a 2D platform to investigate how the interdependencies of cytokine binding and nanopatterned adhesive ligands influence the behavior of human hematopoietic stem and progenitor cells (HSPCs). The results indicate that the degree of HSPC polarization and motility, observed when cultured on gels presenting the chemokine SDF-1α and a nanoscale-defined density of a cellular (IDSP) or extracellular matrix (LDV) α4ß1 integrin binding motif, are differently influenced on hydrogels functionalized with the different ligand types. Further, SDF-1α promotes cell polarization but not motility. Strikingly, the degree of differentiation correlates negatively with the nanoparticle spacing, which determines ligand density, but only for the cellular-derived IDSP motif. This mechanism potentially offers a means of predictably regulating early HSC fate decisions. Consequently, the innovative multifunctional hydrogel holds promise for deciphering dynamic HSPC-niche interactions and refining transplantation therapy protocols.

pH effects on the molecular structure of ß-lactoglobulin modified air-water interfaces and its impact on foam rheology.

Macroscopic properties of aqueous ß-lactoglobulin (BLG) foams and the molecular properties of BLG modified air-water interfaces as their major structural element were investigated with a unique combination of foam rheology measurements and interfacial sensitive methods such as sum-frequency generation and interfacial dilatational rheology. The molecular structure and protein-protein interactions at the air-water interface can be changed substantially with the solution pH and result in major changes in interfacial dilational and foam rheology. At a pH near the interfacial isoelectric point BLG molecules carry zero net charge and disordered multilayers with the highest interfacial dilatational elasticity are formed at the air-water interface. Increasing or decreasing the pH with respect to the isoelectric point leads to the formation of a BLG monolayer with repulsive electrostatic interactions among the adsorbed molecules which decrease the interfacial dilational elasticity. The latter molecular information does explain the behavior of BLG foams in our rheological studies, where in fact the highest apparent yield stresses and storage moduli are established with foams from electrolyte solutions with a pH close to the isoelectric point of BLG. At this pH the gas bubbles of the foam are stabilized by BLG multilayers with attractive intermolecular interactions at the ubiquitous air-water interfaces, while BLG layers with repulsive interactions decrease the apparent yield stress and storage moduli as stabilization of gas bubbles with a monolayer of BLG is less effective.

Targeted micro-heterogeneity in bioinks allows for 3D printing of complex constructs with improved resolution and cell viability.

Three-dimensional bioprinting is an evolving versatile technique for biomedical applications. Ideal bioinks have complex micro-environment that mimic human tissue, allow for good printing quality and provide high cell viability after printing. Here we present two strategies for enhancing gelatin-based bioinks heterogeneity on a 1-100µm length scale resulting in superior printing quality and high cell viability. A thorough spatial and micro-mechanical characterization of swollen hydrogel heterogeneity was done using multiple particle tracking microrheology. When poly(vinyl alcohol) is added to homogeneous gelatin gels, viscous inclusions are formed due to micro-phase separation. This phenomenon leads to pronounced slip and superior printing quality of complex 3D constructs as well as high human hepatocellular carcinoma (HepG2) and normal human dermal fibroblast (NHDF) cell viability due to reduced shear damage during extrusion. Similar printability and cell viability results are obtained with gelatin/nanoclay composites. The formation of polymer/nanoclay clusters reduces the critical stress of gel fracture, which facilitates extrusion, thus enhancing printing quality and cell viability. Targeted introduction of micro-heterogeneities in bioinks through micro-phase separation is an effective technique for high resolution 3D printing of complex constructs with high cell viability. The size of the heterogeneities, however, has to be substantially smaller than the desired feature size in order to achieve good printing quality.

A holistic view on the role of egg yolk in Old Masters' oil paints.

Old Masters like Botticelli used paints containing mixtures of oils and proteins, but "how" and "why" this was done is still not understood. Here, egg yolk is used in combination with two pigments to evaluate how different repartition of proteinaceous binder can be used to control the flow behavior as well as drying kinetics and chemistry of oil paints. Stiff paints enabling pronounced impasto can be achieved, but paint stiffening due to undesired uptake of humidity from the environment can also be suppressed, depending on proteinaceous binder distribution and colloidal paint microstructure. Brushability at high pigment loading is improved via reduction of high shear viscosity and wrinkling can be suppressed adjusting a high yield stress. Egg acts as antioxidant, slowing down the onset of curing, and promoting the formation of cross-linked networks less prone to oxidative degradation compared to oil alone, which might improve the preservation of invaluable artworks.

Phase-Change-Enabled, Rapid, High-Resolution Direct Ink Writing of Soft Silicone.

Soft silicone is an ideal flexible material for application, e.g., in soft robotics, flexible electronics, bionics, or implantable biomedical devices. However, gravity-driven sagging, filament stretching, and deformation can cause inevitable defects during rapid manufacturing, making it hard to obtain complex, high-resolution 3D silicone structures with direct ink writing (DIW) technology. Here, rapid DIW of soft silicone enabled by a phase-change-induced, reversible change of the ink's hierarchical microstructure is presented. During printing, the silicone-based ink, containing silica nanoparticles and wax microparticles, is extruded from a heated nozzle into a cold environment under controlled stress. The wax phase change (solid-liquid-solid) during printing rapidly destroys and rebuilds the particle networks, realizing fast control of the ink flow behavior and printability. This high-operating-temperature DIW method is fast (maximum speed ≈3100 mm min-1 ) and extends the DIW scale range of soft silicone. The extruded filaments have small diameters (50 ± 5 µm), and allow for large spans (≈13-fold filament diameter) and high aspect ratios (≈1), setting a new benchmark in the DIW of soft silicone. Printed silicone structures exhibit excellent performance as flexible sensors, superhydrophobic surfaces, and shape-memory bionic devices, illustrating the potential of the new 3D printing strategy.

Giant Functional Properties in Porous Electroceramics through Additive Manufacturing of Capillary Suspensions.

Dedicated hierarchical structuring of functional ceramics can be used to shift the limits of functionality. This work presents the manufacturing of highly open porous, hierarchically structured barium titanate ceramics with 3-3 connectivity via direct ink writing of capillary suspension-type inks. The pore size of the printed struts (∼1 µm) is combined with a printed mesostructure (∼100 µm). The self-organized particle network, driven by strong capillary forces in the ternary solid/fluid/fluid ink, results in a high strut porosity, and the distinct flow properties of the ink allow for printing high strut size to pore size ratios, resulting in total porosities >60%. These unique and highly porous additive manufactured log-pile structures with closed bottom and top layers enable tailored dielectric and electromechanical coupling, resulting in an energy harvesting figure of merit FOM33 more than four times higher than any documented data for barium titanate. This clearly demonstrates that combining additive manufacturing of capillary suspensions in combination with appropriate sintering allows for creation of complex architected 3D structures with unprecedented properties. This opens up opportunities in a broad variety of applications, including electromechanical energy harvesting, electrode materials for batteries or fuel cells, thermoelectrics, or bone tissue engineering with piezoelectrically stimulated cell growth.

Comparative study on interfacial and foaming properties of glycolipids in relation to the gas applied for foam generation.

Glycolipids are biosurfactants with a wide range of structural diversity. They are biodegradable, based on renewables, ecocompatible and exhibit high surface activity. Still, studies comparing glycolipids and conventional surfactants in terms of interfacial properties and foaming performance are lacking. Here, we compared interfacial and foaming properties of microbial and enzymatically synthesized glycolipids to those of the widely-used, conventional surfactant sodium dodecyl sulfate (SDS). The enzymatically produced sorbose monodecanoate, as well as microbially produced di-rhamno-di-lipids exhibited high foam stabilizing properties, similar to those of SDS. However, sophorolipid and mono-rhamno-di-lipids did not produce metastable foams. An appropriate selection of head and tail groups depending on the application of interest is therefore necessary. Then, glycolipids can serve as an ecofriendly and efficient alternative to petroleum-based surfactants, even at substantially lower concentrations than e.g. SDS. Moreover, the influence of three foaming gases on the foaming properties of the glycolipids was evaluated. Slightly higher foam stability and lower coarsening rates were determined for sorbose monodecanoate when using nitrogen as the foaming gas instead of air. Foams generated with carbon dioxide were not metastable, no matter which surfactant was used.