Suppressed Droplet Splashing on Positively Skewed Surfaces for High-Efficiency Evaporation Cooling.

Two types of functional surfaces with the same roughness but completely different surface topographies are prepared, namely positively skewed surfaces filled with micropillar arrays (Sa ≈4.4 µm, Ssk >0) and negatively skewed surfaces filled with microcavity arrays (Sa ≈4.4 µm, Ssk <0), demonstrating promoting droplet splashing. Remarkably, the critical Weber number for generating satellite droplets on the negatively skewed surfaces is significantly lower than that on the positively skewed surfaces, indicating that the negatively skewed surface with microcavity arrays is more likely to promote droplet splashing. It is mainly attributed to the fact that air on the negatively skewed surface can make the liquid film take on a Cassie-Baxter state on the surface so that the stabilizing capillary force of the liquid film exceeds the destabilizing stress of the air film. Moreover, the surface topography promoting droplet spreading and the mechanical properties of three-phase moving contact lines are analyzed from the perspective of microscopic interface mechanics. Finally, it is demonstrated the designed positively skewed surfaces can be employed for large-area heat dissipation by means of high-efficiency evaporation.

Enhancing color saturation in photonic glasses through optimized absorption.

Photonic glasses, isotropically assembled nanoparticles with short-range correlation, can produce angle independent structural colors. They show broader reflectance spectra and lower saturated colors, compared to photonic crystals. Low color saturation creates barriers for photonic glasses to be used for coatings, cosmetics, and colors. Broadband absorbing materials are commonly used to absorb incoherently scattered light to enhance the saturation. However, there is limited understanding on how the absorption quantitatively affects the colors of photonic glasses. To this end, we here use a validated Monte Carlo-based multiple scattering model to investigate how absorption impacts the reflectance spectra in photonic glasses. We show that the color saturation can be maximized with an optimal level of absorption regardless of sample thickness or refractive index contrast between particles and matrix. We quantitatively demonstrate that the multiple scattering is largely reduced with the optimal absorption level and the reflectance is dominantly contributed by the single scattering. The optimal absorption occurs when the sample absorption mean free path is comparable to the transport mean free path, which offers a guidance on how much absorbing material is needed for creating highly saturated photonic glasses. This work will not only pave ways for pushing applications of angle-independent structural colors, but also improve our understanding of light scattering and absorption in short-range correlated disordered systems.

Armored Superhydrophobic Surfaces with Excellent Drag Reduction in Complex Environmental Conditions.

Superhydrophobic surfaces (SHSs) have possibilities for achieving significantly reduced solid-liquid frictional drag in the marine sector due to their excellent water-repelling properties. Although the stability of SHSs plays a key role in drag reduction, little consideration was given to the effect of extreme environments on the ability of SHSs to achieve drag reduction underwater, particularly when subjected to acidic conditions. Here, we propose interconnected microstructures to protect superhydrophobic coatings with the aim of enhancing the stability of SHSs in extreme environments. The stability of armored SHSs (ASHSs) was demonstrated by the contact angle and bounce time of droplets on superhydrophobic surfaces treated by various methods, resulting in an ASHS surface with excellent stability under extreme environmental conditions. Additionally, inspired by microstructures protecting superhydrophobic nanomaterials from frictional wear, the armored superhydrophobic spheres (ASSPs) were designed to explain from theoretical and experimental perspectives why ASSPs can achieve sustainable drag reduction and demonstrate that the ASSPs can achieve drag reduction of over 90.4% at a Reynolds number of 6.25 × 104 by conducting water entry experiments on spheres treated in various solutions. These studies promote a fundamental understanding of what drives the application of SHSs under extreme environmental conditions and provide practical strategies to maximize frictional drag reduction.

Characterising baseflow signature variability in the Yellow River Basin.

Baseflow is pivotal in maintaining catchment ecological health and improving sustainable economic development. The Yellow River Basin (YRB) is northern China's most important water supplier. However, it faces water shortage due to synergistic effects between natural conditions and anthropogenic activities. Investigating baseflow characteristics quantitively is, therefore, beneficial to promoting the sustainable development of the YRB. In this study, daily ensemble means baseflow data derived from four revised baseflow separation algorithms (i.e., the United Kingdom Institute of Hydrology (UKIH), Lyne-Hollick, Chapman-Maxwell, and Eckhardt methods) - was obtained from 2001 to 2020. Thirteen baseflow dynamics signatures were extracted to investigate baseflow spatiotemporal variations and their determinants across the YRB. The main findings were: (1) There were significant spatial distribution patterns of baseflow signatures, and most signatures had higher values in upstream and downstream reaches than in the middle reaches. There were also mixing patterns with higher values in middle and downstream reaches simultaneously. (2) The magnitude of temporal variation in baseflow signatures was most strongly correlated with catchment terrain (r = -0.4), vegetation growth (r > 0.3), and cropland coverage (r > 0.4). (3) There was a strong synergistic effect of multiple factors (e.g., soil textures, precipitation and vegetation conditions) on baseflow signature values. This study provided a heuristic evaluation of baseflow characteristics in the YRB, contributing to water resources management in the YRB and similar catchments.

Nitric Acid-Treated Blue Coke-Based Activated Carbon's Structural Characteristics and Its Application in Hexavalent Chromium-Containing Wastewater Treatment.

This study primarily focused on the efficient transformation of low-priced blue coke powder into a high-capacity adsorbent and aimed to address the pollution issue of hexavalent chromium (Cr (VI))-laden wastewater and to facilitate the effective utilization of blue coke powder. A two-step method was utilized to fabricate a blue coke-based nitric acid-modified material (LCN), and the impact of nitric acid modification on the material's structure and its efficacy in treating Cr (VI)-contaminated wastewater was evaluated. Our experimental results illustrated that, under identical conditions, LCN exhibited superior performance for Cr (VI) treatment compared to the method employing only potassium hydroxide (LCK). The specific surface area and pore volume of LCN were 1.39 and 1.36 times greater than those of LCK, respectively. Further chemical composition analysis revealed that the functional group structure on the LCN surface was more conducive to Cr (VI) adsorption. The highest amount of Cr (VI) that LCN could bind was measured at 181.962 mg/g at 318 K. This was mostly due to chemisorption, which is dominated by redox reactions. The Cr (VI) removal process by LCN was identified to be a spontaneous, exothermic, and entropy-increasing process. Several tests on recycling and reuse showed that LCN is a stable and effective chromium-containing wastewater adsorbent, showing that it could be used in many situations.

Short-term effects of the toxic component of traffic-related air pollution (TRAP) on lung function in healthy adults using a powered air purifying respirator (PAPR).

Short-term exposure to traffic-related air pollution (TRAP) are associated with reduced lung function. However, TRAP is a mixture of various gaseous pollutants and particulate matter (PM), and therefore it is unknown that which components of TRAP are responsible for the respiratory toxicity. Using a powered air-purifying respirator (PAPR), we conducted a randomized, double-blind, crossover trial in which 40 adults were exposed to TRAP for 2 h at the sidewalk of a busy road. During the exposure, the participants wore the PAPR fitted with a PM filter, a PM and volatile organic compounds (VOCs) filter, or a sham filter (no filtration, Sham mode). The participants were blinded to the type of filter in their PAPR, and experienced three exposures, once for each intervention mode in random order. We measured two lung function measures (forced expiratory volume in 1 s [FEV1] and forced vital capacity [FVC]) and an airway inflammation marker (fraction of exhaled nitric oxide [FENO]) before and immediately after each exposure, and further measured them at different time periods after exposure. We applied linear mixed effect models to estimate the effects of the interventions on the changes of lung function from baseline values after controlling for other covariates. Compared to baseline, exposing to TRAP decreased FEV1 and FVC, and increased FEV1/FVC and FENO in all three intervention modes. The mixed models showed that with the sham mode as reference, lung function and airway inflammation post exposure were significantly improved by filtering both PM and VOCs, but marginally affected by filtering only PM. In conclusion, the VOCs component of TRAP is responsible for the reduction in lung function caused by short-term exposure to TRAP. However, the result needs to be interpreted cautiously before further verified by laboratory experiment using purely isolated component(s) of TRAP.

Research on the performance of modified blue coke in adsorbing hexavalent chromium.

To solve the issue of hexavalent chromium (Cr(VI)) contamination in water bodies, blue coke powder (LC) was chemically changed using potassium hydroxide to create the modified material (GLC), which was then used to treat a Cr(VI)-containing wastewater solution. The differences between the modified and unmodified blue coke's adsorption characteristics for Cr(VI) were studied, and the impact of pH, starting solution concentration, and adsorption period on the GLC's adsorption performance was investigated. The adsorption behavior of the GLC was analyzed using isothermal adsorption models, kinetic models, and adsorption thermodynamic analysis. The mechanism of Cr(VI) adsorption by the GLC was investigated using characterization techniques such as Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscope (FE-SEM), X-Ray Diffraction (XRD), and X-Ray Photoelectron Spectroscopy (XPS). With the biggest difference in removal rate at pH = 2, which was 2.42 times that of LC, batch adsorption experiments revealed that, under the same adsorption conditions, the GLC always performed better than LC. With a specific surface area that was three times that of LC and an average pore diameter that was 0.67 times that of LC, GLC had a more porous structure than LC. The alteration significantly increased the number of hydroxyls on the surface of GLC by altering the structural makeup of LC. The ideal pH for removing Cr(VI) was 2, and the ideal GLC adsorbent dosage was 2.0 g/L. Pseudo-second-order kinetic (PSO) model and Redlich-Peterson (RP) model can effectively describe the adsorption behavior of GLC for Cr(VI). Physical and chemical adsorption work together to remove Cr(VI) by GLC in a spontaneous, exothermic, and entropy-increasing process, with oxidation-reduction processes playing a key role. GLC is a potent adsorbent that can be used to remove Cr(VI) from aqueous solutions.

Capillary rise behavior of lubricant in micropores with spiral bulge structures.

The highly efficient exudation of lubricant in porous self-lubricating materials significantly influences the formation of self-lubricating films. In this paper, micropores with inner spiral bulge structures are considered, and their influence on the capillary behaviors of the lubricant is discussed to reveal the capillary rising mechanism. The results show that the Taylor capillary lift phenomenon is produced in the spiral bulge structure of the micropore, and the capillary lift force is enhanced. The spiral structure decreases the effective diameter of micropores. The magnitudes of the pressure and velocity in the spiral structure pores are larger than those in smooth pores. The liquid in the upper part of the micropores forms a velocity vortex during its upward rotation along the spiral channel, which promotes the capillary rising behavior. For smaller pitches, the velocity vortex increases, and the rising speed of the lubricant grows. The inner spiral bulge structure gives the micropores an excellent capillary rising ability. The quantitative characterization and mechanism reveal that the capillary rising behavior can be used to guide the bionic designs of pores in self-lubricating materials.

Fused Deposition Modeling and Characterization of Heat Shape Memory Poly(lactic) Acid-Based Porous Vascular Scaffold.

Shape memory polymers have received widespread attention from researchers because of their low density, shape variety, responsiveness to the environment, and transparency. This study deals with heat-shape memory polymers (SMPs) based on polylactic acid (PLA) for designing and fabricating a novel porous vascular scaffold to treat vascular restenosis. The solid isotropic material penalization method (SIMP) was applied to optimize the vascular scaffolds. Based on the torsional torque loading of Hyperworks Optistruct and the boundary conditions, the topological optimization model of a vascular scaffold unit was established. Forward and reverse hybrid modeling technology was applied to complete the final stent structure's assembly. The glass transition temperature for the present SMPs is 42.15 °C. With the increase in temperature, the ultimate tensile strength of the SMPs is reduced from 29.5 MPa to 11.6 MPa. The maximum modulus at room temperature was around 34 MPa. Stress relaxation curves show that the material classification is a "thermoset" polymer. The superb mechanical properties, the transition temperature of the SMPs, and the recovery ratio made it a feasible candidate for a vascular scaffold. A circular tube based on the shape memory polymers was presented as an example for analyzing the recovery ratio in an unfolding state. A higher recovery ratio was obtained at a temperature of 65 °C with a tube thickness of 2 mm. Finally, the proposed porous vascular scaffold was successfully fabricated, assessed, and compared with the original and previously developed vascular scaffolds. The proposed scaffold structure regains its initial shape with a recovery ratio of 98% (recovery temperature of 47 °C) in 16 s. The tensile strength, Young's modulus, and bending strength of the proposed scaffold were 29.5 MPa, 695.4 MPa, and 6.02 MPa, respectively. The results showed that the proposed scaffold could be regarded as a potential candidate for a vascular implantation.

Integrating ambient carbonyl compounds provides insight into the constrained ozone formation chemistry in Zibo city of the North China Plain.

Quantifying the impact of carbonyl compounds (carbonyls) on ozone (O3) photochemical formation is crucial to formulating targeted O3 mitigation strategies. To investigate the emission source of ambient carbonyls and their integrated observational constraint on the impact of O3 formation chemistry, a field campaign was conducted in an industrial city (Zibo) of the North China Plain from August to September 2020. The site-to-site variations of OH reactivity for carbonyls were in accordance with the sequence of Beijiao (BJ, urban, 4.4 s-1) > Xindian (XD, suburban, 4.2 s-1) > Tianzhen (TZ, suburban, 1.6 s-1). A 0-D box model (MCMv3.3.1) was applied to assess the O3-precursor relationship influenced by measured carbonyls. It was found that without carbonyls constraint, the O3 photochemical production of the three sites was underestimated to varying degrees, and the biases of overestimating the VOC-limited degree were also identified through a sensitivity test to NOx emission changes, which may be associated with the reactivity of carbonyls. In addition, the results of the positive matrix factorization (PMF) model indicated that the main source of aldehydes and ketones was secondary formation and background (81.6% for aldehydes, 76.8% for ketones), followed by traffic emission (11.0% for aldehydes, 14.0% for ketones). Incorporated with the box model, we found that biogenic emission contributed the most to the O3 production at the three sites, followed by traffic emission as well as industry and solvent usage. Meanwhile, the relative incremental reactivity (RIR) values of O3 precursor groups from diverse VOC emission sources featured consistencies and differences at the three sites, which further highlights the importance of the synergetic mitigation of target O3 precursors at regional and local scales. This study will help to provide targeted policy-guiding O3 control strategies for other regions.

[Photochemical Mechanism and Control Strategy Optimization for Summertime Ozone Pollution in an Industrial City in the North China Plain].

To investigate the characteristics and formation mechanism of ozone (O3) pollution in an industrial city, an extensive one-month field campaign focusing on O3 and its precursors (e.g., volatile organic compounds[VOC] and nitrogen oxides[NOx]) was conducted in Zibo City, a highly industrializd city in the North China Plain, in June 2021. The 0-D box model incorporating the latest explicit chemical mechanism (MCMv3.3.1) was applied using an observation dataset (e.g., VOC, NOx, HONO, and PAN) as model contraints to explore the optimal reduction strategy for O3 and its precursors. The results showed that ① during high-O3 episodes, stagnant weather conditions with high temperature and solar radiation as well as low relative humidity were observed, and oxygenated VOCs and alkenes from anthropogenic VOCs contributed the most to the total ozone formation potential and OH reactivity (k·OH). ② The in-situ O3 variation was primarily affected by local photochemical production and export process horizontal to downwind areas or vertical to the upper layer. The reduction in local emissions was essential to alleviate O3 pollution in this region. ③ During high-O3 episodes, high concentrations of ·OH (10×106 cm-3) and HO2· (14×108 cm-3) radical drove and generated a high O3 production rate (daytime peak value reached 36×10-9 h-1). The reaction pathways of HO2·+NO and ·OH+NO2 contributed the most to the in-situ gross Ox photochemical production (63%) and photochemical destruction (50%), respectively. ④ Compared to those during low-O3 episodes, the photochemical regimes during high-O3 episodes were more inclined to be considered as the NOx-limited regime. Detailed mechanism modeling based on multiple scenarios further suggested that the synergic emission reduction strategy of NOx and VOC, while focusing on NOx emission alleviation, would be practical options for controlling local O3 pollutions. This method could also provide policy-related guidance for the precise O3 pollution prevention and control in other industrialized Chinese cities.

Investigation of water-soluble organic constituents and their spatio-temporal heterogeneity over the Tibetan Plateau.

Investigating the migration and transformation of carbonaceous and nitrogenous matter in the cryosphere areas is crucial for understanding global biogeochemical cycle and earth's climate system. However, water-soluble organic constituents and their transformation in multiple water bodies are barely investigated. Water-soluble organic carbon (WSOC) and organic nitrogen (WSON), and particulate black carbon (PBC) in multiple types of water bodies in eastern Tibetan Plateau (TP) cryosphere for the first time have been systematically investigated. Statistical results exhibited that from south to north and from east to west of this region, WSOC concentrations in alpine river runoff were gradually elevated. WSOC and nitrogenous matter in the alpine river runoff and precipitation in the glacier region presented distinct seasonal variations. WSON was the dominant component (63.4%) of water-soluble total nitrogen in precipitation over high-altitude southeastern TP cryosphere. Water-soluble carbonaceous matter dominated the carbon cycle in the TP cryosphere, but particulate carbonaceous matter in the alpine river runoff had a small fraction of the cryospheric carbon cycle. Analysis of optical properties illustrated that PBC had a much stronger light absorption ability (MAC-PBC: 2.28 ± 0.37 m2 g-1) than WSOC in the alpine river runoff (0.41 ± 0.26 m2 g-1). Ionic composition was dominated by SO42-, NO3-, and NH4+ (average: 45.13 ± 3.75%) in the snow of glaciers, implying important contribution of (fossil fuel) combustion sources over this region. The results of this study have essential implications for understanding the carbon and nitrogen cycles in high altitude cryosphere regions of the world. Future work should be performed based on more robust in-situ observations and measurements from multiple environmental medium over the cryosphere areas, to ensure ecological protection and high-quality development of the high mountain Asia.

Identifying active concentrations of biopolymers for enhancing membrane nanofiltration performance: From bench-scale tests to real production considerations.

In the last decades, membrane-based nanofiltration (NF) technique has been widely applied for safe and high-quality drinking water production worldwide. NF membrane fouling has become one of the main obstacles in its application due to high operation cost, and thus numerous efforts have been made. However, there is still a large disconnect between academic findings and their applications. Hence, novel approaches for further exploitation and application are required based on feasibility of implementation. In this work, an optimized design of membrane-based NF plants was proposed, inspired by natural biopolymers present in feed water of NF unit. Specifically, we found beneficial functions of biopolymers, including NF membrane fouling alleviation and effluent quality improvement; these advantages could only be "activated" under a certain concentration range of biopolymers (0-1 mg C/L here), and less or more is not acceptable. This indicated that a NF unit is better to follow a microfiltration (MF) (instead of ultrafiltration (UF) which removes biopolymers) process during which natural biopolymers could be remained; also, this approach is suggested to be valid across different seasons when biopolymers' concentrations could be controlled within an "activated" range by mixing MF and UF permeates. Furthermore, three representative reference biopolymers with different, confirmed spatial structures and molecular weight (MW) were used to elucidate the micro-level functions of natural biopolymers on NF membranes, suggesting that cake layer structures shaped by various biopolymers determine the resulting NF performance. Overall, this innovative proposal is expected to be considered and adopted towards more energy-efficient NF technology for drinking water supply.

Design of co-continuous structure of cellulose/PAA-based alkaline solid polyelectrolyte for flexible zinc-air battery.

In order to prepare high ionic conductivity and robust mechanical properties of alkaline solid polyelectrolyte (ASPE) for applications in flexible wearable devices, a co-continuous structure membrane was designed using in-situ polymerization to introduce cross-linked polyacrylic acid (N-PAA) into the cellulose network constructed by regenerated degreasing cotton (RDC). The resultant ASPE membrane showed high ionic conductivity (430 mS·cm-1 at 25 °C), strong mechanical properties, and excellent alkaline stabilities, proving the viability of cellulose for use in energy storage systems. Surprisingly, the sandwich-shaped zinc-air battery assembled using RDC/N-PAA/KOH membranes as electrolytes exhibits superior values of cycling stability, discharge time, specific capacity (731.5 mAh·g-1), peak power density (40.25 mW·cm-2), and mechanical flexibility. Even under bending conditions, the zinc-air batteries still possess stable energy supply performance, suggesting this novel solid polyelectrolyte has promising application for wearable technology.

Temporal evolution of the hydromechanical properties of soil-root systems in a forest fire in China.

Plant roots generally enhance soil strength and stabilize slopes through hydro-mechanical effects, especially in forested areas prone to shallow slope failure. Forest fires can severely weaken the hydro-mechanical contribution of roots to slopes, however, the hydro-mechanical characteristics of soil-root systems (SRS) affected by wildfire remain poorly understood. To obtain insight into the post-fire hydro-mechanical characteristics of SRS, a subalpine conifer forested area in Sichuan Province, China that suffered a wildfire on March 30, 2019 was continuously monitored over two consecutive years. Samples from zones with different degrees of burn severity were collected and tests both for roots and SRS were performed. The results revealed a substantial decline in root number, which decreased by 46%-58% two years after the wildfire in the medium- and high-severity areas. The tensile strength tests indicated a reduction of root tensile strength by 36%-47% for roots with diameters less than 2 mm. The shear strength of the SRS determined from saturated direct shear tests strongly and had degraded by 55%-82% two years after the wildfire because of root death and reduced root reinforcement. The results of hydraulic conductivity tests over the same time period indicated an abrupt reduction of SRS hydraulic conductivity within several months after the fire owing to ash clogging and the formation of a hydrophobic layer. After more time had elapsed, however, hydraulic conductivity had increased unexpectedly by a factor of 2.2-3.2 greater than that of unburned soil. We attribute this observation to the formation of macropore flow pathways from decayed roots, which was observed by scanning electron microscopy. The findings presented here provide important insight into the temporal changes of the hydro-mechanical characteristics of SRS in burned areas and their associated mechanisms and could be a useful reference to better evaluate post-wildfire stability of subalpine conifer forest in similar environmental conditions.

[Size Distribution and Source Appointment of Road Particles During Winter in Tianjin].

The significant role of traffic emissions mixed from various sources in urban air pollution has been widely recognized. However, the corresponding contributions to the roadside particle distribution are poorly understood due to the mixed impacts of various sources. Particle number concentrations of different sizes at the roadside in Nankai District of Tianjin were continuously monitored using a portable aerosol particle spectrometer during the morning rush hour (07:30-09:20) from Nov. 9, 2018 to Jan. 6, 2019. Characteristic and influencing factors of particle size distributions were discussed combined with temperature and relative humidity data, while potential sources of particles at the roadside were identified based on size distribution analysis. The results showed that the average total particle number concentrations were 502 cm-3, and the concentrations of the accumulation mode and coarse mode were 500 cm-3 and 2 cm-3, respectively. The distribution of number concentrations at the roadside was unimodal and primarily concentrated at 0.25-0.50 µm, with peak sizes at 0.28-0.30 µm. The same distribution trend of particle number concentration and difference in the concentration in the same segment size were observed at different periods. Vehicle activity level was the main influencing factor of road particulate matter concentration on different weekdays; the probability of the high value of road particulate matter concentration was reduced by a reasonable combination of the vehicle tail numbers. Temperature and relative humidity were both found to be positively correlated with the number concentration of particles. With the increase in temperature and relative humidity, the total and peak particle number concentration showed an overall upward trend. In addition, the peak particle size increased from 0.28-0.30 µm to 0.35-0.40 µm when relative humidity was higher than 80%. Three sources, including road dust, brake and tire wear, and the aging particles from vehicle exhaust, were identified using positive matrix factorization in this study. Road dust contributed 8.6% of the total number concentration, which mainly consisted of particles with sizes above 5.00 µm. Brake and tire wear contributed 2.8% of the total number concentration of particles with a size range of 0.80-4.00 µm. The aging particles from vehicle exhaust contributed the most (88.5%), with a peak at 0.25-0.65 µm. The sources of roadside particles were mainly related to vehicle activity, whereas temperature and relative humidity also affected the particle number size distribution.

Composite Polymer Anion Exchange Membranes with Sandwich Structure and Improved Performance for Zn-Air Battery.

In this study, we fabricated a composite polymer anion exchange membrane (AEM) with a sandwich structure. This prepared AEM demonstrated high ionic conductivity (0.25 Scm-1), excellent alkali resistance (8 M KOH), and good mechanical properties (tensile strength of 0.455 MPa and elongation at break of 82.13%). Here, degrease cotton (DC) treated with LiOH/urea aqueous solution was used and immersed into a coagulation bath to form a film. This film was immersed in acrylic acid (AA) monomers, and in-suit polymerization was carried out in the presence of KOH and an initiator. Finally, a composite polymer membrane with sandwich structure was achieved, in which the upper and bottom layers were mainly composed of polymerized AA (PAA) while the central layer was mainly composed of DC derived film. The central layer acted as a skeleton to improve the mechanical properties and alkali resistance. The top and bottom layers (PAA-rich layers) acted as OH- ion transport carriers, making basic cations migrate along the main chain of PAA. This newly developed composite membrane showed increased tensile strength and an elongation at break of 2.7 and 1.5 times, respectively, when compared to a control PAA/KOH AEM film. Furthermore, an electrochemical stability window of 2.0 V was measured via the cyclic voltammetry curve test, showing a wide electrochemical window and promising application in Zn-Air batteries.

New insights into trace elements in the water cycle of a karst-dominated glacierized region, southeast Tibetan Plateau.

Trace elements (TEs) in water are crucial parameters for assessing water quality. However, detailed studies are limited on TEs in the hydrological system of the Tibetan plateau (TP). Here, we sampled snow, river water, and groundwater in Yulong Snow Mountain (Mt. Yulong) region, southeast TP, in 2016 and analyzed the concentrations of nine TEs (namely Al, Mn, Fe, Cr, Ni, Cu, Zn, As, and Pb). In snow, the average concentrations of Fe, Zn, and Al were >10 µg/L, whereas other elements, including Cr, Ni, Cu, As, Hg, and Pb, exhibited average concentrations <1 µg/L. The concentrations of Al, Mn, Fe, Zn, and As were higher in rivers than in snow. According to enrichment factors (EFs), Zn concentration in snow was highly influenced by anthropogenic activities, whereas Mn, Fe, Cr, and As were uninfluenced. River and lake/reservoir water near human settlements were affected by anthropogenic activities. However, groundwater around Mt. Yulong is not contaminated yet. The increasing EFs in Mt. Yulong snowpit are consistent with those of southern TP snowpits, suggesting that the area has been affected by anthropogenic activities both from local emissions and long-distance transport of pollutants from South Asia. A conceptual model was proposed to show TEs in the water cycle. Although water quality is good overall in Mt. Yulong region, threats to the water environment still exit due to increasing anthropogenic activities and climate warming. The accelerated ablation of cryosphere due to climate warming could be a source of TEs in rivers and groundwater, which should be paid attention to in the future.

Changes in hydrological behaviours triggered by earthquake disturbance in a mountainous watershed.

Landslides induced by strong earthquakes often destroy large amounts of landscape vegetation which can trigger significant changes in runoff potential and flood flow. Little is known about hydrological behaviours imposed by co-seismic landslides and their post-earthquake evolution. Therefore, we collected time-series datasets (2007-2018) of underlying surface conditions (USC) changes including landslide expansion and recovery in a watershed affected by the Wenchuan earthquake to further quantify how the large physical disturbance affected the flood hydrological behaviours. The hydrological model HEC-HMS was calibrated and validated to predict the historical hydrological behaviours based on 5 min time-series data in rainfalls and streamflow (2018-2019), showing a good model performance with a mean Nash-Sutcliffe efficiency of 0.76. It was found that, shortly after the earthquake, the sharp expansion with 11% of landslide areas elevated the magnitudes of runoff potential, peak discharge, and runoff volume by >10%, and the peak to time for the high-magnitude flood was advanced by 25 min compared to the pre-earthquake levels. The tipping point along the hydrological disturbance-recovery trajectory was detected within 2011 with higher flood peaks and volumes, and the periods of 2011-2013 (i.e. 3-5 years post-earthquake) were deemed to be a rapid recovery period, revealing an unstable hydrological function. These findings are significant for clearly understanding the magnitude and timing, as well as greater risks of post-earthquake catastrophic flooding in earthquake-stricken regions. Additionally, the post-earthquake accompanied rainstorm-induced geohazards, which limited the recovery of landscape vegetation, triggering an undulant but clear recovery process (1-7 years post-earthquake) of hydrological behaviours. These findings promoted our understanding of the spatiotemporal evolution of hydrological behaviours triggered by the earthquake, and further contribute to the development of adaptation and mitigation strategies for the unpredictable flash floods triggered by future abrupt natural hazards in earthquake-affected regions.

SIRT1 Mediates Neuropathic Pain Induced by Sciatic Nerve Chronic Constrictive Injury in the VTA-NAc Pathway.

Background: Mounting evidence has shown that sirtuin 1 (SIRT1), a class III histone deacetylase, alleviated several types of neuropathic pain in the spinal cord and dorsal root ganglion and regulated some aberrant behaviors in the ventral tegmental area (VTA) and the nucleus accumbens (NAc). Methods: In this context, the effect of SIRT1 on neuropathic pain in the VTA-NAc pathway was investigated in the model of chronic constrictive injury (CCI). Results: SIRT1 was localized in the VTA neurons in naive mice. The expression of SIRT1 was decreased in the contralateral VTA of CCI mice. After microinjection of SRT1720 (an activator of SIRT1) in the contralateral VTA of CCI mice, the established thermal hyperalgesia was attenuated. However, it was further exacerbated by EX-527 (an inhibitor of SIRT1). The elevated level of acetyl-histone 3 was reduced by SRT1720 but further elevated by EX-527 in the contralateral VTA of CCI mice. The increased expression of Fos in both VTA and NAc was downregulated by SRT1720 but further upregulated by EX-527 in CCI mice. Conclusions: The discovery of the effect of SIRT1 on neuropathic pain in the VTA represents an important step forward in understanding the analgesic mechanisms of the VTA-NAc pathway.