Non-Contact Adaptive Voltage Sensor Based on Electric Field Coupling Principle.

Non-contact voltage sensors based on the principle of electric field coupling have the advantages of simple loading and unloading, high construction safety, and the fact that they are not affected by line insulation. They can accurately measure line voltage without the need to connect to the measured object. Starting from the principle of non-contact voltage measurement, this article abstracts a non-contact voltage measurement model into the principle of capacitive voltage sharing and deduces its transfer relationship. Secondly, it is theoretically inferred that the edge effect of the traditional symmetric structure sensor plate will cause the actual capacitance value between the sensor plates to be greater than the theoretically calculated capacitance value, resulting in a certain measurement error. Therefore, the addition of an equipotential ring structure is proposed to eliminate the edge additional capacitance caused by the edge effect in order to design the sensor structure. In addition, due to the influence of sensor volume, material dielectric constant, and other factors, the capacitance value of the sensor itself is only at pF level, resulting in poor low-frequency performance and imbuing the sensor with a low voltage division ratio. In this regard, this article analyzes the measurement principle of non-contact voltage sensors. By paralleling ceramic capacitors between the two electrode plates of the sensor, the capacitance of the sensor itself is effectively increased, improving the low-frequency performance of the sensor while also increasing the sensor's voltage division ratio. In addition, by introducing a single pole double throw switch to switch parallel capacitors with different capacitance values, the sensor can have different voltage division ratios in different measurement scenarios, giving it a certain degree of adaptability. The final sensor prototype was made, and a high and low voltage experimental platform was built to test the sensor performance. The experimental results showed that the sensor has good linearity and high measurement accuracy, with a ratio error of within ±3%.

Deterministic Excitation of Polarization-Sensitive Extrinsic Anapole State in Si Nanodisk Clusters.

Nanoparticle clusters provide new degrees of freedom for light control due to their mutual interaction compared with an individual one. Here, the authors demonstrate theoretically and experimentally a type of optical anapole (a nonradiating state) termed as extrinsic anapole, with mode field spreading across Si nanodisk dimers unlike the intrinsic one that is confined within individual nanodisks. The extrinsic anapole is sensitive to the polarized excitation. When the electric vector E of excitation is perpendicular to the dimer axis, the coupled toroidal dipole (TD) mode is largely enhanced and broadened to be spectrally overlapped with the electric dipole (ED) mode. The destructive interference of these two modes results in the generation of the extrinsic anapole. However, it vanishes when E is parallel to the dimer axis. Such polarization dependence can be relieved with the participation of the third nanodisk. Scattering spectra of Si nanodisk trimers stay almost unchanged under different polarized excitations, although the near-field distributions are quite different. Finally, enhanced white-light emission is observed in Si nanodisk clusters, which can be attributed to the near-infrared absorption enhancement induced by extrinsic anapole states. The findings manifest that high-index all-dielectric nanodisk clusters are promising for light manipulation based on mode interference.

Contactless AC/DC Wide-Bandwidth Current Sensor Based on Composite Measurement Principle.

With the accelerated construction of the smart grid, new energy sources such as photovoltaic and wind power are connected to the grid. In addition to power frequency, the current signal of power grid also includes several DC signals, as well as medium-high and high-frequency transient signals. Traditional current sensors for power grids are bulky, have a narrow measurement range, and cannot measure both AC and DC at the same time. Therefore, this paper designs a non-intrusive, AC-DC wide-bandwidth current sensor based on the composite measurement principle. The proposed composite current detection scheme combines two different isolation detection technologies, namely tunneling reluctance and the Rogowski coil. These two current sensing techniques are complementary (tunneling magnetoresistive sensors have good low-frequency characteristics and Rogowski coils have good high-frequency characteristics, allowing for a wide detection bandwidth). Through theoretical and simulation analysis, the feasibility of the composite measurement scheme was verified. The prototype of composite current sensor was developed. The DC and AC transmission characteristics of the sensor prototype were measured, and the sensitivity and linearity were 11.96 mV/A, 1.14%, respectively. Finally, the sweep current method and pulse current method experiments prove that the designed composite current sensor can realize the current measurement from DC to 17 MHz.

Ag Modified SnS2 Monolayer as a Potential Sensing Material for C4F7N Decompositions: A Density Functional Theory Study.

As the field of 2D materials rapidly evolves, substances such as graphene, metal dichalcogenides, MXenes, and MBenes have garnered extensive attention from scholars in the gas sensing domain due to their unique and superior properties. Based on first-principles calculations, this work explored the adsorption characteristics of both intrinsic and silver (Ag) doped tin disulfide (SnS2) toward the decomposition components of the insulating medium C4F7N (namely, CF4, C3F6, and COF2), encompassing the adsorption energy, charge transfer, density of state (DOS), band structure, and adsorption stability. The results indicated that Ag-doped SnS2 exhibited an effective and stable adsorption for C3F6 and COF2, whereas its adsorption for CF4 was comparatively weaker. Additionally, the potential for Ag-SnS2 in detecting C3F6 was highlighted, inferred from the contributions of the band gap variations. This research provides theoretical guidance for the application of Ag-SnS2 as a sensing material in assessing the operational status of gas-insulated equipment.

Cobalt-zinc carbides embedded in N-doped porous carbon nanospheres as polysulfide mediators for efficient lithium-sulfur batteries.

Developing high-efficiency interlayer catalysts is a promising tactic for improving the cycling performance of rechargeable lithium-sulfur (Li-S) batteries. Herein, using the Prussian blue analogue as the precursor, cobalt-zinc carbide nanocrystal-embedded N-doped porous carbon (Co3ZnC@NC) is synthesized via simple post-carbonization. The obtained Co3ZnC@NC nanospheres exhibit a robust core-shell structure showing good conductivity, high porosity and available metal active sites, favoring the interfacial charge transfer and the electron transport upon electrochemical reactions. The results demonstrate that the Co3ZnC@NC catalyst is quite suitable for boosting the adsorption and redox conversion kinetics of soluble polysulfides. When acting as the separator interlayer, Co3ZnC@NC contributes to improved Li-S batteries with a high discharge specific capacity of 1659.8 mA h g-1 at 0.1C and superior cycling stability of over 250 cycles at 1.0C (high capacity retention of 84.1% after 100 cycles at 0.5C). Furthermore, the Co3ZnC@NC-based battery can maintain a high discharge capacity of 734.0 mA h g-1 at 5.0C, along with delivering a stable reversible capacity of 805.4 mA h g-1 (∼5 mA h cm-2) after 50 cycles even under a high sulfur loading of 6.2 mg cm-2. This study affords a viable way to construct highly dispersed bimetal/carbon composites for efficient catalysts and renewable energy devices.

Reduced graphene oxide-encaged submicron-silicon anode interfacially stabilized by Al2O3 nanoparticles for efficient lithium-ion batteries.

Silicon-carbon composites have been recognized as some of the most promising anode candidates for advancing new-generation lithium-ion batteries (LIBs). The development of high-efficiency silicon/graphene anodes through a simple and cost-effective preparation route is significant. Herein, by using micron silicon as raw material, we designed a mesoporous composite of silicon/alumina/reduced graphene oxide (Si/Al2O3/RGO) via a two-step ball milling combined annealing process. Commercial Al2O3 nanoparticles are introduced as an interlayer due to the toughening effect, while RGO nanosheets serve as a conductive and elastic coating to protect active submicron silicon particles during lithium alloying/dealloying reactions. Owing to the rational porous structure and dual protection strategy, the core/shell structured Si/Al2O3/RGO composite is efficient for Li+ storage and demonstrates improved electrical conductivity, accelerated charge transfer and electrolyte diffusion, and especially high structural stability upon charge/discharge cycling. As a consequence, Si/Al2O3/RGO yields a high discharge capacity of 852 mA h g-1 under a current density of 500 mA g-1 even after 200 cycles, exhibiting a high capacity retention of ∼85%. Besides, Si/Al2O3/RGO achieves excellent cycling reversibility and superb high-rate capability with a stable specific capacity of 405 mA h g-1 at 3000 mA g-1. Results demonstrate that the Al2O3 interlayer is synergistic with the indispensable RGO nanosheet shells, affording more buffer space for silicon cores to alleviate the mechanical expansion and thus stabilizing active silicon species during charge/discharge cycles. This work provides an alternative low-cost approach to achieving high-capacity silicon/carbon composites for high-performance LIBs.

A two-branch cloud detection algorithm based on the fusion of a feature enhancement module and Gaussian mixture model.

Accurate cloud detection is an important step to improve the utilization rate of remote sensing (RS). However, existing cloud detection algorithms have difficulty in identifying edge clouds and broken clouds. Therefore, based on the channel data of the Himawari-8 satellite, this work proposes a method that combines the feature enhancement module with the Gaussian mixture model (GMM). First, statistical analysis using the probability density functions (PDFs) of spectral data from clouds and underlying surface pixels was conducted, selecting cluster features suitable for daytime and nighttime. Then, in this work, the Laplacian operator is introduced to enhance the spectral features of cloud edges and broken clouds. Additionally, enhanced spectral features are input into the debugged GMM model for cloud detection. Validation against visual interpretation shows promising consistency, with the proposed algorithm outperforming other methods such as RF, KNN and GMM in accuracy metrics, demonstrating its potential for high-precision cloud detection in RS images.

Etching-free high-throughput intersectional nanofabrication of diverse optical nanoantennas for nanoscale light manipulation.

The capabilities to manipulate light-matter interaction at the nanoscale lie at the core of many promising photonic applications. Optical nanoantennas, made of metallic or dielectric materials, have seen a rapid development for their remarkable optical properties facilitating the coupling of electromagnetic waves with subwavelength entities. However, high-throughput and cost-effective fabrication of these nanoantennas is still a daunting challenge. In this work, we provide a versatile nanofabrication method capable of producing large scale optical nanoantennas with different shapes. It is developed from colloidal lithography with no dry etching required. Furthermore, both metallic and all-dielectric nanoantennas can be readily fabrication in a high-throughput fashion. Au and Si nanodisks were fabricated and employed to assemble heterostructures with monolayer tungsten disulfide. Strong coupling is observed in both systems between plasmon modes (Au nanodisks) or anapole modes (Si nanodisks) with excitons. We believe that this nanofabrication method could find a wide range of applications with the diverse optical nanoantennas it can engineer.