Fracture behavior of short fiber-reinforced CAD/CAM inlay restorations after cyclic fatigue aging.

The aim of this study was to assess the fracture behavior of molar teeth restored with MOD inlays made of experimental short fiber-reinforced CAD/CAM composite block (SFRC CAD) before and after cyclic fatigue aging. Standardized MOD cavities were prepared on 60 intact mandibular molars. Three groups of CAD/CAM made inlay restorations (Cerasmart 270, Enamic, and SFRC CAD) were fabricated (n = 20/group). All restorations were luted with self-adhesive dual-cure resin cement (G-Cem One). Half of restored teeth per each group (n = 10) were quasi-statically loaded until fracture without aging. The other half underwent cyclic fatigue aging for 500,000 cycles (Fmax = 150 N) before being loaded quasi-statically until fracture. Then, the fracture type was visually inspected. The microstructure and elemental content of CAD/CAM materials were assessed using SEM and EDS. Two-way analysis of variance (ANOVA) was used to statistically examine the data, and it was followed by the Tukey HSD test (α = 0.05). ANOVA demonstrated that both material type and aging had a significant effect (p < 0.05) on the load-bearing capacity values of the restorations. Teeth restored with SFRC CAD showed significantly the highest (p < 0.05) load-bearing capacity (2535 ± 830 N) after fatigue aging among all groups. SEM images showed the ability of short fibers in SFRC CAD composite to redirect and hinder crack propagation. With regard to fracture mode, Enamic group revealed 85% of catastrophic failure (vs. 45% and 10% for Cerasmart 270 and SFRC CAD, respectively). Large MOD cavities on molar teeth were most favorably restored with SFRC CAD inlays, yielding the highest load-bearing capacity and more restorable failures.

Interdisciplinary Delphi study by PROSEC North America: Recommendations on single indirect restorations made from ceramic and nonmetallic biomaterials for posterior teeth.

OBJECTIVE: This article puts forward consensus recommendations from PROSEC North America regarding single indirect restorations made from ceramic and nonmetallic biomaterials in posterior teeth. OVERVIEW: The consensus process involved a multidisciplinary panel and three consensus workshops. A systematic literature review was conducted across five databases to gather evidence. The recommendations, informed by findings from systematic reviews and formulated based on a two-phase e-Delphi survey, emphasize a comprehensive treatment strategy that includes noninvasive measures alongside restorative interventions for managing dental caries and tooth wear. The recommendations advocate for selecting between direct and indirect restorations on a case-by-case basis, favoring inlays and onlays over crowns to align with minimally invasive dentistry principles. The recommendations highlight the critical role of selecting restorative biomaterials based on clinical performance, esthetic properties, and adherence to manufacturer guidelines. They emphasize the importance of precision in restorative procedures, including tooth preparation, impression taking, contamination control, and luting. Regular follow-up and maintenance tailored to individual patient needs are crucial for the longevity of ceramic and nonmetallic restorations. CONCLUSIONS: These PROSEC recommendations provide a framework for dental practitioners to deliver high-quality restorative care, advocating for personalized treatment planning and minimally invasive approaches to optimize oral health outcomes. CLINICAL SIGNIFICANCE: The PROSEC North America recommendations highlight the importance of minimally invasive techniques in posterior tooth restorations using ceramic and non-metallic biomaterials. These principles prioritize tooth structure conservation and personalized treatment planning, essential for enhancing clinical outcomes and long-term oral health.

Two­year clinical performance of indirect restorations fabricated from CAD/CAM nano hybrid composite versus lithium disilicate in mutilated vital teeth. A randomized controlled trial.

TRIAL DESIGN: This is a randomized, controlled, superiority, double-blinded, parallel-group, two-arms trial with an allocation ratio of 1:1. The aim of this trial was to compare the two-year clinical performance of partial indirect restorations fabricated from CAD/CAM nano-hybrid composite and ceramic lithium disilicate blocks using the modified USPHS criteria. METHODS: In two parallel groups (n = 50 restorations), fifty participants having mutilated vital teeth with a minimum of two remaining walls were randomly enrolled in this trial and received indirect restorations of either nano-hybrid composite resin blocks (Brilliant, Coltene, Switzerland) or Lithium Disilicate (IPS Emax CAD). The restorations were assessed using modified USPHS criteria by two independent blinded assessors at baseline, six months, one-year and two years follow-up visits. Categorical and ordinal data were presented as frequencies and percentages. Categorical data were analyzed using the chi-square test. Ordinal data were analyzed using the Mann-Whitney U test for intergroup comparisons and Freidman's test followed by the Nemenyi post hoc test for intragroup comparisons. Numerical data were presented as mean and standard deviation values. They were analyzed for normality using the Shapiro-Wilk test. Data were found to be normally distributed and were analyzed using the independent t-test. The significance level was set at p ≤ 0.05 within all tests. RESULTS: Forty-eight participants received the allocated intervention and completed the follow-up periods. There was a statistically significant difference between both tested materials for all USPHS criteria regarding Marginal integrity and Marginal discoloration at six-months Follow-up, but with no statistically significant difference at one- and two-year follow-up. CONCLUSIONS: Both materials showed an acceptable, successful clinical performance along the two-years follow-up period. CLINICAL RELEVANCE: The CAD/CAM nano-hybrid composite blocks are as reliable as Lithium disilicate for restoring mutilated vital teeth.

Two-year clinical performance of indirect resin composite restorations in endodontically treated teeth with different cavity preparation designs: a randomized clinical trial.

TRIAL DESIGN: This is a randomized, controlled, superiority, double-blinded, parallel-group, two-arms trial with an allocation ratio of 1:1. This study aimed to assess whether the cavity design could affect the clinical performance of the CAD/CAM generated indirect resin composite restoration in endodontically treated teeth (ETT) evaluated using the Modified USPHS criteria after a two-year follow up. METHODS: A total of 30 participants who underwent endodontic treatment for MOD cavities in permanent molars were divided randomly into two parallel groups (n = 30 restorations) according to the performed cavity design to group 1 in which there was no cuspal reduction (inlay) and group 2 in which cuspal reduction was performed (overlay). All pulp chambers were filled with bulk fill flowable composite, and the cavities were prepared following the criteria of the cavities for indirect restorations and restored using nano-hybrid composite resin blocks (Brilliant, Coltene, Switzerland). The restorations were evaluated using the modified USPHS criteria at baseline, six months, one-year and two years follow-up visits. For qualitative data, frequencies (n) and percentages (%) were used to display the data, while mean and standard deviation (SD) were used for quantitative data. The normality of the data was evaluated using the Shapiro-Wilk and Kolmogorov-Smirnov tests. For every test, P ≤ 0.05 was used as the significance threshold. RESULTS: Twenty-six individuals completed the follow-up period after receiving the assigned intervention.The inter-group comparison showed that, at the 6- months and 12- months observation points, the overlay design had significantly better marginal adaptation, less incidence of discoloration or tooth/restoration fracture, and similar marginal integrity and caries incidence to the inlay design. After 24- months, the overlay design still had better marginal adaptation, less incidence of discoloration or tooth/restoration fracture and less caries incidence in comparison to the inlay design, while there was no difference in the marginal integrity between either design. CONCLUSIONS AND CLINICAL RELEVANCE: Cuspal reduction in endodontically treated teeth showed better clinical performance than the cusp preservation thus, the former is more reliable.

In vivo real-time temperature measurement on the surface of intact and gold-restored teeth during consumption of hot and cold drinks.

This study aimed to measure real-time temperature changes in gold-restored teeth compared with intact teeth during the intake of hot and cold drinks. Sixteen molars, including eight natural intact teeth and eight restored teeth with gold inlays, were selected from the participants. Custom-made thermocouple sensors were attached to the coronal third of the buccal surface of teeth. Participants consecutively consumed hot and cold drinks according to a standardized regimen. Resting, maximum, and minimum temperatures; time to reach peak temperatures; and heating and cooling velocities were obtained. Statistical analysis was performed using independent two-sample t-test. Teeth with gold restorations showed a significantly higher maximum temperature (44.7 °C [SD 2.9]) than did natural teeth (40.5 °C [SD 1.2]) during hot water drinking and showed a lower minimum temperature (25.0 °C [SD 4.9]) than did natural teeth (31.5 °C [SD 3.1]) during cold water drinking. The heating and cooling rates for the teeth with gold restorations were two and three times higher than those of the natural teeth. Gold-restored teeth showed greater temperature change than intact teeth in terms of magnitude and velocity in response to temperature changes induced by hot and cold drinks.

Virtual versus jaw simulation in inlay preparation preclinical teaching: a randomised controlled trial.

BACKGROUND: To investigate the effect of virtual simulation systems on the teaching of inlay experiments and to guide the experimental teaching of tooth preparation. METHODS: Participants in their second semester of the junior year were selected to carry out the unified teaching and evaluation of dental preparation theory. The age varied from 18 to 22 years (19.96 ± 0.70) and the participants were randomly divided into four groups (n = 19) with a similar male-to-female ratio following CONSORT guidelines, including a jaw simulation model training group (Group J), a virtual simulation system training group (Group V), a jaw model training first followed by a virtual system training group (Group J-V), and a virtual system followed by a jaw model training group (Group V-J). The inlay tooth preparation assessment was performed on the extracted teeth. The data were analysed according to the assessment scores by a senior clinician. The subjective feelings of the students towards the system were evaluated using questionnaires. RESULTS: The second theoretical scores of Group V-J (63.5 ± 2.89) and Group J-V (60.5 ± 3.25) were higher than those of Group V (57.5 ± 3.13) and Group J (58.0 ± 3.67). The experimental scores of Groups J-V and V-J (62.79 ± 2.84; 64.00 ± 2.85) were higher than those of Groups V and J (56.05 ± 3.39; 55.74 ± 2.53). The questionnaire survey illustrated that most students preferred the digital virtual simulation system (perfect assessment: 91.3%, accuracy: 82.6%, satisfaction: 52.2%). CONCLUSION: Virtual simulation training can facilitate the teaching effect of tooth preparation in inlay experiments, and the teaching mode of Group V-J was the best. Therefore, this teaching mode is to be popularised.

Fatigue behavior and stress distribution of molars restored with MOD inlays with and without deep margin elevation.

OBJECTIVES: This study evaluated the effect of deep margin elevation (DME) and restorative materials (leucite-reinforced glass-ceramics [C] vs. indirect resin composite [R]) on the fatigue behavior and stress distribution of maxillary molars with 2-mm deep proximal margins restored with MOD inlay. METHODS: Fifty-two extracted human third molars were randomly assigned into four groups (n = 13): C; DME + C; R; and DME + R. Inlays were fabricated in CAD-CAM and bonded to all teeth. The fatigue behavior was assessed with the stepwise stress test (10,000 cycles/step; step = 50 N; 20 Hz; initial load = 200 N). Fatigue failure loads and the number of cycles were analyzed with 2-way ANOVA and Tukey's test (p < 0.05) and Kaplan-Meier survival plots. The stress distribution was assessed with finite element analysis. The models were considered isotropic, linear, and homogeneous, and presented bonded contacts. A tripod axial load (400 N) was applied to the occlusal surface. The stress distribution was analyzed with the maximum principal stress criterion. RESULTS: For fatigue, there was no difference for DME factor (p > 0.05). For the material factor, the load and number of cycles for failure were statistically higher in the R groups (p < 0.05). The finite element analysis showed that resin composite inlays concentrated more stress in the tooth structure, while ceramic inlays concentrated more stress in the restoration. Non-reparable failures were more frequent in the resin composite inlays groups. CONCLUSIONS: DME was not negative for fatigue and biomechanical behaviors. Resin composite inlays were more resistant to the fatigue test, although the failure mode was more aggressive. CLINICAL SIGNIFICANCE: DME does not impair mechanical behavior. Resin composite inlays failed at higher loads but with a more aggressive failure mode.

Effect of different surface treatments on resin-matrix CAD/CAM ceramics bonding to dentin: in vitro study.

BACKGROUND: Evaluating the effect of different surface treatment methods on the micro-tensile bond strength (µTBS) of two different resin-matrix computer-aided design/computer-aided manufacturing (CAD/CAM) ceramics (RMCs). METHODS: A standardized inlay preparations were performed on 100 intact maxillary premolars. According to the type of the restorative material, the teeth were randomly divided into two equally sized groups (n = 50): (polymer-infiltrated ceramic (Vita Enamic) and resin-based composites (Lava Ultimate)). The inlays were fabricated using CAD/CAM technology. In each group, the specimens were randomly assigned to five subgroups (n = 10) according to the surface treatment method: group 1 used was the control group (no surface treatment); group 2, was treated with air abrasion with 50 µm Al2O3 (A) and universal adhesive (UA); group 3, was treated with air abrasion with 50 µm Al2O3 (A) and silane coupling agent (S); group 4, was treated with hydrofluoric acid (HF) and universal adhesive (UA) and group 5, was treated with Hydrofluoric acid (HF) + silane coupling agent (S). The inlays were then cemented to their respective preparations using dual-cure self-adhesive resin cement (RelyX U200, 3 M ESPE) according to the manufacturer's instructions. The µTBS test was conducted in all groups, and stereomicroscope and scanning electron microscope were used to inspect the failure mode. The data were statistically analyzed using a two-way analysis of variance (ANOVA) and Tukey's post-hoc multiple comparison tests at a significance level of p < 0.05. RESULTS: Surface treatments significantly increased the µTBS of the materials compared to the control group (p < 0.05). For CAD/CAM RBCs, the µTBS value highest in group 2 whereas, for PICN, the µTBS value was highest in group 3. Cohesive failure of CAD/CAM restorative material was the most predominant mode of failure in all treated groups, whereas adhesive failure at restoration-cement interface was the most predominant failure mode in the control group. CONCLUSION: Surface treatments increase the µTBS of resin-matrix CAD/CAM ceramics to tooth structure. Air abrasion followed by universal adhesive and hydrofluoric acid followed by silane application appears to be the best strategies for optimizing the bond strength of CAD/CAM RBCs and PICN respectively.

Wear and damage in retrieved humeral inlays of reverse total shoulder arthroplasty-where, how much, and why?

BACKGROUND: Polyethylene (PE) wear and material degradation have been reported as complications in reverse total shoulder replacements (rTSAs). In this regard, scapular notching is associated with more clinical complications. Therefore, the purposes of the study were to quantify the linear and volumetric wear, as a measure for the amount of removed material, and to qualitatively assess the PE damage modes to describe the material degradation in retrieved rTSA humeral PE inlays that contribute to failure of shoulder replacements. Furthermore, this study aimed to evaluate the effect of scapular notching on PE wear and rim damage of the humeral components. METHODS: The total study population of 39 humeral inlays contains 2 cohorts that were used for the damage mode analysis and for the wear analysis, respectively. The extent and presence of wear damage modes in 5 defined zones were assessed by a grading system for all PE joint replacements. For quantitative wear analysis the most frequent design (n = 17) was chosen. Using a coordinate-measuring machine and postprocessing software, volumetric wear measurements for the retrieved humeral PE inlays were undertaken. Furthermore, prerevision radiographs were analyzed for scapular notching. Finally, retrieval findings were correlated with clinical and radiographic data to consider the effect of notching and to identify risk of failures for these prostheses. RESULTS: Damage on the rim of the humeral PE inlays was more frequent and severe than on the intended articulation surface. Irrespective of the damage mode, the inferior rim zone sustained the greatest amount of wear damage followed by the posterior zone. Burnishing, scratching, pitting, and embedded particles are most likely to occur in the articular surface area, whereas surface deformation, abrasion, delamination and gross material degradation are predominantly present in the inferior and posterior rim zones. The retrieved inlays exhibited a mean volumetric wear rate of 296.9 mm³/yr ± 87.0 mm³/yr. However, if the notched and non-notched components were compared, a significant higher volumetric wear rate (296.5 ± 106.1 mm³/yr) was found for the notched components compared to the non-notched group (65.7 ± 7.4 mm³/yr). Generally, there was a significantly greater incidence of damage and greater amount of wear if scapular notching occurred. CONCLUSION: The notched components showed a 5-fold increase in PE wear rate. Therefore, scapular notching has a strong effect on PE damage and wear. If scapular notching can be clinically avoided, the PE wear performance is in a similar magnitude as found for hip and knee replacements.

Chairside quadrant rehabilitation: material selection in conditions with limited space.

The significantly faster fabrication technique of chairside restorations with the aid of the Cerec Primemill milling unit makes it possible to restore an entire quadrant in a reasonable amount of time. Furthermore, the procedure described in this article made it possible to use a new type of medium-strength ceramic that achieved a very good esthetic result overall.

Effect of Inlays, Onlays and Endocrown Cavity Design Preparation on Fracture Resistance and Fracture Mode of Endodontically Treated Teeth: An In Vitro Study.

PURPOSE: To evaluate the fracture resistance and failure modes of endodontically treated mandibular molars restored with different designs of inlays, onlays and endocrowns. MATERIALS AND METHODS: Extracted mandibular third molars (n = 180) were used. An access cavity was prepared on the occlusal surface of each tooth and the roots were obturated with gutta percha. All specimens were randomly divided into 6 groups (n = 30/group) according to the cavity design and the restoration material used. C: control group without access cavity preparation. IE: MOD inlay preparation with EverX Posterior (GC Europe) in the pulp chamber. IG: MOD inlay preparation with G-aenial Universal Flo (GC America) in the pulp chamber. OE: onlay preparation with EverX Posterior (GC Europe) in the pulp chamber. OG: onlay preparation with G-aenial Universal Flo (GC America) in the pulp chamber. EC: endocrown with an empty pulp chamber. All restorations were fabricated with CAD/CAM system using CERASMART® (GC Dental products Europe, Belgium) CAD/CAM blocks. Specimens were thermal-cycled and were subjected to a compressive load applied at 30° angle relative to the long axis of the tooth with a universal testing machine. Results were statistically analyzed by ANOVA followed by Tukey post hoc tests. Chi-square test and Fisher Exact tests were used for the comparisons among groups. RESULTS: The mean fracture strength was significantly different between the groups (p < 0.001); it was significantly highest for intact teeth, followed by endocrowns (p = 0.021). The strength was significantly lower for inlays (with G-aenial Universal Flo and EverX Posterior), intermediate for onlays with EverX Posterior followed by onlays with G-aenial Universal Flo. CONCLUSIONS: Endocrowns exhibited higher fracture resistance than other tested composite resin groups. Endocrowns and onlays showed a more favorable failure mode than inlay restorations.

Biology of keratorefractive surgery- PRK, PTK, LASIK, SMILE, inlays and other refractive procedures.

The outcomes of refractive surgical procedures to improve uncorrected vision in patients-including photorefractive keratectomy (PRK), laser in-situ keratomileusis (LASIK), Small Incision Lenticule Extraction (SMILE) and corneal inlay procedures-is in large part determined by the corneal wound healing response after surgery. The wound healing response varies depending on the type of surgery, the level of intended correction of refractive error, the post-operative inflammatory response, generation of opacity producing myofibroblasts and likely poorly understood genetic factors. This article details what is known about these specific wound healing responses that include apoptosis of keratocytes and myofibroblasts, mitosis of corneal fibroblasts and myofibroblast precursors, the development of myofibroblasts from keratocyte-derived corneal fibroblasts and bone marrow-derived fibrocytes, deposition of disordered extracellular matrix by corneal fibroblasts and myofibroblasts, healing of the epithelial injury, and regeneration of the epithelial basement membrane. Problems with epithelial and stromal cellular viability and function that are altered by corneal inlays are also discussed. A better understanding of the wound healing response in refractive surgical procedures is likely to lead to better treatments to improve outcomes, limit complications of keratorefractive surgical procedures, and improve the safety and efficiency of refractive surgical procedures.

Marginal quality of ceramic inlays after three different instrumental cavity preparation methods of the proximal boxes.

OBJECTIVES: The marginal quality of ceramic inlays was evaluated after the use of three different instrumental finishing methods in mesio-occluso-distal (mod) cavity boxes in vitro after hydrothermal loading (HTL). MATERIALS AND METHODS: Caries-free human molars were divided into three groups. Mod-cavities were conventionally prepared. Box finishing was performed in every group with rotating (RI), sonic (SI), or ultrasonic (USI) instruments. Surface roughness was examined. Twelve mod-cavities remained untreated. Continuous margin quality was evaluated with scanning electron microscopy (SEM). Ceramic inlays were cemented into cavities. After HTL microleakage, marginal and absolute marginal gaps were examined. All data were analyzed statistically. RESULTS: Significant differences were found, between cavity surface roughness of RI and SI groups, the RI and USI groups, but not between microleakage, marginal, absolute marginal gaps after HTL and in proximal marginal quality. No correlations between microleakage and marginal gaps nor between microleakage and surface roughness were found. CONCLUSION: Mod-cavity proximal box finishing with SI or USI resulted in a higher surface roughness than the use of RI. The type of the finishing method did not influence the marginal quality of ceramic inlays. For the mod-cavity finishing, the use of SI and USI could be an alternative instrumental method to conventional RI methods with a lower risk of iatrogenic damage of the adjacent teeth. CLINICAL RELEVANCE: This study allows the practitioner to better determine the proper indications and limitations of the sonic and ultrasonic instruments for mod-cavity proximal box finishing.

Effects of manufacturing methods on the survival rate of ceramic and indirect composite restorations: A systematic review and meta-analysis.

OBJECTIVES: To evaluate the survival rate of ceramic and indirect composite inlays, onlays, and overlays manufactured according to different methods (CAD/CAM, pressable, and stratified). MEDLINE, EMBASE, and Cochrane Library databases were searched for published articles. Risk of bias, data extraction, subgroup analysis, meta-analysis, and GRADE was performed. MATERIALS AND METHODS: Prospective, retrospective, or RCT studies, without restriction of language, from 1983 to 2019, with follow-up ≥5 years, reporting survival rates were screened independently by two reviewers in accordance with eligibility criteria. RESULTS: A total of 13 articles (12 for ceramic, one for indirect composite) met the inclusion criteria. No articles were included regarding crystalline ceramic. The estimated cumulative survival rate for CAD/CAM was 97% after 5 years and 89% after 10 years; for pressable was 95% after 5 years, and for stratified was 88% after 5 years and 93% after 10 years. CONCLUSIONS: Regardless of the manufacturing method, vitreous ceramic inlays, onlays, and overlays showed high survival, providing evidence that these restorations are a safe treatment. CLINICAL RELEVANCE: Vitreous ceramic inlays, onlays, and overlays showed high survival, regardless of the manufacturing method, providing evidence that these restorations are a safe treatment.

Two-year performance of CAD/CAM fabricated resin composite inlay restorations: A randomized controlled clinical trial.

OBJECTIVE: The aim of this study was to evaluate the 2-year clinical performance of computer-aided design/computer-aided manufacturing (CAD/CAM) resin composite inlay restorations in comparison with direct resin composite restorations. MATERIALS AND METHODS: In 44 patients, 120 class II (mesio-occlusal/disto-occlusal) cavities were randomly assigned into two groups; CAD/CAM resin composite inlay group (Lava Ultimate), direct resin composite group (Clearfil Majesty Posterior). Clinical evaluations were performed after 1 week, 6 months, 1 year, and 2 years according to the FDI criteria. The data were analyzed using Friedman's ANOVA and Mann-Whitney U tests (α = .05). RESULTS: In 41 patients, 114 restorations were evaluated at the second year (recall rate 93.2%). All restorations were ideal or clinically acceptable. At the first year, considering all criteria, there were no statistically significant differences between the groups. However, there was a significant difference in terms of surface luster at second year, in favor of inlay restorations (P = .015). The marginal staining of resin composites increased after 2 years (P = .046), but there was no significant difference between the groups. CONCLUSIONS: Except the surface luster, 2-year clinical performance of CAD/CAM resin composite inlay restorations was found similar to direct resin composite restorations according to FDI criteria CLINICAL SIGNIFICANCE: The clinical performance of CAD/CAM resin composite inlays was acceptable in class II cavities subsequent to 2-year evaluation.

[5-year follow-up of 210 Columbus knee prostheses : A prospective multicentre study]. / 5-Jahres-Follow-up von 210 Columbus-Knietotalendoprothesen : Eine prospektive multizentrische Studie.

INTRODUCTION: As part of 10-year documentation using the Columbus system, the interim evaluation was carried out 5 years after implantation with a collection of clinical scores, evaluation of radiological imaging and collection of statistics concerning complications. METHODS: There was a multicentre prospective recruitment of consecutive patients with the indication of implantation of a surface replacement prosthesis (Columbus CR, Deep Dish fixed inlay). Preoperatively, clinical scores were recorded (KSS and Oxford score). Five years postoperatively a new evaluation of clinical scores, the range of motion (ROM) and a radiological check-up including full leg imaging under load was performed. During this period, detailed complication documentation was made. RESULTS: A total of 210 patients were recruited in five centres. 187 patients were available for examination 5 years after surgery. Cumulative KSS increased from 87.5 (±26.6) preoperatively to 170 (±29.1) 5 years postoperatively. The cumulative KSS improvement was 81.5 (±35.2) points and was highly significant (p < 0.0001; t­test). The average functional improvement in the Oxford score between the preoperative and 5­year follow-up was 21.7 (±8.8) points and was also highly significant (p < 0.0001). The ROM improved from 106.3° (±20.2) preoperatively to 114.0° (±12.1) 5 years postoperatively (p < 0.0001; t test). Five years after implantation, the average mechanical leg axis was 178.0° (±2.1). There was no clinically apparent or native radiologic visible aseptic loosening of the femoral or tibial joint component. There were 33 complications, but no implant-related complications such as inlay dislocation, material fracture or aseptic loosening. In total, 6 revision surgeries were performed during the follow-up period, which corresponds to a survival rate of 97.1% (CI 95%) for the implanted Columbus knee in the present patient collective for 5 years. CONCLUSION: The interim analysis at 5 years of long-term observation of the Columbus system provided good clinical and radiographic results.

In vitro Fracture strength and hardness of different computer-aided design/computer-aided manufacturing inlays.

OBJECTIVE: The purpose of this study was to examine the fracture strength and surface microhardness of computer-aided design/computer-aided manufacturing (CAD/CAM) materials in vitro. MATERIALS AND METHODS: Mesial-occlusal-distal inlays were made from five different CAD/CAM materials (feldspathic ceramic, CEREC blocs; leucite-reinforced ceramic, IPS Empress CAD; resin nano ceramic, 3M ESPE Lava Ultimate; hybrid ceramic, VITA Enamic; and lithium disilicate ceramic, IPS e.max CAD) using CEREC 4 CAD/CAM system. Samples were adhesively cemented to metal analogs with a resin cement (3M ESPE, U200). The fracture tests were carried out with a universal testing machine. Furthermore, five samples were prepared from each CAD/CAM material for micro-Vickers hardness test. Data were analyzed with statistics software SPSS 20 (IBM Corp., New York, USA). RESULTS: Fracture strength of lithium disilicate inlays (3949 N) was found to be higher than other ceramic inlays (P < 0.05). There was no difference between other inlays statistically (P > 0.05). The highest micro-Vickers hardness was measured in lithium disilicate samples, and the lowest was in resin nano ceramic samples. CONCLUSION: Fracture strength results demonstrate that inlays can withstand the forces in the mouth. Statistical results showed that fracture strength and micro-Vickers hardness of feldspathic ceramic, leucite-reinforced ceramic, and lithium disilicate ceramic materials had a positive correlation.

Influence of proximal box elevation on bond strength of composite inlays.

OBJECTIVES: The objective of the present study was to evaluate the influence of proximal box elevation on microtensile bond strength (mTBS) of composite inlays to the proximal box floor, using either a total-etch or a self-adhesive resin cement. MATERIALS AND METHODS: Twenty-five human molars were selected, and a class II OM (inlay) cavity preparation was performed in each tooth. Cavities were randomly assigned into four experimental groups, according to the location of the proximal cervical margin (located 1 mm below cementoenamel junction (CEJ), or with proximal box elevation with composite resin) and the resin cement used for luting (a total-etch resin cement RelyX ARC or a self-adhesive resin cement G-Cem). After 1-week water storage, samples were subjected to mTBS test. Results were analyzed by Kruskal-Wallis and Mann-Whitney U tests (p < 0.05). RESULTS: Kruskal-Wallis revealed statistically significant differences among experimental groups (p = 0.007). Both resin cements showed similar bond strength values when cervical margin was located below CEJ. The proximal box elevation improved the bond strength of composite inlays for both resin cements. However, only for G-Cem was this improvement statistically significant. CONCLUSIONS: The proximal box elevation improved the bond strength attained by G-Cem resin cement. For RelyX ARC, the position of the cervical margin did not affect composite inlays bond strength. CLINICAL RELEVANCE: Proximal box elevation does not decline bond strength of composite inlays to the proximal floor when a total-etch or a self-adhesive resin cement is used.

In vitro evaluation of marginal and internal adaptation of class II CAD/CAM ceramic restorations with different resinous bases and interface treatments.

OBJECTIVES: This in vitro study evaluated the influence of different composite bases and surface treatments on marginal and internal adaptation of class II CEREC CAD/CAM ceramic inlays, before and after simulated occlusal loading. METHODS: Thirty-two IPS Empress CAD class II inlays (MO or OD) (n = 8/group) were placed on third molars, with margins 1 mm below the cementum-enamel junction (CEJ), following different cavity treatments. These treatments were non-liner (control group), a flowable composite liner (Premise flow) sandblasted or treated with soft air abrasion and a restorative composite liner (Premise) sandblasted. The restorations were then luted with Premise. All specimens were submitted to 1,000,000 cycles with a 100-N eccentric load. The tooth restoration margins were analysed semi-quantitatively by SEM pre- and post-loading. The internal adaptation was also evaluated after test completion. RESULTS: The percentage of satisfactory marginal adaptation varied from 75 to 87 % pre-loading and 62 to 72 % post-loading in occlusal enamel, from 71 to 83 % pre-loading and 52 to 63 % post-loading in proximal enamel, and from 68 to 88 % pre-loading and 43 to 66 % post-loading in cervical dentin. There were no significant differences among groups. The percentages of satisfactory tooth-composite internal adaptation varied from 81 to 98 % in occlusal dentin, from 63 to 90 % in axial dentin, and from 71 to 84 % in cervical dentin without any statistical difference. CONCLUSIONS: The results of the present study support the use of flowable or restorative composites as a liner underneath ceramic CAD/CAM inlays, producing marginal and internal adaptation which is not different from restorations placed directly on dentin. Soft air abrasion proved not to be different from sandblasting for treating cavities before cementation. CLINICAL RELEVANCE: The results of this in vitro test validate the increasing use of a flowable base/liner underneath CAD/CAM ceramic inlays to optimise tissue conservation and clinical procedures; in this case, soft air abrasion is recommended as a pre-cementation step.

Fracture Resistance of Endodontically Treated Premolars Using Nanohybrid Composite, Fiber-Reinforced Composite, Horizontal Glass Fiber Posts, and Ceramic Inlays: An In Vitro Study.

INTRODUCTION: This study evaluated the resistance to fracture of endodontically treated premolars (ETPs) with mesio-occluso-distal (MOD) cavities filled with nanohybrid composite (NHC), fiber-reinforced composite (FRC), horizontal glass fiber posts (HFP), and ceramic inlays (CI). METHODS: Eighty-four intact maxillary premolars were taken, and endodontic treatment was performed followed by MOD cavity preparations (except in the control group). They were distributed into 7 groups based on type of restoration: intact teeth (control group), ETP + MOD (not restored), NHC, FRC + NHC, HFP + NHC, FRC + HFP + NHC, and CI groups. Samples were subjected to universal testing machine until the fracture occurred and failure mode was visually inspected. RESULTS: Mean and standard deviation of fracture resistance of the 7 groups ranged from 265.6 ± 68.0 N to 1023.7 ± 76.5 N. The highest reading was noted for intact teeth followed by FRC + HFP + NHC group and then the CI group, with no significant difference among the 3 groups. The lowest reading was noted for the ETP + MOD group. Maximum unrepairable fractures were seen in the ETP + MOD and CI groups. CONCLUSION: FRC + HFP + NHC combination and CIs increased the resistance to fracture of ETPs significantly.