A multicenter study of modified electron beam output calibration.

PURPOSE: This study aims to assess the accuracy of a modified electron beam calibration based on the IAEA TRS-398 and AAPM-TG-51 in multicenter radiotherapy. METHODS: This study was performed using the Elekta and Varian Linear Accelerator electron beams with energies of 4-22 MeV under reference conditions using cylindrical (PTW 30013, IBA FC65-G, and IBA FC65-P) and parallel-plate (PTW 34045, PTW 34001, and IBA PPC-40) chambers. The modified calibration used a cylindrical chamber and an updated k ' Q $k{^{\prime}}_Q$ based on Monte Carlo calculations, whereas TRS-398 and TG-51 used cylindrical and parallel-plate chambers for reference dosimetry. The dose ratio of the modified calibration procedure, TRS-398 and TG-51 were obtained by comparing the dose at the maximum depth of the modified calibration to TRS-398 and TG-51. RESULTS: The study found that all cylindrical chambers' beam quality conversion factors determined with the modified calibration ( k ' Q ) $( {{{k^{\prime}}}_Q} )$ to the TRS-398 and TG-51 vary from 0.994 to 1.003 and 1.000 to 1.010, respectively. The dose ratio of modified/TRS-398cyl and modified/TRS-398parallel-plate, the variation ranges were 0.980-1.014 and 0.981-1.019, while for the counterpart modified/TG-51cyl was found varying between 0.991 and 1.017 and the ratio of modified/TG-51parallel-plate varied in the range of 0.981-1.019. CONCLUSION: This multi-institutional study analyzed a modified calibration procedure utilizing new data for electron beam calibrations at multiple institutions and evaluated existing calibration protocols. Based on observed variations, the current calibration protocols should be updated with detailed metrics on the stability of linac components.

Quality assessment and harmonization of laboratories across Europe for multiple SARS-CoV-2 serology assays.

BACKGROUND AND OBJECTIVES: There is a need for conversion of SARS-CoV-2 serology data from different laboratories to a harmonized international unit. We aimed to compare the performance of multiple SARS-CoV-2 antibody serology assays among 25 laboratories across 12 European countries. MATERIALS AND METHODS: To investigate this we have distributed to all participating laboratories a panel of 15 SARS-CoV-2 plasma samples and a single batch of pooled plasma calibrated to the WHO IS 20/136 standard. RESULTS: All assays showed excellent discrimination between SARS-CoV-2 seronegative plasma samples and pre-vaccinated seropositive plasma samples but differed substantially in raw antibody titres. Titres could be harmonized to binding antibody units per millilitre by calibration in relation to a reference reagent. CONCLUSION: The standardization of antibody quantification is of paramount importance to allow interpretation and comparison of serology data reported in clinical trials in order to identify donor cohorts from whom the most effective convalescent plasma can be collected.

Tissue composition and storage duration affect the usefulness of generic wet-to-dry mass conversion factors in toxicology studies.

All ecosystems are exposed to a variety of anthropogenic contaminants. The potential threat posed by these contaminants to organisms has prompted scores of toxicology studies. Contaminant concentrations in wildlife toxicology studies are inconsistently expressed in wet or dry mass units, or even on a lipid-normalized basis, but tissue composition is rarely reported, and the conversion between dry and wet mass units, notably, is often based on assumed empirical moisture contents in tissues. However, diverse factors (e.g., tissue, storage conditions) may affect tissue composition and render comparisons between studies difficult or potentially biased. Here, we used data on the concentration of mercury, a global pollutant, in tissues of red foxes (Vulpes vulpes) to quantify the effects of diverse variables on moisture and lipid contents, and their consequences on contaminant concentration in different tissues, when converting between wet and dry mass units (lipid extracted or not). We found that moisture content differed largely between organs, enough to preclude the use of a single conversion factor, and decreased by 1% per year when stored at -80 °C. Although most fox tissues had low lipid concentrations, lipid content affected water content and their extraction affected the wet to dry mass conversion factor. We thus recommend reporting tissue composition (at least water and lipid contents) systematically in toxicology studies of mercury specifically and of contaminants in general, and using tissue/species specific conversion factors to convert between dry and wet mass concentration.

Enteric methane emission estimates for the Zimbabwean Sanga cattle breeds of Tuli and Mashona.

The effectiveness of methane mitigation in ruminant livestock production systems depends on the accuracy of estimating methane emission factors and providing accurate emission inventories. Following the Paris Climate agreement, it is recommended that countries adopt the Tier-2 approach for estimating enteric methane emissions from ruminants instead of the Tier-1 approach currently used by most countries. This study sought to provide base line enteric methane emission estimates for the Tuli and Mashona Sanga cattle breeds in Zimbabwe using the IPCC Tier-2 model. Using animal characterization data collected from 412 cattle from Grasslands Research Institute and 406 cattle from Makoholi Research Institute, net energy requirements were estimated. From this and the estimate for digestibility, gross energy intake and dry matter intake were estimated. Gross energy intakes and the estimated methane conversion factor were used to estimate enteric methane emissions. Mean emission factors for Tuli were 45.1, 56, 28.5, 28.4 and 20.6 kg CH4/head/year for cows, bulls, heifers, steers and calves, respectively. For Mashona, they were 47.8, 51.9, 29, 29.1 and 20.7 kgCH4/head/year for cows, bulls, heifers, steers and calves, respectively. Generally, estimated Tier-2 emission factors were significantly different from the IPCC Tier-1 default emission factors. This study concluded that enteric methane emission factors estimated using the IPCC Tier-2 model offer insights into the controversial use of the default IPCC Tier-1 emission factors.

Comparison of the efficiency of the Onderstepoort- and Centres for Disease Control ultraviolet light traps for the collection of livestock associated Culicoides species in South Africa.

Comparative monitoring of the abundance and distribution of Culicoides biting midges (Diptera: Ceratopogonidae), the biological vectors of the causative agents of several diseases of global veterinary importance, will be crucial in determining the risk of disease outbreak and spread. Ultraviolet (UV) suction traps have become the most frequent method used for the monitoring of Culicoides diversity and abundance. The current study compared the trapping efficiency of the two most used UV suction light traps, i.e., the Onderstepoort (OP)- and the Centres for Disease Control trap, for the collection of livestock associated Culicoides species in South Africa. The study confirmed the superiority of the OP trap and indicated a correlation in species composition and age grading results as determine with the two trap types. Substantial variations in the comparative trap efficiency, as found between areas and sites within an area, suggest that a universal conversion factor between the two trap types may not be advisable as it is unclear to what extent species composition and environmental factors may influence the conversion factor. Light traps, independent of trap model, can be considered acceptable for determining the serial comparison of population numbers for seasonal fluctuation and species abundance in distribution surveys.

Challenging the association between health literacy and health: the role of conversion factors.

Previous studies have found substantial correlations between health literacy and various health outcomes. However, the role of social and personal factors in those links remains understudied. Applying a moderation approach, we assume that these factors function as conversion factors on the associations between health literacy and health outcomes. Consequently, we test if associations between health literacy and health outcomes are stronger among young male adults who score high in conversion factors compared to those who score low. Cross-sectional data from the Young Adult Survey Switzerland were used for the analyses (n = 9339, age = 18-25). Multiple logistic regression analyses were applied to estimate associations between health literacy and health. Moderator analyses with three conversion factors and five health outcomes were conducted. For each health outcome at least one conversion factor moderated the association between health literacy and health according to the hypothesis. Although strength and form of the moderation effect differ across analyses, generally stronger associations were found among groups with beneficial social or personal factors. The present findings support the hypothesis that conversion factors play a crucial role in the associations between health literacy and health. The findings, thus, point towards a potential risk of linear health literacy approaches that assume equal benefits from increased health literacy. Individuals with beneficial social and personal factors (those already privileged) may enjoy greater health benefits from interventions improving health literacy.

Expression of GM content in mass fraction from digital PCR data.

Nowadays the quantification of the content of genetically modified (GM) constituents in food or feed products is performed by using either quantitative real-time PCR (qPCR) or digital PCR (dPCR). The latter is increasingly used. Therefore, experimental protocols for the quantification of 52 GM events authorised in the EU have been converted into a digital format and minimum performance characteristics for dPCR methods are detailed. Because of the need to harmonise the transformation of PCR results between two different measurement scales, 50 conversion factors for Certified Reference Materials (CFCRM) have been experimentally determined by three and sometimes four independent expert laboratories. The uncertainty of each CFCRM has been estimated to express dPCR results in mass fraction with a consistent uncertainty contribution. In 38 out of 58 cases, the validated qPCR methods (for 52 event-specific and 6 taxon-specific measurements) could easily be transferred into dPCR methods by using the same oligo sequences, final oligo concentration or annealing temperatures for the dPCR procedure. Laboratories have nevertheless used different strategies to improve the resolution or to reduce the so-called rain in their dPCR outcome. Those modifications were needed for PCR procedures that could not be converted without changes into a digital format. Therefore, exclusion/quality criteria such as the maximum rate of partitions with intermediate fluorescence "rain", the minimum resolution and repeatability are suggested for dPCR methods. The CFCRM determined in this study were generally in agreement with the declared zygosity of the GM parental donor for hemizygous maize events. In a limited number of GM events the CFCRM values were significantly different when measured with different maize-specific (ZmAdh1 or hmgA) genes.

On the nitrogen content and a robust nitrogen-to-protein conversion factor of black soldier fly larvae (Hermetia illucens).

Currently, a broad discussion exists in the literature regarding insect protein analysis. At its core, main difficulties and uncertainties are the inconsistent use of analysis methods and nitrogen-to-protein conversion (kP) factors. While the Kjeldahl and Dumas methods are both used in the literature, their result represents inherently different nitrogen fractions. Thus far, no correlation between them is established for insect matrices, which is a major uncertainty. Although much effort has been made towards more accurate kP factors, calculation of these was based on merely one sample while the chemical composition varies depending on rearing conditions. Using a broad variation in black soldier fly (BSF) larvae samples in the present study, a correlation between Kjeldahl and Dumas and a robust kP factor have been established. Moreover, the nitrogen distribution of BSF samples was also assessed after accurate chitin analyses. A highly significant linear correlation existed between the results of Kjeldahl and Dumas (slope, 1.009; intercept, - 0.008; R2, 0.9997). Consequently, both methods were deemed interchangeable for BSF larvae. Using amino acid data, a practical, more accurate and robust kP factor of 4.43 was obtained. Concerning the chitin content, the average of all BSF larvae samples was 5.95 ± 0.86 g N-acetylglucosamine/100 g dry matter and no correlation with the kP factor was observed. Regarding the nitrogen distribution of the samples, it was found that the contribution of nitrogenous compounds other than protein and chitin is not only high but also prone to variation (12-30% of the total nitrogen content).

Modeling of the MET Sensitive Element Conversion Factor on the Intercathode Distance.

MET sensors for measuring motion parameters are used in many scientific and technical fields. Meanwhile, the geometries of the transforming cell applied practically are far from optimal, and the influence of many geometric parameters on the sensitivity has not been studied. These parameters include the intercathode distance in a four-electrode conversion cell. In this paper, a mathematical model that allows calculating the behavior of the conversion coefficient depending on the frequency for a cell with flat electrodes at different intercathode distances is constructed. The stationary current is shown to decrease monotonically with the decreasing intercathode distance at the constancy of other system parameters. At the same time, the signal current decreases in the low-frequency region and increases in the high-frequency range. Taking into account the results obtained, practically speaking, it is advisable to reduce the intercathode distance to the technologically possible minimum, which makes the frequency response more uniform and reduces the current consumed by the sensitive element.

Relationship Between Geometric and Aerodynamic Particle Size Distributions in the Formulation of Solution and Suspension Metered-Dose Inhalers.

The relationship between the geometric particle size distribution (GPSD) and the aerodynamic particle size distribution (APSD) of commercial solution and suspension metered-dose inhaler (MDI) formulations was assessed to clarify the use of GPSD to estimate the APSD. The size distribution of particles discharged from four suspension and four solution MDIs was measured using the Inas®100 light-scattering spectrometer and a Next Generation Impactor. The conversion factor was calculated by measuring the GPSD and APSD of MDIs. The morphology and physical properties of MDIs were studied using scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). Six of the eight MDIs showed similar conversion factor profiles, irrespective of their composition and formulation types. Applying the conversion factor obtained from one of the six MDIs resulted in a particle size distribution comparable to each APSD except for some formulations. The two other solution MDIs, which contained citric acid, had much higher and variable conversion factors. SEM images and DSC scans of the solids obtained by nebulization of the solutions containing beclomethasone and/or citric acid showed the formation of a paste-like amorphous solid. These results indicated that APSD of solution and suspension MDIs that form rigid particles may be estimated by using the conversion factor and GPSD. Contrarily, the estimation is more difficult in formulations that tend to lose the particle structure during the measurement.

[Evaluation of Conversion Factors for Genetically Modified Maize Quantification].

To quantify the amount of authorized GM maize or soybean, conversion factor (Cf) values are required for converting the copy number ratio of GM sequence to an endogenous sequence into weight-based GMO amounts. Cf values are available for the several latest real-time PCR instruments such as QuantStudio5, QuantStudio12K Flex, LightCycler 96, and LightCycler 480 for GM soybeans but not for GM maize. For the quantification of GM maize, we experimentally determined the Cf values targeting Cauliflower mosaic virus 35S promoter (P35S), GA21 construct specific, MIR604 event specific and MIR162 event specific sequences using the four real-time PCR instruments.

Towards metrologically traceable and comparable results in GM quantification.

The GM content in a food or feed product produced from or containing genetically modified organisms (GMO) has to be expressed in Europe in the form of a GM mass fraction. However, the most widely used quantification methods, based on PCR, are basically counting PCR-amplifiable DNA fragments in a sample extract. This paper outlines the requirements for obtaining comparable measurement results which are fit for regulatory decision-making. It introduces the concept of a reference measurement system which enables GMO analysis laboratories to relate their results to a universally accessible reference, thus establishing metrological traceability to a unique reference point. The conversion factors required for transforming data from one measurement unit into the other have to carry a minimum uncertainty and are anchored to specified certified reference materials. The establishment of such conversion factors and related calibration approaches to achieve comparable GM quantification results are sketched. Graphical abstract ᅟ.

Non-lethal sampling for stable isotope analysis of pike Esox lucius: how mucus, scale and fin tissue compare to muscle.

Stable isotope analysis (SIA) was used to examine the isotopic relationships between dorsal muscle and fin, scale and epidermal mucus in pike Esox lucius. δ13 C and δ15 N varied predictably within each tissue pairing, with conversion factors calculated for the surrogate tissues, enabling their application to the non-lethal sampling of E. lucius for SIA.

Investigations of organ and effective doses of abdominal cone-beam computed tomography during transarterial chemoembolization using Monte Carlo simulation.

BACKGROUND: To investigate the organ dose, effective dose (ED), conversion factor, and the C-arm rotation angle effects on dose variations of abdominal C-arm cone-beam computed tomography (CBCT) during transarterial chemoembolization (TACE). METHODS: The organ doses and EDs for abdominal C-arm CBCT were retrospectively calculated according to a Monte Carlo technique for 80 patients. Dose variations from projections, ED to dose-area product (DAP) ratios, and effects of body mass index (BMI) on the ED and ED to DAP ratios were also analyzed. RESULTS: The kidney received the highest dose (14.6 ± 1.2 mSv). Organ dose deviations among C-arm rotation angles was highest for stomach (CV = 0.71). The mean ED of the the CBCT run during TACE was 3.5 ± 0.5 mSv, and decreased with increased BMI (R2 = 0.45, p < 0.001). The mean ED to DAP ratio was 0.27 ± 0.04 mSv·Gy- 1·cm- 2 and tended to decrease with increased BMI (R2 = 0.55, p < 0.001). The mean ED to DAP ratios were 0.29 ± 0.02, 0.26 ± 0.02, and 0.23 ± 0.03 mSv·Gy- 1·cm- 2 for patients with BMI < 25 kg/m2, 25-30 kg/m2, and ≥30 kg/m2, respectively. CONCLUSIONS: Suitable conversion factors for C-arm CBCT facilitate the use of DAPs for estimating the ED. The patient dose can be varied by adjusting the CBCT rotation angle setting, and dose reduction strategies can be further manipulated.

Impact of roll compaction design, process parameters, and material deformation behaviour on ribbon relative density.

Ribbons from microcrystalline cellulose (MCC), mannitol, and their 50:50% mixture were produced using the roll compactors AlexanderWerk BT120, Hosokawa Alpine Pharmapaktor C250, L.B. Bohle BRC 25, and Gerteis Mini-Pactor in the frame of multilevel full factorial experimental plans. The specific compaction force (SCF)/hydraulic pressure (HP), gap width (GW), roll speed, and fraction of MCC were analyzed as quantitative factors, whereas the roll surface and sealing system were examined as qualitative factors. Ribbon relative density was investigated as response of the models. The SCF/HP is found to be the most significant factor in each model. A significant inverse effect of the GW is obtained in the models of AlexanderWerk BT120, Pharmapaktor C250, and BRC 25 roll compactors, using smooth rolls. The principle of the establishment of a conversion factor (cf) is introduced based on the obtained data sets of AlexanderWerk BT120 and Mini-Pactor. This can facilitate the transfer of a roll compaction process between different types of roll compactors.

[Measured X-ray Spectra and Absorbed Dose Conversion Factors in a Water Equivalent Phantom Irradiated with Diagnostic X-rays].

The diagnostic X-ray spectra in a water equivalent phantom have been measured. From these measured spectra, the absorbed dose conversion factors of water were derived. The primary X-ray spectra were also measured and the scattered X-ray spectra were calculated by subtraction. The measurements were made at the depths of 0, 5, 10, 15, and 20 cm in a 20 cm-thick phantom and at the X-ray tube voltages 60, 90, and 120 kV by using a small silicon diode detector. The radiation field size was 30×30 cm2 at the phantom surface. In the obtained spectra, the fraction of the scattered photon number is increased with the depth. The X-ray qualities of the spectra in the phantom were near the qualities of primary X-rays when the depth is 0 cm, and became near the qualities of scattered X-rays as the depth increases. The changes of the X-ray qualities due to the depth change were small; photon mean-energy changes were within 4.6 keV. The changes in the absorbed dose conversion factors were also small (within 0.68%). These conversion factors were 0.4-2.3% larger than those obtained from the effective energy of incident X-rays and only -0.3 to 0.5% larger than those obtained from the X-ray spectra calculated from the aluminum half value layer and the tube voltage of incident X-rays. This study shows experimentally that the absorbed dose in a water-like phantom can be calculated with good accuracy by using the absorbed dose conversion factor obtained from the incident X-rays.

Estimating Effective Dose of Radiation From Pediatric Cardiac CT Angiography Using a 64-MDCT Scanner: New Conversion Factors Relating Dose-Length Product to Effective Dose.

OBJECTIVE: The purpose of this study is to determine the conversion factors that enable accurate estimation of the effective dose (ED) used for cardiac 64-MDCT angiography performed for children. MATERIALS AND METHODS: Anthropomorphic phantoms representative of 1- and 10-year-old children, with 50 metal oxide semiconductor field-effect transistor dosimeters placed in organs, underwent scanning performed using a 64-MDCT scanner with different routine clinical cardiac scan modes and x-ray tube potentials. Organ doses were used to calculate the ED on the basis of weighting factors published in 1991 in International Commission on Radiological Protection (ICRP) publication 60 and in 2007 in ICRP publication 103. The EDs and the scanner-reported dose-length products were used to determine conversion factors for each scan mode. The effect of infant heart rate on the ED and the conversion factors was also assessed. RESULTS: The mean conversion factors calculated using the current definition of ED that appeared in ICRP publication 103 were as follows: 0.099 mSv · mGy-1 · cm-1, for the 1-year-old phantom, and 0.049 mSv · mGy-1 · cm-1, for the 10-year-old phantom. These conversion factors were a mean of 37% higher than the corresponding conversion factors calculated using the older definition of ED that appeared in ICRP publication 60. Varying the heart rate did not influence the ED or the conversion factors. CONCLUSION: Conversion factors determined using the definition of ED in ICRP publication 103 and cardiac, rather than chest, scan coverage suggest that the radiation doses that children receive from cardiac CT performed using a contemporary 64-MDCT scanner are higher than the radiation doses previously reported when older chest conversion factors were used. Additional up-to-date pediatric cardiac CT conversion factors are required for use with other contemporary CT scanners and patients of different age ranges.

Adult and offspring size in the ocean: a database of size metrics and conversion factors.

The purpose of this dataset was to compile adult and offspring size estimates for marine organisms. Adult and offspring size estimates of 408 species were compiled from the literature covering >17 orders of magnitude in body mass and including Cephalopoda (ink fish), Cnidaria ("jelly" fish), Crustaceans, Ctenophora (comb jellies), Elasmobranchii (cartilaginous fish), Mammalia (mammals), Sagittoidea (arrow worms) and Teleost (i.e., Actinopterygii, bony fish). Individual size estimates were converted to standardized size estimates (carbon weight, g) to allow for among-group comparisons. This required a number of size estimates to be converted and a compilation of conversion factors obtained from the literature are also presented.

Current knowledge on radon risk: implications for practical radiation protection? radon workshop, 1/2 December 2015, Bonn, BMUB (Bundesministerium für Umwelt, Naturschutz, Bau und Reaktorsicherheit; Federal Ministry for the Environment, Nature Conservation, Building and Nuclear Safety).

ICRP suggested a strategy based on the distinction between a protection approach for dwellings and one for workplaces in the previous recommendations on radon. Now, the Commission recommends an integrated approach for the protection against radon exposure in all buildings irrespective of their purpose and the status of their occupants. The strategy of protection in buildings, implemented through a national action plan, is based on the application of the optimisation principle below a derived reference level in concentration (maximum 300 Bq m(-3)). A problem, however, arises that due to new epidemiological findings and application of dosimetric models, ICRP 115 (Ann ICRP 40, 2010) presents nominal probability coefficients for radon exposure that are approximately by a factor of 2 larger than in the former recommendations of ICRP 65 (Ann ICRP 23, 1993). On the basis of the so-called epidemiological approach and the dosimetric approach, the doubling of risk per unit exposure is represented by a doubling of the dose coefficients, while the risk coefficient of ICRP 103 (2007) remains unchanged. Thus, an identical given radon exposure situation with the new dose coefficients would result in a doubling of dose compared with the former values. This is of serious conceptual implications. A possible solution of this problem was presented during the workshop.

Intraoperative factors affecting conversion from cruciate retaining to cruciate substituting in total knee arthroplasty.

PURPOSE: The purpose of this study was to analyse the factors affecting the conversion from posterior cruciate ligament (PCL)-retaining (CR) to PCL-substituting (PS) prostheses during total knee arthroplasty (TKA). METHODS: A total of 920 TKAs, which had been preoperatively planned to undergo implantation of CR-type prostheses, were reviewed retrospectively. Of these, 83 knees (9.0 %) were converted intraoperatively to PS prostheses. The clinical and radiological factors of the non-converted (CR) and converted (PS) groups were compared. Clinically, age, gender, body mass index, angle of flexion contracture, size of the femoral component, and thickness of the polyethylene insert were compared between the CR and PS groups. Radiologically, the severity of the varus deformity and the posterior tibial slope angle (PSA) were compared between the CR and PS groups. RESULTS: No significant differences in age, gender, body mass index, range of motion, thickness of the polyethylene insert, or severity of varus deformity were identified. The average preoperative angle of flexion contracture was 5.9° ± 7.4° in the CR group and 8.1° ± 9.1° in the PS group (p = 0.002). The average preoperative PSA was 9.6° ± 4.0° in the CR group and 11.0° ± 5.0° in the PS group (p = 0.018). The conversion rates to a PS-type femoral component of size C, D, and E were 13.1, 7.0, and 6.3 %, respectively (p = 0.004). CONCLUSION: The conversion rate from CR- to PS-type prostheses was high in patients with severe flexion contracture, steep posterior slope, and a small femoral component size. These factors should be carefully considered for appropriate selection of prosthesis type. LEVEL OF EVIDENCE: IV.