Morphological, Microstructural, and In Situ Chemical Characteristics of Siderite Produced by Iron-Reducing Bacteria.

Dissimilatory iron-reducing bacteria (DIRB) oxidize organic matter or hydrogen and reduce ferric iron to form Fe(II)-bearing minerals, such as magnetite and siderite. However, compared with magnetite, which was extensively studied, the mineralization process and mechanisms of siderite remain unclear. Here, with the combination of advanced electron microscopy and synchrotron-based scanning transmission X-ray microscopy (STXM) approaches, we studied in detail the morphological, structural, and chemical features of biogenic siderite via a growth experiment with Shewanella oneidensis MR-4. Results showed that along with the growth of cells, Fe(II) ions were increasingly released into solution and reacted with CO32- to form micrometer-sized siderite minerals with spindle, rod, peanut, dumbbell, and sphere shapes. They are composed of many single-crystal siderite plates that are fanned out from the center of the particles. Additionally, STXM revealed Fh and organic molecules inside siderite. This suggests that the siderite crystals might assemble around a Fh-organic molecule core and then continue to grow radially. This study illustrates the biomineralization and assembly of siderite by a successive multistep growth process induced by DIRB, also provides evidences that the distinctive shapes and the presence of organic molecules inside might be morphological and chemical features for biogenic siderite.

Bimetallic Cu-Rh Nanoparticles on Diazonium-Modified Carbon Powders for the Electrocatalytic Reduction of Nitrates.

4-Benzenethiol-functionalized high-surface-area graphite powder was prepared and decorated with bimetallic Cu100-xRhx nanoparticles (NPs) to serve as electrocatalysts for the reduction of nitrates. In the first step, the HSAG powder was grafted with in-situ-generated diazonium compounds from 4-aminothiophenol (ATP) in an acidic medium using NaNO2 for the diazotization process. The surface composition was tuned using different initial quantities of ATP. The surface XPS-determined S/C atomic ratio was found to increase stepwise with the initial quantity of amine. In a second step, the grafted and untreated HSAG powders were decorated with Cu100-xRhx NPs by a wet chemical method and the elemental composition of the end composites was assessed by EDS-SEM and ICP, whereas TEM and EDS-TEM served to characterize the NP morphology and their composition on the nanometer scale. In all cases, the NP size was invariably found to be ∼1.7 nm but with a size distribution becoming narrower under an increasing grafting rate and the global composition enriched in copper. Voltammetry was performed with a cavity microelectrode to evaluate the electrocatalytic performance of the composites for nitrate reduction. Increasing diazonium grafting led to a progressive reduction of the peak current intensity and a shift of the peak potentials toward cathodic values. The maximum intensity was obtained for 0.005 µmol of diazonium salt per mg of HSAG, with a gain of 40% in comparison to the best untreated sample. This improvement and a change in the voltammogram characteristics after grafting seem to result from modifications of the local composition at the level of NPs that differ from the global composition. This work conclusively shows that diazonium surface modification is important not only in attaching electrocatalytic NPs to carbon supports but also in providing a narrower size distribution of the electrocatalysts together with finely tuned catalytic properties.

First Evidence of Rh Nano-Hydride Formation at Low Pressure.

Rh-based nanoparticles supported on a porous carbon host were prepared with tunable average sizes ranging from 1.3 to 3.0 nm. Depending on the vacuum or hydrogen environment during thermal treatment, either Rh metal or hydride is formed at nanoscale, respectively. In contrast to bulk Rh that can form a hydride phase under 4 GPa pressure, the metallic Rh nanoparticles (∼2.3 nm) absorb hydrogen and form a hydride phase at pressure below 0.1 MPa, as evidenced by the presence of a plateau pressure in the pressure-composition isotherm curves at room temperature. Larger metal nanoparticles (∼3.0 nm) form only a solid solution with hydrogen under similar conditions. This suggests a nanoscale effect that drastically changes the Rh-H thermodynamics. The nanosized Rh hydride phase is stable at room temperature and only desorbs hydrogen above 175 °C. Within the present hydride particle size range (1.3-2.3 nm), the hydrogen desorption is size-dependent, as proven by different thermal analysis techniques.

Nanoscale investigation by TEM and STEM-EELS of the laser induced yellowing.

Nd-YAG QS laser cleaning of soiled stone at 1064 nm can sometimes result in a more yellow appearance compared to other cleaning techniques. Especially in France, this yellowing effect is still considered as a major aesthetic issue by the architects and conservators. One explanation states that the yellowing is linked to the formation of iron-rich nanophase(s) through the laser beam interaction with black crusts that would re-deposit on the cleaned substrate after irradiation. To characterize these nanophases, a model crust containing hematite was elaborated and laser irradiated using a Nd-YAG QS laser. The color of the sample shifted instantaneously from red to a bright yellow and numerous particles were ablated in a visible smoke. Transmission electron microscopy (TEM) was used to examine the morphology and the crystallinity of the neo-formed compounds, both on the surface of the samples and in the ablated materials. In addition, an investigation of the chemical and structural properties of the nanophases was conducted by X-ray dispersive energy (EDX) and electron energy loss (EELS) spectroscopies. It was found that both the surface of the sample and the ablated materials are covered by crystallized nano-spheres and nano-residues, all containing iron and oxygen, sometimes along with calcium and sulfur. In particular an interfacial area containing the four elements was evidenced between some nanostructures and the substrate. Magnetite Fe3O4 was also identified at the nanoscale. This study demonstrates that the laser yellowing of a model crust is linked to the presence of iron-rich nanophases including CaxFeySzOδ nanostructures and magnetite Fe3O4 at the surface after irradiation.

Investigation of the local structure of nanosized rhodium hydride.

The local structure and the thermal stability of small and well-dispersed RhHx nanoparticles (average size of 1.4 nm) were studied by in situ X-ray Absorption Spectroscopy. The RhHx nanoparticles are stable at room temperature and undergo a structural transition from hydride (fcc) to metal phase (fcc) with a shrinking of the lattice volume due to the desorption of hydrogen. This phase transition occurs in the temperature range of 150-180 °C, in good agreement with the results from thermo-desorption spectroscopy. Above 180 °C, the desorbed nanoparticles undertake important coalescence. In situ transmission electron microscopy performed up to 300 °C proves that this process cannot be only thermal, thus it may be ascribed to a X-ray beam effect.