First detection of porcine circovirus type 2e in Europe.

Porcine circovirus 2 (PCV-2) infections are among the most economically important in swine farming. Because of the high evolutionary rate of PCV-2, several variants have emerged and are currently classified into several genotypes. However, only three (i.e. PCV-2a, PCV-2b, and PCV-2d) have a worldwide distribution, with other genotypes restricted to certain geographical regions and/or for limited time periods. Underdiagnosis or underreporting of these genotypes cannot be excluded. This is the first report of the detection and genetic characterisation of the PCV-2e genotype in Europe, from sows on a farm in Italy showing no clinical evidence of porcine circovirus disease. A follow-up study demonstrated persistent subclinical evidence of PCV-2e on the farm, at low frequency and viral load. This incidental finding emphasises the need for more intensive routine monitoring activities involving asymptomatic animals, coupled with DNA sequencing and data sharing. Considering the relevant genetic and phenotypic divergence of such genotypes, the actual efficacy of currently applied vaccines and diagnostic assays should be further evaluated.

Photochemistry of methoxyhydroquinone and methoxy-p-benzoquinone in solution related to the photoyellowing of the lignocellulosics.

The photoreactivity of methoxy-p-benzoquinone (MQ) and methoxyhydroquinone (MHQ) in dilute solution (10(-4)-10(-3) M) was studied using continuous irradiation and laser flash photolysis (LFP). The quinone irradiated in degassed tetrahydrofuran (THF) gives MHQ and an adduct with the solvent. Only the formation of hydroquinone is observed in ethanol, and hydroxylation is evidenced in water, whereas the compound is stable in CCl4. The bis-quinone, 4,4'-dimethoxybiphenyl-2,5,2',5'-bisquinone, and the dibenzofurane-quinone, 8-hydroxy-3,7-dimethoxydibenzofuran-1,4-quinone, are formed in the presence of MHQ, whereas the reactivity is low with ethylconiferyl alcohol. When MHQ is irradiated selectively in degassed THF, the formation of MQ and of the bis-hydroquinone, 4,4'-dimethoxy-2,5,2',5'-tetrahydroxy-biphenyl, are observed. The dimer is oxidized photochemically or thermally into the mono- or bis-quinones, the process being accelerated in alkaline medium. The formation of the dimers is strongly favored by the contiguous presence of quinone and hydroquinone. When MHQ is selectively irradiated in the presence of transethylconiferaldehyde (EtC), quinone formation and isomerization of EtC are observed. LFP experiments, performed with a selective excitation of MQ, indicate that the triplet state of the quinone is strongly quenched by MHQ to conduce to a semiquinone radical. The interaction between 3MQ* and MQ is mainly driven by an electron transfer process according to the similar value of the quenching rate constant found with another electron donor compound such as 1,4-dimethoxybenzene. By contrast, no strong quenching of 3EtC* by MHQ was observed. It is proposed that the photochemistry of the couple MQ/MHQ is governed by the formation of encounter complex between either 3MQ* and MHQ or 3MHQ* and MQ. Consequently, the fast part of the photoyellowing of lignocellulosics does not appear to involve the couple MHQ/MQ or MHQ/etherified coniferaldehyde, but more likely a combination of oxidation of the hydroquinone by ground-state oxygen and photohydration of the formed quinone from its triplet state, giving inter-alia more colored o-quinonoid type molecules.

Photocatalytic degradation of lignin and lignin models, using titanium dioxide: the role of the hydroxyl radical.

The role of hydroxyl radicals on the degradation of lignins during a cellulosic pulp bleaching process including a photocatalytic stage, was assessed using peroxyformic acid lignins EL1 and REL1 and two phenolic niphenyl lignin models 1 and 2. The irradiations were performed in the absence of photocatalyst TiO2 and H2O2 (condition a), in the presence of TiO2 (condition b) and in the presence of H2O2 (condition c). The experiments were conducted in alkaline (pH approximately 11) aqueous ethanol solutions with oxygen bubbling. The relative phenolic content of the irradiated solutions, which is indicative of the involvement of hydroxyl radicals, was determined by ionization absorption spectroscopy. The results obtained show that the catalyzed reaction involves both degradation of the phenolate groups by electron transfer and hydroxylation of the lignin aromatic structure. Benzyl alcohol structural elements in sodium borohydride reduced lignin REL1 and compound 2 were also found as good trapping agents for the hydroxyl radicals. The degradation of EL1 was studied by measuring its fluorescence emission by comparison to the fluorescence of compound 2. The emission spectra indicate that some biphenyl phenolate anions in EL1 are reacting under UV/visible irradiation and some others, probably polyphenolic chromophores emitting less fluorescence, are formed.

Thermoset phenolic matrices reinforced with unmodified and surface-grafted furfuryl alcohol sugar cane bagasse and curaua fibers: properties of fibers and composites.

Composites based on phenolic matrices and unmodified and chemically modified sugar cane bagasse and curaua fibers were prepared. The fibers were oxidized by chlorine dioxide, mainly phenolic syringyl and guaiacyl units of the lignin polymer, followed by grafting furfuryl alcohol (FA), which is a chemical obtained from a renewable source. The fibers were widely characterized by chemical composition analysis, crystallinity, UV-vis diffuse reflectance spectroscopy, SEM, DSC, TG, tensile strength, and 13C CP-MAS NMR. The composites were analyzed by SEM, impact strength, and DMA. The SEM images and DMA results showed that the oxidation of sugar cane bagasse fibers followed by reaction with FA favored the fiber/matrix interaction at the interface. The same chemical modification was less effective for curaua fibers, probably due to its lower lignin content, since the reaction considered touches mainly the lignin moiety. The tensile strength results obtained showed that the fibers were partially degraded by the chemical treatment, decreasing then the impact strength of the composites reinforced with them. In the continuity of the present project, efforts has been addressed to the optimization of fiber surface modification, looking for reagents preferably obtained from renewable resources and for chemical modifications that intensify the fiber/matrix interaction without loss of mechanical properties.