Multi-Electrode Array with a Planar Surface for Cell Patterning by Microprinting.

Multielectrode arrays (MEAs) are devices for non-invasive electrophysiological measurements of cell populations. This paper describes a novel fabrication method of MEAs with a fully planar surface. The surface of the insulation layer and the surface of the electrodes were on one plane; we named this device the planar MEA (pMEA). The main advantage of the pMEA is that it allows uniform contact between the pMEA surface and a substrate for positioning of microfluidic channels or microprinting of a cell adhesive layer. The fabrication of the pMEA is based on a low adhesive Au sacrificial peel-off layer. In divergence from conventional MEAs with recessed electrodes, the electrodes of the pMEA lead across the sloped edge of the insulation layer. To make this, the profile of the edge of the insulation layer was measured and the impedance of the planar electrodes was characterized. The impedance of the pMEA was comparable with the impedance of conventional MEA electrodes. The pMEA was tested for patterning HL-1 cells with a combination of imprinting fibronectin and coating by antifouling poly (l-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG). The HL-1 cells remained patterned even at full confluency and presented spontaneous and synchronous beating activity.

DNA interaction with platinum-based cytostatics revealed by DNA sequencing.

The main mechanism of action of platinum-based cytostatic drugs - cisplatin, oxaliplatin and carboplatin - is the formation of DNA cross-links, which restricts the transcription due to the disability of DNA to enter the active site of the polymerase. The polymerase chain reaction (PCR) was employed as a simplified model of the amplification process in the cell nucleus. PCR with fluorescently labelled dideoxynucleotides commonly employed for DNA sequencing was used to monitor the effect of platinum-based cytostatics on DNA in terms of decrease in labeling efficiency dependent on a presence of the DNA-drug cross-link. It was found that significantly different amounts of the drugs - cisplatin (0.21 µg/mL), oxaliplatin (5.23 µg/mL), and carboplatin (71.11 µg/mL) - were required to cause the same quenching effect (50%) on the fluorescent labelling of 50 µg/mL of DNA. Moreover, it was found that even though the amounts of the drugs was applied to the reaction mixture differing by several orders of magnitude, the amount of incorporated platinum, quantified by inductively coupled plasma mass spectrometry, was in all cases at the level of tenths of µg per 5 µg of DNA.

Nanostructured Polypyrrole-Based Ammonia and Volatile Organic Compound Sensors.

The aim of this review is to summarize the recent progress in the fabrication of efficient nanostructured polymer-based sensors with special focus on polypyrrole. The correlation between physico-chemical parameters, mainly morphology of various polypyrrole nanostructures, and their sensitivity towards selected gas and volatile organic compounds (VOC) is provided. The different approaches of polypyrrole modification with other functional materials are also discussed. With respect to possible sensors application in medicine, namely in the diagnosis of diseases via the detection of volatile biomarkers from human breath, the sensor interaction with humidity is described as well. The major attention is paid to analytes such as ammonia and various alcohols.

Iterative Precise Conductivity Measurement with IDEs.

The paper presents a new approach in the field of precise electrolytic conductivity measurements with planar thin- and thick-film electrodes. This novel measuring method was developed for measurement with comb-like electrodes called interdigitated electrodes (IDEs). Correction characteristics over a wide range of specific conductivities were determined from an interface impedance characterization of the thick-film IDEs. The local maximum of the capacitive part of the interface impedance is used for corrections to get linear responses. The measuring frequency was determined at a wide range of measured conductivity. An iteration mode of measurements was suggested to precisely measure the conductivity at the right frequency in order to achieve a highly accurate response. The method takes precise conductivity measurements in concentration ranges from 10(-6) to 1 M without electrode cell replacement.

Chemical sensor platform for non-invasive monitoring of activity and dehydration.

A non-invasive solution for monitoring of the activity and dehydration of organisms is proposed in the work. For this purpose, a wireless standalone chemical sensor platform using two separate measurement techniques has been developed. The first approach for activity monitoring is based on humidity measurement. Our solution uses new humidity sensor based on a nanostructured TiO2 surface for sweat rate monitoring. The second technique is based on monitoring of potassium concentration in urine. High level of potassium concentration denotes clear occurrence of dehydration. Furthermore, a Wireless Body Area Network (WBAN) was developed for this sensor platform to manage data transfer among devices and the internet. The WBAN coordinator controls the sensor devices and collects and stores the measured data. The collected data is particular to individuals and can be shared with physicians, emergency systems or athletes' coaches. Long-time monitoring of activity and potassium concentration in urine can help maintain the appropriate water intake of elderly people or athletes and to send warning signals in the case of near dehydration. The created sensor system was calibrated and tested in laboratory and real conditions as well. The measurement results are discussed.

Sensing properties of multiwalled carbon nanotubes grown in MW plasma torch: electronic and electrochemical behavior, gas sensing, field emission, IR absorption.

Vertically aligned multi-walled carbon nanotubes (VA-MWCNTs) with an average diameter below 80 nm and a thickness of the uniform VA-MWCNT layer of about 16 µm were grown in microwave plasma torch and tested for selected functional properties. IR absorption important for a construction of bolometers was studied by Fourier transform infrared spectroscopy. Basic electrochemical characterization was performed by cyclic voltammetry. Comparing the obtained results with the standard or MWCNT­modified screen-printed electrodes, the prepared VA-MWCNT electrodes indicated their high potential for the construction of electrochemical sensors. Resistive CNT gas sensor revealed a good sensitivity to ammonia taking into account room temperature operation. Field emission detected from CNTs was suitable for the pressure sensing application based on the measurement of emission current in the diode structure with bending diaphragm. The advantages of microwave plasma torch growth of CNTs, i.e., fast processing and versatility of the process, can be therefore fully exploited for the integration of surface-bound grown CNTs into various sensing structures.

Liposomal nanotransporter for targeted binding based on nucleic acid anchor system.

Microfluidic techniques have been developed intensively in recent years due to lower reagent consumption, faster analysis, and possibility of the integration of several analytical detectors into one chip. Electrochemical detectors are preferred in microfluidic systems, whereas liposomes can be used for amplification of the electrochemical signals. The aim of this study was to design a nanodevice for targeted anchoring of liposome as transport device. In this study, liposome with encapsulated Zn(II) was prepared. Further, gold nanoparticles were anchored onto the liposome surface allowing binding of thiol moiety-modified molecules (DNA). For targeted capturing of the transport device, DNA loops were used. DNA loops were represented by paramagnetic microparticles with oligo(DT)25 chain, on which a connecting DNA was bound. Capturing of transport device was subsequently done by hybridization to the loop. The individual steps were analyzed by electrochemistry and UV/Vis spectrometry. For detection of Zn(II) encapsulated in liposome, a microfluidic system was used. The study succeeded in demonstrating that liposome is suitable for the transport of Zn(II) and nucleic acids. Such transporter may be used for targeted binding using DNA anchor system.

Glutathione modified CdTe quantum dots as a label for studying DNA interactions with platinum based cytostatics.

Cisplatin, carboplatin, and oxaliplatin represent three generations of platinum based drugs applied successfully for cancer treatment. As a consequence of the employment of platinum based cytostatics in the cancer treatment, it became necessary to study the mechanism of their action. Current accepted opinion is the formation of Pt-DNA adducts, but the mechanism of their formation is still unclear. Nanomaterials, as a progressively developing branch, can offer a tool for studying the interactions of these drugs with DNA. In this study, fluorescent CdTe quantum dots (QDs, λem = 525 nm) were employed to investigate the interactions of platinum cytostatics (cisplatin, carboplatin, and oxaliplatin) with DNA fragment (500 bp, c = 25 µg/mL). Primarily, the fluorescent behavior of QDs in the presence of platinum cytostatics was monitored and major differences in the interaction of QDs with tested drugs were observed. It was found that the presence of carboplatin (c = 0.25 mg/mL) had no significant influence on QDs fluorescence; however cisplatin and oxaliplatin quenched the fluorescence significantly (average decrease of 20%) at the same concentration. Subsequently, the amount of platinum incorporated in DNA was determined by QDs fluorescence quenching. Best results were reached using oxaliplatin (9.4% quenching). Linear trend (R(2) = 0.9811) was observed for DNA platinated by three different concentrations of oxaliplatin (0.250, 0.125, and 0.063 mg/mL). Correlation with differential pulse voltammetric measurements provided linear trend (R(2) = 0.9511). As a conclusion, especially in the case of oxaliplatin-DNA adducts, the quenching was the most significant compared to cisplatin and nonquenching carboplatin.

Integrated chip electrophoresis and magnetic particle isolation used for detection of hepatitis B virus oligonucleotides.

Rapid and sensitive detection is a key step in the effective and early response to the global hazard of various viral diseases. In this study, an integrated isolation of hepatitis B virus (HBV)-specific DNA fragment by magnetic nanoparticles (MNPs) and its immediate analysis by microchip CGE was performed. Microfluidic CE chip was used to accommodate the complete process of viral DNA isolation by MNPs including hybridization and thermal denaturation followed by CE separation. Beforehand, calibration curves of HBV fragments were constructed. For isolation by MNPs, specific streptavidin-biotin interaction was used to bind complementary HBV fragment to magnetic particles. After analysis of isolated HBV by regular MNPs method, innovative approach was performed. The commercial CE chip (Bio-rad) was successfully used to execute HBV fragment isolation. Detection using LIF with detection limit of 1 ng/mL was accomplished.

Behaviour of zinc complexes and zinc sulphide nanoparticles revealed by using screen printed electrodes and spectrometry.

In this study, we focused on microfluidic electrochemical analysis of zinc complexes (Zn(phen)(his)Cl2, Zn(his)Cl2) and ZnS quantum dots (QDs) using printed electrodes. This method was chosen due to the simple (easy to use) instrumentation and variable setting of flows. Reduction signals of zinc under the strictly defined and controlled conditions (pH, temperature, flow rate, accumulation time and applied potential) were studied. We showed that the increasing concentration of the complexes (Zn(phen)(his)Cl2, Zn(his)Cl2) led to a decrease in the electrochemical signal and a significant shift of the potential to more positive values. The most likely explanation of this result is that zinc is strongly bound in the complex and its distribution on the electrode is very limited. Changing the pH from 3.5 to 5.5 resulted in a significant intensification of the Zn(II) reduction signal. The complexes were also characterized by UV/VIS spectrophotometry, chromatography, and ESI-QTOF mass spectrometry.

Voltammetry as a tool for characterization of CdTe quantum dots.

Electrochemical detection of quantum dots (QDs) has already been used in numerous applications. However, QDs have not been well characterized using voltammetry, with respect to their characterization and quantification. Therefore, the main aim was to characterize CdTe QDs using cyclic and differential pulse voltammetry. The obtained peaks were identified and the detection limit (3 S/N) was estimated down to 100 fg/mL. Based on the convincing results, a new method for how to study stability and quantify the dots was suggested. Thus, the approach was further utilized for the testing of QDs stability.

Paramagnetic particles coupled with an automated flow injection analysis as a tool for influenza viral protein detection.

Currently, the influenza virus infects millions of individuals every year. Since the influenza virus represents one of the greatest threats, it is necessary to develop a diagnostic technique that can quickly, inexpensively, and accurately detect the virus to effectively treat and control seasonal and pandemic strains. This study presents an alternative to current detection methods. The flow-injection analysis-based biosensor, which can rapidly and economically analyze a wide panel of influenza virus strains by using paramagnetic particles modified with glycan, can selectively bind to specific viral A/H5N1/Vietnam/1203/2004 protein-labeled quantum dots. Optimized detection of cadmium sulfide quantum dots (CdS QDs)-protein complexes connected to paramagnetic microbeads was performed using differential pulse voltammetry on the surface of a hanging mercury drop electrode (HMDE) and/or glassy carbon electrode (GCE). Detection limit (3 S/N) estimations based on cadmium(II) ions quantification were 0.1 µg/mL or 10 µg/mL viral protein at HMDE or GCE, respectively. Viral protein detection was directly determined using differential pulse voltammetry Brdicka reaction. The limit detection (3 S/N) of viral protein was estimated as 0.1 µg/mL. Streptavidin-modified paramagnetic particles were mixed with biotinylated selective glycan to modify their surfaces. Under optimized conditions (250 µg/mL of glycan, 30-min long interaction with viral protein, 25°C and 400 rpm), the viral protein labeled with quantum dots was selectively isolated and its cadmium(II) content was determined. Cadmium was present in detectable amounts of 10 ng per mg of protein. Using this method, submicrogram concentrations of viral proteins can be identified.

Modern micro and nanoparticle-based imaging techniques.

The requirements for early diagnostics as well as effective treatment of insidious diseases such as cancer constantly increase the pressure on development of efficient and reliable methods for targeted drug/gene delivery as well as imaging of the treatment success/failure. One of the most recent approaches covering both the drug delivery as well as the imaging aspects is benefitting from the unique properties of nanomaterials. Therefore a new field called nanomedicine is attracting continuously growing attention. Nanoparticles, including fluorescent semiconductor nanocrystals (quantum dots) and magnetic nanoparticles, have proven their excellent properties for in vivo imaging techniques in a number of modalities such as magnetic resonance and fluorescence imaging, respectively. In this article, we review the main properties and applications of nanoparticles in various in vitro imaging techniques, including microscopy and/or laser breakdown spectroscopy and in vivo methods such as magnetic resonance imaging and/or fluorescence-based imaging. Moreover the advantages of the drug delivery performed by nanocarriers such as iron oxides, gold, biodegradable polymers, dendrimers, lipid based carriers such as liposomes or micelles are also highlighted.

Chip gel electrophoresis as a tool for study of matrix metalloproteinase 9 interaction with metallothionein.

Matrix metalloproteinases (MMPs) play numerous roles in physiological and pathological processes including cancer. Interactions of MMPs with other zinc-binding proteins are of great interest mainly from the point of view of the participation of these proteins in carcinogenesis. The aim of this study was to utilize chip gel electrophoresis for investigation of matrix metalloproteinase 9 (gelatinase B, MMP-9) interactions with collagen. The interaction was observed and the effect of temperature was tested. We further focused on the study of activation of MMP-9 by the presence of zinc-binding proteins called metallothioneins (MT). We confirmed the basic presumption of the activation of MMP-9 by the presence of MT similar to the temperature effect. Moreover, we chose the method of differential pulse voltammetry Brdicka reaction to verify our results. It can be concluded that the activity of MMP-9 was higher in the presence of MT in comparison with the experimental collagen(type I)-MMP-9 mixture in vitro.

Biotin-modified glutathione as a functionalized coating for bioconjugation of CdTe-based quantum dots.

In this study, biotin-conjugated glutathione was synthesized using peptide bonding of the biotin carboxy group and amino group of the γ-glutamic acid to prepare an alternative coating for CdTe quantum dots (QDs). This type of coating combines the functionality of the biotin with the fluorescent properties of the QDs to create a specific, high-affinity fluorescent probe able to react with avidin, streptavidin and/or neutravidin. Biotin-functionalized glutathione-coated CdTe QDs were prepared by a simple one-step method using Na2 TeO3 and CdCl2. Obtained QDs were separated from the excess of the biotin-conjugated glutathione by CE employing 300 mM borate buffer with pH 7.8 as a background electrolyte. The detection of sample components was performed by the photometric detection at 214 nm and LIF employing Ar⁺ ion laser (488 nm).

Electrophoretic fingerprint metallothionein analysis as a potential prostate cancer biomarker.

Prostate-specific antigen (PSA) is a routinely used marker of prostate cancer; however, the cut-off values for unambiguous positive/negative prostate cancer diagnoses are not defined. Therefore, despite the best effort, certain percentage of misdiagnosed cases is being recorded every year. For this reason, search for more specific diagnostic markers is of great interest. In this study, systematic comparison of PSA and metallothionein (MT) levels in blood serum of 46 prostate cancer-diagnosed patients is presented. It is clearly demonstrated that PSA levels vary significantly and despite normal total PSA values in the range of 0 - 4 ng/mL were obtained in over 36.9% of cases, positive prostate cancer was diagnosed by biopsy. In contrary, MT levels were considerably elevated in all tested samples and no significant variations were observed. These results are indicating the potential of MT as an additional prostate cancer marker reducing, in combination with PSA, the probability of false positive/negative diagnosis. To increase the throughput of the screening, chip-based capillary electrophoresis was suggested as a rapid and effective method for the fingerprinting analysis of prostate cancer from diseased blood sera.

Microfluidic tool based on the antibody-modified paramagnetic particles for detection of 8-hydroxy-2'-deoxyguanosine in urine of prostate cancer patients.

Guanosine derivatives are important for diagnosis of oxidative DNA damage including 8-hydroxy-2'-deoxyguanosine (8-OHdG) as one of the most abundant products of DNA oxidation. This compound is commonly determined in urine, which makes 8-OHdG a good non-invasive marker of oxidation stress. In this study, we optimized and tested the isolation of 8-OHdG from biological matrix by using paramagnetic particles with an antibody-modified surface. 8-OHdG was determined using 1-naphthol generated by alkaline phosphatase conjugated with the secondary antibody. 1-Naphthol was determined by stopped flow injection analysis (SFIA) with electrochemical detector using a glassy carbon working electrode and by stationary electrochemical detection using linear sweep voltammetry. A special modular electrochemical SFIA system which needs only 10 µL of sample including working buffer for one analysis was completely designed and successfully verified. The recoveries in different matrices and analyte concentration were estimated. Detection limit (3 S/N) was estimated as 5 pg/mL of 8-OHdG. This method promises to be very easily modified to microfluidic systems as "lab on valve". The optimized method had sufficient selectivity and thus could be used for determination of 8-OHDG in human urine and therefore for estimation of oxidative DNA damage as a result of oxidation stress in prostate cancer patients.

Paramagnetic antibody-modified microparticles coupled with voltammetry as a tool for isolation and detection of metallothionen as a bioindicator of metal pollution.

Low-molecular mass proteins rich in cysteines called metallothioneins (MT) can be considered as markers for the pollution of the environment by metals. Here, we report on suggestion for an automated procedure for the isolation of MT followed by voltammetric analysis. Primarily, we optimized the automated detection of MT using an electrochemical analyser. It was found that the most sensitive and repeatable analyses are obtained at a temperature of 4 °C for the supporting electrolyte. Further, we optimized experimental conditions for the isolation of MT by using antibody-linked paramagnetic microparticles. Under the optimal conditions (4 h long interaction between the microparticles and MT), the microparticles were tested on isolation of various amounts of MT. The lowest isolated amount of MT by antibody-linked paramagnetic microparticles was 5 µg ml(-1) of MT (50 ng). The automated procedure of MT isolation was further tested on isolation of MT from guppy fish (Poecilia reticulata) treated with silver(i) ions (50 µM AgNO(3)). The whole process lasted less than five hours and was fully automated. We attempted to correlate these results with the standard method for MT isolation. The correlation coefficient is 0.9901, which confirms that results are in good agreement. Moreover, the concentration of silver ions in tissues of fish treated with Ag(i) ions was determined by high performance liquid chromatography with electrochemical detection.

Bio-sensing of cadmium(II) ions using Staphylococcus aureus.

Cadmium, as a hazardous pollutant commonly present in the living environment, represents an important risk to human health due to its undesirable effects (oxidative stress, changes in activities of many enzymes, interactions with biomolecules including DNA and RNA) and consequent potential risk, making its detection very important. New and unique technological and biotechnological approaches for solving this problems are intensely sought. In this study, we used the commonly occurring potential pathogenic microorganism Staphylococcus aureus for the determination of markers which could be used for sensing of cadmium(II) ions. We were focused on monitoring the effects of different cadmium(II) ion concentrations (0, 1.25, 2.5, 5, 10, 15, 25 and 50 µg mL(-1)) on the growth and energetic metabolism of Staphylococcus aureus. Highly significant changes have been detected in the metabolism of thiol compounds-specifically the protein metallothionein (0.79-26.82 mmol/mg of protein), the enzyme glutathione S-transferase (190-5,827 µmol/min/mg of protein), and sulfhydryl groups (9.6-274.3 µmol cysteine/mg of protein). The ratio of reduced and oxidized glutathione indicated marked oxidative stress. In addition, dramatic changes in urease activity, which is connected with resistance of bacteria, were determined. Further, the effects of cadmium(II) ions on the metabolic pathways of arginine, ß-glucosidase, phosphatase, N-acetyl ß-d-glucosamine, sucrose, trehalose, mannitol, maltose, lactose, fructose and total proteins were demonstrated. A metabolomic profile of Staphylococcus aureus under cadmium(II) ion treatment conditions was completed seeking data about the possibility of cadmium(II) ion accumulation in cells. The results demonstrate potential in the application of microorganisms as modern biosensor systems based on biological components.

Phenolic profile of edible honeysuckle berries (genus lonicera) and their biological effects.

The current status of research on polyphenolic compounds in the berries of edible honeysuckle and their biological effects, including recommended utilization, are reviewed. The major classes of phenolic compounds in the blue berried honeysuckle are flavonols (quercetin, rutin, quercitrin) and flavanes (proanthocyanidins, catechins) and anthocyanins. Cyanidin-3-glucoside and cyanidin-3-rutinoside are considered as major anthocyanidins in edible honeysuckle berries. Such a high level of antioxidant activity in the berries of different species of the genus Lonicera is especially due to the high level of polyphenolic compounds, especially anthocyanins. These berries seem to be prospective sources of health-supporting phytochemicals that exhibit beneficial anti-adherence and chemo-protective activities, thus they may provide protection against a number of chronic conditions, e.g., cancer, diabetes mellitus, tumour growth or cardiovascular and neurodegenerative diseases.