High production of enantiopure (R,R)-2,3-butanediol from crude glycerol by Klebsiella pneumoniae with an engineered oxidative pathway and a two-stage agitation strategy.

BACKGROUND: (R,R)-2,3-butanediol (BDO) is employed in a variety of applications and is gaining prominence due to its unique physicochemical features. The use of glycerol as a carbon source for 2,3-BDO production in Klebsiella pneumoniae has been limited, since 1,3-propanediol (PDO) is generated during glycerol fermentation. RESULTS: In this study, the inactivation of the budC gene in K. pneumoniae increased the production rate of (R,R)-2,3-BDO from 21.92 ± 2.10 to 92.05 ± 1.20%. The major isomer form of K. pneumoniae (meso-2,3-BDO) was shifted to (R,R)-2,3-BDO. The purity of (R,R)-2,3-BDO was examined by agitation speed, and 98.54% of (R,R)-2,3-BDO was obtained at 500 rpm. However, as the cultivation period got longer, the purity of (R,R)-2,3-BDO declined. For this problem, a two-step agitation speed control strategy (adjusted from 500 to 400 rpm after 24 h) and over-expression of the dhaD gene involved in (R,R)-2,3-BDO biosynthesis were used. Nevertheless, the purity of (R,R)-2,3-BDO still gradually decreased over time. Finally, when pure glycerol was replaced with crude glycerol, the titer of 89.47 g/L of (R,R)-2,3-BDO (1.69 g/L of meso-2,3-BDO), productivity of 1.24 g/L/h, and yield of 0.35 g/g consumed crude glycerol was achieved while maintaining a purity of 98% or higher. CONCLUSIONS: This study is meaningful in that it demonstrated the highest production and productivity among studies in that produced (R,R)-2,3-BDO with a high purity in Klebsiella sp. strains. In addition, to the best of our knowledge, this is the first study to produce (R,R)-2,3-BDO using glycerol as the sole carbon source.

Production of highly pure R,R-2,3-butanediol for biological plant growth promoting agent using carbon feeding control of Paenibacillus polymyxa MDBDO.

BACKGROUND: Chemical fertilizers have greatly contributed to the development of agriculture, but alternative fertilizers are needed for the sustainable development of agriculture. 2,3-butanediol (2,3-BDO) is a promising biological plant growth promoter. RESULTS: In this study, we attempted to develop an effective strategy for the biological production of highly pure R,R-2,3-butanediol (R,R-2,3-BDO) by Paenibacillus polymyxa fermentation. First, gamma-ray mutagenesis was performed to obtain P. polymyxa MDBDO, a strain that grew faster than the parent strain and had high production of R,R-2,3-BDO. The activities of R,R-2,3-butanediol dehydrogenase and diacetyl reductase of the mutant strain were increased by 33% and decreased by 60%, respectively. In addition, it was confirmed that the carbon source depletion of the fermentation broth affects the purity of R,R-2,3-BDO through batch fermentation. Fed-batch fermentation using controlled carbon feeding led to production of 77.3 g/L of R,R-2,3-BDO with high optical purity (> 99% of C4 products) at 48 h. Additionally, fed-batch culture using corn steep liquor as an alternative nitrogen source led to production of 70.3 g/L of R,R-2,3-BDO at 60 h. The fed-batch fermentation broth of P. polymyxa MDBDO, which contained highly pure R,R-2,3-BDO, significantly stimulated the growth of soybean and strawberry seedlings. CONCLUSIONS: This study suggests that P. polymyxa MDBDO has potential for use in biological plant growth promoting agent applications. In addition, our fermentation strategy demonstrated that high-purity R,R-2,3-BDO can be produced at high concentrations using P. polymyxa.

Enhancing Diagnosis of Rotating Elements in Roll-to-Roll Manufacturing Systems through Feature Selection Approach Considering Overlapping Data Density and Distance Analysis.

Roll-to-roll manufacturing systems have been widely adopted for their cost-effectiveness, eco-friendliness, and mass-production capabilities, utilizing thin and flexible substrates. However, in these systems, defects in the rotating components such as the rollers and bearings can result in severe defects in the functional layers. Therefore, the development of an intelligent diagnostic model is crucial for effectively identifying these rotating component defects. In this study, a quantitative feature-selection method, feature partial density, to develop high-efficiency diagnostic models was proposed. The feature combinations extracted from the measured signals were evaluated based on the partial density, which is the density of the remaining data excluding the highest class in overlapping regions and the Mahalanobis distance by class to assess the classification performance of the models. The validity of the proposed algorithm was verified through the construction of ranked model groups and comparison with existing feature-selection methods. The high-ranking group selected by the algorithm outperformed the other groups in terms of training time, accuracy, and positive predictive value. Moreover, the top feature combination demonstrated superior performance across all indicators compared to existing methods.

Impact of Sensor Data Characterization with Directional Nature of Fault and Statistical Feature Combination for Defect Detection on Roll-to-Roll Printed Electronics.

Gravure printing, which is a roll-to-roll printed electronics system suitable for high-speed patterning of functional layers have advantages of being applied to flexible webs in large areas. As each of the printing procedure from inking to doctoring followed by ink transferring and setting influences the quality of the pattern geometry, it is necessary to detect and diagnose factors causing the printing defects beforehand. Data acquisition with three triaxial acceleration sensors for fault diagnosis of four major defects such as doctor blade tilting fault was obtained. To improve the diagnosis performances, optimal sensor selection with Sensor Data Efficiency Evaluation, sensitivity evaluation for axis selection with Directional Nature of Fault and feature variable optimization with Feature Combination Matrix method was applied on the raw data to form a Smart Data. Each phase carried out on the raw data progressively enhanced the diagnosis results in contents of accuracy, positive predictive value, diagnosis processing time, and data capacity. In the case of doctor blade tilting fault, the diagnosis accuracy increased from 48% to 97% with decreasing processing time of 3640 s to 16 s and the data capacity of 100 Mb to 5 Mb depending on the input data between raw data and Smart Data.

Theory for plasticity of face-centered cubic metals.

The activation of plastic deformation mechanisms determines the mechanical behavior of crystalline materials. However, the complexity of plastic deformation and the lack of a unified theory of plasticity have seriously limited the exploration of the full capacity of metals. Current efforts to design high-strength structural materials in terms of stacking fault energy have not significantly reduced the laborious trial and error works on basic deformation properties. To remedy this situation, here we put forward a comprehensive and transparent theory for plastic deformation of face-centered cubic metals. This is based on a microscopic analysis that, without ambiguity, reveals the various deformation phenomena and elucidates the physical fundaments of the currently used phenomenological correlations. We identify an easily accessible single parameter derived from the intrinsic energy barriers, which fully specifies the potential diversity of metals. Based entirely on this parameter, a simple deformation mode diagram is shown to delineate a series of convenient design criteria, which clarifies a wide area of material functionality by texture control.

Optimal Energy Efficiency Fairness of Nodes in Wireless Powered Communication Networks.

In wireless powered communication networks (WPCNs), it is essential to research energy efficiency fairness in order to evaluate the balance of nodes for receiving information and harvesting energy. In this paper, we propose an efficient iterative algorithm for optimal energy efficiency proportional fairness in WPCN. The main idea is to use stochastic geometry to derive the mean proportionally fairness utility function with respect to user association probability and receive threshold. Subsequently, we prove that the relaxed proportionally fairness utility function is a concave function for user association probability and receive threshold, respectively. At the same time, a sub-optimal algorithm by exploiting alternating optimization approach is proposed. Through numerical simulations, we demonstrate that our sub-optimal algorithm can obtain a result close to optimal energy efficiency proportional fairness with significant reduction of computational complexity.

Flavobacterium faecale sp. nov., an agarase-producing species isolated from stools of Antarctic penguins.

Taxonomic studies were performed on an agarase-producing strain, designated WV33(T), isolated from faeces of Antarctic penguins. Cells of strain WV33(T) were Gram-staining-negative, strictly aerobic, orange and rod-shaped. Strain WV33(T) displayed agarase activity and was able to utilize galactose as a sole carbon source. 16S rRNA gene sequence analysis revealed that strain WV33(T) was closely related to Flavobacterium algicola TC2(T) (98.0% similarity), F. frigidarium ATCC 700810(T) (96.9%) and F. frigoris LMG 21922(T) (96.1%). The predominant cellular fatty acids were iso-C(15 : 1) G, iso-C(15 : 0), C(15 : 0), C(16 : 0) and summed feature 3 (comprising iso-C(15 : 0) 2-OH and/or C(16 : 1)ω7c). Menaquinone 6 (MK-6) was the sole quinone identified, and the major pigment was zeaxanthin. The major polar lipid was phosphatidylethanolamine. DNA-DNA relatedness of strain WV33(T) with respect to its closest phylogenetic neighbours was 25% for F. algicola NBRC 102673(T), 23% for F. frigidarium DSM 17623(T) and 21% for F. frigoris DSM 15719(T). The DNA G+C content of strain WV33(T) was 37±0.6 mol%. Based on the phenotypic, chemotaxonomic and phylogenetic data, strain WV33(T) is concluded to represent a novel species of the genus Flavobacterium, for which the name Flavobacterium faecale sp. nov. is proposed. The type strain is WV33(T) ( = KCTC 32457(T) = CECT 8384(T)).

Control of Meniscus Formation Using an Electrohydrodynamics Module in Roll-to-Roll Systems for the Stable Coating of Functional Layers.

In fabricating functional layers, including thin-film transistors and conductive electrodes, using roll-to-roll (R2R) processing on polymer-based PET film, the instability of the slot-die coating meniscus under a high-speed web impedes functional layer formation with the desired thickness and width. The thickness profiles of the functional layers significantly impact the performance of the final products. In this study, we introduce an electrohydrodynamic (EHD)-based voltage application module to a slot-die coater to ensure the uniformity of the cross-machine direction (CMD) thickness profile within the functional layer and enable a stable, high-speed R2R process. The module can effectively control the spreadability of the meniscus by utilizing variations in the surface tension of the ink. The effectiveness of the EHD module was experimentally verified by applying a high voltage to a slot-die coater while keeping other process variables constant. As the applied voltage increases, the CMD thickness deviation reduces by 64.5%, and the production rate significantly increases (up to 300%), owing to the formation of a stable coated layer. The introduction of the EHD-based application module to the slot-die coater effectively controlled the spreadability of the meniscus, producing large-area functional layers.

Relative bioavailability of levodropropizine 60 mg capsule and syrup formulations in healthy male Korean volunteers: a singledose, randomized-sequence, open-label, two-way crossover study.

BACKGROUND: Levodropropizine is an oral non-opioid anti-tussive drug used in treatment of cough. A new generic 60 mg capsule formulation of levodropropizine has recently been developed. OBJECTIVES: The aim of this study was to assess the pharmacokinetics and bioequivalence of the test (capsule) formulation and reference (syrup) formulation of levodropropizine (60 mg) in healthy, fasted, male Korean volunteers. METHODS: This was a single-dose, randomized sequence, open-label, 2-period crossover study conducted in healthy male Korean volunteers in the fasted state at Kyung Hee University Medical Center (Seoul, Republic of Korea). A single oral dose of the test or reference formulation was followed by a 1-week washout period, after which subjects received the alternative formulation. Blood samples were collected at 0 (predose), 0.17, 0.33, 0.5, 0.75, 1, 1.5, 2, 3, 4, 6, 8, and 12 hours after study drug administration. Plasma concentration of levodropropizine was determined using a validated liquid chromatography tandem mass spectrometry (LCMS/ MS) method. The formulations were considered bioequivalent if the 90% CIs for C(max), AUC(0-12h) and AUC(0-∞) were within the predetermined bioequivalence range (80 - 125%, according to the guidelines of the Korea Food and Drug Administration (Korea FDA)). Tolerability was evaluated throughout the study based on vital sign measurements, laboratory analysis (blood biochemistry, hematology, hepatic function and urinalysis) and subject interviews concerning adverse events (AEs). RESULTS: A total of 36 male Korean subjects (mean (SD) age, 23.9 (2.4) years (range 19 - 30 years); height, 176.2 (6.1) cm (range 161 - 190 cm); weight, 69.8 (9.1) kg (range 54.0 - 92.2 kg); body mass index, 22.4 (2.1) kg/m2 (range 19.1 - 28.3 kg/m2)) was enrolled and completed the study. The mean values for C(max), t(max), AUC(0-12h), and AUC(0-∞) with the test formulation of levodropropizine were 331.51 ng/ml, 0.60 hours, 784.32 ng×h/ml, and 825.82 ng×h/ml, respectively; for the reference formulation, the values were 332.81 ng/ml, 0.44 hours, 726.46 ng×h/ml, and 769.46 ng×h/ ml, respectively. The 90% CIs for the logtransformed ratios of C(max) (92.74 - 111.24), AUC(0-12h) (104.31 - 113.67) and AUC(0-∞) (103.87 - 113.57) were within the predetermined range for the assumption of bioequivalence. No serious adverse events were reported. CONCLUSIONS: This single-dose (60 mg) study found that the test (capsule) and reference (syrup) formulations of levodropropizine met the regulatory criterion for assuming bioequivalence in these healthy, fasted, male Korean subjects. Both formulations were well tolerated in the population studied. Korea FDA registration number: BED-1784.

Rapid and sensitive LC-MS/MS method for determination of megestrol acetate in human plasma: application to a human pharmacokinetic study.

A rapid, simple and fully validated LC-MS/MS method was developed and validated for the determination of megestrol acetate in human plasma using tolbutamide as an internal standard (IS) after one-step liquid-liquid extraction with methyl-tert-butyl-ether. Detection was performed using electrospray ionization in positive ion multiple reaction monitoring mode by monitoring the transitions m/z 385.5 → 267.1 for megestrol acetate and m/z 271.4 → 155.1 for IS. Chromatographic separation was performed on a YMC Hydrosphere C18 column with an isocratic mobile phase, which consisted of 10 mm ammonium formate buffer (adjusted to pH 5.0 with formic acid)-methanol (60:40, v/v) at a flow rate of 0.4 mL/min. The achieved lower limit of quantitation (LLOQ) was 1 ng/mL (signal-to-noise ratio > 10) and the standard calibration curve for megestrol acetate was linear (r > 0.99) over the studied concentration range (1-2000 ng/mL). The proposed method was fully validated by determining its specificity, linearity, LLOQ, intra- and inter-day precision and accuracy, recovery, matrix effect and stability. The validated LC-MS/MS method was successfully applied for the evaluation of pharmacokinetic parameters of megestrol acetate after oral administration of a single dose 800 mg of megestrol acetate (Megace™) to five healthy Korean male volunteers under fed conditions.

Layer-by-Layer Engineered Flexible Functional Film Fabrication with Spreadability Control in Roll-to-Roll Manufacturing.

A roll-to-roll manufacturing system performs printing and coating on webs to mass-produce large-area functional films. The functional film of a multilayered structure is composed of layers with different components for performance improvement. The roll-to-roll system is capable of controlling the geometries of the coating and printing layers using process variables. However, research on geometric control using process variables is limited to single-layer structures only. This study entails the development of a method to proactively control the geometry of the upper coated layer by using the lower-layer coating process variable in the manufacture of a double-coated layer. The correlation between the lower-layer coating process variable and upper coated layer geometry was examined by analyzing the lower-layer surface roughness and spreadability of the upper-layer coating ink. The correlation analysis results demonstrate that tension was the dominant variable in the upper coated layer surface roughness. Additionally, this study found that adjusting the process variable of the lower-layer coating in a double-layered coating process could improve the surface roughness of the upper coating layer by up to 14.9%.

Web Wrinkle Defects due to Temperature Profile in Roll-to-Roll Manufacturing Systems.

The roll-to-roll manufacturing system is extensively used for mass producing products made of plastic, paper, and fabric in several traditional industries. When flexible substrates, also known as webs, are heated and transported inside the dryer, an inconsistent temperature distribution occurs on the material in the machine direction (MD) and cross-machine direction (CMD). If rollers are not aligned in parallel on the same plane in the roll-to-roll web handling process, or if roller misalignment exists, strain deviation occurs in the web, resulting in lateral displacement and web wrinkles. Therefore, this study examined a wrinkle, which is a thermal deformation that occurs when an inconsistent web temperature distribution is formed on the material inside a dryer. The changes in the elastic modulus and thermal expansion of the web were also examined. Experiments were conducted using a PET film, and its elastic modulus and thermal expansion were examined. The results showed that the presence of a web wrinkle defect can cause a thickness deviation in the functional layer manufactured on the web. Moreover, an appropriate operating speed should be set to reduce the CMD temperature deviation, thereby reducing instances of wrinkle defects.

Production of 1,2-propanediol from glycerol in Klebsiella pneumoniae GEM167 with flux enhancement of the oxidative pathway.

BACKGROUND: To support the sustainability of biodiesel production, by-products, such as crude glycerol, should be converted into high-value chemical products. 1,2-propanediol (1,2-PDO) has been widely used as a building block in the chemical and pharmaceutical industries. Recently, the microbial bioconversion of lactic acid into 1,2-PDO is attracting attention to overcome limitations of previous biosynthetic pathways for production of 1,2-PDO. In this study, we examined the effect of genetic engineering, metabolic engineering, and control of bioprocess factors on the production of 1,2-PDO from lactic acid by K. pneumoniae GEM167 with flux enhancement of the oxidative pathway, using glycerol as carbon source. RESULTS: We developed K. pneumoniae GEM167ΔadhE/pBR-1,2PDO, a novel bacterial strain that has blockage of ethanol biosynthesis and biosynthesized 1,2-PDO from lactic acid when glycerol is carbon source. Increasing the agitation speed from 200 to 400 rpm not only increased 1,2-PDO production by 2.24-fold to 731.0 ± 24.7 mg/L at 48 h but also increased the amount of a by-product, 2,3-butanediol. We attempted to inhibit 2,3-butanediol biosynthesis using the approaches of pH control and metabolic engineering. Control of pH at 7.0 successfully increased 1,2-PDO production (1016.5 ± 37.3 mg/L at 48 h), but the metabolic engineering approach was not successful. The plasmid in this strain maintained 100% stability for 72 h. CONCLUSIONS: This study is the first to report the biosynthesis of 1,2-PDO from lactic acid in K. pneumoniae when glycerol was carbon source. The 1,2-PDO production was enhanced by blocking the synthesis of 2,3-butanediol through pH control. Our results indicate that K. pneumoniae GEM167 has potential for the production of additional valuable chemical products from metabolites produced through oxidative pathways.

Effect of Radial Stress on the Nanoparticle-Based Electrolyte Layer in a Center-Wound Roll with Roll-to-Roll Systems.

Recently, slot-die coating based on the roll-to-roll process has been actively used to fabricate nanoparticle-based electrolyte layers because it is advantageous for high-speed processes and mass production of uniformly thick electrolyte layers. In this process, the fabricated electrolyte layer is stored as a wound roll throughout the rewinding process. We analyzed the defects and geometric changes in an electrolyte layer, i.e., gadolinium-doped cerium oxide (GDC), due to the radial stress in the wound roll. We found that the thickness of the coated layer could be decreased by increasing the radial stress, i.e., cracks can be generated in the coated layer if excessively high radial stress is applied to the wound-coated layer. More thickness changes and crack defects were generated with time due to the residual stress in the wound roll. Finally, we analyzed the effects of taper tension profiles on the defects of the coated layer in the wound roll and determined the taper tension profile to minimize defects.

Strain Optimization of Tensioned Web through Computational Fluid Dynamics in the Roll-to-Roll Drying Process.

Unpredictable web temperature distributions in the dryer and strain deviations in the cross-machine (CMD) and machine (MD) directions could hamper the manufacture of smooth functional layers on polymer-based webs through the roll-to-roll (R2R) continuous process system. However, research on this topic is limited. In this study, we developed a structural analysis model using the temperature distribution of the web as a boundary condition to analyze the drying mechanism of the dryer used in an R2R system. Based on the results of this model, we then applied structural modifications to the flow channel and hole density of the aluminum plate of the dryer. The model successfully predicted the temperature and strain distributions of the web inside the dryer in the CMD and MD by forming a tension according to the speed difference of the driven rolls at both ends of the span. Our structural improvements significantly reduced the temperature deviation of the moving web inside the dryer by up to 74% and decreased the strain deviation by up to 46%. The findings can help prevent web unevenness during the drying process of the R2R system, which is essential to minimize the formation of defects on functional layers built over polymer-based webs.

Transmittance Control of a Water-Repellent-Coated Layer on a Tensioned Web in a Roll-to-Roll Slot-Die Coating System.

Solar cells are important alternatives to fossil fuels for energy generation in today's world, where the demand for alternative, renewable sources of energy is increasing. However, solar cells, which are installed outdoors, are susceptible to pollution by environmental factors. A solution to overcome this limitation involves coating solar cell surfaces with functional coatings. In this study, we propose a transmittance control method for a tensioned web in a roll-to-roll, transparent, water-repellent film coating. First, we analyzed the effects of process conditions on the transmittance and contact angle of the transparent water-repellent film during roll-to-roll slot-die coating. It was confirmed that the tension was the most dominant factor, followed by the coating gap. Through the tension control, the transmittance was changed by 3.27%, and the contact angle of the DI water was changed by 17.7°. In addition, it was confirmed that the transmittance was changed by 0.8% and the contact angle of DI water by 3.9° via the coating gap control. Based on these results, a transmittance prediction model was developed according to the tension and coating gap, and was then verified experimentally. Finally, a water-repellent film with a high transmittance of 89.77% was obtained using this model.

Growth condition and bacterial community for maximum hydrolysis of suspended organic materials in anaerobic digestion of food waste-recycling wastewater.

This paper reports the effects of changing pH (5-7) and temperature (T, 40-60 degrees C) on the efficiencies of bacterial hydrolysis of suspended organic matter (SOM) in wastewater from food waste recycling (FWR) and the changes in the bacterial community responsible for this hydrolysis. Maximum hydrolysis efficiency (i.e., 50.5% reduction of volatile suspended solids) was predicted to occur at pH 5.7 and T = 44.5 degrees C. Changes in short-chain volatile organic acid profiles and in acidogenic bacterial communities were investigated under these conditions. Propionic and butyric acids concentrations increased rapidly during the first 2 days of incubation. Several band sequences consistent with Clostridium spp. were detected using denaturing gel gradient electrophoresis. Clostridium thermopalmarium and Clostridium novyi seemed to contribute to butyric acid production during the first 1.5 days of acidification of FWR wastewater, and C. thermopalmarium was a major butyric acid producer afterward. C. novyi was an important propionic acid producer. These two species appear to be important contributors to hydrolysis of SOM in the wastewater. Other acidogenic anaerobes, Aeromonas sharmana, Bacillus coagulans, and Pseudomonas plecoglossicida, were also indentified.

Numerical Modeling of Ink Widening and Coating Gap in Roll-to-Roll Slot-Die Coating of Solid Oxide Fuel Cell Electrolytic Layer.

Slot-die coatings are advantageous when used for coating large-area flexible devices; in particular, the coating width can be controlled and simultaneous multi-layer coatings can be processed. To date, the effects of ink widening and the coating gap on the coating thickness have only been considered in a few studies. To this end, we developed two mathematical models to accurately estimate the coating width and thickness that consider these two effects. We used root mean square deviation (RMSD) to experimentally verify the developed method. When the coating gap was increased, the coating width increased and the coating thickness decreased. Experimental results showed that the estimated performances of the coating width and thickness models were as high as 98.46% and 95.8%, respectively. We think that the developed models can be useful for determining the coating conditions according to the ink properties to coat a functional layer with user-defined widths and thicknesses in both lab- and industrial-scale roll-to-roll slot-die coating processes.

Enzymatic Synthesis of Glucosyl Rebaudioside A and its Characterization as a Sweetener.

Rebaudioside A was modified via glucosylation by recombinant dextransucrase of Leuconostoc lactis EG001 in Escherichia coli BL21 (DE3), forming single O-α-D-glucosyl-(1″→6') rebaudioside A with yield of 86%. O-α-D-glucosyl-(1″→6') rebaudioside A was purified using HPLC and Diaion HP-20 and its properties were characterized for possible use as a food ingredient. Almost 98% of O-α-D-glucosyl-(1″→6') rebaudioside A was dissolved after 15 days of storage at room temperature, compared to only 11% for rebaudioside A. Compared to rebaudioside A, O-α-D-glucosyl-(1″→6') rebaudioside A showed similar or improved acidic or thermal stability in commercial drinks. Thus, O-α-D-glucosyl-(1″→6') rebaudioside A could be used as a highly pure and improved sweetener with high stability in commercial drinks. PRACTICAL APPLICATION: The proposed method can be used to generate glucosyl rebaudioside A by enzymatic glucosylation. Simple glucosyl rebaudioside A exhibited high acid/thermal stability and improved sweetener in commercialized drinks. This method can be applied to obtain high value-added bioactive compounds by enzymatic modification.

Gamma-Aminobutyric Acid Production from a Novel Enterococcus avium JS-N6B4 Strain Isolated from Edible Insects.

Gamma-aminobutyric acid (GABA)-producing strains were isolated from four edible insects and subjected to 16S rRNA sequence analysis. Among the four GABA-producing bacteria, Enterococcus avium JS-N6B4 exhibited the highest GABA-production, while cultivation temperature, initial pH, aerobic condition, and mono-sodium glutamate (MSG) feeding were found to be the key factors affecting GABA production rate. The culture condition was optimized in terms of glucose, yeast extract, and MSG concentrations using response surface methodology (RSM). GABA production up to 16.64 g/l was obtained under the conditions of 7 g/l glucose, 45 g/l yeast extract, and 62 g/l MSG through the optimization of medium composition by RSM. Experimental GABA production was 13.68 g/l, which was close to the predicted value (16.64 g/l) calculated from the analysis of variance, and 2.79-fold higher than the production achieved with basic medium. Therefore, GABA-producing strains may help improve the GABA production in edible insects, and provide a new approach to the use of edible insects as effective food biomaterials.