A novel design, analysis and 3D printing of Ti-6Al-4V alloy bio-inspired porous femoral stem.

The current study is proposing a design envelope for porous Ti-6Al-4V alloy femoral stems to survive under fatigue loads. Numerical computational analysis of these stems with a body-centered-cube (BCC) structure is conducted in ABAQUS. Femoral stems without shell and with various outer dense shell thicknesses (0.5, 1.0, 1.5, and 2 mm) and inner cores (porosities of 90, 77, 63, 47, 30, and 18%) are analyzed. A design space (envelope) is derived by using stem stiffnesses close to that of the femur bone, maximum fatigue stresses of 0.3σys in the porous part, and endurance limits of the dense part of the stems. The Soderberg approach is successfully employed to compute the factor of safety Nf > 1.1. Fully porous stems without dense shells are concluded to fail under fatigue load. It is thus safe to use the porous stems with a shell thickness of 1.5 and 2 mm for all porosities (18-90%), 1 mm shell with 18 and 30% porosities, and 0.5 mm shell with 18% porosity. The reduction in stress shielding was achieved by 28%. Porous stems incorporated BCC structures with dense shells and beads were successfully printed.

Hybrid Nanocellulose-Copper (II) Oxide as Engine Oil Additives for Tribological Behavior Improvement.

Friction and wear are the main factors in the failure of the piston in automobile engines. The objective of this work was to improve the tribological behaviour and lubricant properties using hybrid Cellulose Nanocrystal (CNC) and Copper (II) oxide nanoparticles blended with SAE 40 as a base fluid. The two-step method was used in the hybrid nanofluid preparation. Three different concentrations were prepared in a range of 0.1% to 0.5%. Kinematic viscosity and viscosity index were also identified. The friction and wear behavior were evaluated using a tribometer based on ASTM G181. The CNC-CuO nano lubricant shows a significant improvement in term of viscosity index by 44.3-47.12% while for friction, the coefficient of friction (COF) decreases by 1.5%, respectively, during high and low-speed loads (boundary regime), and 30.95% during a high-speed, and low load (mixed regime). The wear morphologies results also show that a smoother surface was obtained after using CNC-CuO nano lubricant compared to SAE 40.

Finite element study of functionally graded porous femoral stems incorporating body-centered cubic structure.

The mismatch between stiffness of the femoral dense stem and host bone causes complications to patients, such as aseptic loosening and bone resorption. Three-dimensional finite-element models of homogeneous porous (HGP) and functionally graded porous (FGP) stems incorporating body-centered cubic (BCC) structures are proposed in this article as an alternative to the dense stems. The relationship between the porosity and strut thickness of the BCC structure was developed to construct the finite-element models. Three levels of porosities (20%, 50%, and 80%) were modeled in HGP and FGP stems. The porosity of the stems was decreased distally according to the sigmoid function (n = 0.1, n = 1 and n = 10) with 3 grading exponents. The results showed that FGP stems transferred 120%-170% higher stresses to the femur (Gruen zone 7) as compared to the solid stem. Conversely, the stresses in HGP and FGP stems were 12%-34% lower than the dense stem. The highest micromotions (105-147 µm) were observed for stems of 80% overall porosity, and the lowest (42-46 µm) was for stems of 20% overall porosity. Finally, FGP stems with a grading exponent of n = 10 resulted in an 11%-28% reduction in micromotions.

Thermal properties analysis and thermal cycling of HITEC molten salt with h-BN nanoparticles for CSP thermal energy storage applications.

Molten salts are the operational fluid for most concentrated solar power (CSP) systems, which has attracted more attention among the scientific community due to the augmentation of their properties with the doping of nanoparticles. Hexagonal boron nitride (h-BN) nanoparticles were dispersed in HITEC molten salt to create a novel nanofluid and evaluate the h-BN nanoparticles' influence on HITEC thermophysical properties. The influence of nanoparticle concentration (0.1, 0.5, and 1wt.%) of h-BN and HITEC was studied in this research. HITEC and nano-enhanced HITEC molten salt (NEHMS) were characterized using energy-dispersive X-ray spectroscopy (EDX), field emission scanning electron microscopy (FESEM), and Fourier transform infrared spectroscopy (FT-IR). Specific heat capacity, latent heat, and melting temperature were assessed using differential scanning calorimetry (DSC). The maximum working temperature was evaluated with thermogravimetric analysis (TGA). The ideal nanoparticle concentration is 0.1 wt.% h-BN, which results in a 27% increase in heat capacity, a 72% increase in latent heat, and a 7% enhancement in thermal stability. The thermal cycling stability test proved the stability of the enhanced thermophysical properties. The material characterization revealed that the samples with improved thermophysical properties have a homogeneous dispersion of nanoparticles with minor nanoparticle agglomeration. The system advisor model (SAM) simulation comparison of the optimum sample with solar salt and HITEC salt revealed that using the optimum sample increases CSP plant efficiency by 0.4% and reduces power costs by 0.13¢/kWh.

Thermohydraulic performance investigation of a heat exchanger with combined effect of ribbed insert and Therminol55/MXene+ Al2O3 nanofluid: A numerical two-phase approach.

MXene-based nanofluids are novel trends with improved dispersion stability and thermophysical characteristics over previously established nanofluids. In the present work, the thermohydraulic characteristics of a double pipe heat exchanger (DPHEX) with a Therminol55(TH55)/MXene + Al2O3 nanofluid and various geometrically shaped (triangular, rectangular) ribbed twisted tape (TT) inserts are numerically investigated using the ANSYS Fluent interface. A counter flow arrangement with three different types of inserts (RRTT, TRTT, TT) and TH55/MXene + Al2O3 nanofluid at 0.20 wt% are studied inside the heat exchanger. Adding ribbed inserts to the conventional TT insert enhances the turbulence intensity by creating extra vortices. The thermal boundary layer grows thinner due to increased axial and radial velocity. Due to the substantial flow obstruction, adding ribs increases the overall pressure drop between the inlet and outlet. The maximum increase in Nu is 11.04 % using nanofluid instead of water, whereas the combination of insert and nanofluid exhibited up to 105 % enhancement for rectangular-ribbed TT compared to the plain tube. Nevertheless, the pressure decrease is found to be maximum in rectangular-ribbed TT because of significant flow disruption. This was likewise true with triangular-ribbed TT and TT insert. According to the PEC assessment, the RRTT insert had a maximum PEC value of 1.67 greater than TRTT and traditional TT for both TH55 and nanofluid flowing inside the tube. To summarize, the combination of TH55/MXene + Al2O3 RRTT insert may be a promising choice for improving heat exchanger performance in a new generation efficient thermal system.

Effect of porous density of twisted tape inserts on heat transfer performance inside a closed conduit.

This study examines the impact of varying the porosity density of twisted tape inserts (TTI) on the temperature distribution, fluid velocities, heat transfer coefficients (HTC), Nusselt numbers (Nu), turbulent kinetic energy (TKE), and performance from 5000 to 12500 Reynolds numbers (Re). The entire process involved the design of TTIs and double pipe heat exchangers using SolidWorks. Subsequently, a three-dimensional fluid flow model was employed to solve equations related to energy mass, energy, and momentum within the ANSYS Fluent interfaces. The findings highlight the noteworthy impact of high porosity TTIs, which consistently reduce temperature spans, increase fluid velocities, and greatly HTC and Nu when compared to low porosity TTI, typical TTI, and plain tubes. Furthermore, high porosity TTI significantly increases TKE, indicating increased fluid turbulence and higher heat transfer efficiency, especially at Re = 12500. The assessment of PEC emphasizes the superiority of high porosity TTI, demonstrating their significant performance increase potential of over 6.44 % over low porosity TTI and a staggering 62.5 % above typical TTI. In conclusion, high porosity TTI emerges as a potential solution for improving heat transfer efficiency and overall system performance in a variety of industrial applications, promising enhanced energy efficiency and superior performance.

Influence of PODE1 additive into ethanol-gasoline blends (E10) on fuel properties and phase stability.

Polyoxymethylene dimethyl ethers (PODEn, n = 1-8) as an oxygenated fuel are a promising alternative fuel with a high oxygen concentration, a low C:H ratio, and no C-C bonds in their chemical structure. This could lead to smoke-free combustion. In this study, we chose to focus on PODE1 because of its lower cetane number, which makes it more suitable for use in spark ignition (SI) engines. However, its lower boiling point and octane number remain challenges. A low boiling point may lead to high vapour pressure and require storage and handling comparable to gaseous fuels. We investigated the effect of adding PODE1 to gasoline-ethanol blends (E10) on fuel properties, including distillation curve, octane number, phase stability, C/O/H ratio, heat of combustion, kinematic viscosity, and density. Our results showed that the blended fuels of E10 and PODE1 are stable up to 10 % PODE1, and there was no phase separation. Additionally, up to 10 % PODE1 additive had no significant side effect on the fuel properties of E10, particularly boiling point and octane number. Thus, work offers creative points by proposing a new candidate for additive fuel to gasoline-ethanol blends, which contributes to reducing the soot emission of GDI engines.

Harnessing Nature's Ingenuity: A Comprehensive Exploration of Nanocellulose from Production to Cutting-Edge Applications in Engineering and Sciences.

Primary material supply is the heart of engineering and sciences. The depletion of natural resources and an increase in the human population by a billion in 13 to 15 years pose a critical concern regarding the sustainability of these materials; therefore, functionalizing renewable materials, such as nanocellulose, by possibly exploiting their properties for various practical applications, has been undertaken worldwide. Nanocellulose has emerged as a dominant green natural material with attractive and tailorable physicochemical properties, is renewable and sustainable, and shows biocompatibility and tunable surface properties. Nanocellulose is derived from cellulose, the most abundant polymer in nature with the remarkable properties of nanomaterials. This article provides a comprehensive overview of the methods used for nanocellulose preparation, structure-property and structure-property correlations, and the application of nanocellulose and its nanocomposite materials. This article differentiates the classification of nanocellulose, provides a brief account of the production methods that have been developed for isolating nanocellulose, highlights a range of unique properties of nanocellulose that have been extracted from different kinds of experiments and studies, and elaborates on nanocellulose potential applications in various areas. The present review is anticipated to provide the readers with the progress and knowledge related to nanocellulose. Pushing the boundaries of nanocellulose further into cutting-edge applications will be of particular interest in the future, especially as cost-effective commercial sources of nanocellulose continue to emerge.

An Approach for the Optimization of Thermal Conductivity and Viscosity of Hybrid (Graphene Nanoplatelets, GNPs: Cellulose Nanocrystal, CNC) Nanofluids Using Response Surface Methodology (RSM).

Response surface methodology (RSM) is used in this study to optimize the thermal characteristics of single graphene nanoplatelets and hybrid nanofluids utilizing the miscellaneous design model. The nanofluids comprise graphene nanoplatelets and graphene nanoplatelets/cellulose nanocrystal nanoparticles in the base fluid of ethylene glycol and water (60:40). Using response surface methodology (RSM) based on central composite design (CCD) and mini tab 20 standard statistical software, the impact of temperature, volume concentration, and type of nanofluid is used to construct an empirical mathematical formula. Analysis of variance (ANOVA) is applied to determine that the developed empirical mathematical analysis is relevant. For the purpose of developing the equations, 32 experiments are conducted for second-order polynomial to the specified outputs such as thermal conductivity and viscosity. Predicted estimates and the experimental data are found to be in reasonable arrangement. In additional words, the models could expect more than 85% of thermal conductivity and viscosity fluctuations of the nanofluid, indicating that the model is accurate. Optimal thermal conductivity and viscosity values are 0.4962 W/m-K and 2.6191 cP, respectively, from the results of the optimization plot. The critical parameters are 50 °C, 0.0254%, and the category factorial is GNP/CNC, and the relevant parameters are volume concentration, temperature, and kind of nanofluid. From the results plot, the composite is 0.8371. The validation results of the model during testing indicate the capability of predicting the optimal experimental conditions.

Insight into the Investigation of Diamond Nanoparticles Suspended Therminol®55 Nanofluids on Concentrated Photovoltaic/Thermal Solar Collector.

Nanofluids are identified as advanced working fluids in the solar energy conversion field with superior heat transfer characteristics. This research work introduces carbon-based diamond nanomaterial and Therminol®55 oil-based nanofluids for implementation in a concentrated photovoltaic/thermal (CPV/T) solar collector. This study focuses on the experimental formulation, characterization of properties, and performance evaluation of the nanofluid-based CPV/T system. Thermo-physical (thermal conductivity, viscosity, and rheology), optical (UV-vis and FT-IR), and stability (Zeta potential) properties of the formulated nanofluids are characterized at 0.001-0.1 wt.% concentrations of dispersed particles using experimental assessment. The maximum photo-thermal energy conversion efficiency of the base fluid is improved by 120.80% at 0.1 wt.%. The thermal conductivity of pure oil is increased by adding the nanomaterial. The highest enhancement of 73.39% is observed for the TH-55/DP nanofluid. Furthermore, dynamic viscosity decreased dramatically across the temperature range studied (20-100 °C), and the nanofluid exhibited dominant Newtonian flow behavior, with viscosity remaining nearly constant up to a shear rate of 100 s-1. Numerical simulations of the nanofluid-operated CPV/T collector have disclosed substantial improvements. At a concentrated solar irradiance of 5000 W/m2 and an optimal flow rate of 3 L/min, the highest thermal and electrical energy conversion efficiency enhancements are found to be 11 and 1.8%, respectively.