Efficient treatment of oily wastewater, antibacterial activity, and photodegradation of organic dyes using biosynthesized Ag@Fe3O4 nanocomposite.

A significant waste (e.g., high oil content and pollutants such as heavy metals, dyes, and microbial contaminants) in water is generated during crude oil extraction and industrial processes, which poses environmental challenges. This study explores the potential of Ag@Fe3O4 nanocomposite (NC) biosynthesized using the aqueous leaf extract of Laurus nobilis for the treatment of oily wastewater. The NC was characterized using ultraviolet-visible (UV-Vis) spectrophotometry, Scanning Electron Microscopy (SEM), Fourier Transformed Infrared (FTIR) and X-Ray Diffraction (XRD) spectroscopies. The crystalline structure of the NC was determined to be face-centered cubic with an average size of 42 nm. Ag@Fe3O4 NC exhibited significant degradation (96.8%, 90.1%, and 93.8%) of Rose Bengal (RB), Methylene Blue (MB), and Toluidine Blue (TB), respectively, through a reduction reaction lasting 120 min at a dye concentration of 10 mg/L. The observed reaction kinetics followed a pseudo-first-order model, with rate constants (k-values) of 0.0284 min-1, 0.0189 min-1, and 0.0212 min-1 for RB, MB, and TB, respectively. The fast degradation rate can be attributed to the low band gap (1.9 eV) of Ag@Fe3O4 NC. The NC elicited an impressive effectiveness (99-100%, 98.0%, and 91.8% within 30 min) in removing, under sunlight irradiation, several heavy metals, total petroleum hydrocarbons (TPH), and total suspended solids (TSS) from the oily water samples. Furthermore, Ag@Fe3O4 NC displayed potent antibacterial properties and a good biocompatibility. These findings contribute to the development of efficient and cost-effective methods for wastewater treatment and environmental remediation.

Biosynthesis MgO and ZnO nanoparticles using chitosan extracted from Pimelia Payraudi Latreille for antibacterial applications.

Chitosan (CS) is one of the most abundant biopolymers in nature with superior properties such as biocompatibility, biodegradability, lack of toxicity, antimicrobial activity, acceleration of wound healing, and stimulation of the immune system. In this study, chitosan was extracted from the exoskeletons of beetles (Pimelia payraudi latreille) and then used for the biosynthesis of highly pure MgO NPs and ZnO NPs by a facile greener route. The extracted chitosan exhibited excellent physicochemical properties, including high extraction yield (39%), high degree of deacetylation (90%), low ash content (1%), high fat-binding capacity (366%), and unusual crystallinity index (51%). The MgO NPs and ZnO NPs exhibited a spherical morphology with crystallite sizes of 17 nm and 29 nm, particle sizes of about 20-70 nm and 30-60 nm, and band gap energies of 4.43 and 3.34 eV, respectively. Antibacterial assays showed that the extracted chitosan exhibited high antibacterial activity against Gram-positive and -negative bacteria, while ZnO NPs showed much stronger antibacterial activity against Gram-positive bacteria than against Gram-negative bacteria. For MgO NPs, the antibacterial activity against Gram-positive bacteria was lower than against Gram-negative bacteria. The results suggest that the synthesized MgO NPs and ZnO NPs are excellent antibacterial agents for therapeutic applications.

Chitosan extraction from Amanita phalloides: yield, crystallinity, degree of deacetylation, azo dye removal and antibacterial properties.

Chitosan, a biopolymer obtained from chitin, is known for its remarkable adsorption abilities for dyes, drugs, and fats, and its diverse array of antibacterial characteristics. This study explores the extraction and characterization of chitosan from the mycelium of Amanita phalloides. The moisture content, ash content, water binding capacity, fat binding capacity, and degree of deacetylation of the extracted chitosan were determined. The chitosan exhibited a high yield of 70%, crystallinity of 49.07%, a degree of deacetylation of 86%, and potent antimicrobial properties against both Gram-negative and Gram-positive bacteria. The study also examined the adsorption capabilities of chitosan to remove methylene blue (MB) dye by analysing specific factors like pH, reaction time, and MB concentration using the response surface model. The highest degree of MB dye removal was 91.6% at a pH of 6, a reaction time of around 60 min and an initial dye concentration of 16 ppm. This experimental design can be applied for chitosan adsorption of other organic compounds such as dyes, proteins, drugs, and fats.

Nanostructured Mn@NiO composite for addressing multi-pollutant challenges in petroleum-contaminated water.

Efficient catalysts play a pivotal role in advancing eco-friendly water treatment strategies, particularly in the removal of diverse organic contaminants found in water-petroleum sources. This study addresses the multifaceted challenges posed by contaminants, encompassing a spectrum of heavy metals such as As, Cd, Cr, Mn, Mo, Ni, Pb, Sb, Se, and Zn alongside pollutants like oily water (OIW), total suspended solids (TSS), chemical oxygen demand (COD), dyes, and pharmaceuticals, posing threats to both aquatic and terrestrial ecosystems. Herein, we present the synthesis of biogenically derived Mn@NiO nanocomposite (NC) photocatalysts, a sustainable methodology employing an aqueous Rosmarinus officinalis L. extract, yielding particles with a size of 36.7 nm. The catalyst demonstrates exceptional efficacy in removing heavy metals, achieving rates exceeding 99-100% within 30 min, alongside notable removal efficiencies for OIW (98%), TSS (87%), and COD (98%). Furthermore, our photodegradation experiments showed remarkable efficiencies, with 94% degradation for Rose Bengal (RB) and 96% for methylene blue (MB) within 120 min. The degradation kinetics adhere to pseudo-first-order behavior, with rate constants of 0.0227 min-1 for RB and 0.0370 min-1 for MB. Additionally, the NC exhibits significant antibiotic degradation rates of 97% for cephalexin (CEX) and 96% for amoxicillin (AMOX). The enhanced photocatalytic performance is attributed to the synergistic interplay between the Mn and NiO nanostructures, augmenting responsiveness to sunlight while mitigating electron-hole pair recombination. Notably, the catalyst demonstrates outstanding stability and reusability across multiple cycles, maintaining its stable nanostructure without compromise.

Improved Synthesis of Cu2O NPs and Ascorbic Acid-Modified Derivatives for Adsorption of Brilliant Cresyl Blue: Surface and Reusability Studies.

This study addresses the critical need for efficient and recyclable photocatalysts for water treatment applications by presenting a novel approach for the synthesis and characterization of copper (I) oxide (Cu2O) nanoparticles modified with ascorbic acid (Cu2O/AA). The motivation for this research stems from the increasing concern about environmental pollution caused by organic pollutants, such as Brilliant Cresyl Blue (BCB), and the necessity for sustainable solutions to mitigate this issue. Through comprehensive characterization techniques including Ultraviolet-Visible spectroscopy (UV-Vis), Fourier Transform Infrared spectroscopy (FTIR), X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), zeta potential measurements, and Brunauer-Emmett-Teller (BET) analysis, we demonstrate a significant modification to the electronic structure, enhancing the photocatalytic activity of Cu2O/AA. BET analysis revealed a mesoporous structure with a specific surface area of 2.7247 m2/g for Cu2O/AA, further emphasizing its potential for enhanced catalytic performance. The photocatalytic degradation studies showcased remarkable efficiency improvements, with degradation coefficients of 30.8% and 73.12% for Cu2O NPs and Cu2O/AA NC, respectively, within a 120 min timeframe. Additionally, recyclability experiments indicated sustained efficiency over five consecutive cycles, with both catalysts retaining crystalline integrity. These findings underscore the promising potential of Cu2O/AA nanoparticles as highly efficient and recyclable photocatalysts for the degradation of organic pollutants, offering superior performance compared to pure Cu2O NPs and addressing the pressing need for sustainable water treatment solutions.

Use of Insect-Derived Chitosan for the Removal of Methylene Blue Dye from Wastewater: Process Optimization Using a Central Composite Design.

Insects are a readily available source of chitosan due to their high reproductive rates, ease of breeding, and resistance to changes in their ecosystem. This study aimed to extract chitosan from several widespread insects: Blaps lethifera (CS-BL), Pimelia fernandezlopezi (CS-PF), and Musca domestica (CS-MD). The study was also extended to using the obtained chitosans in removing methylene blue dye (MB) from wastewater. The source of the chitosan, the initial concentration of MB dye, and the reaction time were chosen as the working parameters. The experiments were designed using a central composite design (CCD) based on the dye removal efficiency as the response variable. The experimental work and statistical calculation of the CCD showed that the dye removal efficiency ranged from 35.9% to 88.7% for CS-BL, from 18.8% to 47.1% for CS-PF, and from 10.3% to 29.0% for CS-MD at an initial MB concentration of 12.79 mg/L. The highest methylene blue dye removal efficiency was 88.7% for CS-BL at a reaction time of 120 min. This indicates that the extraction of chitosan from insects (Blaps lethifera) and its application in dye removal is a promising, environmentally friendly, economical, biodegradable, and cost-effective process. Furthermore, the CCD is a statistical experimental design technique that can be used to optimize process variables for removing other organic pollutants using chitosan.

Removal of hydrocarbons and heavy metals from petroleum water by modern green nanotechnology methods.

Considered heavy metals, such as As(III), Bi(II), Cd(II), Cr(VI), Mn(II), Mo(II), Ni(II), Pb(II), Sb(III), Se(-II), Zn(II), and contaminating chemical compounds (monocyclic aromatic hydrocarbons such as phenolic or polycyclic derivatives) in wastewater (petrochemical industries: oil and gas production plants) are currently a major concern in environmental toxicology due to their toxic effects on aquatic and terrestrial life. In order to maintain biodiversity, hydrosphere ecosystems, and people, it is crucial to remove these heavy metals and polluting chemical compounds from the watery environment. In this study, different Nanoparticles (α-Fe2O3, CuO, and ZnO) were synthesized by green synthesis method using Portulaca oleracea leaf extract and characterized by UV-Vis spectrophotometers, FTIR spectroscopy, X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) techniques in order to investigate morphology, composition, and crystalline structure of NPs, these were then used as adsorbent for the removal of As(III), Bi(II), Cd(II), Cr(VI), Mn(II), Mo(II), Ni(II), Pb(II), Sb(III), Se(-II), and Zn(II) from wastewater, and removal efficiencies of were obtained 100% under optimal conditions.

The Recent Progress on Silver Nanoparticles: Synthesis and Electronic Applications.

Nanoscience enables researchers to develop new and cost-effective nanomaterials for energy, healthcare, and medical applications. Silver nanoparticles (Ag NPs) are currently increasingly synthesized for their superior physicochemical and electronic properties. Good knowledge of these characteristics allows the development of applications in all sensitive and essential fields in the service of humans and the environment. This review aims to summarize the Ag NPs synthesis methods, properties, applications, and future challenges. Generally, Ag NPs can be synthesized using physical, chemical, and biological routes. Due to the great and increasing demand for metal and metal oxide nanoparticles, researchers have invented a new, environmentally friendly, inexpensive synthetic method that replaces other methods with many defects. Studies of Ag NPs have increased after clear and substantial support from governments to develop nanotechnology. Ag NPs are the most widely due to their various potent properties. Thus, this comprehensive review discusses the different synthesis procedures and electronic applications of Ag NPs.

Green Synthesized of Ag/Ag2O Nanoparticles Using Aqueous Leaves Extracts of Phoenix dactylifera L. and Their Azo Dye Photodegradation.

In this study, silver/silver oxide nanoparticles (Ag/Ag2O NPs) were successfully biosynthesized using Phoenix dactylifera L. aqueous leaves extract. The effect of different plant extract/precursor contractions (volume ratio, v/v%) on Ag/Ag2O NP formation, their optical properties, and photocatalytic activity towards azo dye degradation, i.e., Congo red (CR) and methylene blue (MB), were investigated. X-ray diffraction confirmed the crystalline nature of Ag/Ag2O NPs with a crystallite size range from 28 to 39 nm. Scanning electron microscope images showed that the Ag/Ag2O NPs have an oval and spherical shape. UV-vis spectroscopy showed that Ag/Ag2O NPs have a direct bandgap of 2.07-2.86 eV and an indirect bandgap of 1.60-1.76 eV. Fourier transform infrared analysis suggests that the synthesized Ag/Ag2O NPs might be stabilized through the interactions of -OH and C=O groups in the carbohydrates, flavonoids, tannins, and phenolic acids present in Phoenix dactylifera L. Interestingly, the prepared Ag/Ag2O NPs showed high catalytic degradation activity for CR dye. The photocatalytic degradation of the azo dye was monitored spectrophotometrically in a wavelength range of 250-900 nm, and a high decolorization efficiency (84.50%) was obtained after 50 min of reaction. As a result, the use of Phoenix dactylifera L. aqueous leaves extract offers a cost-effective and eco-friendly method.