High spatial-density, cladding-pumped 6-mode 7-core fiber amplifier for C-band operation.

We present a C-band 6-mode 7-core fiber amplifier in an all-fiberized cladding-pumped configuration for space division multiplexed transmission supporting a record 42 spatial channels. With optimized fiber components (e.g. passively cooled pump laser diode, pump coupler, pump stripper), high power multimode pump light is coupled to the active fiber without any noticeable thermal degradation and an average gain of 18 dB and noise figure of 5.4 dB are obtained with an average differential modal gain of 3.4 dB.

Study on the temperature dependent characteristics of O-band bismuth-doped fiber amplifier.

We report the temperature dependent performance of an O-band bismuth (Bi)-doped fiber amplifier (BDFA) in the temperature range from -60 to +80°C. At room temperature, maximum gains of 27 and 40 dB with noise figures (NFs) of 4.3 and 4.8 dB are measured for -23 dBm signal power in the single and double pass BDFA, respectively. An increment in gain and reduction in NF is observed as the ambient temperature of the BDFA is reduced. In the double pass BDFA, the temperature dependent gain coefficient from -60 to +80°C is found to be around -0.02 and -0.03 dB/°C across the wavelength band of 1300-1360 nm for -10 and -23 dBm signal powers, respectively. We also study the gain and NF characteristics with pump power and signal power at different temperatures, and a maximum gain of 45 dB is obtained at -60°C for -30 dBm signal power.

40 dB gain all fiber bismuth-doped amplifier operating in the O-band.

In this Letter, we investigate and compare the gain and noise figure characteristics of bismuth (Bi)-doped fiber amplifiers configured in both single and double signal pass implementations. A maximum gain of 25 dB and a noise figure of 4 dB is measured at 1360 nm in the single pass configuration for -23 dBm input signal power, whereas in the double pass configuration the gain of the amplifier is improved significantly by 14 dB allowing us to achieve a gain of 39 dB with a noise figure of 5 dB. To the best of our knowledge, this is the highest gain reported to date using Bi-doped fiber as a gain medium. Furthermore, we also study the gain and noise figure dependency on pump power, signal power, and pump wavelength for the double pass amplifier configuration. We observed similar gain and noise figure performance in the double pass configuration to that of the single pass configuration but with the benefit of less pump power and a shorter length of the Bi-doped fiber.

Demonstration of opposing thermal sensitivities in hollow-core fibers with open and sealed ends.

The output phase and propagation time of an optical signal propagating through a hollow-core optical fiber (HCF) drift with changes in environmental temperature significantly less than in conventional optical fibers. In all earlier experimental studies, however, the simplifying assumption was made that the thermo-optic effect of air was negligible. In this Letter, we present, to the best of our knowledge, the first experimental demonstration that the air inside a HCF core can make an appreciable contribution to the fiber's thermal sensitivity with the performance depending on whether the fiber is open to the atmosphere or sealed at both ends (e.g., spliced to solid fiber pigtails). We measure both the sensitivity of the accumulated phase as well as the signal propagation time for both open and sealed HCF and show that these are opposite in sign. Most importantly, we show that the thermal sensitivity contribution from the air inside an open HCF has the sign opposite to the effect of fiber elongation (which is otherwise the dominant effect responsible for the overall thermal sensitivity of HCF). We then go on to show that these two effects can be used to balance each other out in order to achieve zero thermal sensitivity for both accumulated phase and propagation time. We demonstrate this property experimentally over a large spectral range.

Point-by-point femtosecond laser micro-processing of independent core-specific fiber Bragg gratings in a multi-core fiber.

Four 3rd order fiber Bragg gratings were inscribed into separate cores of a 7 core multi-core fiber using the point-by-point inscription technique. A 1030 nm, 206 ± 5 fs laser was used, operating at a frequency of 1 kHz and pulse energy of 2.1 ± 0.2 µJ. Independent Bragg resonances at λB = 1541.01 ± 0.02, 1547.82 ± 0.02, 1532.66 ± 0.02, and 1537.42 ± 0.02 nm and extinction ratios of 13.97 ± 0.4, 16.02 ± 0.4, 10.08 ± 0.4 and 13.40 ± 0.4 dB were recorded. Our data analysis shows that refractive index changes, Δn, of the order 10-3 were induced. Core-specific inscription of fiber Bragg gratings in a multi-core fiber can provide a flexible and versatile platform to address the needs of recent space division multiplexed transmission and optical sensor networks.

Raman-shifted wavelength-selectable pulsed fiber laser with high repetition rate and high pulse energy in the visible.

A high-pulse-energy, diffraction-limited, wavelength-selectable, visible source, based on Raman frequency shifting of a frequency-doubled Yb-doped fiber laser, has been studied. The relative length-scaling laws of Raman gain and self-phase modulation push the design towards short fiber lengths with large core size. It is experimentally demonstrated that the Raman clean-up effect in a graded-index multi-mode fiber is not sufficient to obtain diffraction-limited beam quality in the short fiber length. Thus, a large-core photonic crystal fiber is used to maintain diffraction-limited performance and output pulse energies of ~1 µJ, at a 1-MHz repetition rate and 1.3-ns pulse-width are successfully achieved. This step-tunable visible source should find applications in photoacoustic microscopy.

Full quadrature regeneration of QPSK signals using sequential phase sensitive amplification and parametric saturation.

We demonstrate all-optical regeneration of both the phase and the amplitude of a 10 GBaud quadrature phase shift keying (QPSK) signal using two nonlinear stages. First we regenerate the phase using a wavelength converting phase sensitive amplifier and then we regenerate the amplitude using a saturated single-pump parametric amplifier, returning the signal to its original wavelength at the same time. We exploit the conjugating nature of the two processing stages to eliminate the intrinsic SPM distortion of the system, further improving performance.

Wavelength conversion of complex modulation formats in a compact SiGe waveguide.

We report a nonlinear signal processing system based on a SiGe waveguide suitable for high spectral efficiency data signals. Four-wave-mixing (FWM)-based wavelength conversion of 10-Gbaud 16-Quadrature amplitude modulated (QAM) and 64-QAM signals is demonstrated with less than -10-dB conversion efficiency (CE), 36-dB idler optical signal-to-noise ratio (OSNR), negligible bit error ratio (BER) penalty and a 3-dB conversion bandwidth exceeding 30nm. The SiGe device was CW-pumped and operated in a passive scheme without giving rise to any two-photon absorption (TPA) effects.

49.6 Gb/s direct detection DMT transmission over 40 km single mode fibre using an electrically packaged silicon photonic modulator.

We present the characterization of a silicon Mach-Zehnder modulator with electrical packaging and show that it exhibits a large third-order intermodulation spurious-free dynamic range (> 100 dB Hz2/3). This characteristic renders the modulator particularly suitable for the generation of high spectral efficiency discrete multi-tone signals and we experimentally demonstrate a single-channel, direct detection transmission system operating at 49.6 Gb/s, exhibiting a baseband spectral efficiency of 5 b/s/Hz. Successful transmission is demonstrated over various lengths of single mode fibre up to 40 km, without the need of any amplification or dispersion compensation.

Thulium-fiber-laser-pumped, high-peak-power, picosecond, mid-infrared orientation-patterned GaAs optical parametric generator and amplifier.

We report a high-peak-power, picosecond, mid-infrared optical parametric generator (OPG) and optical parametric amplifier (OPA) based on orientation-patterned gallium arsenide pumped by a thulium:fiber master-oscillator-power-amplifier employing direct diode-seeded amplification. An OPG tuning range of 2550-2940 nm (signal) and 5800-8300 nm (idler) is demonstrated with peak powers as high as 3 (signal) and 2 kW (idler), and with pulse energies of 0.26 and 0.16 µJ, respectively. When seeded with a 0.6 cm-1 linewidth tunable Cr:ZnSe laser, the OPA idler linewidth is narrowed to 1.4 cm-1 and a small-signal parametric gain of 60 dB is achieved. A maximum peak power of 13.3 (signal) and 3.2 kW (idler) is obtained at an overall conversion efficiency of 36%. The corresponding maximum pulse energies for the signal and idler are 1.07 and 0.26 µJ, respectively.

Radially and azimuthally polarized nanosecond Yb-doped fiber MOPA system incorporating temporal shaping.

We report an Yb-doped fiber master-oscillator power-amplifier (MOPA) system with the capability of selectively generating doughnut-shaped radially and azimuthally polarized beams with user-defined temporal pulse shapes. The desired output polarization was generated with the aid of a nanograting spatially variant half-waveplate (S-waveplate). The latter was used to convert the linearly polarized fundamental (LP01) mode output from the preamplification stages to a doughnut-shaped radially polarized beam prior to the power amplifier stage. A maximum output pulse energy of ∼860 µJ was achieved for ∼100 ns pulses at 25 kHz with user-defined pulse shape for both radial and azimuthal polarization states. The polarization purity and beam propagation factor (M2) were measured to be >12 dB and 2.2, respectively.

Low-loss Kagome hollow-core fibers operating from the near- to the mid-IR.

We report the fabrication and characterization of Kagome hollow-core antiresonant fibers, which combine low attenuation (as measured at ∼30 cm bend diameter) with a wide operating bandwidth and high modal purity. Record low attenuation values are reported: 12.3 dB/km, 13.9 dB/km, and 9.6 dB/km in three different fibers optimized for operation at 1 µm, 1.55 µm, and 2.5 µm, respectively. These fibers are excellent candidates for ultra-high power delivery at key laser wavelengths including 1.064 µm and 2.94 µm, as well as for applications in gas-based sensing and nonlinear optics.

Optoelectronic oscillator incorporating hollow-core photonic bandgap fiber.

We demonstrate, to the best of our knowledge, the first optoelectronic oscillator that uses hollow-core photonic bandgap fiber (HC-PBGF) as a delay element of a sufficient length to allow for low-noise operation. We show experimentally that HC-PBGF can improve the temperature stability of the oscillator by a factor of more than 15, as compared to standard optical fiber. We also measured the oscillator's phase noise, allowing evaluation of the suitability of HC-PBGF for this application. Additionally, this Letter also provides, to the best of our knowledge, the first characterization of the temperature stability of a long length (>800 m in our Letter) of low-thermal sensitivity (2 ps/km/K) HC-PBGF wound on a spool.

Optimisation of amplitude limiters for phase preservation based on the exact solution to degenerate four-wave mixing.

Adopting an exact solution to four-wave mixing (FWM), wherein harmonic evolution is described by the sum of two Bessel functions, we identify two causes of amplitude to phase noise conversion which impair FWM saturation based amplitude regenerators: self-phase modulation (SPM) and Bessel-order mixing (BOM). By increasing the pump to signal power ratio, we may arbitrarily reduce their impact, realising a phase preserving amplitude regenerator. We demonstrate the technique by applying it to the regeneration of a 10 GBaud QPSK signal, achieving a high level of amplitude squeezing with minimal amplitude to phase noise conversion.

Inter-modal four-wave mixing study in a two-mode fiber.

We demonstrate efficient four-wave mixing among different spatial modes in a 1-km long two-mode fiber at telecommunication wavelengths. Two pumps excite the LP01 and LP11 modes, respectively, while the probe signal excites the LP01 mode, and the phase conjugation (PC) and Bragg scattering (BS) idlers are generated in the LP11 mode. For these processes we experimentally characterize their phase matching efficiency and bandwidth and find that they depend critically on the wavelength separation of the two pumps, in good agreement with the numerical study we carried out. We also confirm experimentally that BS has a larger bandwidth than PC for the optimum choice of the pump wavelength separation.

Exploiting the short wavelength gain of silica-based thulium-doped fiber amplifiers.

Short wavelength operation (1650-1800 nm) of silica-based thulium-doped fiber amplifiers (TDFAs) is investigated. We report the first demonstration of in-band diode-pumped silica-based TDFAs working in the 1700-1800 nm waveband. Up to 29 dB of small-signal gain is achieved in this spectral region, with an operation wavelength accessible by diode pumping as short as 1710 nm. Further gain extension toward shorter wavelengths is realized in a fiber laser pumped configuration. A silica-based TDFA working in the 1650-1700 nm range with up to 29 dB small-signal gain and noise figure as low as 6.5 dB is presented.

New optical fibres for high-capacity optical communications.

Researchers are within a factor of 2 or so from realizing the maximum practical transmission capacity of conventional single-mode fibre transmission technology. It is therefore timely to consider new technological approaches offering the potential for more cost-effective scaling of network capacity than simply installing more and more conventional single-mode systems in parallel. In this paper, I review physical layer options that can be considered to address this requirement including the potential for reduction in both fibre loss and nonlinearity for single-mode fibres, the development of ultra-broadband fibre amplifiers and finally the use of space division multiplexing.

MicroStructure Element Method (MSEM): viscous flow model for the virtual draw of microstructured optical fibers.

We propose a new method to accurately model the structural evolution of a microstructured fiber (MOF) during its drawing process, given its initial preform structure and draw conditions. The method, applicable to a broad range of MOFs with high air-filling fraction and thin glass membranes, is an extension of the Discrete Element Method; it determines forces on the nodes in the microstructure to progressively update their position along the neck-down region, until the fiber reaches a final frozen state. The model is validated through simulation of 6 Hollow Core Photonic Band Gap Fibers (HC-PBGFs) and is shown to predict accurately the final fiber dimensions and cross-sectional distortions. The model is vastly more capable than other state of the art models and allows fast exploration of wide drawing parameter spaces, eliminating the need for expensive and time-consuming empirical parameter scans.

Accurate calibration of S(2) and interferometry based multimode fiber characterization techniques.

We present a novel method to validate the relative amount of power carried by high order modes in a multimode fiber using a Spatial and Spectral (S(2)) imaging technique. The method can be utilized to calibrate the S(2) set-up and uses Fresnel reflections from a thin glass plate to compare theoretical values with experimental results. We have found that, in the most general case, spectral leakage and sampling errors can lead S(2) to underestimate the multipath interference (MPI) of high order modes by several decibels, thus significantly impairing the result of the measurement. On the other hand, by applying suitable corrections as described in this work, we demonstrate that the S(2) produces MPI estimates that are accurate to within 1dB or better.

Optical side scattering radiometry for high resolution, wide dynamic range longitudinal assessment of optical fibers.

Current optical reflectometric techniques used to characterize optical fibers have to trade-off longitudinal range with spatial resolution and therefore struggle to provide simultaneously wide dynamic range (>20dB) and high resolution (<10cm). In this work, we develop and present a technique we refer to as Optical Side Scattering Radiometry (OSSR) capable of resolving discrete and distributed scattering properties of fibers along their length with up to 60dB dynamic range and 5cm spatial resolution. Our setup is first validated on a standard single mode telecoms fiber. Then we apply it to a record-length 11km hollow core photonic band-gap fiber (HC-PBGF) the characterization requirements of which lie far beyond the capability of standard optical reflectometric instruments. We next demonstrate use of the technique to investigate and explain the unusually high loss observed in another HC-PBGF and finally demonstrate its flexibility by measuring a HC-PBGF operating at a wavelength of 2µm. In all of these examples, good agreement between the OSSR measurements and other well-established (but more limited) characterization methods, i.e. cutback loss and OTDR, was obtained.