Spray deposition of highly transparent, low-resistance networks of silver nanowires over large areas.

A method to produce scalable, low-resistance, high-transparency, percolating networks of silver nanowires by spray coating is presented. By optimizing the spraying parameters, networks with a sheet resistance of R(s) ≈ 50 Ω â–¡(-1) at a transparency of T = 90% can be produced. The critical processing parameter is shown to be the spraying pressure. Optimizing the pressure reduces the droplet size resulting in more uniform networks. High uniformity leads to a low percolation exponent, which is essential for low-resistance, high-transparency films.

Anisotropic Silver Nanomaterials by Photochemical Reactions: Synthesis and Applications.

Silver-based nanoparticles have attracted a broad interest due to their outstanding optical and chemical properties and have been studied for applications in many fields. While different synthetic routes have been explored, photochemical synthesis has attracted a special interest for its limited use of chemicals and ease of control over the shape and size of the nanoparticles. This paper reviews the main factors affecting the synthesis of anisotropic silver nanoparticles, such as irradiation wavelength, pH, etc., and the role of specific key molecules, such as citrate. The paper is structured into different sections depending on how the synthesis is initiated; thus, after the introduction, the photochemical conversion reaction starting from nanoparticles, or seeds, obtained chemically, is covered, followed by reactions from nanoparticles obtained by laser ablation by seedless reactions. After that, the applications proposed for anisotropic nanoparticles obtained by the methods discussed in the previous sections are briefly covered and, finally, the conclusions and the author's perspectives are given.

Raman spectroscopy data related to the laser induced reduction of graphene oxide.

This data paper reports data obtained from the fitting of Raman spectra obtained during a laser reduction process for graphene oxide under different processing and material conditions. In particular, we show examples of fitting curves of three different representative reduced graphene oxide spectra, as well as fitting curves for a graphene oxide spectrum. Moreover, we show and compare cumulative distributions of the ID/IG values (intensity ratio of peaks D and G) obtained from spectra acquired from different samples. Fittings and distributions were obtained using the OriginPro 8.5 software package. Such data may be the starting point of further experiments on the laser induced reduction of graphene oxide.

Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications.

Laser synthesis emerges as a suitable technique to produce ligand-free nanoparticles, alloys and functionalized nanomaterials for catalysis, imaging, biomedicine, energy and environmental applications. In the last decade, laser ablation and nanoparticle generation in liquids has proven to be a unique and efficient technique to generate, excite, fragment and conjugate a large variety of nanostructures in a scalable and clean way. In this work, we give an overview on the fundamentals of pulsed laser synthesis of nanocolloids and new information about its scalability towards selected applications. Biomedicine, catalysis and sensing are the application areas mainly discussed in this review, highlighting advantages of laser-synthesized nanoparticles for these types of applications and, once partially resolved, the limitations to the technique for large-scale applications.

Optical data related to Ag nanoplates utilized for plasmon sensing.

In this data paper we share the absorption spectrum of Ag NP ablated in pure water and in presence of trisodium citrate (TSC). We also share the full emission spectrum of the irradiation lamp used for the reshaping process described in the related research paper. The data is related to the research article "Plasmon Sensing and enhancement of laser prepared silver colloids" [1].

Transparent, flexible, and highly conductive thin films based on polymer-nanotube composites.

We have prepared flexible, transparent, and very conducting thin composite films from poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate), filled with both arc discharge and HIPCO single-walled nanotubes, at high loading level. The films are of high optical uniformity. The arc discharge nanotube-filled composites were significantly more conductive, demonstrating DC conductivities of >10(5) S/m for mass fractions >50 wt %. The ratio of DC to optical conductivity was higher for composites with mass fractions of 55-60 wt % than for nanotube-only films. For an 80 nm thick composite, filled with 60 wt % arc discharge nanotubes, this conductivity ratio was maximized at sigma(DC)/sigma(Op) = 15. This translates into transmittance (550 nm) and sheet resistance of 75 and 80 Omega/square, respectively. These composites were electromechanically very stable, showing <1% resistance change over 130 bend cycles.

High-yield production of graphene by liquid-phase exfoliation of graphite.

Fully exploiting the properties of graphene will require a method for the mass production of this remarkable material. Two main routes are possible: large-scale growth or large-scale exfoliation. Here, we demonstrate graphene dispersions with concentrations up to approximately 0.01 mg ml(-1), produced by dispersion and exfoliation of graphite in organic solvents such as N-methyl-pyrrolidone. This is possible because the energy required to exfoliate graphene is balanced by the solvent-graphene interaction for solvents whose surface energies match that of graphene. We confirm the presence of individual graphene sheets by Raman spectroscopy, transmission electron microscopy and electron diffraction. Our method results in a monolayer yield of approximately 1 wt%, which could potentially be improved to 7-12 wt% with further processing. The absence of defects or oxides is confirmed by X-ray photoelectron, infrared and Raman spectroscopies. We are able to produce semi-transparent conducting films and conducting composites. Solution processing of graphene opens up a range of potential large-area applications, from device and sensor fabrication to liquid-phase chemistry.

Catalytic chemical vapor deposition of single-wall carbon nanotubes at low temperatures.

We report surface-bound growth of single-wall carbon nanotubes (SWNTs) at temperatures as low as 350 degrees C by catalytic chemical vapor deposition from undiluted C2H2. NH3 or H2 exposure critically facilitates the nanostructuring and activation of sub-nanometer Fe and Al/Fe/Al multilayer catalyst films prior to growth, enabling the SWNT nucleation at lower temperatures. We suggest that carbon nanotube growth is governed by the catalyst surface without the necessity of catalyst liquefaction.