Low-temperature synthesis and electrocatalytic application of large-area PtTe2 thin films.

The synthesis of transition metal dichalcogenides (TMDs) has been a primary focus for 2D nanomaterial research over the last 10 years, however, only a small fraction of this research has been concentrated on transition metal ditellurides. In particular, nanoscale platinum ditelluride (PtTe2) has rarely been investigated, despite its potential applications in catalysis, photonics and spintronics. Of the reports published, the majority examine mechanically-exfoliated flakes from chemical vapor transport (CVT) grown crystals. This method produces high quality-crystals, ideal for fundamental studies. However, it is very resource intensive and difficult to scale up meaning there are significant obstacles to implementation in large-scale applications. In this report, the synthesis of thin films of PtTe2 through the reaction of solid-phase precursor films is described. This offers a production method for large-area, thickness-controlled PtTe2, potentially suitable for a number of applications. These polycrystalline PtTe2 films were grown at temperatures as low as 450 °C, significantly below the typical temperatures used in the CVT synthesis methods. Adjusting the growth parameters allowed the surface coverage and morphology of the films to be controlled. Analysis with scanning electron- and scanning tunneling microscopy indicated grain sizes of above 1 µm could be achieved, comparing favorably with typical values of ∼50 nm for polycrystalline films. To investigate their potential applicability, these films were examined as electrocatalysts for the hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR). The films showed promising catalytic behavior, however, the PtTe2 was found to undergo chemical transformation to a substoichiometric chalcogenide compound under ORR conditions. This study shows while PtTe2 is stable and highly useful for in HER, this property does not apply to ORR, which undergoes a fundamentally different mechanism. This study broadens our knowledge on the electrocatalysis of TMDs.

A photochemical approach for a fast and self-limited covalent modification of surface supported graphene with photoactive dyes.

Herein, we report a simple method for a covalent modification of surface supported graphene with photoactive dyes. Graphene was fabricated on cubic-SiC/Si(001) wafers due to their low cost and suitability for mass-production of continuous graphene fit for electronic applications on millimetre scale. Functionalisation of the graphene surface was carried out in solution via white light induced photochemical generation of phenazine radicals from phenazine diazonium salt. The resulting covalently bonded phenazine-graphene hybrid structure was characterised by scanning tunnelling microscopy (STM) and spectroscopy (STS), Raman spectroscopy and density functional theory (DFT) calculations. It was found that phenazine molecules form an overlayer, which exhibit a short range order with a rectangular unit cell on the graphene surface. DFT calculations based on STM results reveal that molecules are standing up in the overlayer with the maximum coverage of 0.25 molecules per graphene unit cell. Raman spectroscopy and STM results show that the growth is limited to one monolayer of standing molecules. STS reveals that the phenazine-graphene hybrid structure has a band gap of 0.8 eV.

Nanopatterning and Electrical Tuning of MoS2 Layers with a Subnanometer Helium Ion Beam.

We report subnanometer modification enabled by an ultrafine helium ion beam. By adjusting ion dose and the beam profile, structural defects were controllably introduced in a few-layer molybdenum disulfide (MoS2) sample and its stoichiometry was modified by preferential sputtering of sulfur at a few-nanometer scale. Localized tuning of the resistivity of MoS2 was demonstrated and semiconducting, metallic-like, or insulating material was obtained by irradiation with different doses of He(+). Amorphous MoSx with metallic behavior has been demonstrated for the first time. Fabrication of MoS2 nanostructures with 7 nm dimensions and pristine crystal structure was also achieved. The damage at the edges of these nanostructures was typically confined to within 1 nm. Nanoribbons with widths as small as 1 nm were reproducibly fabricated. This nanoscale modification technique is a generalized approach that can be applied to various two-dimensional (2D) materials to produce a new range of 2D metamaterials.

Optical characterisation of plasmonic nanostructures on planar substrates using second-harmonic generation.

Off-normal, polarization dependent second-harmonic generation (SHG) measurements were performed ex situ on plasmonic nanostructures grown by self-assembly on nanopatterned templates. These exploratory studies of Ag nanoparticle (NP) arrays show that the sensitivity of SHG to the local fields, which are modified by the NP size, shape and distribution, makes it a promising fixed wavelength characterization technique that avoids the complexity of spectroscopic SHG. The off-normal geometry provides access to the out-of-plane SH response, which is typically an order-of-magnitude larger than the in-surface-plane response measured using normal incidence, for example in SHG microscopy. By choosing the plane of incidence orthogonal to the NP array direction, it was shown that the p-polarized SH response, as a function of input polarization, is very sensitive to NP morphology, with a change of 20% in the aspect ratio of the NPs producing a variation of a factor of 30 in the easily measureable ratio of the p-polarized SH field strength for s- and p-polarized input. The results show that such a fixed geometry could be used for the in situ characterization of anisotropic nanostructure morphology during growth by self-assembly, which could be particularly useful in situations where rotating the sample may be neither desirable nor easily accomplished.

Rotated domain network in graphene on cubic-SiC(001).

The atomic structure of the cubic-SiC(001) surface during ultra-high vacuum graphene synthesis has been studied using scanning tunneling microscopy (STM) and low-energy electron diffraction. Atomically resolved STM studies prove the synthesis of a uniform, millimeter-scale graphene overlayer consisting of nanodomains rotated by ±13.5° relative to the left angle bracket 110 right angle bracket-directed boundaries. The preferential directions of the domain boundaries coincide with the directions of carbon atomic chains on the SiC(001)-c(2 × 2) reconstruction, fabricated prior to graphene synthesis. The presented data show the correlation between the atomic structures of the SiC(001)-c(2 × 2) surface and the graphene/SiC(001) rotated domain network and pave the way for optimizing large-area graphene synthesis on low-cost cubic-SiC(001)/Si(001) wafers.

Examining the Desirable Properties of ZnSnO y by Annealing Treatment with a Real-Time Observation of Resistivity.

In this report, 38 nm-thick amorphous zinc-tin oxide (a-ZTO) films were deposited by radio frequency magnetron cosputtering. a-ZTO films were annealed by in situ monitoring of the sheet resistance improvements during the annealing process. A sharp drop in the slope of the sheet resistance curve was observed. The activation energies for the sheet resistance slope were calculated. The activation energy of the reaction for a sharp drop in the slope is much higher than the activation energy for the rest of the slope. Based on the activation energy values, six annealing temperatures were selected to saturate the highest conductivity at lower annealing temperatures and to identify the effects associated with annealing time. We found a direct correlation between annealing temperatures and the duration of the annealing treatment. a-ZTO films with a high conductivity of 320 S/cm were achieved by annealing at a temperature of 220 °C. It is noteworthy that the annealing temperature of 220 °C has clearly replaced the temperature of 300 °C. An irreversible decrease in resistivity was observed for all films. The conduction mechanism of films before and after annealing was determined. We confirm that all films individually exhibit semiconducting and metallic behaviors in the conduction mechanism before and after the lowest resistivity saturation.

Variation in the Bandgap of Amorphous Zinc Tin Oxide: Investigating the Thickness Dependence via In Situ STS.

Amorphous transparent conducting oxides (a-TCOs) have seen substantial interest in recent years due to the significant benefits that they can bring to transparent electronic devices. One such material of promise is amorphous ZnxSn1-xOy (a-ZTO). a-ZTO possesses many attractive properties for a TCO such as high transparency in the visible range, tunable charge carrier concentration, electron mobility, and only being composed of common and abundant elements. In this work, we employ a combination of UV-vis spectrophotometry, X-ray photoemission spectroscopy, and in situ scanning tunneling spectroscopy to investigate a 0.33 eV blue shift in the optical bandgap of a-ZTO, which we conclude to be due to quantum confinement effects.

Miniaturized spectrometer with intrinsic long-term image memory.

Miniaturized spectrometers have great potential for use in portable optoelectronics and wearable sensors. However, current strategies for miniaturization rely on von Neumann architectures, which separate the spectral sensing, storage, and processing modules spatially, resulting in high energy consumption and limited processing speeds due to the storage-wall problem. Here, we present a miniaturized spectrometer that utilizes a single SnS2/ReSe2 van der Waals heterostructure, providing photodetection, spectrum reconstruction, spectral imaging, long-term image memory, and signal processing capabilities. Interface trap states are found to induce a gate-tunable and wavelength-dependent photogating effect and a non-volatile optoelectronic memory effect. Our approach achieves a footprint of 19 µm, a bandwidth from 400 to 800 nm, a spectral resolution of 5 nm, and a > 104 s long-term image memory. Our single-detector computational spectrometer represents a path beyond von Neumann architectures.

The topological soliton in Peierls semimetal Sb.

Sb is a three-dimensional Peierls insulator. The Peierls instability gives rise to doubling of the translational period along the [111] direction and alternating van der Waals and covalent bonding between (111) atomic planes. At the (111) surface of Sb, the Peierls condition is violated, which in theory can give rise to properties differing from the bulk. The atomic and electronic structure of the (111) surface of Sb have been simulated by density functional theory calculations. We have considered the two possible (111) surfaces, containing van der Waals dangling bonds or containing covalent dangling bonds. In the models, the surfaces are infinite and the structure is defect free. Structural optimization of the model containing covalent dangling bonds results in strong deformation, which is well described by a topological soliton within the Su-Schrieffer-Heeger model centered about 25 Å below the surface. The electronic states associated with the soliton see an increase in the density of states (DOS) at the Fermi level by around an order of magnitude at the soliton center. Scanning tunneling microscopy and spectroscopy (STM/STS) measurements reveal two distinct surface regions, indicating that there are different surface regions cleaving van der Waals and covalent bonds. The DFT is in good agreement with the STM/STS experiments.

Ultraviolet irradiation-controlled memory effect in graphene field-effect transistors.

Control of graphene memory devices using photons, via control of the charge-transfer process, is demonstrated by employing gate-voltage pulses to program/erase the memory elements. The hysteresis in the conductance-gate voltage-dependence of graphene field-effect transistors on a SiO2 substrate can be greatly enlarged by ultraviolet irradiation in both air and vacuum. An enhanced charge transfer between graphene and its surroundings, induced by ultraviolet illumination, is proposed.

High-rate iron sulfide and sulfur-coupled autotrophic denitrification system: Nutrients removal performance and microbial characterization.

Iron sulfides-based autotrophic denitrification (IAD) is a promising technology for nitrate and phosphate removal from low C:N ratio wastewater due to its cost-effectiveness and low sludge production. However, the slow kinetics of IAD, compared to other sulfur-based autotrophic denitrification (SAD) processes, limits its engineering application. This study constructed a co-electron-donor (FeS and S0 with a volume ratio of 2:1) iron sulfur autotrophic denitrification (ISAD) biofilter and operated at as short as 1 hr hydraulic retention time (HRT). Long-term operation results showed that the superior total nitrogen and phosphate removals of the ISAD biofilter were 90-100% at 1-12 h HRT, with the highest denitrification rate up to 960 mg/L/d. Considering low sulfate production, HRT of 3 h could be the optimal condition. Such superior performance in the ISAD biofilter was achieved due to the interactions between FeS and S0, which accelerated the denitrification process and maintained the acidity-alkalinity balance. Metagenomic analysis found that the enriched nitrate-dependent iron-oxidizing (NDFO) bacteria (Acinetobacter and Acidovorax), sulfur-oxidizing bacteria (SOB), and dissimilatory nitrate reduction to ammonia (DNRA) bacteria likely supported stable nitrate reduction. The metabolic pathway analysis showed that completely denitrification and DNRA, coupled with sulfur oxidation, disproportionation, iron oxidation and phosphate precipitation with FeS and S0 as co-electron donors, were responsible for the high-rate nitrate and phosphate removal. This study provides the potential of ISAD as a highly efficient post-denitrification technology and sheds light on the balanced microbial S-N-Fe transformation.

Effect of Rapid Thermal Annealing on Si-Based Dielectric Films Grown by ICP-CVD.

Silicon nitride, silicon oxide, and silicon oxynitride thin films were deposited on the Si substrate by inductively coupled plasma chemical vapor deposition and annealed at 1100 °C for 3 min in an Ar environment. Silicon nitride and silicon oxide films deposited at ratios of the reactant flow rates of SiH4/N2 = 1.875 and SiH4/N2O = 3, respectively, were Si-rich, while Si excess for the oxynitride film (SiH4/N2/N2O = 3:2:2) was not found. Annealing resulted in a thickness decrease and structural transformation for SiOx and SiNx films. Nanocrystalline phases of Si as well as α- and ß-Si3N4 were found in the annealed silicon nitride film. Compared to oxide and nitride films, the oxynitride film is the least susceptible to change during annealing. The relationship between the structure, composition, and optical properties of the Si-based films has been revealed. It has been shown that the calculated optical parameters (refractive index, extinction coefficient) reflect structural peculiarities of the as-deposited and annealed films.

Nitrate removal in iron sulfide-driven autotrophic denitrification biofilter: Biochemical and chemical transformation pathways and its underlying microbial mechanism.

Iron sulfides-based autotrophic denitrification (IAD) is effective for treating nitrate-contaminated wastewater. However, the complex nitrate transformation pathways coupled with sulfur and iron cycles in IADs are still unclear. In this study, two columns (abiotic vs biotic) with iron sulfides (FeS) as the packing materials were constructed and operated continuously. In the abiotic column, FeS chemically reduced nitrate to ammonium under the ambient condition; this chemical reduction reaction pathway was spontaneous and has been overlooked in IAD reactors. In the biotic column (IAD biofilter), the complex nitrogen-transformation network was composed of chemical reduction, autotrophic denitrification, dissimilatory nitrate reduction to ammonium (DNRA) and sulfate reducing ammonium oxidation (Sulfammox). Metagenomic analysis and XPS characterization of the IAD biofilter further validated the roles of functional microbial communities (e.g., Acidovorax, Diaphorobacter, Desulfuromonas) in nitrate reduction process coupled with iron and sulfur cycles. This study gives an in-depth insight into the nitrogen transformations in IAD system and provides fundamental evidence about the underlying microbial mechanism for its further application in biological nitrogen removal.

Terbium-doped carbon dots (Tb-CDs) as a novel contrast agent for efficient X-ray attenuation.

Metal-doped carbon dots have attracted considerable attention in nanomedicine over the last decade owing to their high biocompatibility and great potential for bioimaging, photothermal therapy, and photodynamic therapy. In this study, we prepared, and for the first time, examined terbium-doped CDs (Tb-CDs) as a novel contrast agent for computed tomography. A detailed physicochemical analysis revealed that the prepared Tb-CDs have small sizes (∼2-3 nm), contain relatively high terbium concentration (∼13.3 wt%), and exhibit excellent aqueous colloidal stability. Furthermore, preliminary cell viability and CT measurements suggested that Tb-CDs exhibit negligible cytotoxicity toward L-929 cells and demonstrate high X-ray absorption performance (∼48.2 ± 3.9 HU L g-1). Based on these findings, the prepared Tb-CDs could serve as a promising contrast agent for efficient X-ray attenuation.

An In Situ Study of Precursor Decomposition via Refractive Index Sensing in p-Type Transparent Copper Chromium Oxide.

Oxide semiconductors are penetrating into a wide range of energy, environmental, and electronic applications, possessing a potential to outrun currently employed semiconductors. However, an insufficient development of p-type oxides is a major obstacle against complete oxide electronics. Quite often oxide deposition is performed by the spray pyrolysis method, inexpensive to implement and therefore accessible to a large number of laboratories. Although, the complex growth chemistry and a lack of in situ monitoring during the synthesis process can complicate the growth optimization of multicomponent oxides. Here we present a concept of plasmonic, optical sensing that has been applied to spray pyrolysis oxide film growth monitoring for the first time. The proposed method utilizes a polarization based refractive index sensing platform using Au nanodimers as transducing elements. As a proof of concept, the changes in the refractive index of the grown film were extracted from individual Cu(acac)2 and Cr(acac)3 precursors in real time to reveal their thermal decomposition processes. Obtained activation energies give insight into the physical origin of the narrow temperature window for the synthesis of high performing p-type transparent conducting copper chromium oxide Cu x CrO2. The versatility of the proposed method makes it effective in the growth rate monitoring of various oxides, exploring new candidate materials and optimizing the synthesis conditions for acquisition of high performing oxides synthesized by a high throughput cost-effective method.

Role of iron(II) sulfide in autotrophic denitrification under tetracycline stress: Substrate and detoxification effect.

Autotrophic denitrification using inorganic compounds as electron donors has gained increasing attention in the field of wastewater treatment due to its numerous advantages, such as no need for exogenous organic carbon, low energy input, and low sludge production. Tetracycline (TC), a refractory contaminant, is often found coexisting with nutrients (NO3- and PO43-) in wastewater, which can negatively affect the biological nutrient removal process because of its biological toxicity. However, the performance of autotrophic denitrification under TC stress has rarely been reported. In this study, the effects of TC on autotrophic denitrification with thiosulfate (Na2S2O3) and iron (II) sulfide (FeS) as the electron donors were investigated. With Na2S2O3 as the electron donor, TC slowed down the nitrate removal rate, which decreased from 1.32 to 0.18 d-1, when TC concentration increased from 0 mg/L to 50 mg/L. When TC concentration was higher than 2 mg/L, nitrite reduction was seriously inhibited, leading to nitrite accumulation. With FeS as the electron donor, nitrate removal was much more efficient under TC-stressed conditions, and no distinct nitrite accumulation was observed when the initial TC concentration was as high as 10 mg/L, indicating the effective detoxification of FeS. The detoxification effects in the FeS autotrophic denitrification system mainly resulted from the rapid adsorption of TC by FeS and effective degradation of TC, as proven by a relatively higher living biomass area. This study offers new insights into the response of sulfur-based autotrophic denitrifiers to TC stress and demonstrates that the FeS-based autotrophic denitrification process is a promising technology for the treatment of wastewater containing emerging contaminants and nutrients.

The influence of drinking water constituents on the level of microplastic release from plastic kettles.

Microplastic (MP) release from household plastic products has become a global concern due to the high recorded levels of microplastic and the direct risk of human exposure. However, the most widely used MP measurement protocol, which involves the use of deionized (DI) water, fails to account for the ions and particles present in real drinking water. In this paper, the influence of typical ions (Ca2+/HCO3-, Fe3+, Cu2+) and particles (Fe2O3 particles) on MP release was systematically investigated by conducting a 100-day study using plastic kettles. Surprisingly, after 40 days, all ions resulted in a greater than 89.0% reduction in MP release while Fe2O3 particles showed no significant effect compared to the DI water control. The MP reduction efficiency ranking is Fe3+ ≈ Cu2+ > Ca2+/HCO3- > > Fe2O3 particles ≈ DI water. Physical and chemical characterization using SEM-EDX, AFM, XPS and Raman spectroscopy confirmed Ca2+/HCO3-, Cu2+ and Fe3+ ions are transformed into passivating films of CaCO3, CuO, and Fe2O3, respectively, which are barriers to MP release. In contrast, there was no film formed when the plastic was exposed to Fe2O3 particles. Studies also confirmed that films with different chemical compositions form naturally in kettles during real life due to the different ions present in local regional water supplies. All films identified in this study can substantially reduce the levels of MP release while withstanding the repeated adverse conditions associated with daily use. This study underscores the potential for regional variations in human MP exposure due to the substantial impact water constituents have on the formation of passivating film formation and the subsequent release of MPs.

4D printing of MXene hydrogels for high-efficiency pseudocapacitive energy storage.

2D material hydrogels have recently sparked tremendous interest owing to their potential in diverse applications. However, research on the emerging 2D MXene hydrogels is still in its infancy. Herein, we show a universal 4D printing technology for manufacturing MXene hydrogels with customizable geometries, which suits a family of MXenes such as Nb2CTx, Ti3C2Tx, and Mo2Ti2C3Tx. The obtained MXene hydrogels offer 3D porous architectures, large specific surface areas, high electrical conductivities, and satisfying mechanical properties. Consequently, ultrahigh capacitance (3.32 F cm-2 (10 mV s-1) and 233 F g-1 (10 V s-1)) and mass loading/thickness-independent rate capabilities are achieved. The further 4D-printed Ti3C2Tx hydrogel micro-supercapacitors showcase great low-temperature tolerance (down to -20 °C) and deliver high energy and power densities up to 93 µWh cm-2 and 7 mW cm-2, respectively, surpassing most state-of-the-art devices. This work brings new insights into MXene hydrogel manufacturing and expands the range of their potential applications.

VOx Phase Mixture of Reduced Single Crystalline V2O5: VO2 Resistive Switching.

The strongly correlated electron material, vanadium dioxide (VO2), has seen considerable attention and research application in metal-oxide electronics due to its metal-to-insulator transition close to room temperature. Vacuum annealing a V2O5(010) single crystal results in Wadsley phases (VnO2n+1, n > 1) and VO2. The resistance changes by a factor of 20 at 342 K, corresponding to the metal-to-insulator phase transition of VO2. Macroscopic voltage-current measurements with a probe separation on the millimetre scale result in Joule heating-induced resistive switching at extremely low voltages of under a volt. This can reduce the hysteresis and facilitate low temperature operation of VO2 devices, of potential benefit for switching speed and device stability. This is correlated to the low resistance of the system at temperatures below the transition. High-resolution transmission electron microscopy measurements reveal a complex structural relationship between V2O5, VO2 and V6O13 crystallites. Percolation paths incorporating both VO2 and metallic V6O13 are revealed, which can reduce the resistance below the transition and result in exceptionally low voltage resistive switching.

Probing one antiferromagnetic antiphase boundary and single magnetite domain using nanogap contacts.

We have probed one antiferromagnetic (AF) antiphase boundary (APB) and a single Fe(3)O(4) domain using nanogap contacts. Our experiments directly demonstrate that, in the case of probing one AF-APB, a large magnetoresistance (MR), high resistivity, and a high saturation field are observed as compared with the case of probing a single Fe(3)O(4) domain. The shape of the temperature-dependent MR curves is also found to differ between the single domain and one of the AF-APB measurements, with a characteristic strong temperature dependence for the single domain and temperature independence for the one AF-APB case. We argue that these observations are indicative of profound changes in the electronic transport across APBs. The investigated APB defects increase the activation energy and disturb the long-range charge ordering of monodomain Fe(3)O(4).