Molten Salt-Promoted MgO Adsorbents for CO2 Capture: Transient Kinetic Studies.

Optimization of MgO adsorbents is predominantly focused on the regulation of appropriate adsorption sites for CO2 associated with Mg2+-O2- sites of low coordination. Here, for the first time, we conducted transient kinetic experiments to identify and characterize changes of the CO2 molecular path in MgO-based CO2 adsorbents upon the addition of molten salt modifiers. Among the optimized samples, addition of 10 mol % NaNO2 on the surface of MgO exhibited the highest CO2 uptake (15.7 mmol g-1) at 350 °C compared to less than 0.1 mmol g-1 for the unpromoted MgO. Kinetic modeling showed that the interaction of molten salt-promoted MgO with CO2 at 300 °C involves three different processes, namely, fast surface adsorption associated with surface-active basic sites, chemical reaction associated with MgCO3 formation, and a slow diffusion step being the rate-limiting step of the carbonation process. Furthermore, transient kinetic studies coupled with mass spectrometry under low CO2 partial pressure agreed well with the kinetic simulation results based on TGA measurements, demonstrating an in-depth understanding of the CO2-capturing performance gained and its considerable significance for future practical designs of precombustion CO2 capture.

Valorization of agricultural wastes could improve soil fertility and mitigate soil direct N2O emissions.

The emerging need for sustainable management of the increasing quantities of urban and industrial organic wastes creates opportunities for the development of alternative strategies for the improvement of degraded soils. The current study was performed to examine the effects of agricultural wastes application on soil bacterial community as well as CO2 and N2O direct gas emissions. Untreated soils were compared with soils, which received the same amount of N (100 µg/g soil) in the form of ammonium nitrate and organic agricultural waste. In particular, soils were incubated with three different organic agricultural wastes, orange (OP), mandarin (MP) and banana peels (BP) and ammonium nitrate (F) after adjusting soil water at 70% of its holding capacity. In the current study, soil chemical characteristics, quantitative PCR of denitrifiers (nirK, nirS, nosZI and nosZII) and16s rRNA amplicon sequencing were assessed to examine the links between the soil microbial communities and short-term soil direct N2O emissions when treated with agricultural wastes. The highest soil direct N2O emissions were recorded in soils received ammonium nitrate while soils received agricultural wastes exhibited substantially lower soil direct N2O emissions. On the contrary, agricultural wastes stimulated CO2 accumulation as well as the growth of copiotrophic bacterial groups like Proteobacteria and Firmicutes. Interestingly, direct soil N2O emissions were decoupled from the density of denitrifier community while agricultural wastes caused a substantial reduction of the relative abundance of bacterial taxa associated with N2O emissions in the soil. This study proves evidence that agricultural wastes could be integrated in a waste management strategy, which inter alia includes their direct use in agricultural ecosystems resulting in reduced N2O emissions.

Evolution of Oxygen Vacancy Sites in Ceria-Based High-Entropy Oxides and Their Role in N2 Activation.

In this work, a relatively new class of materials, rare earth (RE) based high entropy oxides (HEO) are discussed in terms of the evolution of the oxygen vacant sites (Ov) content in their structure as the composition changes from binary to HEO using both experimental and computational tools; the composition of HEO under focus is the CeLaPrSmGdO due to the importance of ceria-related (fluorite) materials to catalysis. To unveil key features of quinary HEO structure, ceria-based binary CePrO and CeLaO compositions as well as SiO2, the latter as representative nonreducible oxide, were used and compared as supports for Ru (6 wt % loading). The role of the Ov in the HEO is highlighted for the ammonia production with particular emphasis on the N2 dissociation step (N2(ads) → Nads) over a HEO; the latter step is considered the rate controlling one in the ammonia production. Density functional theory (DFT) calculations and 18O2 transient isotopic experiments were used to probe the energy of formation, the population, and the easiness of formation for the Ov at 650 and 800 °C, whereas Synchrotron EXAFS, Raman, EPR, and XPS probed the Ce-O chemical environment at different length scales. In particular, it was found that the particular HEO composition eases the Ov formation in bulk, in medium (Raman), and in short (localized) order (EPR); more Ov population was found on the surface of the HEO compared to the binary reference oxide (CePrO). Additionally, HEO gives rise to smaller and less sharp faceted Ru particles, yet in stronger interaction with the HEO support and abundance of Ru-O-Ce entities (Raman and XPS). Ammonia production reaction at 400 °C and in the 10-50 bar range was performed over Ru/HEO, Ru/CePrO, Ru/CeLaO, and Ru/SiO2 catalysts; the Ru/HEO had superior performance at 10 bar compared to the rest of catalysts. The best performing Ru/HEO catalyst was activated under different temperatures (650 vs 800 °C) so to adjust the Ov population with the lower temperature maintaining better performance for the catalyst. DFT calculations showed that the HEO active site for N adsorption involves the Ov site adjacent to the adsorption event.

Decoupling the Chemical and Mechanical Strain Effect on Steering the CO2 Activation over CeO2-Based Oxides: An Experimental and DFT Approach.

Doped ceria-based metal oxides are widely used as supports and stand-alone catalysts in reactions where CO2 is involved. Thus, it is important to understand how to tailor their CO2 adsorption behavior. In this work, steering the CO2 activation behavior of Ce-La-Cu-O ternary oxide surfaces through the combined effect of chemical and mechanical strain was thoroughly examined using both experimental and ab initio modeling approaches. Doping with aliovalent metal cations (La3+ or La3+/Cu2+) and post-synthetic ball milling were considered as the origin of the chemical and mechanical strain of CeO2, respectively. Experimentally, microwave-assisted reflux-prepared Ce-La-Cu-O ternary oxides were imposed into mechanical forces to tune the structure, redox ability, defects, and CO2 surface adsorption properties; the latter were used as key descriptors. The purpose was to decouple the combined effect of the chemical strain (εC) and mechanical strain (εM) on the modification of the Ce-La-Cu-O surface reactivity toward CO2 activation. During the ab initio calculations, the stability (energy of formation, EOvf) of different configurations of oxygen vacant sites (Ov) was assessed under biaxial tensile strain (ε > 0) and compressive strain (ε < 0), whereas the CO2-philicity of the surface was assessed at different levels of the imposed mechanical strain. The EOvf values were found to decrease with increasing tensile strain. The Ce-La-Cu-O(111) surface exhibited the lowest EOvf values for the single subsurface sites, implying that Ov may occur spontaneously upon Cu addition. The mobility of the surface and bulk oxygen anions in the lattice contributing to the Ov population was measured using 16O/18O transient isothermal isotopic exchange experiments; the maximum in the dynamic rate of 16O18O formation, Rmax(16O18O), was 13.1 and 8.5 µmol g-1 s-1 for pristine (chemically strained) and dry ball-milled (chemically and mechanically strained) oxides, respectively. The CO2 activation pathway (redox vs associative) was experimentally probed using in situ diffuse reflectance infrared Fourier transform spectroscopy. It was demonstrated that the mechanical strain increased up to 6 times the CO2 adsorption sites, though reducing their thermal stability. This result supports the mechanical actuation of the "carbonate"-bound species; the latter was in agreement with the density functional theory (DFT)-calculated C-O bond lengths and O-C-O angles. Ab initio studies shed light on the CO2 adsorption energy (Eads), suggesting a covalent bonding which is enhanced in the presence of doping and under tensile strain. Bader charge analysis probed the adsorbate/surface charge distribution and illustrated that CO2 interacts with the dual sites (acidic and basic ones) on the surface, leading to the formation of bidentate carbonate species. Density of states (DOS) studies revealed a significant Eg drop in the presence of double Ov and compressive strain, a finding with design implications in covalent type of interactions. To bridge this study with industrially important catalytic applications, Ni-supported catalysts were prepared using pristine and ball-milled oxides and evaluated for the dry reforming of methane reaction. Ball milling was found to induce modification of the metal-support interface and Ni catalyst reducibility, thus leading to an increase in the CH4 and CO2 conversions. This study opens new possibilities to manipulate the CO2 activation for a portfolio of heterogeneous reactions.

Unravelling the Mechanism of Intermediate-Temperature CO2 Interaction with Molten-NaNO3 -Salt-Promoted MgO.

The optimization of MgO-based adsorbents as advanced CO2 -capture materials is predominantly focused on their molten-salt modification, for which theoretical and experimental contributions provide great insights for their high CO2 -capture performance. The underlying mechanism of the promotion effect of the molten salt on CO2 capture, however, is a topic of controversy. Herein, advanced experimental characterization techniques, including in situ environmental transmission electron microscopy (eTEM) and CO2 chemisorption by diffuse-reflectance infrared Fourier transform spectroscopy (DRIFTS), transient 18 O-isotopic exchange, and density functional theory (DFT), are employed to elucidate the mechanism of the CO2 interaction with molten-salt-modified MgO in the 250-400 °C range. Herein, eTEM studies using low (2-3 mbar) and high (700 mbar) CO2 pressures illustrate the dynamic evolution of the molten NaNO3 salt promoted and unpromoted MgO carbonation with high magnification (<50 nm). The formation of 18 O-NaNO3 (use of 18 O2 ) and C16 O18 O following CO2 interaction, verifies the proposed reaction path: conversion of NO3 - (NO3 -  â†’ NO2 +  + O2- ), adsorption of NO2 + on MgO with significant weakening of CO2 adsorption strength, and formation of [Mg2+ … O2- ] ion pairs preventing the development of an impermeable MgCO3 shell, which largely increases the rate of bulk MgO carbonation.

Design Aspects of Doped CeO2 for Low-Temperature Catalytic CO Oxidation: Transient Kinetics and DFT Approach.

CO elimination through oxidation over highly active and cost-effective catalysts is a way forward for many processes of industrial and environmental importance. In this study, doped CeO2 with transition metals (TM = Cu, Co, Mn, Fe, Ni, Zr, and Zn) at a level of 20 at. % was tested for CO oxidation. The oxides were prepared using microwave-assisted sol-gel synthesis to improve catalyst's performance for the reaction of interest. The effect of heteroatoms on the physicochemical properties (structure, morphology, porosity, and reducibility) of the binary oxides M-Ce-O was meticulously investigated and correlated to their CO oxidation activity. It was found that the catalytic activity (per gram basis or TOF, s-1) follows the order Cu-Ce-O > Ce-Co-O > Ni-Ce-O > Mn-Ce-O > Fe-Ce-O > Ce-Zn-O > CeO2. Participation of mobile lattice oxygen species in the CO/O2 reaction does occur, the extent of which is heteroatom-dependent. For that, state-of-the-art transient isotopic 18O-labeled experiments involving 16O/18O exchange followed by step-gas CO/Ar or CO/O2/Ar switches were used to quantify the contribution of lattice oxygen to the reaction. SSITKA-DRIFTS studies probed the formation of carbonates while validating the Mars-van Krevelen (MvK) mechanism. Scanning transmission electron microscopy-high-angle annular dark field imaging coupled with energy-dispersive spectroscopy proved that the elemental composition of dopants in the individual nanoparticle of ceria is less than their composition at a larger scale, allowing the assessment of the doping efficacy. Despite the similar structural features of the catalysts, a clear difference in the Olattice mobility was also found as well as its participation (as expressed with the α descriptor) in the reaction, following the order αCu > αCo> αMn > αZn. Kinetic studies showed that it is rather the pre-exponential (entropic) factor and not the lowering of activation energy that justifies the order of activity of the solids. DFT calculations showed that the adsorption of CO on the Cu-doped CeO2 surface is more favorable (-16.63 eV), followed by Co, Mn, Zn (-14.46, -4.90, and -4.24 eV, respectively), and pure CeO2 (-0.63 eV). Also, copper compensates almost three times more charge (0.37e-) compared to Co and Mn, ca. 0.13e- and 0.10e-, respectively, corroborating for its tendency to be reduced. Surface analysis (X-ray photoelectron spectroscopy), apart from the oxidation state of the elements, revealed a heteroatom-ceria surface interaction (Oa species) of different extents and of different populations of Oa species.