Long-range order enabled stability in quantum dot light-emitting diodes.

Light-emitting diodes (LEDs) based on perovskite quantum dots (QDs) have produced external quantum efficiencies (EQEs) of more than 25% with narrowband emission1,2, but these LEDs have limited operating lifetimes. We posit that poor long-range ordering in perovskite QD films-variations in dot size, surface ligand density and dot-to-dot stacking-inhibits carrier injection, resulting in inferior operating stability because of the large bias required to produce emission in these LEDs. Here we report a chemical treatment to improve the long-range order of perovskite QD films: the diffraction intensity from the repeating QD units increases three-fold compared with that of controls. We achieve this using a synergistic dual-ligand approach: an iodide-rich agent (aniline hydroiodide) for anion exchange and a chemically reactive agent (bromotrimethylsilane) that produces a strong acid that in situ dissolves smaller QDs to regulate size and more effectively removes less conductive ligands to enable compact, uniform and defect-free films. These films exhibit high conductivity (4 × 10-4 S m-1), which is 2.5-fold higher than that of the control, and represents the highest conductivity recorded so far among perovskite QDs. The high conductivity ensures efficient charge transportation, enabling red perovskite QD-LEDs that generate a luminance of 1,000 cd m-2 at a record-low voltage of 2.8 V. The EQE at this luminance is more than 20%. Furthermore, the stability of the operating device is 100 times better than previous red perovskite LEDs at EQEs of more than 20%.

Distribution control enables efficient reduced-dimensional perovskite LEDs.

Light-emitting diodes (LEDs) based on perovskite quantum dots have shown external quantum efficiencies (EQEs) of over 23% and narrowband emission, but suffer from limited operating stability1. Reduced-dimensional perovskites (RDPs) consisting of quantum wells (QWs) separated by organic intercalating cations show high exciton binding energies and have the potential to increase the stability and the photoluminescence quantum yield2,3. However, until now, RDP-based LEDs have exhibited lower EQEs and inferior colour purities4-6. We posit that the presence of variably confined QWs may contribute to non-radiative recombination losses and broadened emission. Here we report bright RDPs with a more monodispersed QW thickness distribution, achieved through the use of a bifunctional molecular additive that simultaneously controls the RDP polydispersity while passivating the perovskite QW surfaces. We synthesize a fluorinated triphenylphosphine oxide additive that hydrogen bonds with the organic cations, controlling their diffusion during RDP film deposition and suppressing the formation of low-thickness QWs. The phosphine oxide moiety passivates the perovskite grain boundaries via coordination bonding with unsaturated sites, which suppresses defect formation. This results in compact, smooth and uniform RDP thin films with narrowband emission and high photoluminescence quantum yield. This enables LEDs with an EQE of 25.6% with an average of 22.1 ±1.2% over 40 devices, and an operating half-life of two hours at an initial luminance of 7,200 candela per metre squared, indicating tenfold-enhanced operating stability relative to the best-known perovskite LEDs with an EQE exceeding 20%1,4-6.

Polarity-Mediated Antisolvent Control Enables Efficient Lanthanide-Based near-Infrared Perovskite LEDs.

Alloying lanthanide ions (Yb3+) into perovskite quantum dots (Yb3+:CsPb(Cl1-xBrx)3) is an effective method to achieve efficient near-infrared (NIR) luminescence (>950 nm). Increasing the Yb3+ alloying ratio in the perovskite matrix enhances the luminescence intensity of Yb3+ emission at 990 nm. However, high Yb3+ alloying (>15%) results in vacancy-induced inferior material stability. In this work, we developed a polarity-mediated antisolvent manipulation strategy to resolve the incompatibility between a high Yb3+ alloying ratio and inferior stability of Yb3+:CsPb(Cl1-xBrx)3. Precise control of solution polarity enables increased uniformity of the perovskite matrix with fewer trap densities. Employing this strategy, we obtain Yb3+:CsPb(Cl1-xBrx)3 with the highest Yb3+ alloying ratio of 30.2% and a 2-fold higher electroluminescence intensity at 990 nm. We lever the engineered Yb3+:CsPb(Cl1-xBrx)3 to fabricate NIR-LEDs, achieving a peak external quantum efficiency (EQE) of 8.5% at 990 nm: this represents the highest among perovskite NIR-LEDs with an emission wavelength above 950 nm.

Nickel Oxide Hole Injection Layers for Balanced Charge Injection in Quantum Dot Light-Emitting Diodes.

Quantum dot (QD) light-emitting diodes (QLEDs) are promising for next-generation displays, but suffer from carrier imbalance arising from lower hole injection compared to electron injection. A defect engineering strategy is reported to tackle transport limitations in nickel oxide-based inorganic hole-injection layers (HILs) and find that hole injection is able to enhance in high-performance InP QLEDs using the newly designed material. Through optoelectronic simulations, how the electronic properties of NiOx affect hole injection efficiency into an InP QD layer, finding that efficient hole injection depends on lowering the hole injection barrier and enhancing the acceptor density of NiOx is explored. Li doping and oxygen enriching are identified as effective strategies to control intrinsic and extrinsic defects in NiOx, thereby increasing acceptor density, as evidenced by density functional theory calculations and experimental validation. With fine-tuned inorganic HIL, InP QLEDs exhibit a luminance of 45 200 cd m-2 and an external quantum efficiency of 19.9%, surpassing previous inorganic HIL-based QLEDs. This study provides a path to designing inorganic materials for more efficient and sustainable lighting and display technologies.

Ligand-Solvent Coordination Enables Comprehensive Trap Passivation for Efficient Near-Infrared Quantum Dot Light-Emitting Diodes.

Near-infrared light-emitting diodes (NIR LEDs) based on perovskite quantum dots (QDs) have produced external quantum efficiency (EQE) of ~15 %. However, these high-performance NIR-QLEDs suffer from immediate carrier quenching because of the accumulation of migratable ions at the surface of the QDs. These uncoordinated ions and carriers-if not bound to the nanocrystal surface-serve as centers for exciton quenching and device degradation. In this work, we overcome this issue and fabricate high-performance NIR QLEDs by devising a ligand anchoring strategy, which entails dissolving the strong-binding ligand (Guanidine Hydroiodide, GAI) in the mediate-polar solvent. By employing the dye-sensitized device structure (phosphorescent indicator), we demonstrate the elimination of the interface defects. The treated QDs films exhibit an exciton binding energy of 117 meV: this represents a 1.5-fold increase compared to that of the control (74 meV). We report, as a result, the NIR QLEDs with an EQE of 21 % which is a record among NIR perovskite QLEDs. These QLEDs also exhibit a 7-fold higher operational stability than that of the best previously reported NIR QLEDs. Furthermore, we demonstrate that the QDs are compatible with large-area QLEDs: we showcase 900 mm2 QLEDs with EQE approaching 20 %.

Bifunctional Electron-Transporting Agent for Red Colloidal Quantum Dot Light-Emitting Diodes.

Indium phosphide (InP) quantum dots have enabled light-emitting diodes (LEDs) that are heavy-metal-free, narrow in emission linewidth, and physically flexible. However, ZnO/ZnMgO, the electron-transporting layer (ETL) in high-performance red InP/ZnSe/ZnS LEDs, suffers from high defect densities, quenches luminescence when deposited on InP, and induces performance degradation that arises due to trap migration from the ETL to the InP emitting layer. We posited that the formation of Zn2+ traps on the outer ZnS shell, combined with sulfur and oxygen vacancy migration between ZnO/ZnMgO and InP, may account for this issue. We synthesized therefore a bifunctional ETL (CNT2T, 3',3'″,3'″″-(1,3,5-triazine-2,4,6-triyl)tris(([1,1'-biphenyl]-3-carbonitrile)) designed to passivate Zn2+ traps locally and in situ and to prevent vacancy migration between layers: the backbone of the small molecule ETL contains a triazine electron-withdrawing unit to ensure sufficient electron mobility (6 × 10-4 cm2 V-1 s-1), and the star-shaped structure with multiple cyano groups provides effective passivation of the ZnS surface. We report as a result red InP LEDs having an EQE of 15% and a luminance of over 12,000 cd m-2; this represents a record among organic-ETL-based red InP LEDs.

Epithelial lining fluid concentrations of ceftriaxone in children with community-acquired pneumonia.

Ceftriaxone is widely used in children with community-acquired pneumonia. Currently, there are no available data regarding epithelial lining fluid (ELF) concentrations of ceftriaxone in children. Thus, blood and bronchoalveolar lavage fluids samples were collected by using an opportunistic sampling design, then we determined plasma and ELF concentrations in 22 children (0.5-11.7 years), with a total of 36 plasma and 22 ELF samples available for analysis. Ceftriaxone plasma and ELF concentrations ranged from 1.07 to 138.71 mg/L and from 0.61 to 26.69 mg/L, respectively. Ceftriaxone concentration in ELF was 12.18 ± 5.15 (mean ± standard deviation) times higher than that in plasma, ranging from 1.29 to 20.44.

Analysis of enhanced CT imaging signs and clinicopathological prognostic factors in hepatoid adenocarcinoma of stomach patients with radical surgery: a retrospective study.

BACKGROUND: To investigate the association between CT signs and clinicopathological features and disease recurrence in patients with hepatoid adenocarcinoma of stomach (HAS). METHODS: Forty nine HAS patients undergoing radical surgery were retrospectively collected. Association between CT and clinicopathological features and disease recurrence was analyzed. Multivariate logistic model was constructed and evaluated for predicting recurrence by using receiver operating characteristic (ROC) curve. Survival curves between model-defined risk groups was compared using Kaplan-Meier method. RESULTS: 24(49.0%) patients developed disease recurrence. Multivariate logistic analysis results showed elevated serum CEA level, peritumoral fatty space invasion and positive pathological vascular tumor thrombus were independent factors for disease recurrence. Odds ratios were 10.87 (95%CI, 1.14-103.66), 6.83 (95%CI, 1.08-43.08) and 42.67 (95%CI, 3.66-496.85), respectively. The constructed model showed an area under ROC of 0.912 (95%CI,0.825-0.999). The model-defined high-risk group showed poorer overall survival and recurrence-free survival than the low-risk group (both P < 0.001). CONCLUSIONS: Preoperative CT appearance of peritumoral fatty space invasion, elevated serum CEA level, and pathological vascular tumor thrombus indicated poor prognosis of HAS patients.

Iodotrimethylsilane as a Reactive Ligand for Surface Etching and Passivation of Perovskite Nanocrystals toward Efficient Pure-red to Deep-red LEDs.

Resurfacing perovskite nanocrystals (NCs) with tight-binding and conductive ligands to resolve the dynamic ligands-surface interaction is the fundamental issue for their applications in perovskite light-emitting diodes (PeLEDs). Although various types of surface ligands have been proposed, these ligands either exhibit weak Lewis acid/base interactions or need high polar solvents for dissolution and passivation, resulting in a compromise in the efficiency and stability of PeLEDs. Herein, we report a chemically reactive agent (Iodotrimethylsilane, TMIS) to address the trade-off among conductivity, solubility and passivation using all-inorganic CsPbI3 NCs. The liquid TMIS ensures good solubility in non-polar solvents and reacts with oleate ligands and produces in situ HI for surface etching and passivation, enabling strong-binding ligands on the NCs surface. We report, as a result, red PeLEDs with an external quantum efficiency (EQE) of ≈23 %, which is 11.2-fold higher than the control, and is among the highest CsPbI3 PeLEDs. We further demonstrate the universality of this ligand strategy in the pure bromide system (CsPbBr3 ), and report EQE of ≈20 % at 640, 652, and 664 nm. This represents the first demonstration of a chemically reactive ligand strategy that applies to different systems and works effectively in red PeLEDs spanning emission from pure-red to deep-red.

Dipole Engineering through the Orientation of Interface Molecules for Efficient InP Quantum Dot Light-Emitting Diodes.

InP-based quantum dot (QD) light-emitting diodes (QLEDs) provide a heavy-metal-free route to size-tuned LEDs having high efficiency. The stability of QLEDs may be enhanced by replacing organic hole-injection layers (HILs) with inorganic layers. However, inorganic HILs reported to date suffer from inefficient hole injection, the result of their shallow work functions. Here, we investigate the tuning of the work function of nickel oxide (NiOx) HILs using self-assembled molecules (SAMs). Density functional theory simulations and near-edge X-ray absorption fine structure put a particular focus onto the molecular orientation of the SAMs in tuning the work function of the NiOx HIL. We find that orientation plays an even stronger role than does the underlying molecular dipole itself: SAMs having the strongest electron-withdrawing nitro group (NO2), despite having a high intrinsic dipole, show limited work function tuning, something we assign to their orientation parallel to the NiOx surface. We further find that the NO2 group─which delocalizes electrons over the molecule by resonance─induces a deep lowest unoccupied molecular orbital level that accepts electrons from QDs, producing luminescence quenching. In contrast, SAMs containing a trifluoromethyl group exhibit an angled orientation relative to the NiOx surface, better activating hole injection into the active layer without inducing luminescence quenching. We report an external quantum efficiency (EQE) of 18.8%─the highest EQE among inorganic HIL-based QLEDs (including Cd-based QDs)─in InP QLEDs employing inorganic HILs.

Bright and Stable Light-Emitting Diodes Based on Perovskite Quantum Dots in Perovskite Matrix.

Light-emitting diodes (LEDs) based on metal halide perovskite quantum dots (QDs) have achieved impressive external quantum efficiencies; however, the lack of surface protection of QDs, combined with efficiency droop, decreases device operating lifetime at brightnesses of interest. The epitaxial incorporation of QDs within a semiconducting shell provides surface passivation and exciton confinement. Achieving this goal in the case of perovskite QDs remains an unsolved challenge in view of the materials' chemical instability. Here, we report perovskite QDs that remain stable in a thin layer of precursor solution of perovskite, and we use strained QDs as nucleation centers to drive the homogeneous crystallization of a perovskite matrix. Type-I band alignment ensures that the QDs are charge acceptors and radiative emitters. The new materials show suppressed Auger bi-excition recombination and bright luminescence at high excitation (600 W cm-2), whereas control materials exhibit severe bleaching. Primary red LEDs based on the new materials show an external quantum efficiency of 18%, and these retain high performance to brightnesses exceeding 4700 cd m-2. The new materials enable LEDs having an operating half-life of 2400 h at an initial luminance of 100 cd m-2, representing a 100-fold enhancement relative to the best primary red perovskite LEDs.

All-Inorganic Quantum-Dot LEDs Based on a Phase-Stabilized α-CsPbI3 Perovskite.

The all-inorganic nature of CsPbI3 perovskites allows to enhance stability in perovskite devices. Research efforts have led to improved stability of the black phase in CsPbI3 films; however, these strategies-including strain and doping-are based on organic-ligand-capped perovskites, which prevent perovskites from forming the close-packed quantum dot (QD) solids necessary to achieve high charge and thermal transport. We developed an inorganic ligand exchange that leads to CsPbI3 QD films with superior phase stability and increased thermal transport. The atomic-ligand-exchanged QD films, once mechanically coupled, exhibit improved phase stability, and we link this to distributing strain across the film. Operando measurements of the temperature of the LEDs indicate that KI-exchanged QD films exhibit increased thermal transport compared to controls that rely on organic ligands. The LEDs exhibit a maximum EQE of 23 % with an electroluminescence emission centered at 640 nm (FWHM: ≈31 nm). These red LEDs provide an operating half-lifetime of 10 h (luminance of 200 cd m-2 ) and an operating stability that is 6× higher than that of control devices.

Loss of lncRNA MIAT ameliorates proliferation and fibrosis of diabetic nephropathy through reducing E2F3 expression.

Diabetic nephropathy (DN) is a serious kidney disease resulted from diabetes. Dys-regulated proliferation and extracellular matrix (ECM) accumulation in mesangial cells contribute to DN progression. In this study, we tested expression level of MIAT in DN patients and mesangial cells treated by high glucose (HG). Up-regulation of MIAT was observed in DN. Then, functional assays displayed that silence of MIAT by siRNA significantly repressed the proliferation and cycle progression in mesangial cells induced by HG. Meanwhile, we found that collagen IV, fibronectin and TGF-ß1 protein expression was obviously triggered by HG, which could be rescued by loss of MIAT. Then, further assessment indicated that MIAT served as sponge harbouring miR-147a. Moreover, miR-147a was decreased in DN, which exhibited an antagonistic effect of MIAT on modulating mesangial cell proliferation and fibrosis. Moreover, bioinformatics analysis displayed that E2F transcription factor 3 (E2F3) could act as direct target of miR-147a. We demonstrated that E2F3 was greatly increased in DN and the direct binding association between miR-147a and E2F3 was evidenced using luciferase reporter assay. In summary, our data explored the underlying mechanism of DN pathogenesis validated that MIAT induced mesangial cell proliferation and fibrosis via sponging miR-147a and regulating E2F3.

Circularly Polarized Thermally Activated Delayed Fluorescence Emitters in Through-Space Charge Transfer on Asymmetric Spiro Skeletons.

This work describes a strategy to produce circularly polarized thermally activated delayed fluorescence (CP-TADF). A set of two structurally similar organic emitters SFST and SFOT are constructed, whose spiro architectures containing asymmetric donors result in chirality. Upon grafting within the spiro frameworks, the donor and acceptor are fixed proximally in a face-to-face manner. This orientation allows intramolecular through-space charge transfer (TSCT) to occur in both emitters, leading to TADF properties. The donor units in SFST and SFOT have a sulfur and oxygen atom, respectively; such a subtle difference has great impacts on their photophysical, chiroptical, and electroluminescence (EL) properties. SFOT exhibits greatly enhanced EL performance in doped organic light-emitting diodes, with external quantum efficiency (EQE) up to 23.1%, owing to the concurrent manipulation of highly photoluminescent quantum efficiency (PLQY, ∼90%) and high exciton utilization. As a comparison, the relatively larger sulfur atom in SFST introduces heavy atom effects and leads to distortion of the molecular backbone that lengthens the donor-acceptor distance. SFST thus has lower PLQY and faster nonradiative decay rate. The collective consequence is that the EQE value of SFST, i.e., 12.5%, is much lower than that of SFOT. The chirality of these two spiro emitters results in circularly polarized luminescence. Because SFST has a more distorted molecular architecture than SFOT, the luminescence dissymmetry factor (|glum|) of circularly polarized luminescence of one enantiomer of the former, namely, either (S)-SFST or (R)-SFST, is almost twice that of (S)-SFOT/(R)-SFOT. Moreover, the CP organic light-emitting diodes (CP-OLEDs) show obvious circularly polarized electroluminescence (CPEL) signals with gEL of 1.30 × 10-3 and 1.0 × 10-3 for (S)-SFST and (S)-SFOT, respectively.

Chloride Insertion-Immobilization Enables Bright, Narrowband, and Stable Blue-Emitting Perovskite Diodes.

Metal halide perovskites show promise for light-emitting diodes (LEDs) owing to their facile manufacture and excellent optoelectronic performance, including high color purity and spectral stability, especially in the green region. However, for blue perovskite LEDs, the emission spectrum line width is broadened to over 25 nm by the coexistence of multiple reduced-dimensional perovskite domains, and the spectral stability is poor, with an undesirable shift (over 7 nm) toward longer wavelengths under operating conditions, degradation that occurs due to phase separation when mixed halides are employed. Here we demonstrate chloride insertion-immobilization, a strategy that enables blue perovskite LEDs, the first to exhibit narrowband (line width of 18 nm) and spectrally stable (no wavelength shift) performance. We prepare bromide-based perovskites and then employ organic chlorides for dynamic treatment, inserting and in situ immobilizing chlorides to blue-shift and stabilize the emission. We achieve sky-blue LEDs with a record luminance over 5100 cd/m2 at 489 nm, and an operating half-life of 51 min at 1500 cd/m2. By device structure optimization, we further realize an improved EQE of 5.2% at 479 nm and an operating half-life of 90 min at 100 cd/m2.

Optimal Dosing of Ceftriaxone in Infants Based on a Developmental Population Pharmacokinetic-Pharmacodynamic Analysis.

Ceftriaxone is a third-generation cephalosporin used to treat infants with community-acquired pneumonia. Currently, there is a large variability in the amount of ceftriaxone used for this purpose in this particular age group, and an evidence-based optimal dose is still unavailable. Therefore, we investigated the population pharmacokinetics of ceftriaxone in infants and performed a developmental pharmacokinetic-pharmacodynamic analysis to determine the optimal dose of ceftriaxone for the treatment of infants with community-acquired pneumonia. A prospective, open-label pharmacokinetic study of ceftriaxone was conducted in infants (between 1 month and 2 years of age), adopting an opportunistic sampling strategy to collect blood samples and applying high-performance liquid chromatography to quantify ceftriaxone concentrations. Developmental population pharmacokinetic-pharmacodynamic analysis was conducted using nonlinear mixed effects modeling (NONMEM) software. Sixty-six infants were included, and 169 samples were available for pharmacokinetic analysis. A one-compartment model with first-order elimination matched the data best. Covariate analysis elucidated that age and weight significantly affected ceftriaxone pharmacokinetics. According to the results of a Monte Carlo simulation, with a pharmacokinetic-pharmacodynamic target of a free drug concentration above the MIC during 70% of the dosing interval (70% fT>MIC), regimens of 20 mg/kg of body weight twice daily for infants under 1 year of age and 30 mg/kg twice daily for those older than 1 year of age were suggested. The population pharmacokinetics of ceftriaxone were established in infants, and evidence-based dosing regimens for community-acquired pneumonia were suggested based on developmental pharmacokinetics-pharmacodynamics.

Population pharmacokinetics and dose optimization of ceftriaxone for children with community-acquired pneumonia.

PURPOSE: To assess ceftriaxone population pharmacokinetics in a large pediatric population and describe the proper dose for establishing an optimized antibiotic regimen. METHODS: From pediatric patients using ceftriaxone, blood samples were obtained and the concentration was measured using high-performance liquid chromatography ultraviolet detection. The NONMEM software program was used for population pharmacokinetic analysis, for which data from 99 pediatric patients (2 to 12 years old) was collected and 175 blood concentrations were obtained. RESULTS: The best fit with the data was shown by the one-compartment model with first-order elimination. According to covariate analysis, weight had a significant impact on the clearance of ceftriaxone. Using Monte Carlo simulation, in a pediatric population with community-acquired pneumonia, a dose regimen of 100 mg/kg every 24 h produced satisfactory target attainment rates while remaining within the required minimum inhibitory concentration (2 mg/L). CONCLUSION: Population pharmacokinetics of ceftriaxone was evaluated in children and an optimum dosing regimen was constructed on the basis of the pharmacokinetics-pharmacodynamics model-based approach.

Discovery and mechanism of intestinal bacteria in enzymatic cleavage of C-C glycosidic bonds.

C-Glycosides, a special type of glycoside, are frequently distributed in many kinds of medicinal plants, such as puerarin and mangiferin, showing various and significant bioactivities. C-Glycosides are usually characterized by the C-C bond that forms between the anomeric carbon of sugar moieties and the carbon atom of aglycon, which is usually resistant against acidic hydrolysis and enzymatic treatments. Interestingly, C-glycosides could be cleaved by several intestinal bacteria, but whether the enzymatic cleavage of C-C glycosidic bond is reduction or hydrolysis has been controversial; furthermore, whether existence of a "C-glycosidase" directly catalyzing the cleavage is not clear. Here we review research advances about the discovery and mechanism of intestinal bacteria in enzymatic cleavage of C-C glycosidic bond with an emphasis on the identification of enzymes manipulation the deglycosylation. Finally, we give a brief conclusion about the mechanism of C-glycoside deglycosylation and perspectives for future study in this field.

Thiazolidin-2-cyanamides derivatives as novel potent Escherichia coli ß-glucuronidase inhibitors and their structure-inhibitory activity relationships.

Gut microbial ß-glucuronidases have the ability to deconjugate glucuronides of some drugs, thus have been considered as an important drug target to alleviate the drug metabolites-induced gastrointestinal toxicity. In this study, thiazolidin-2-cyanamide derivatives containing 5-phenyl-2-furan moiety (1-13) were evaluated for inhibitory activity against Escherichia coli ß-glucuronidase (EcGUS). All of them showed more potent inhibition than a commonly used positive control, d-saccharic acid 1,4-lactone, with the IC50 values ranging from 1.2 µM to 23.1 µM. Inhibition kinetics studies indicated that compound 1-3 were competitive type inhibitors for EcGUS. Molecular docking studies were performed and predicted the potential molecular determinants for their potent inhibitory effects towards EcGUS. Structure-inhibitory activity relationship study revealed that chloro substitution on the phenyl moiety was essential for EcGUS inhibition, which would help researchers to design and develop more effective thiazolidin-2-cyanamide type inhibitors against EcGUS.

Uric acid induced epithelial-mesenchymal transition of renal tubular cells through PI3K/p-Akt signaling pathway.

The phenotypic changes of tubular epithelial cell are hallmark features of renal diseases caused by abnormal uric acid levels. We hereby intend to investigate whether PI3K/p-Akt signaling plays a role in uric-acid induced epithelial-mesenchymal transition process. The normal rat kidney cell line (NRK-52E) was used as a proximal tubular cell model in this study. NRK-52E cells were exposed to different concentrations of uric acid, or PI3K inhibitor LY294002, or both, respectively. The effects of uric acid on cell morphology were examined by phase contrast microscopy, while molecular alternations were assessed by western blot analysis and immunofluorescence staining. We found that uric acid induced visible morphological alterations in NRK-52E cells accompanied by increased expression of α-smooth muscle actin and reduced expression of E-cadherin. Moreover, phosphorylation of Akt protein was obviously increased, whereas Akt level remained stable. Furthermore, the above effects were abolished when PI3K/p-Akt pathway was blocked by the PI3K inhibitor. These findings demonstrated that high uric acid could induce phenotypic transition of cultured renal tubular cells, which was probably via activating PI3K/p-Akt signaling pathway.