Relative dentin and enamel abrasivity of charcoal toothpastes.

OBJECTIVES: Very little data are known about charcoal toothpastes. The aim of this study was to counteract the missing data by determining the relative dentin abrasivity (RDA) and relative enamel abrasivity (REA) values of charcoal toothpastes. METHODS: Radioactively charged dentin and enamel samples were randomly divided into groups of eight specimens. Each group was brushed with two of total 12 charcoal toothpaste slurries and with a standard abrasive with a known RDA and REA value. The measured radioactivity in counts per minute within the slurries corresponds to the amount of dentin or enamel abraded. RDA and REA values of the charcoal toothpastes were expressed relative to the known value of the standard slurry. RESULTS: The RDA and REA values of the charcoal toothpastes have a broad range of 24-166 and 0-14, respectively. CONCLUSIONS: The RDA and REA values do not differ significantly from previously tested commercially available toothpastes. However, the lack of fluoride compounds in many of the investigated charcoal toothpastes can have a less beneficial effect for the consumers. It is very important to educate patients accordingly.

Interplay Between the In-Vitro Cleaning Performance and Wear of Manual Toothbrushes.

PURPOSE: This in-vitro study deals with the question of whether the wear and tear of the manual toothbrush over a simulated timeframe up to 24 months has an effect on its cleaning performance. The purpose was to find indications as to whether and when a toothbrush needs to be replaced based on its cleaning performance. MATERIALS AND METHODS: Models equipped with artificial teeth (coated with titanium dioxide) were brushed in-vitro using a brushing machine with clamped manual toothbrushes. The machine carried out even, horizontal brush strokes (120 brush strokes/min) for 1 min with a constant contact pressure of 2.5 N. The percentage of the area of titanium dioxide removed from the buccal, mesial and distal surfaces of the artificial teeth corresponded to the cleaning performance. The manual toothbrushes were used on bovine roots to simulate the wear and tear after 2, 4, 6, 12, 18, 24 months of use. The cleaning performance was re-evaluated after each simulated timepoint of wear. In addition, the brushes were photographed after each cycle. RESULTS: An increase in the in-vitro cleaning performance of the toothbrush was observed up to 6 months of wear compared to the starting point. After that, the cleaning performance decreased somewhat, but always remained above the initial cleaning performance. CONCLUSION: Based on the in-vitro cleaning performance after 24 months, the toothbrush would not have to be replaced. However, this in-vitro study cannot determine when a toothbrush should be replaced, because in-vivo it is also dependent on a variety of other factors such as fraying and microbial colonisation. Direct transfer of results from this study to everyday clinical practice is therefore difficult.

Wear of conventional and pre-polymerized composite materials under erosive/abrasive conditions.

The aim of this study was to examine the wear of three different composite materials usable for vertical bite reconstruction under erosive/abrasive conditions and to compare them with the bovine dental hard tissues enamel and dentin in-vitro. The composite materials Filtek Supreme XTE, CeraSmart and Brilliant Crios and bovine enamel and dentin specimens were evenly allocated to five groups (n=10). Samples were firstly exposed to hydrochloric acid for 1 min, then stored for 30 min in artificial saliva. In the second step, the samples were brushed for 1 min with 100 brushing strokes each and an applied force of 2.5 N in an automated brushing device. After 60 of these erosive/abrasive cycles, wear of the samples was determined by contact profilometry. Filtek Supreme XTE showed significantly less wear (mean ± standard deviation; 0.15 ± 0.11 µm) compared to the other two composite materials (p < 0.05). No significant difference (p > 0.05) could be found between CeraSmart (0.25 ± 0.03 µm) and Brilliant Crios (0.24 ± 0.04 µm). The two bovine dental hard tissues, enamel (13.70 ± 0.94 µm) and dentin (50.08 ± 4.46 µm), each showed a significantly higher amount of wear than the three restorative materials (p <0.05). In conclusion, this study exhibited that the three composite materials, Filtek Supreme XTE, CeraSmart and Brilliant Crios, were more resistant under erosive/abrasive conditions compared to bovine enamel and bovine dentin, respectively.

Homemade Modification of Salad Dressings to Reduce Their Erosive Potential.

PURPOSE: To investigate the possibility of reducing the erosive potential of salad dressings by adding yoghurt. MATERIALS AND METHODS: Two hundred enamel samples from bovine teeth were allocated to 20 groups (n = 10). Three modified commercially available balsamic dressings (addition of 10%, 20%, 50% yoghurt or 8.8 mM calcium chloride) and two homemade salad dressings with and without modifications were tested. Enamel samples were eroded for 2 min, rinsed for 30 s with tap water and finally abraded (20 brushing strokes with toothpaste slurry). After 40 of these cycles of erosion/abrasion, the dental hard tissue loss was determined by contact profilometry. RESULTS: For commercially available salad dressings, modification yielded a statistically significant decrease in enamel wear. The exception was Anna's Best Dressing Balsamico modified with 8.8 mM calcium chloride, for which no reduction was found compared with the unmodified dressing. For all homemade dressings, a significant reduction was observed when modified with 20% yoghurt. However, when only 10% yoghurt was added to the homemade dressings, an increase of the erosive potential was observed compared to the unmodified dressing. CONCLUSIONS: The study shows that increasing the calcium concentration only with calcium chloride in commercially available salad dressings did not show predictable outcomes to reduce erosion. However, mixing 20% plain yoghurt into the dressings reduced the erosive potential statistically significantly.