Evaluation of metal removal efficiency and its influence in the physicochemical parameters at two sewage treatment plants.

In sewage treatment plants, physicochemical parameters are highly controlled since treated sewage can be returned to water bodies or reused. In addition, pollutants such as heavy metals also deserve attention due to their potential toxicity. In general, these characteristics of sewage and treated water are evaluated independently, with the support of Brazilian legislation that does not require a routine for the analysis of metals as frequent as for the physicochemical parameters. In this work, 66 samples of raw sewage, treated sewage, and effluents from two treatment plants in the city of Bauru, São Paulo, Brazil, were evaluated to assess the efficiency of the treatment plants in the removal of metals. In addition, the influence of these pollutants on the quantification of physicochemical parameters was evaluated. The quantification of metals was performed using inductively coupled plasma optical spectroscopy (ICP-OES), and Spearman's test was applied to evaluate correlation between physicochemical parameters and metal content. The main metals found in the samples were Ba, Mn, Zn, Cu, Se, Fe, and Al. The results indicate that concentrations of metals in the aquatic environment can significantly affect the physicochemical parameters, since high concentrations of metals can interfere mainly in the pH, chemical oxygen demand, and dissolved oxygen.

On-Site Blackwater Treatment Fosters Microbial Groups and Functions to Efficiently and Robustly Recover Carbon and Nutrients.

Wastewater is considered a renewable resource water and energy. An advantage of decentralized sanitation systems is the separation of the blackwater (BW) stream, contaminated with human pathogens, from the remaining household water. However, the composition and functions of the microbial community in BW are not known. In this study, we used shotgun metagenomics to assess the dynamics of microbial community structure and function throughout a new BW anaerobic digestion system installed at The Netherlands Institute of Ecology. Samples from the influent (BW), primary effluent (anaerobic digested BW), sludge and final effluent of the pilot upflow anaerobic sludge blanket (UASB) reactor and microalgae pilot tubular photobioreactor (PBR) were analyzed. Our results showed a decrease in microbial richness and diversity followed by a decrease in functional complexity and co-occurrence along the different modules of the bioreactor. The microbial diversity and function decrease were reflected both changes in substrate composition and wash conditions. Our wastewater treatment system also decreased microbial functions related to pathogenesis. In summary, the new sanitation system studied here fosters microbial groups and functions that allow the system to efficiently and robustly recover carbon and nutrients while reducing pathogenic groups, ultimately generating a final effluent safe for discharge and reuse.

Screening of trace metal supplementation for black water anaerobic digestion.

Community on-site separation of wastewater is a treatment approach that leads to more efficient processes. Black water has high organic matter content and can be a suitable feedstock for anaerobic treatment systems. Biological methane production (BMP) tests were conducted using Plackett-Burman design to screen the effects of adding Fe, Ni, Cu, Co, Mn, Ba and Se, with simulated black water (SBW) as the substrate. In the inoculum, most metals were found mainly in the organic matter/sulfide and residual fractions except for Mn, which was present at 12.3% in the bioavailable fractions (exchangeable and carbonates), and Ba, which was evenly distributed among all the fractions. Ba had a significant negative effect on methane production and Mn addition enhanced the toxic effect. A specific methanogenic activity (SMA) between 18% and 27% lower than the control, was predicted at a total Ba concentration of approximately 1000-1200 mg L-1. Similar SMA was predicted at Ba concentration between 400 and 600 mg L-1 when 0.55 mg L-1 of Mn is added. Se and Cu additions demonstrate the potential to improve the methane production from SBW. The SMA was predicted to reach 12 mLCH4 gCOD-1 d-1 when Cu and Se are supplied at total concentrations of 3.0 mg L-1 and 0.98 mg L-1, respectively.

Natural lipids-based NLC containing lidocaine: from pre-formulation to in vivo studies.

In a nanotechnological approach we have investigated the use of natural lipids in the preparation of nanostructured lipid carriers (NLC). Three different NLC composed of copaiba oil and beeswax, sweet almond oil and shea butter, and sesame oil and cocoa butter as structural matrices were optimized using factorial analysis; Pluronic® 68 and lidocaine (LDC) were used as the colloidal stabilizer and model encapsulated drug, respectively. The optimal formulations were characterized by different techniques (IR-ATR, DSC, and TEM), and their safety and efficacy were also tested. These nanocarriers were able to upload high amounts of the anesthetic with a sustained in vitro release profile for 24h. The physicochemical stability in terms of size (nm), PDI, zeta potential (mV), pH, nanoparticle concentration (particles/mL), and visual inspection was followed during 12months of storage at 25°C. The formulations exhibited excellent structural properties and stability. They proved to be nontoxic in vitro (cell viability tests with Balb/c 3T3 fibroblasts) and significantly improved the in vivo effects of LDC, over the heart rate of zebra fish larvae and in the blockage of sciatic nerve in mice. The results from this study support that the proper combination of natural excipients is promising in DDS, taking advantage of the biocompatibility, low cost, and diversity of lipids.