CRISPR/Cas12a-Amplified Aptamer Switch Microplate Assay for Small Molecules.

The presence of small molecule contaminants such as mycotoxins and heavy metals in foods and the environment causes a serious threat to human health and huge economic losses. The development of simple, rapid, sensitive, and on-site methods for small molecule pollutant detection is highly demanded. Here, combining the advantages of structure-switchable aptamer-mediated signal conversion and CRISPR/Cas12a-based signal amplification, we developed a CRISPR/Cas12a-amplified aptamer switch assay on a microplate for sensitive small molecule detection. In this assay, a short DNA strand complementary to the aptamer (cDNA) is immobilized on a microplate, which can capture the aptamer-linked active DNA probe (Apt-acDNA) in the sample solution when the target is absent. With the addition of the Cas12a reporter system, the captured Apt-acDNA probes activate Cas12a to indiscriminately cleave fluorescent DNA substrates, producing a high fluorescence signal. When the target is present, the Apt-acDNA probe specifically binds to the target rather than hybridizing with cDNA on the microplate, and the fluorescence signal is reduced. The analytical performance of our method was demonstrated by the detection of two highly toxic pollutants, aflatoxin B1 (AFB1) and cadmium ion (Cd2+), as examples. The assay exhibited good selectivity and high sensitivity, with detection limits of 31 pM AFB1 and 3.9 nM Cd2+. It also allowed the detection of targets in the actual sample matrix. With the general signal conversion strategy, this method can be used to detect other targets by simply changing the aptamer and cDNA, showing potential practical applications in broad fields.

Zn-CD@Eu Ratiometric Fluorescent Probe for the Detection of Dipicolinic Acid, Uric Acid, and Ex Vivo Uric Acid Imaging.

Development of reliable methods for the detection of potential biomarkers is of the utmost importance for an early diagnosis of critical diseases and disorders. In this study, a novel lanthanide-functionalized carbon dot-based fluorescent probe Zn-CD@Eu is reported for the ratiometric detection of dipicolinic acid (DPA) and uric acid (UA). The Zn-CD@Eu nanoprobe was obtained from a simple room-temperature reaction of zinc-doped carbon dots (Zn-CD) and the EDTA-Eu lanthanide complex. Under optimal conditions, a good linear response was obtained for DPA in two concentration ranges of 0-55 and 55-100 µM with a limit of detection of 0.53 and 2.2 µM respectively, which is significantly below the infectious dosage of anthrax (∼55 µM). Furthermore, the Zn-CD@Eu/DPA system was employed for the detection of UA with a detection limit of 0.36 µM in the linear range of 0-100 µM. The fluorescent probe was successfully implemented for determining DPA and UA in human blood serum, sweat, and natural water bodies with considerable recovery rates. In addition, the potential of the nanoprobe for ex vivo visualization of UA was demonstrated in fruit fly (Drosophila melanogaster) as a model organism.

Bi(III) Binding Stoichiometry and Domain-Specificity Differences Between Apo and Zn(II)-bound Human Metallothionein 1a.

Bismuth is a xenobiotic metal with a high affinity to sulfur that is used in a variety of therapeutic applications. Bi(III) induces the cysteine-rich metallothionein (MT), a protein known to form two-domain cluster structures with certain metals such as Zn(II), Cd(II), or Cu(I). The binding of Bi(III) to MTs has been previously studied, but there are conflicting reports on the stoichiometry and binding pathway, which appear to be highly dependent on pH and initial metal-loading status of the MT. Additionally, domain specificity has not been thoroughly investigated. In this paper, ESI-MS was used to determine the binding constants of [Bi(EDTA)]- binding to apo-MT1a and its individual αMT fragment. The results were compared to previous experiments using ßMT1a and ßαMT3. Domain specificity was investigated using proteolysis methods and the initial cooperatively formed Bi2MT was found to bind to cysteines that spanned across the traditional metal binding domain regions. Titrations of [Bi(EDTA)]- into Zn7MT were performed and were found to result in a maximum stoichiometry of Bi7MT, contrasting the Bi6MT formed when [Bi(EDTA)]- was added to apo-MT. These results show that the initial structure of the apo-MT determines the stoichiometry of new incoming metals and explains the previously observed differences in stoichiometry.

Metal binding feature of copper‒induced metallothionein from freshwater crab Sinopotamon henanense reveals its Cu‒thionein character.

Sinopotamon Henanense expresses two metal‒induced metallothioneins (MTs), Cd‒induced MT and Cu‒induced MT (ShCuMT). The Cd‒induced MT has been characterized as a Cd‒thiolate MT. However, it is unknown whether ShCuMT is a Cu‒thiolate MT. In the present study, ShCuMT was expressed heterologously in Escherichia coli and purified by Ni‒NTA column and superdex‒75 column. And its metal‒binding feature was evaluated by DTNB reaction, circular dichroism spectroscopy (CD), isothermal microtitration (ITC), electrospray flight mass spectrometry (ESI‒TOF‒MS), and matrix‒assisted laser desorption ionization flight mass spectrometry (MALDI‒TOF‒MS). Bioinformatics analysis demonstrated that ShCuMT possessed the cysteine‒triplet motif of a Cu‒specific MT. Expression and purification of ShCuMT illustrated that SUMO tag used as the production system for ShCuMT resulted in a high production yield. The stability order of ShCuMT binding metal ions were Cu (Ⅰ) > Cd (Ⅱ) > Zn (Ⅱ). The CD spectrum indicated that ShCuMT binding with Cu (I) exhibited a compact thiol metal clusters structure. Besides, there emerged no a visible nickel‒thiol absorption after Ni‒NTA column affinity chromatography. The ITC results implied that Cu‒ShCuMT possessed the optimal thermodynamic conformation and the highest stoichiometric number of Cu (Ⅰ). Overall, the results suggested that SUMO fusion system is a robust and inexpensive approach for ShCuMT expression and Ni‒NTA column had no influence on metal binding of ShCuMT and Cu(Ⅰ) was considered its cognate metal ion, and ShCuMT possessed canonical Cu‒thiolate characteristics. The metal binding feature of ShCuMT reported here contributes to elucidating the structure‒function relationship of ShCuMT in S. Henanense.

Role of Histidine 310 in Amydetes vivianii firefly luciferase pH and metal sensitivities and improvement of its color tuning properties.

Firefly luciferases emit yellow-green light and are pH-sensitive, changing the bioluminescence color to red in the presence of heavy metals, acidic pH and high temperatures. These pH and metal-sensitivities have been recently harnessed for intracellular pH indication and toxic metal biosensing. However, whereas the structure of the pH sensor and the metal binding site, which consists mainly of two salt bridges that close the active site (E311/R337 and H310/E354), has been identified, the specific role of residue H310 in pH and metal sensing is still under debate. The Amydetes vivianii firefly luciferase has one of the lowest pH sensitivities among the group of pH-sensitive firefly luciferases, displaying high bioluminescent activity and special spectral selectivity for cadmium and mercury, which makes it a promising analytical reagent. Using site-directed mutagenesis, we have investigated in detail the role of residue H310 on pH and metal sensitivity in this luciferase. Negatively charged residues at position 310 increase the pH sensitivity and metal sensitivity; H310G considerably increases the size of the cavity, severely impacting the activity, H310R closes the cavity, and H310F considerably decreases both pH and metal sensitivities. However, no substitution completely abolished pH and metal sensitivities. The results indicate that the presence of negatively charged and basic side chains at position 310 is important for pH sensitivity and metals coordination, but not essential, indicating that the remaining side chains of E311 and E354 may still coordinate some metals in this site. Furthermore, a metal binding site search predicted that H310 mutations decrease the affinity mainly for Zn, Ni and Hg but less for Cd, and revealed the possible existence of additional binding sites for Zn, Ni and Hg.

Resistive pulse analysis of chiral amino acids utilizing metal-amino acid crystallization differences.

Here, we report a proof-of-concept resistive pulse method for analyzing chiral amino acids utilizing metal-amino acid crystallization differences. This method involves introducing an amino acid sample solution into a micropipette through a pressure-driven flow. The sample then mixes with a metal ion solution inside the pipette, forming metal-amino acid crystals. The crystal size depends on the enantiomeric excess (x) of chiral amino acid samples. Large x values lead to large crystals. The crystal size difference is then reflected in the resistive pulse size as they block the ionic transport in a micropipette to different extents. We used Cd-cystine crystallization as a model system and found approximately five times the mean current pulse size difference for racemic (x = 0) and L-only (x = +1) cystine samples. A similar result was observed for aspartate. Our discovery opens up new opportunities for micro/nanoscopic chiral amino acid analysis, which can potentially be used in single-cell analysis.

Metals and metallothionein evolution in snails: a contribution to the concept of metal-specific functionality from an animal model group.

This is a critical review of what we know so far about the evolution of metallothioneins (MTs) in Gastropoda (snails, whelks, limpets and slugs), an important class of molluscs with over 90,000 known species. Particular attention will be paid to the evolution of snail MTs in relation to the role of some metallic trace elements (cadmium, zinc and copper) and their interaction with MTs, also compared to MTs from other animal phyla. The article also highlights the important distinction, yet close relationship, between the structural and metal-selective binding properties of gastropod MTs and their physiological functionality in the living organism. It appears that in the course of the evolution of Gastropoda, the trace metal cadmium (Cd) must have played an essential role in the development of Cd-selective MT variants. It is shown how the structures and Cd-selective binding properties in the basal gastropod clades have evolved by testing and optimizing different combinations of ancestral and novel MT domains, and how some of these domains have become established in modern and recent gastropod clades. In this context, the question of how adaptation to new habitats and lifestyles has affected the original MT traits in different gastropod lineages will also be addressed. The 3D structures and their metal binding preferences will be highlighted exemplarily in MTs of modern littorinid and helicid snails. Finally, the importance of the different metal requirements and pathways in snail tissues and cells for the shaping and functionality of the respective MT isoforms will be shown.

Effect of voltage gradients on EK-PRB remediation: Experimental and molecular dynamics simulations.

Electrokinetic-Permeable Reaction Barrier (EK-PRB) coupled remediation technology can effectively treat heavy metal-contaminated soil near coal mines. This study was conducted on cadmium (Cd), a widely present element in the soil of the mining area. To investigate the impact of the voltage gradient on the remediation effect of EK-PRB, the changes in current, power consumption, pH, and Cd concentration content during the macroscopic experiment were analyzed. A three-dimensional visualized kaolinite-heavy metal-water simulation system was constructed and combined with the Molecular Dynamics (MD) simulations to elucidate the migration mechanism and binding active sites of Cd on the kaolinite (001) crystalline surface at the microscopic scale. The results showed that the voltage gradient positively correlates with the current, power consumption, and Cd concentration during EK-PRB remediation, and the average removal efficiency increases non-linearly with increasing voltage gradient. Considering power consumption, average removal efficiency, and cost-effectiveness, the voltage range is between 1.5 and 3.0 V/cm, with 2.5 V/cm being the optimal value. The results of MD simulations and experiments correspond to each other. Cd2+ formed a highly stable adsorption structure in contrast to the Al-O sheet on the kaolinite (001) crystalline surface. The mean square displacement (MSD) curve of Cd2+ under the electric field exhibits anisotropy, the total diffusion coefficient DTotal increases and the Cd2+ migration rate accelerates. The electric field influences the microstructure of Cd2+ complexes. With the enhancement of the voltage gradient, the complexation between Cd2+ and water molecules is enhanced, and the interaction between Cd2+ and Cl- in solution is weakened.

Removal of Cd from solution and in-situ remediation of Cd-contaminated soil by a mercapto-modified cellulose/bentonite intercalated nanocomposite.

A novel intercalated nanocomposite of mercapto-modified cellulose/bentonite (LCS-BE-SH) was synthesized by high-speed shearing method in one step at room temperature, and was applied to remove Cd from solution and remediate Cd-contaminated soil. Results revealed that cellulose long-chain molecules have intercalated into bentonite nanolayers and interlayer spacing was increased to 1.411 nm, and grafting -SH groups improved adsorption selectivity, which enabled LCS-BE-SH to have distinct capability of Cd adsorption (qmax = 147.21 mg/g). Kinetic and thermodynamics showed that Cd adsorption onto LCS-BE-SH was well fitted by pseudo-second-order and Langmuir adsorption isotherm. Characterizations of the adsorbents revealed that synergistic effect of complexation (e.g., CdS, CdO) and precipitation (e.g., Cd(OH)2, CdCO3) mechanism played a major role in Cd removal. In soil remediation, application of LCS-BE-SH was most effective (67.31 %) in Cd immobilization compared to the control (8.85 %), which reduced exchangeable Cd from 37.03 % to 11.44 %. Meanwhile, soil pH, soil organic matter, available phosphorus, and enzyme activities (catalase, urease, and dehydrogenase) were improved LCS-BE-SH treatment. The main immobilization mechanism in soil included complexation (e.g., CdS, CdO) and precipitation (e.g., Cd(OH)2, Cd-Fe-hydroxide). Overall, this work applied a promising approach for Cd removal in aqueous and Cd remediation in soil by using an effective eco-friendly LCS-BE-SH nanocomposites.

Immobilization mechanisms of Sr(II), Ni(II), and Cd(II) on glomalin-related soil protein in mangrove sediments at the microscopic scale.

Glomalin-related soil protein (GRSP) is a significant component in the sequestration of heavy metal in soils, but its mechanisms for metal adsorption are poorly known. This study combined spectroscopic data with molecular docking simulations to reveal metal adsorption onto GRSP's surface functional groups at the molecular level. The EXAFS combined with FTIR and XPS analyses indicated that the adsorption of Cd(II), Sr(II), and Ni(II) by GRSP occurred mainly through the coordination of -OH and -COOH groups with the metal. The -COOH and -OH groups bound to the metal as electron donors and the electron density of the oxygen atom decreased, suggesting that electrostatic attraction might be involved in the adsorption process. Two-dimensional correlation spectroscopy revealed that preferential adsorption occurred on GRSP for the metal in sequential order of -COOH groups followed by -OH groups. The presence of the Ni-C shell in the Ni EXAFS spectrum suggested that Ni formed organometallic complexes with the GRSP surface. However, Sr-C and Cd-C were absent in the second shell of the Sr and Cd spectra, which was attributed to the adsorption of Sr and Cd ions with large hydration ion radius by GRSP to form outer-sphere complexes. Through molecular docking simulations, negatively charged residues such as ASP151 and ASP472 in GRSP were found to provide electrostatic attraction and ligand combination for the metal adsorption, which was consistent with the spectroscopic analyses. Overall, these findings provided new insights into the interaction mechanisms between GRSP and metals, which will help deepen our understanding of the ecological functions of GRSP in metal sequestration.

Evaluation of Zn-Cd-Sn-S nanostructures for in vitro pyrene degradation and antimicrobial activity.

The present work describes the fabrication of the quaternary Zn-Cd-Sn-S nanostructure and its use in photocatalytic remediation of the biological contaminant pyrene from water resources. Nanostructures fabricated were characterized by XRD, UV-DRS, FTIR, DLS, EDX, and SEM. In addition, an agar well diffusion test was conducted to determine the antimicrobial activity. Zn-Cd-Sn-S (ZCSS) nanostructures were evaluated for their photocatalytic degrading potential by using pyrene as a model pollutant and evaluating the effects of parameters like initial pyrene concentration, nanocatalyst dosage, solution pH, and light sources during batch adsorption. Nanostructures had a size of 16.74 nm according to the XRD analysis. With a 300 min time interval, ZCSS nanostructures achieved the highest removal rate of 86.3%. Pyrene degradation metabolites were identified using GC-MS analysis of the degraded samples. A Freundlich isothermal (R2 0.9) and pseudo-first-order (R2 0.952) reaction kinetic path best fit the adsorption results for pyrene by the fabricated ZCSS nanostructure, based on the adsorption and kinetic studies. Zn-Cd-Sn-S exhibited the highest antibacterial activity against Staphylococcusaureus (22.4 mM). Due to the combined synergistic actions of the constituent metals, this quaternary nanostructure exhibited exceptional photocatalytic activity. To our est knowledge, the ZCSS nanostructure was made and used to remove pyrene by photocatalysis and fight microbes. Ultimately, the ZCSS nanostructure was found to be an effective photocatalyst for eradicating pathogenic microbes from water.

Recalcification stabilizes cadmium but magnifies phosphorus limitation in wastewater-irrigated calcareous soil.

Long-term wastewater irrigation leads to the loss of calcium carbonate (CaCO3) in the tillage layer of calcareous land, which irreversibly damages the soil's ability to retain cadmium (Cd). In this study, we selected calcareous agricultural soil irrigated with wastewater for over 50 years to examine the recalcification effects of sugar beet factory lime (SBFL) at doses of 0%, 2.5%, 5%, and 10%. We found that SBFL promoted Cd transformation in the soil from active exchangeable species to more stable carbonate-bonded and residual species, which the X-ray diffraction patterns also confirmed results that CdSO4 reduced while CdS and CaCdCO3 increased. Correspondingly, the soil bioavailable Cd concentration was significantly reduced by 65.6-84.7%. The Cd concentrations in maize roots and shoots were significantly reduced by 11.7-50.6% and 13.0-70.0%, respectively, thereby promoting maize growth. Nevertheless, SBFL also increased the proportion of plant-unavailable phosphorus (P) in Ca8-P and Ca10-P by 4.3-13.0% and 10.7-25.9%, respectively, reducing the plant-available P (Olsen P) content by 5.2-22.1%. Consequently, soil P-acquiring associated enzyme (alkaline phosphatase) activity and microbial (Proteobacteria, Bacteroidota, and Actinobacteria) community abundance significantly increased. Our findings showed that adding SBFL to wastewater-irrigated calcareous soil stabilized Cd, but exacerbated P limitation. Therefore, it is necessary to alleviate P limitations in the practice of recalcifying degraded calcareous land.

Deferiprone: new environmental perspectives. Insights into its sequestering ability vs. different metal cations.

Deferiprone, generally, is considered an important chelating agent for Fe3+ overload. From a literature data analysis, a lack of information on the interaction of this molecule toward a series of metal cations emerged, inducing to fill out the topic. The complexing ability of deferiprone toward Ca2+, Mg2+, Cd2+ and Pb2+ was studied by potentiometry and 1H NMR spectroscopy, in KCl aqueous solutions at different ionic strength values (0.1 ≤ I/mol dm-3 ≤ 1.0) and T = 298.15 K. The same speciation model featured by the ML, ML2, ML3 and ML(OH) (M = metal and L = deferiprone or DFP) species was obtained for Cd2+ and Pb2+; the formation constants calculated at infinite dilution are: logTß = 7.23±0.02, 12.47±0.03, 16.70±0.04, and -2.53±0.04, respectively for Cd2+ and 9.91±0.01, 15.99±0.02, 19.93±0.05 and 0.99±0.02 for Pb2+. Only two species, namely ML and ML2, were determined for Ca2+ and Mg2+, whose formation constants at infinite dilution are respectively: 3.72±0.01 and 6.50±0.02, for the first one, 5.31±0.01 and 9.58±0.01, for the second. The ligand sequestering ability and affinity toward M2+ were evaluated by determining the pL0.5 and pM parameters at different pHs and ionic strengths. The results suggest that deferiprone has the best complexing and sequestering ability toward Pb2+, followed by Cd2+, Mg2+ and Ca2+, respectively. 1H NMR studies confirmed the DFP affinity for Cd2+ and Pb2+, and in combination with DFT calculations showed that metal cations are bound to the hydroxo-oxo moiety of the pyridinone ring. The data reported in this study provide information on the possible employment of a small molecule like deferiprone, as a chelating and sequestering agent for Pb2+ accumulation or overload from environmental and biological matrices.

Changes in the extractability and fractionation of cadmium and copper in a contaminated soil amended with various sugarcane bagasse-based materials.

Heavy-metal contamination in soil has long been a persistent challenge and the utilization of agricultural waste for in-situ stabilization remediation presents a promising approach to tackle this problem. Agricultural wastes exhibit promising potential in the remediation of contaminated land and modification could improve the adsorption performance markedly. Citric acid and Fe3O4 treated sugarcane bagasse adsorbed more heavy metals than raw materials in the aqueous system, employing these materials for heavy metal remediation in soil holds significant implications for broadening the raw material source of passivators and enhancing waste utilization efficiency. In this paper, a 120-day soil incubation study was conducted to compare the effects of pristine sugarcane bagasse (SB), citric-acid modified (SSB1, SSB2 and SSB3 with increasing proportion of citric acid) and citric-acid/Fe3O4 modified (MSB1, MSB4 and MSB7 with increasing proportion of Fe3O4) sugarcane bagasse at 1 % addition rate on cadmium (Cd) and copper (Cu) passivation. The SB, SSB1 and MSB1 did not always decrease the content of CaCl2-extractable Cd while all the seven amendments decreased the CaCl2-extractable Cu during the experiment period. Among all materials, SSB3 and MSB7 exhibited the highest efficiency in reducing the concentrations of CaCl2-extractable Cd and Cu. At Day 120, SB, SSB3 and MSB7 reduced the content of CaCl2-extractable Cd by 8 %, 18 % and 24 %, and of CaCl2-extractable Cu by 25 %, 50 % and 61 %, respectively. The efficiency of Cd and Cu immobilization was associated positively with the pH, functional groups and H-bonds of the amendments. The results suggest that the efficiency of sugarcane bagasse in heavy-metal passivation can be largely enhanced through chemical modifications using high proportions of citric acid and Fe3O4.

New penta-Coordinated Cadmium(II) Complexes: Synthesis, Characterization, Thermal, Antimicrobial, Antioxidant and Cytotoxicity Properties.

In this paper, a new tridentate Schiff base ligand (L) with nitrogen donor atoms and its cadmium(II) complexes with the general formula of CdLX2 (X=Cl-, Br-, I-, SCN-, N3 -, NO3 -) have been synthesized and characterized by physical and spectral (FT/IR, UV-Vis, Mass, and 1H, 13C NMR spectroscopies) methods. Also nano-structured cadmium chloride and bromide complexes were synthesized by sonochemical method and then used to prepare nanostructured cadmium oxide confirmed by XRD and SEM techniques. Thermal behavior of the compounds was studied in the temperature range of 25 to 900 °C under N2 atmosphere at a heating rate of 20 °C/ min. Moreover, thermo-kinetic activation parameters of thermal decomposition steps were calculated according to the Coats-Redfern relationship. Antimicrobial activities of the synthesized compounds against two gram-positive and two gram-negative bacteria such as Bacillus subtilis, Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa, and two fungi of Candida albicans and Aspergillus niger were investigated by well diffusion method. SEM technique was used to monitor the morphological changes of the bacteria treated with the compounds. The 2,2-Diphenyl-1-picrylhydrazyl(DPPH) and the ferric reducing antioxidant power (FRAP) methods were used to evaluate the antioxidant ability of the ligand and its cadmium(II) complexes. In final, the cytotoxicity properties of the ligand and some cadmium(II) complexes against PC3 cancer cells were evaluated by MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-2H-tetrazolium bromide) bioassay and nitric oxide (NO) level measurement. The morphological changes of prostate cancer (PC3) cells due to treatment with the ligand and its complexes confirmed their anticancer effectiveness.

A competitive-type photoelectrochemical aptasensor for 17 beta-estradiol detection in microfluidic devices based on a novel Au@Cd:SnO2/SnS2 nanocomposite.

A competitive-type photoelectrochemical (PEC) aptasensor coupled with a novel Au@Cd:SnO2/SnS2 nanocomposite was designed for the detection of 17ß-estradiol (E2) in microfluidic devices. The designed Au@Cd:SnO2/SnS2 nanocomposites exhibit high photoelectrochemical activity owing to the good matching of cascade band-edge and the efficient separation of photo-generated e-/h+ pairs derived from the Cd-doped defects in the energy level. The Au@Cd:SnO2/SnS2 nanocomposites were loaded into carbon paste electrodes (CPEs) to immobilize complementary DNA (cDNA) and estradiol aptamer probe DNA (E2-Apt), forming a double-strand DNA structure on the CPE surface. As the target E2 interacts with the double-strand DNA, E2-Apt is sensitively released from the CPE, subsequently increasing the photocurrent intensity due to the reduced steric hindrance of the electrode surface. The competitive-type sensing mechanism, combined with high PEC activity of the Au@Cd:SnO2/SnS2 nanocomposites, contributed to the rapid and sensitive detection of E2 in a "signal on" manner. Under the optimized conditions, the PEC aptasensor exhibited a linear range from 1.0 × 10-13 mol L-1 to 3.2 × 10-6 mol L-1 and a detection limit of 1.2 × 10-14 mol L-1 (S/N = 3). Moreover, the integration of microfluidic device with smartphone controlled portable electrochemical workstation enables the on-site detection of E2. The small sample volume (10 µL) and short analysis time (40 min) demonstrated the great potential of this strategy for E2 detection in rat serum and river water. With these advantages, the PEC aptasensor can be utilized for point-of-care testing (POCT) in both clinical and environmental applications.

Green and effective remediation of heavy metals contaminated water using CaCO3 vaterite synthesized through biomineralization.

Heavy metal pollution has attracted significant attention due to its persistent presence in aquatic environments. A novel vaterite-based calcium carbonate adsorbent, named biogenic CaCO3, was synthesized utilizing a microbially induced carbonate precipitation (MICP) method to remediate heavy metal-contaminated water. The maximum Cd2+ removal capacity of biogenic CaCO3 was 1074.04 mg Cd2+/g CaCO3 with a high Cd2+ removal efficiency greater than 90% (initial Cd2+ concentration 400 mg/L). Furthermore, the biogenic CaCO3 vaterite, induced by microbial-induced calcium carbonate precipitation (MICP) process, demonstrated a prolonged phase transformation to calcite and enhanced stability. This resulted in a sustained high effectiveness (greater than 96%) following six consecutive recycling tests. Additionally, X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses revealed that the semi-stable vaterite type of biogenic CaCO3 spontaneously underwent dissolution and recrystallization to form thermodynamic stable calcite in aquatic environments. However, the presence of Cd2+ leads to the transformation of vaterite into CdCO3 rather than undergoing direct converting to calcite. This transformation is attributed to the relatively low solubility of CdCO3 compared to calcite. Meanwhile, the biogenic CaCO3 proved to be an efficient and viable method for the removal of Pb2+, Cu2+, Zn2+, Co2+, Ni2+ and Mn2+ from water samples, surpassing the performance of previously reported adsorbents. Overall, the efficient and promising adsorbent demonstrates potential for practical in situ remediation of heavy metals-contaminated water.

Transport and transformations of cadmium in water-biofilm-sediment phases as affected by hydrodynamic conditions.

Hydrodynamic conditions play a crucial role in governing the fate, transport, and risks of metal elements. However, the contribution of hydrodynamic conditions to the fate and transport of heavy metals among water, sediment, and biofilm phases is poorly understood. In our study, we conducted experiments in controlled hydrodynamic conditions using a total of 6 two-phase and 9 three-phase mesocosms consisting of water, biofilm, and sediment. We also measured Cd (cadmium) specification in different phases to assess how hydrodynamic forces control Cd bioavailability. We found that turbulent flow destroyed the surface morphology of the biofilm and significantly decreased the content of extracellular polymeric substances (p < 0.05). This led to a decrease in the biofilm's adsorption capacity for Cd, with the maximum adsorption capacity (0.124 mg/g) being one-tenth of that under static conditions (1.256 mg/g). The Cd chemical forms in the biofilm and sediment were significantly different, with the highest amount of Cd in the biofilm being acid-exchangeable, accounting for up to 95.1% of the total Cd content. Cd was more easily released in the biofilm due to its weak binding state, while Cd in the sediment existed in more stable chemical forms. Hydrodynamic conditions altered the migration behavior and distribution characteristics of Cd in the system by changing the adsorption capacity of the biofilm and sediment for Cd. Cd mobility increased in laminar flow but decreased in turbulent flow. These results enhance our understanding of the underlying mechanisms that control the mobility and bioavailability of metals in aquatic environments with varying hydrodynamic conditions.

Elevated CO2 and nitrogen addition enhance the symbiosis and functions of rhizosphere microorganisms under cadmium exposure.

Soil microbes are fundamental to ecosystem health and productivity. How soil microbial communities are influenced by elevated atmospheric carbon dioxide (eCO2) concentration and nitrogen (N) deposition under heavy metal pollution remains uncertain, despite global exposure of terrestrial ecosystems to eCO2, high N deposition and heavy metal stress. Here, we conducted a four year's open-top chamber experiment to assess the effects of soil cadmium (Cd) treatment (10 kg hm-2 year-1) alone and combined treatments of Cd with eCO2 concentration (700 ppm) and/or N addition (100 kg hm-2 year-1) on tree growth and rhizosphere microbial community. Relative to Cd treatment alone, eCO2 concentration in Cd contaminated soil increased the complexity of microbial networks, including the number links, average degree and positive/negative ratios. The combined effect of eCO2 and N addition in Cd contaminated soil not only increased the complexity of microbial networks, but also enhanced the abundance of microbial urealysis related UreC and nitrifying related amoA1 and amoA2, and the richness of arbuscular mycorrhiza fungi (AMF), thereby improving the symbiotic functions between microorganisms and plants. Results from correlation analysis and structural equation model (SEM) further demonstrated that eCO2 concentration and N addition acted on functions and networks differently. Elevated CO2 positively regulated microbial networks and functions through phosphorus (P) and Cd concentration in roots, while N addition affected microbial functions through soil available N and soil organic carbon (SOC) concentration and microbial network through soil Cd concentration. Overall, our findings highlight that eCO2 concentration and N addition make microbial communities towards ecosystem health that may mitigate Cd stress, and provide new insights into the microbiology supporting phytoremediation for Cd contaminated sites in current and future global change scenarios.

Mobility, speciation of cadmium, and bacterial community composition along soil depths during microbial carbonate precipitation under simulated acid rain.

An overexploitation of earth resources results in acid deposition in soil, which adversely impacts soil ecosystems and biodiversity and affects conventional heavy metal remediation using immobilization. A series of column experiments was conducted in this study to compare the cadmium (Cd) retention stability through biotic and abiotic carbonate precipitation impacted by simulated acid rain (SAR), to build a comprehensive understanding of cadmium speciation and distribution along soil depth and to elucidate the biogeochemical bacteria-soil-heavy metal interfaces. The strain of Sporosarcina pasteurii DSM 33 was used to trigger the biotic carbonate precipitation and cultivated throughout the 60-day column incubation. Results of soil pH, electrical conductivity (EC), and quantitative CdCO3/CaCO3 analysis concluded that the combination of biotic and abiotic soil treatment could reinforce soil buffering capacity as a strong defense mechanism against acid rain disturbance. Up to 1.8 ± 0.04 U/mg urease enzyme activity was observed in combination soil from day 10, confirming the sustained effect of urease-mediated microbial carbonate precipitation. Cadmium speciation and distribution analyses provided new insights into the dual stimulation of carbonate-bound and Fe/Mn-bound phases of cadmium immobilization under microbially induced carbonate precipitation (MICP). As confirmed by the microbial community analysis, outsourcing urea triggered diverse microbial metabolic responses, notably carbonate precipitation and dissimilatory iron metabolism, in both oxygen-rich topsoil and oxygen-depleted subsurface layers. The overall investigation suggests the feasibility of applying MICP for soil Cd remediation under harsh environments and stratagem by selecting microbial functionality to overcome environmental challenges.