CT Fluoroscopy for Image-Guided Procedures: Physician Radiation Dose During Full-Rotation and Partial-Angle CT Scanning.

PURPOSE: To determine physician radiation exposure when using partial-angle computed tomography (CT) fluoroscopy (PACT) vs conventional full-rotation CT and whether there is an optimal tube/detector position at which physician dose is minimized. MATERIALS AND METHODS: Physician radiation dose (entrance air kerma) was measured for full-rotation CT (360°) and PACT (240°) at all tube/detector positions using a human-mimicking phantom placed in a 64-channel multidetector CT. Parameters included 120 kV, 20- and 40-mm collimation, and 100 mA. The mean, standard deviation, and increase/decrease in physician dose compared with a full-rotation scan were reported. RESULTS: Physician radiation exposure during CT fluoroscopy with PACT was highly dependent on the position of the tube/detector during scanning. The lowest PACT physician dose was when the physician was on the detector side (center view angle 116°; -35% decreased dose vs full-angle CT). The highest PACT physician dose was with the physician on the tube side (center view angle 298°; +34% increased dose vs full-angle CT), all doses P <.05 vs full-rotation CT. CONCLUSIONS: Partial-angle CT has the potential to both significantly increase or decrease physician radiation dose during CT fluoroscopy-guided procedures. The detector/tube position has a profound effect on physician dose. The lowest dose during PACT was achieved when the physician was located on the detector side (ie, distant from the tube). This data could be used to optimize CT fluoroscopy parameters to reduce physician radiation exposure for PACT-capable scanners.

Optimizing Identification of Power Injectable Ports on the Scout Images for Multidetector Computed Tomography Procedures.

OBJECTIVE: The objective of this study was to assess the impact of tube voltage and image display on the identification of power ports features on anterior-posterior scout images to inform optimal workflow for multidetector computed tomography (MDCT) examinations. MATERIALS AND METHODS: Four ports, representing variable material composition (titanium/silicone), shapes, and computed tomography (CT) markings, were imaged on an adult anthropomorphic chest phantom using a dual-source MDCT at variable peak tube voltages (80, 100, 120, 150, and Sn150 kVp). Images were reviewed at variable image display setting by 5 blinded readers to assess port features of material composition, shape, and text markings as well as overall preferred image quality. RESULTS: Material composition was correctly identified for all ports by all readers across all kilovoltage-peak settings. The identification by shape was more reliable than CT markers for all but one of the ports. CT marker identification was up to 80% for titanium ports at window level settings optimized for metal (window width, 200; window center, -150) and at a soft tissue setting (window width, 400; window center, 40) for silicone ports. Interreader agreement for best image quality per kilovoltage-peak setting was moderate to substantial for 3 ports (k = 0.5-0.62) but only fair for 1 port (k = 0.27). The highest overall rank for image quality was given unanimously to Sn150 kVp for imaging titanium ports and 100 kVp for silicone ports. CONCLUSIONS: Power port identification on MDCT scout images can be optimized with modification of MDCT scout acquisition and display settings based on the main port material.

In vitro optimization and comparison of CT angiography versus radial cardiovascular magnetic resonance for the quantification of cross-sectional areas and coronary endothelial function.

BACKGROUND: Our objectives were first to determine the optimal coronary computed tomography angiography (CTA) protocol for the quantification and detection of simulated coronary artery cross-sectional area (CSA) differences in vitro, and secondly to quantitatively compare the performance of the optimized CTA protocol with a previously validated radial coronary cardiovascular magnetic resonance (CMR) technique. METHODS: 256-multidetector CTA and radial coronary CMR were used to obtain images of a custom in vitro resolution phantom simulating a range of physiological responses of coronary arteries to stress. CSAs were automatically quantified and compared with known nominal values to determine the accuracy, precision, signal-to-noise ratio (SNR), and circularity of CSA measurements, as well as the limit of detection (LOD) of CSA differences. Various iodine concentrations, radiation dose levels, tube potentials, and iterative image reconstruction algorithms (ASiR-V) were investigated to determine the optimal CTA protocol. The performance of the optimized CTA protocol was then compared with a radial coronary CMR method previously developed for endothelial function assessment under both static and moving conditions. RESULTS: The iodine concentration, dose level, tube potential, and reconstruction algorithm all had significant effects (all p <  0.001) on the accuracy, precision, LOD, SNR, and circularity of CSA measurements with CTA. The best precision, LOD, SNR, and circularity with CTA were achieved with 6% iodine, 20 mGy, 100 kVp, and 90% ASiR-V. Compared with the optimized CTA protocol under static conditions, radial coronary CMR was less accurate (- 0.91 ± 0.13 mm2 vs. -0.35 ± 0.04 mm2, p <  0.001), but more precise (0.08 ± 0.02 mm2 vs. 0.21 ± 0.02 mm2, p <  0.001), and enabled the detection of significantly smaller CSA differences (0.16 ± 0.06 mm2 vs. 0.52 ± 0.04 mm2; p <  0.001; corresponding to CSA percentage differences of 2.3 ± 0.8% vs. 7.4 ± 0.6% for a 3-mm baseline diameter). The same results held true under moving conditions as CSA measurements with CMR were less affected by motion. CONCLUSIONS: Radial coronary CMR was more precise and outperformed CTA for the specific task of detecting small CSA differences in vitro, and was able to reliably identify CSA changes an order of magnitude smaller than those reported for healthy physiological vasomotor responses of proximal coronary arteries. However, CTA yielded more accurate CSA measurements, which may prove useful in other clinical scenarios, such as coronary artery stenosis assessment.

Accuracy of Pulmonary Nodule Volumetry at Different Exposure Parameters in Low-Dose Computed Tomography: A Phantom Study.

OBJECTIVE: To explore the exposure parameters with minimized radiation dose for accurate pulmonary nodule volumetry using low-dose computed tomography (LDCT). METHODS: An anthropomorphic chest phantom with 11 pulmonary nodules (6 solid nodules and 5 ground-glass opacities) was scanned using 256-slice multidetector computed tomography scanner at various tube voltage and current (combinations of 80, 100 and 120 kV with 10 to 30 mAs). Raw data sets were reconstructed using the hybrid iterative reconstruction method and nodule volume was calculated by a semiautomatic software. The absolute percentage error (APE) of nodule volume relating to the reference acquisition and contrast-to-noise ratio was measured. RESULTS: Nodule characteristic and tube voltage (P < 0.0001) as well as the interaction between nodule characteristic and tube voltage (P = 0.0026) contributed significantly to the mean difference of APE, while tube current did not (P = 0.21). Post hoc analysis revealed no significant difference was found between the APE at 100 kV and 120 kV in both solid nodules (2.3 ± 0.4% vs 1.8 ± 0.6%, P = 0.14) and ground-glass opacities (6.0 ± 0.5% vs 4.9 ± 0.6%, P = 0.11). Exploratory analyses further showed that the APE at 100 kV with 10 mAs did not differ from that at 120 kV with 30 mAs in both solid nodules (2.5 ± 0.5% vs 1.7 ± 0.3%, P = 0.025, corrected P = 0.20) and ground-glass opacities (6.4 ± 0.4% vs 4.8 ± 1.0%, P = 0.0084, corrected P = 0.068). CONCLUSIONS: In our study, the exposure parameters with minimized radiation dose for accurate pulmonary nodule volumetry were found at 100 kV with 10 mAs, and the estimated effect radiation dose was as low as 0.2 mSv, suggesting the feasibility of further reducing radiation dose by decreasing tube voltage and current in LDCT lung screening.

The Utility of Virtual Bronchoscopy Using a Computed Tomography Workstation for Conducting Conventional Bronchoscopy: A Retrospective Analysis of Clinical Practice.

BACKGROUND: Recent clinical trials demonstrated the benefits of several guided-bronchoscopy technologies for the diagnosis of peripheral pulmonary lesions (PPLs). However, introduction of these technologies is expensive. Therefore, in clinical practice, these are unavailable in many hospitals. In contrast, virtual bronchoscopy (VB) using the computed tomography (CT) workstation can be made available immediately without additional cost as many hospitals already have the CT scan facility. However, the effectiveness of VB alone remains to be shown. OBJECTIVES: The aim of this study was to investigate the effect of VB using the CT workstation in hospitals performing conventional bronchoscopy. METHODS: Results from consecutive patients who underwent bronchoscopy for small PPLs (major diameter ≤30 mm) were retrospectively reviewed. Sixty-nine patients who underwent bronchoscopy without VB from April 2014 to March 2015 and 56 patients who underwent bronchoscopy with VB from April 2015 to December 2015 were assigned to non-VB and VB groups, respectively. We compared the two groups and analyzed the factors affecting the diagnostic yield. RESULTS: The VB group had a significantly higher diagnostic yield than the non-VB group (57.1 vs. 33.3%; p = 0.008). In the multivariate analysis, VB was identified as a significant factor affecting the diagnostic yield (odds ratio: 3.30, p = 0.011). CONCLUSIONS: In the conventional bronchoscopy settings, VB using the CT workstation is efficient for the diagnosis of PPLs when other guided-bronchoscopy techniques are unavailable.

[Acute abdominal trauma]. / Traumatisches akutes Abdomen.

BACKGROUND: In patients with multiple trauma, abdominal involvement is a particularly relevant injury pattern. Depending on the intensity and manner of injury, heterogeneous but often typical organ manifestations result. Knowledge of these injury patterns is essential for targeted diagnostics and treatment. OBJECTIVE: This review provides a presentation of typical forms of abdominal injury with appropriate radiological techniques and where applicable treatment. MATERIAL AND METHODS: Experiences and case examples from a supraregional trauma center are presented and discussed with the results of a Medline literature search and relevant parts of the german S3 guidelines on polytrauma. RESULTS: Traumatic abdominal injuries are subdivided into blunt and penetrating injuries. Among these groups, blunt trauma with splenic injury being most frequent followed by liver and kidney involvement. In penetrating abdominal injuries hollow visceral organs are most frequently affected. For diagnosis, ultrasound and with escalating injury severity, multidetector computed tomography (MDCT) are the most important methods. For years there has been an ongoing trend towards conservative management and interventional hemorrhage control. This is driven by improvements in imaging that enable a more precise classification and indications for subsequent treatment. CONCLUSION: Progress in radiology has led to an increasingly more important role for radiology in the management of traumatic abdominal injury. Therefore, it is crucial for the radiologist to gain interdisciplinary knowledge of the relevant trauma mechanisms and injury patterns of the severely injured patient in order to provide a treatment process that provides the optimal outcome.

Trends in radiation dose and image quality for pediatric patients with a multidetector CT and a third-generation dual-source dual-energy CT.

AIM: To provide an overview on dose reduction and image quality after the installation of a third-generation dual-source CT (dsCT) in a Pediatric Radiology Department. MATERIALS AND METHODS: We included pediatric patients (< 20 years old) undergoing CT for oncological staging (neck, chest and abdomen) or low-dose chest CT for lung diseases. Each of these two groups were further divided in two age groups (≤ or > 10 years old) including patients scanned in the same period of two consecutive years, in 2017 with a 16-row LightSpeed CT (GE Healthcare) or in 2018 with a Somatom Force dsCT (Siemens Healthineers). Technical parameters such as kVp, mAs, slice thickness, exposure times and dose indicators were retrieved and compared. Image quality was evaluated in consensus by two radiologists on a five-point semiquantitative scale. Nonparametric tests were used. RESULTS: In oncological patients, significantly lower kVp and tube current with better image quality were achieved with the dsCT. Radiation dose (total DLP) was 5-6 times lower with dsCT, thanks also to virtual non-contrast images. In low-dose chest CT, the frequent use of tin filter required higher tube current; a total DLP 3 times lower was achieved with dsCT in patients ≤ 10 years old. The image quality was better with the dsCT in low-dose chest CT protocols. CONCLUSION: The third-generation dsCT provides high-quality images with reduced motion artifacts at lower dose.

Radiation exposure related to cardiovascular CT examination: comparison between conventional 64-MDCT and third-generation dual-source MDCT.

PURPOSE: To compare radiation exposure associated with daily practice cardiovascular (CV) examinations performed on two different multidetector computed tomography (MDCT) scanners, a conventional 64-MDCT and a third-generation dual-source (DS) MDCT. MATERIALS AND METHODS: In this retrospective study, 1458 patients who underwent CV examinations between January 2017 and August 2018 were enrolled. A single-source 64-MDCT (Lightspeed VCT, GE) scan was performed in 705 patients from January to August 2017 (207 coronary examinations and 498 vascular examinations) and 753 patients underwent third-generation 192 × 2-DSCT (Somatom FORCE, Siemens) scan from January to August 2018 (302 coronary examinations and 451 vascular examinations). Volume CT dose index (CTDIvol), dose length product (DLP), effective dose (ED), tube voltage (TV) and exposure time (ET), pitch factor (PF) were registered for each patient. Student's t test was used to compare mean values between each corresponding group of MDCT and DSCT. RESULTS: In coronary examinations with DSCT, CTDIvol was 24.4% lower (23.1 mGy vs 30.6 mGy, p < 0.0001) and DLP and ED reductions were 35.6% than with MDCT (465.0 mGy * cm vs 732.3 mGy * cm and 6.5 mSv and 10.3 mSv; vs p < 0.0001). Concerning scan parameters, kVp and ET reductions were 12.7% and 69.4%, respectively (p < 0.0001); PF increase was 73.8% (p < 0.0001). In all vascular studies, DSCT, compared with MDCT, permitted to reduce CTDIvol from 43.5 to 70.6%; DLP and ED reductions were from 50.3 to 73.1%; kVp and ET decreases were from 10.7 to 32.5% and from 26.3 to 68.7%. PF increase was from 16.7 to 58.1% (all differences with p < 0.0001). CONCLUSIONS: In daily practice, CV examinations CTDI, DLP, ED, ET and TV were lower and PF was higher with 192 × 2-DSCT compared to 64-MDCT.

A phantom study for the comparison of different brands of computed tomography scanners and software packages for endovascular aneurysm repair sizing and planning.

Objectives Correct sizing of endoprostheses used for the treatment of abdominal aortic aneurysms is important to prevent endoleaks and migration. Sizing requires several steps and each step introduces a possible sizing error. The goal of this study was to investigate the magnitude of these errors compared to the golden standard: a vessel phantom. This study focuses on the errors in sizing with three different brands of computed tomography angiography scanners in combination with three reconstruction software packages. Methods Three phantoms with a different diameter, altitude and azimuth were scanned with three computed tomography scanners: Toshiba Aquilion 64-slice, Philips Brilliance iCT 256-slice and Siemens Somatom Sensation 64-slice. The phantom diameters were determined in the stretched view after central lumen line reconstruction by three observers using Simbionix PROcedure Rehearsal Studio, 3mensio and TeraRecon planning software. The observers, all novices in sizing endoprostheses using planning software, measured 108 slices each. Two senior vascular surgeons set the tolerated error margin of sizing on ±1.0 mm. Results In total, 11.3% of the measurements (73/648) were outside the set margins of ±1.0 mm from the phantom diameter, with significant differences between the scanner types (14.8%, 12.1%, 6.9% for the Siemens scanner, Philips scanner and Toshiba scanner, respectively, p-value = 0.032), but not between the software packages (8.3%, 11.1%, 14.4%, p-value = 0.141) or the observers (10.6%, 9.7%, 13.4%, p-value = 0.448). Conclusions It can be concluded that the errors in sizing were independent of the used software packages, but the phantoms scanned with Siemens scanner were significantly more measured incorrectly than the phantoms scanned with the Toshiba scanner. Consequently, awareness on the type of computed tomography scanner and computed tomography scanner setting is necessary, especially in complex abdominal aortic aneurysms sizing for fenestrated or branched endovascular aneurysm repair if appropriate the sizing is of upmost importance.

Radiation Dose Reduction With a Low-Tube Voltage Technique for Pediatric Chest Computed Tomographic Angiography Based on the Contrast-to-Noise Ratio Index.

INTRODUCTION: The aim of this study was to evaluate the radiation dose and image quality at low tube-voltage pediatric chest computed tomographic angiography (CTA) that applies the same contrast-to-noise ratio (CNR) index as the standard tube voltage technique. MATERIALS AND METHODS: Contrast-enhanced chest CTA scans of 100 infants were acquired on a 64-row multidetector computed tomography (MDCT) scanner. In the retrospective study, we evaluated 50 images acquired at 120 kVp; the image noise level was set at 25 Hounsfield units. In the prospective study, we used an 80-kVp protocol; the image noise level was 40 Hounsfield units because the iodine contrast was 1.6 times higher than on 120-kVp scans; the CNR was as in the 120-kVp protocol. We compared the CT number, image noise, CT dose index volume (CTDIvol), and the dose-length product on scans acquired with the 2 protocols. A diagnostic radiologist and a pediatric cardiologist visually evaluated all CTA images. RESULTS: The mean CTDIvol and the mean dose-length product were 0.5 mGy and 7.8 mGy-cm for 80- and 1.2 mGy and 20.8 mGy-cm for 120-kVp scans, respectively (P < .001). The mean CTDIvol was 42% lower at 80 kVp than at 120 kVp, and there was no significant difference in the visual scores assigned to the CTA images (P = .28). CONCLUSIONS: With the CNR index being the same at 80-kVp and 120-kVp imaging, the radiation dose delivered to infants subjected to chest CTA can be reduced without degradation of the image quality.

Dual-Source Single-Energy Multidetector CT Used to Obtain Multiple Radiation Exposure Levels within the Same Patient: Phantom Development and Clinical Validation.

Purpose To develop, in a phantom environment, a method to obtain multidetector computed tomographic (CT) data sets at multiple radiation exposure levels within the same patient and to validate its use for potential dose reduction by using different image reconstruction algorithms for the detection of liver metastases. Materials and Methods The American College of Radiology CT accreditation phantom was scanned by using a dual-source multidetector CT platform. By adjusting the radiation output of each tube, data sets at six radiation exposure levels (100%, 75%, 50%, 37.5%, 25%, and 12.5%) were reconstructed from two consecutive dual-source single-energy (DSSE) acquisitions, as well as a conventional single-source acquisition. A prospective, HIPAA-compliant, institutional review board-approved study was performed by using the same DSSE strategy in 19 patients who underwent multidetector CT of the liver for metastatic colorectal cancer. All images were reconstructed by using conventional weighted filtered back projection (FBP) and sinogram-affirmed iterative reconstruction with strength level of 3 (SAFIRE-3). Objective image quality metrics were compared in the phantom experiment by using multiple linear regression analysis. Generalized linear mixed-effects models were used to analyze image quality metrics and diagnostic performance for lesion detection by readers. Results The phantom experiment showed comparable image quality between DSSE and conventional single-source acquisition. In the patient study, the mean size-specific dose estimates for the six radiation exposure levels were 13.0, 9.8, 5.8, 4.4, 3.2, and 1.4 mGy. For each radiation exposure level, readers' perception of image quality and lesion conspicuity was consistently ranked superior with SAFIRE-3 when compared with FBP (P ≤ .05 for all comparisons). Reduction of up to 62.5% in radiation exposure by using SAFIRE-3 yielded similar reader rankings of image quality and lesion conspicuity when compared with routine-dose FBP. Conclusion A method was developed and validated to synthesize multidetector CT data sets at multiple radiation exposure levels within the same patient. This technique may provide a foundation for future clinical trials aimed at estimating potential radiation dose reduction by using iterative reconstructions. © RSNA, 2016 Online supplemental material is available for this article.

Is multidetector CT-based bone mineral density and quantitative bone microstructure assessment at the spine still feasible using ultra-low tube current and sparse sampling?

OBJECTIVE: Osteoporosis diagnosis using multidetector CT (MDCT) is limited to relatively high radiation exposure. We investigated the effect of simulated ultra-low-dose protocols on in-vivo bone mineral density (BMD) and quantitative trabecular bone assessment. MATERIALS AND METHODS: Institutional review board approval was obtained. Twelve subjects with osteoporotic vertebral fractures and 12 age- and gender-matched controls undergoing routine thoracic and abdominal MDCT were included (average effective dose: 10 mSv). Ultra-low radiation examinations were achieved by simulating lower tube currents and sparse samplings at 50%, 25% and 10% of the original dose. BMD and trabecular bone parameters were extracted in T10-L5. RESULTS: Except for BMD measurements in sparse sampling data, absolute values of all parameters derived from ultra-low-dose data were significantly different from those derived from original dose images (p<0.05). BMD, apparent bone fraction and trabecular thickness were still consistently lower in subjects with than in those without fractures (p<0.05). CONCLUSION: In ultra-low-dose scans, BMD and microstructure parameters were able to differentiate subjects with and without vertebral fractures, suggesting osteoporosis diagnosis is feasible. However, absolute values differed from original values. BMD from sparse sampling appeared to be more robust. This dose-dependency of parameters should be considered for future clinical use. KEY POINTS: • BMD and quantitative bone parameters are assessable in ultra-low-dose in vivo MDCT scans. • Bone mineral density does not change significantly when sparse sampling is applied. • Quantitative trabecular bone microstructure measurements are sensitive to dose reduction. • Osteoporosis subjects could be differentiated even at 10% of original dose. • Radiation exposure should be considered when comparing quantitative bone parameters.

Dual- versus Single-Energy CT-Angiography Imaging for Patients Undergoing Intracranial Aneurysm Repair.

BACKGROUND: The invasiveness and risk of thromboembolic complications of catheter angiography underline the need for alternative imaging modalities in patients following intracranial aneurysm (IA) repair. However, the overall image quality of existing noninvasive imaging modalities, such as single-energy CT angiography (SE-CTA), compromises its value in this respect. OBJECTIVE: We prospectively investigated the value of a novel dual-energy CTA (DE-CTA) scanner and algorithm for assessing the degree of occlusion and parent vessel patency in patients following IA repair. METHODS: A prospective cohort of 17 patients underwent DE-CTA imaging following surgical or endovascular IA repair. This dataset was matched with an identical historical cohort of 17 patients, who underwent IA repair and SE-CTA imaging. Beam-hardening artifacts, as a measure for objective imaging quality were analyzed based on the volume of a prolate ellipsoid, whereas subjective imaging quality at the IA site and corresponding parent vessels was rated by 2 independent neuroradiologists on a scale from 4 (excellent, no artifacts) to 1 (poor, severe artifacts). RESULTS: Objective DE-CTA image quality was markedly higher, compared to SE-CTA in patients undergoing surgical (0.77 ± 0.23 vs. 10.91 ± 1.88 mL, respectively; p < 0.001) or endovascular (32.36 ± 10.62 vs. 107.63 ± 24.51 mL, respectively; p = 0.026) IA repair. Subjective image quality for DE-CTA was significantly improved compared to SE-CTA in the surgical group but not in the endovascular group. The calculated dose values for DE-CTA in our study remain markedly below the legally required radiation dose limits. CONCLUSION: The imaging quality of DE-CTA, especially for patients undergoing surgical IA repair, is distinctly superior, compared to SE-CTA imaging. Therefore, DE-CTA may serve as a noninvasive alternative for assessing the IA occlusion rate and parent vessel patency.

Use of Synchrotron Radiation to Accurately Assess Cross-Sectional Area Reduction of the Aortic Branch Ostia Caused by Suprarenal Stent Wires.

PURPOSE: To compare in vivo the use of synchrotron radiation to computed tomography angiography (CTA) for the measurement of cross-sectional area (CSA) reduction of the aortic branch ostia caused by suprarenal stent-graft wires. METHODS: This study was performed with a Zenith stent-graft placed in a phantom of the human aorta to simulate treatment of abdominal aortic aneurysm. Synchrotron radiation scans were performed using beam energies between 40 and 100 keV and spatial resolution of 19.88 µm per pixel. CSA reduction of the aortic branch ostia by suprarenal stent wires was calculated based on these exposure factors and compared with measurements from CTA images acquired on a 64-row scanner with slice thicknesses of 1.0, 1.5, and 2.0 mm. RESULTS: Images acquired with synchrotron radiation showed <10% of the CSA occupied by stent wires when a single wire crossed a renal artery ostium and <20% for 2 wires crossing a renovisceral branch ostium. The corresponding areas ranged from 24% to 25% for a single wire and from 40% to 48% for double wires crossing the branch ostia when measured on CT images. The stent wire was accurately assessed on synchrotron radiation with a diameter between 0.38±0.01 and 0.53±0.03 mm, which is close to the actual size of 0.47±0.01 mm. The wire diameter measured on CT images was greatly overestimated (1.15±0.01 to 1.57±0.02 mm). CONCLUSION: CTA has inferior spatial resolution that hinders accurate assessment of CSA reduction. This experiment demonstrated the superiority of synchrotron radiation over CTA for more accurate assessment of aortic stent wires and CSA reduction of the aortic branch ostia.

Estimating Effective Dose of Radiation From Pediatric Cardiac CT Angiography Using a 64-MDCT Scanner: New Conversion Factors Relating Dose-Length Product to Effective Dose.

OBJECTIVE: The purpose of this study is to determine the conversion factors that enable accurate estimation of the effective dose (ED) used for cardiac 64-MDCT angiography performed for children. MATERIALS AND METHODS: Anthropomorphic phantoms representative of 1- and 10-year-old children, with 50 metal oxide semiconductor field-effect transistor dosimeters placed in organs, underwent scanning performed using a 64-MDCT scanner with different routine clinical cardiac scan modes and x-ray tube potentials. Organ doses were used to calculate the ED on the basis of weighting factors published in 1991 in International Commission on Radiological Protection (ICRP) publication 60 and in 2007 in ICRP publication 103. The EDs and the scanner-reported dose-length products were used to determine conversion factors for each scan mode. The effect of infant heart rate on the ED and the conversion factors was also assessed. RESULTS: The mean conversion factors calculated using the current definition of ED that appeared in ICRP publication 103 were as follows: 0.099 mSv · mGy-1 · cm-1, for the 1-year-old phantom, and 0.049 mSv · mGy-1 · cm-1, for the 10-year-old phantom. These conversion factors were a mean of 37% higher than the corresponding conversion factors calculated using the older definition of ED that appeared in ICRP publication 60. Varying the heart rate did not influence the ED or the conversion factors. CONCLUSION: Conversion factors determined using the definition of ED in ICRP publication 103 and cardiac, rather than chest, scan coverage suggest that the radiation doses that children receive from cardiac CT performed using a contemporary 64-MDCT scanner are higher than the radiation doses previously reported when older chest conversion factors were used. Additional up-to-date pediatric cardiac CT conversion factors are required for use with other contemporary CT scanners and patients of different age ranges.

The "Air in the CT X-ray Tube Oil" Artifact-Examples of the Quality Control Images and the Evaluation of Four Potential Clinical Patients' Head Computed Tomography Cases.

We present a newly reposted scanner-based artifact-with 4 potential patients' head computed tomography (CT) cases-the "Air in the CT X-ray Tube Oil" artifact with a 64-slice multidetector CT. This artifact mimics diseases, which cause hypodense findings in CT images. It can be difficult to notice in the clinical patient imaging but can be also very difficult to verify in quality control tests.

Influential Factors on the Evaluation of Adamkiewicz Artery Using a 320-Detector Row Computed Tomography Device.

BACKGROUND: Understanding the difference of Adamkiewicz artery (AKA) presentation in healthy and diseased subjects, and the influence of atherosclerotic factors prevalent in aortic disease patients, are important for aortic disease therapeutic planning. This study used a 320-detector row computed tomography (CT) device to examine the impact of clinical aspects of AKA identification in individuals with and without aortic disease. METHODS: Angio-CTs obtained from 115 patients were assessed and the individuals grouped according to the presence or absence of aortic disease. Datasets were analyzed using OsiriX software, and AKA was identified by three-dimensional multiplanar reconstruction. RESULTS: The group without aortic disease (Group A) comprised 32 (52.5%) men and 29 women, with a mean age of 53.7 ± 16.8 years. The group with aortic disease (Group B) comprised 31 (57.4%) men and 23 women, with a mean age of 64.8 ± 11.6 years. AKA was identified in 49 (80.3%) participants of Group A and 23 (42.6%) individuals of Group B (P ≤ 0.0001). In 53 cases (73.6%), AKA originated on the left side. AKA was mainly detected on the left side (73.6%), at the level of T10 to T12 (70%). Tobacco smokers, former smokers, and hypertensive patients had increased odds of having undetected AKA. CONCLUSIONS: Using the method described and a state of the art 320-detector row CT device, AKA was detected more frequently among individuals without aortic disease. Thus, aortic disease and atherosclerotic risk factors hindered AKA detection.

Comparison of radiation doses imparted during 128-, 256-, 384-multislice CT-scanners and cone beam computed tomography for intra- and perioperative cochlear implant assessment.

PURPOSE: To examine radiation-doses imparted during multislice (MSCT) and cone-beam computed-tomography (CBCT) for perioperative examination of cochlear-implant insertion. METHODS: Radiation-doses were assessed during standardized petrous-bone CT-protocols at different MSCT ((I) single-source CT-scanner Somatom-Definition-AS+, (II) 2nd generation of dual-source CT-scanner Somatom-Definition-Flash, (III) 3rd generation of dual-source CT-scanner Somatom-Force and at the CBCT Ziehm-Vision-RFD3D ((IV) (a) RFD-3D (Standard-modifier), (b) RFD-3D (Low-dose-modifier)). Image quality was examined by two radiologists appraising electrode-array placement, quality-control of cochlear-implant surgery and complications based on real patients' examinations (n=78). RESULTS: In MSCT-setting following radiation-doses were assessed (CTDIw; DLP): (I) 21.5mGy; 216mGycm; (II) 19.7mGy; 195mGycm; (III) 12.7mGy; 127mGycm; in the CBCT setting radiation doses were distributed as follows: (IV) (a) 1.9mGy; 19.4mGycm; (b) 1.2mGy; 12.9mGycm. Overall, image quality was evaluated as good for both, MSCT- and CBCT-examinations, with a good interrater reliability (r=0.81). CONCLUSION: CBCT bears considerable dose-saving potential for the perioperative examination of cochlear-implant insertion while maintaining adequate image quality.

Relationship between Carotid Computed Tomography Dual-Energy and Brain Leukoaraiosis.

BACKGROUND: The purpose of this study was to assess if there is a correlation between the carotid computed tomography (CT) Hounsfield unit (HU)-based plaque attenuation values measured using dual-energy CT (DECT) scanner and brain leukoaraiosis (LA). METHODS: Fifty consecutive patients (34 males, 16 females; mean age, 69 years; age range, 46-84 years) who underwent carotid CT and brain magnetic resonance imaging were included in the study. CT examinations were performed with a DECT scanner, and LA lesion volume quantification was performed using a semiautomated segmentation technique. RESULTS: We found an inverse statistically significant correlation between the HU-based carotid artery plaque attenuation and the LA lesion volume. Because of the presence of calcified plaques, a second model was calculated at low kiloelectron volt levels from 66 to 100 and 100 kV by taking into consideration the fatty and mixed plaques, and this further led to the associations between HU-based attenuation and LA volume in brain and vascular territories. CONCLUSIONS: The results of our study suggest that the associations between HU attenuation of the carotid artery plaques (with the exclusion of calcified plaques) and the volume of LA are emphasized at low keV energy levels.

Imaging the renal lesion with dual-energy multidetector CT and multi-energy applications in clinical practice: what can it truly do for you?

OBJECTIVE: Many fortuitously detected renal lesions are incompletely characterised at traditional MDCT imaging, thus posing daily challenges to radiologists and referring physicians. There is burgeoning evidence that dual-energy MDCT and multi-energy applications provide an added value over traditional MDCT imaging in renal lesion characterisation and throughput. This special report gives a vendor-neutral outlook on technical essentials, recommended protocols, high-yield clinical opportunities and reviews radiation dose aspects of dual-energy MDCT imaging and multi-energy applications in renal lesions. In addition to a guide on interpretative traps and emerging problems, we provide an update on new, potential imaging horizons. CONCLUSION: Dual-energy MDCT and multi-energy applications can facilitate the imaging interpretation and throughput of renal lesions. Conjointly with capitalisation on the benefits, familiarity with dual- and multi-energy data sets as well as continuous scrutiny of interpretative traps can be the keys to the successful implementation and enhanced clinical acceptance of this powerful technique in the imaging community. Continuous advances in hardware and computer interfaces are expected to pave the way for the further expansion of the application spectrum. KEY POINTS: • Optimal protocols must be adopted for leveraging dual-energy benefits in renal imaging. • Virtual monochromatic imaging can overcome renal cyst pseudoenhancement. • Iodine maps help to interpret renal lesions incompletely characterised at traditional MDCT. • Interpretative traps need to be weighed-up in dual-energy renal lesions imaging. • Technical advances are expanding the dual-energy applications spectrum for renal lesions imaging.