RESUMO
Here, we report a method for facile gram-scale synthesis of tetrahedrite (Cu12Sb4S13) nanoparticles (NPs) with high quality and good reproducibility. The obtained NPs had a well-defined tetrahedral shape with a mean edge length of â¼70 nm. We sintered the NPs by the hot press technique to fabricate a nanostructured pellet for thermoelectric measurements. The figure of merit (ZT) value of the pellet was 0.52 at 675 K, which was comparable with the ZT value of the non-nanostructured counterpart.
RESUMO
Two types of light-emitting electrochemical cells (LECs) are commonly distinguished, the polymer-based LEC (p-LEC) and the ionic transition metal complex-based LEC (iTMC-LEC). Apart from marked differences in the active layer constituents, these LEC types typically show operational time scales that can differ by many orders of magnitude at room temperature. Here, we demonstrate that despite these differences p-LECs and iTMC-LECs show current, light output, and efficacy transients that follow a universal shape. Moreover, we conclude that the turn-on time of both LEC types is dominated by the ion conductivity because the turn-on time exhibits the same activation energy as the ion conductivity in the off-state. These results demonstrate that both types of LECs are really two extremes of one class of electroluminescent devices. They also implicate that no fundamental difference exists between charge transport in small molecular weight or polymeric mixed ionic and electronic conductive materials. Additionally, it follows that the ionic conductivity is responsible for the dynamic properties of devices and systems using them. This likely extends to mixed ionic and electronic conductive materials used in organic solar cells and in a variety of biological systems.
RESUMO
Further study of our aerobic intermolecular cyclization of acrylic acid with 1-octene to afford α-methylene-γ-butyrolactones, catalyzed by the Pd(OCOCF(3))(2)/Cu(OAc)(2)â H(2)O system, has clarified that the accumulation of water generated from oxygen during the reaction causes deactivation of the Cu cocatalyst. This prevents regeneration of the active Pd catalyst and, thus, has a harmful influence on the progress of the cyclization. As a result, both the substrate conversion and product yield are efficiently improved by continuous removal of water from the reaction mixture. Detailed analysis of the kinetic and spectroscopic measurements performed under the condition of continuous water removal demonstrates that the cyclization proceeds in four steps: 1)â equilibrium coordination of 1-octene to the Pd acrylate species, 2)â Markovnikov-type acryloxy palladation of 1-octene (1,2-addition), 3)â intramolecular carbopalladation, and 4)â ß-hydride elimination. Byproduct 2-acryloxy-1-octene is formed by ß-hydride elimination after step 2). These cyclization steps fit the Michaelis-Menten equation well and ß-hydride elimination is considered to be a rate-limiting step in the formation of the products. Spectroscopic data agree sufficiently with the existence of the intermediates bearing acrylate (Pd-O bond), η(3)-C(8)H(15) (Pd-C bond), or C(11)H(19)O(2) (Pd-C bond) moieties on the Pd center as the resting-state compounds. Furthermore, not only Cu(II), but also Cu(I), species are observed during the reaction time of 2-8â h when the reaction proceeds efficiently. This result suggests that the Cu(II) species is partially reduced to the Cu(I) species when the active Pd catalytic species are regenerated.
RESUMO
Direct energy conversion of heat into electricity using thermoelectric materials is an attractive solution to help address global energy issues. Developing novel materials composed of earth-abundant and nontoxic elements will aid progress toward the goal of sustainable thermoelectric materials. In this study, we chemically synthesized Cu-Zn-Sn-S nanocrystals and fabricated a Cu3ZnSnS5-y thermoelectric material using nanocrystals as building blocks. The figure-of-merit (ZT) value of the Cu3ZnSnS5-y material was found to be 0.39 at 658 K. We substituted Zn with Al in the Cu3ZnSnS5-y system to form Cu3Zn1-x Al x SnS5-y (x = 0.25, 0.5, 0.75, and 1) to lower the lattice thermal conductivity of the resulting materials. Complete substitution of Al for Zn substantially decreased the lattice thermal conductivity and dramatically increased the electrical conductivity of the material. However, the ZT value could not be significantly enhanced, which could be primarily attributed to the high carrier thermal conductivity. These results highlight the production of Cu3Zn1-x Al x SnS5-y thermoelectric materials and unveil the scope for improvement of ZT values by altering transport properties.
RESUMO
Solution-processed, salt-containing, blue and orange light-emitting layers lead to efficient white light-emitting devices when arranged in a tandem configuration separated by a thin metal layer.
RESUMO
Light-emitting electrochemical cells (LECs) consists of a thin film of an ionic organic semiconductor sandwiched between two electrodes. Because of the large density of ions, LECs are often reported to perform independently on the electrodes work function. Here we use metal oxides as charge injection layers and demonstrate that, although electroluminescence is observed independently of the electrodes used, the device performances are strongly dependent on the choice of the interface materials. Relying on metal oxide charge injection layers, such hybrid devices are of interest for real lighting applications and could pave the way for new efficient, stable, low-cost lighting sources.