Energy potential and alternative usages of biogas and sludge from UASB reactors: case study of the Laboreaux wastewater treatment plant.

This work assessed the energy potential and alternative usages of biogas and sludge generated in upflow anaerobic sludge blanket reactors at the Laboreaux sewage treatment plant (STP), Brazil. Two scenarios were considered: (i) priority use of biogas for the thermal drying of dehydrated sludge and the use of the excess biogas for electricity generation in an ICE (internal combustion engine); and (ii) priority use of biogas for electricity generation and the use of the heat of the engine exhaust gases for the thermal drying of the sludge. Scenario 1 showed that the electricity generated is able to supply 22.2% of the STP power demand, but the thermal drying process enables a greater reduction or even elimination of the final volume of sludge to be disposed. In Scenario 2, the electricity generated is able to supply 57.6% of the STP power demand; however, the heat in the exhaust gases is not enough to dry the total amount of dehydrated sludge.

Exceptional performance of Fe@carbon-rich nanoparticles prepared via hydrothermal carbonization of oil mill wastes for H2S removal.

Carbon-encapsulated iron oxide nanoparticles (CE-nFe) have been obtained from an industrial waste (oil mill wastewater-OMW, as a carbonaceous source), and using iron sulfate as metallic precursor. In an initial step, the hydrochar obtained has been thermally activated under an inert atmosphere at three different temperatures (600 °C, 800 °C and 1000 °C). The thermal treatment promotes the development of core-shell nanoparticles, with an inner core of α-Fe/Fe3O4, surrounded by a well-defined graphite shell. Temperatures above 800 °C are needed to promote the graphitization of the carbonaceous species, a process promoted by iron nanoparticles through the dissolution, diffusion and growth of the carbon nanostructures on the outer shell. Breakthrough column tests show that CE-nFe exhibit an exceptional performance for H2S removal with a breakthrough capacity larger than 0.5-0.6 g H2S/gcatalyst after 3 days experiment. Experimental results anticipate the crucial role of humidity and oxygen in the adsorption/catalytic performance. Compared to some commercial samples, these results constitute a three-fold increase in the catalytic performance under similar experimental conditions.

New methods to remove volatile organic compounds from post-consumer plastic waste.

While the annual European demand for polyolefins is 25 million tonnes, only 3 million tonnes of recycled polyolefins find their place in the market, despite collecting 15 million tonnes of post-consumer polyolefins every year. Brand owners of care products are showing their interest in using post-consumer recycled plastics for their packaging. However, there is a general concern in using these materials, as recycled polymers can contain unwanted substances that may expose the consumer to health risks or make the packaging unattractive. Accordingly, the presence of these contaminants narrows the market opportunity of recycled plastics to applications with low-quality requirements and in which the product is not in direct contact with the consumer. Though mechanical recycling is the most widespread solution presents limitations in terms of decontamination, as only superficial substances are removed. Thereby, the volatile organic compounds (VOCs) migrated to the polymer matrix remain inside. Consequently, there is a need to find a solution to purify recycled plastics and increase their market share. This study focuses on removing VOCs from post-consumer recycled HDPE through two innovative methods applied for the first time in this field, steam stripping and polyethylene glycol (PEG) extraction. The methodology implemented to analyze the volatile organic compounds in HDPE was HS-SPME-GC/MS. Both methods showed a decrease above 70% in the VOCs content compared to extrusion-degassing. Moreover, these were compared to hot air stripping, a new technology developed at an industrial scale for the removal of VOCs. As a result, steam stripping improved efficiency in reducing the overall VOCs compared to hot air stripping. The PEG extraction method lowered the volatile polar compounds further than using hot air stripping. Additionally, none of these technologies modified the HDPE melting flow index.

Non-intentionally added substances (NIAS) in recycled plastics.

The demand for high quality recycled polymers in the European plastic industry is on the increase, likely due to the EU's Plastic Strategy intended to implement the circular economy model in this sector. The problem is that there is not enough recycled plastic in the market. In terms of volume, post-consumer plastic waste could be key to meet the current and future demand. Nevertheless, a high level of contamination originated during the product's life cycle restricts its use. The first step to change this must be identifying the undesired substances in post-consumer plastics and performing an effective risk assessment. The acquired knowledge will be fundamental for the development of innovative decontamination technologies. In this study, 134 substances including volatile and semi-volatile compounds have been identified in recycled LDPE and HDPE from domestic waste. Headspace and solvent extraction followed by GC/MS were used. The possible origin of each substance was studied. The main groups were additives, polymer and additives breakdown products, and contamination from external sources. The results suggest that recycled LDPE contains a broader number of additives and their degradation products. Some of them may cause safety concerns if reused in higher added value applications. Regarding recycled HDPE, the contaminants from the use phase are predominant creating problems such as intense odors. To reduce the number of undesired substances, it is proposed to narrow the variety of additives used in plastic manufacturing and to opt for separate waste collection systems to prevent cross-contamination with organic waste.

Centrifugal dewatering performance in plastic films recycling.

Dewatering of plastic films is a highly energy-consuming recycling operation that largely affects the quality of the recycled product. Despite the importance of good drying, this operation has not been studied at laboratory or pilot plant scale. In this work, the mechanical dewatering of blown film grade high density polyethylene has been assessed by using a laboratory centrifuge. It is suggested that a plastic cake is formed under the centrifugal forces similar to the sludge cake after the filtration process. The water is retained within the plastic cake due to three phenomena: free water within the cake pores and voids, water maintained by capillarity (superficial and pendular) and water trapped due to the tortuosity of the plastic mass. The total moisture is a sum of an equilibrium moisture and a transient moisture. The equilibrium moisture depends on the centrifugal force (G) but it is independent of time. Conversely, the transient moisture is reliant on both the G-force and the centrifugation time. The experimental results showed that an optimum side length exists. The moisture content is minimized when the flake side lies between 1 and 2 cm. Finally, it has been found that the moisture content is a function of the plastic surface. Hence, the specific moisture content (the mass of water per total plastic surface) should be calculated to compare films with uneven thickness or made of different materials. In sum, the outcomes of this study may be fundamental for the further and more extensive research into the plastic films dewatering processes.

Plastic flexible films waste management - A state of art review.

Plastic flexible films are increasingly used in many applications due to their lightness and versatility. In 2014, the amount of plastic films represented 34% of total plastic packaging produced in UK. The flexible film waste generation rises according to the increase in number of applications. Currently, in developed countries, about 50% of plastics in domestic waste are films. Moreover, about 615,000 tonnes of agricultural flexible waste are generated in the EU every year. A review of plastic films recycling has been conducted in order to detect the shortcomings and establish guidelines for future research. This paper reviews plastic films waste management technologies from two different sources: post-industrial and post-consumer. Clean and homogeneous post-industrial waste is recycled through closed-loop or open-loop mechanical processes. The main differences between these methods are the quality and the application of the recycled materials. Further research should be focused on closing the loops to obtain the highest environmental benefits of recycling. This could be accomplished through minimizing the material degradation during mechanical processes. Regarding post-consumer waste, flexible films from agricultural and packaging sectors have been assessed. The agricultural films and commercial and industrial flexible packaging are recycled through open-loop mechanical recycling due to existing selective waste collection routes. Nevertheless, the contamination from the use phase adversely affects the quality of recycled plastics. Therefore, upgrading of current washing lines is required. On the other hand, household flexible packaging shows the lowest recycling rates mainly because of inefficient sorting technologies. Delamination and compatibilization methods should be further developed to ensure the recycling of multilayer films. Finally, Life Cycle Assessment (LCA) studies on waste management have been reviewed. A lack of thorough LCA on plastic films waste management systems was identified.

Pollutant content in marine debris and characterization by thermal decomposition.

Marine debris (MDs) produces a wide variety of negative environmental, economic, safety, health and cultural impacts. Most marine litter has a very low decomposition rate (plastics), leading to a gradual accumulation in the coastal and marine environment. Characterization of the MDs has been done in terms of their pollutant content: PAHs, ClBzs, ClPhs, BrPhs, PCDD/Fs and PCBs. The results show that MDs is not a very contaminated waste. Also, thermal decomposition of MDs materials has been studied in a thermobalance at different atmospheres and heating rates. Below 400-500K, the atmosphere does not affect the thermal degradation of the mentioned waste. However, at temperatures between 500 and 800K the presence of oxygen accelerates the decomposition. Also, a kinetic model is proposed for the combustion of the MDs, and the decomposition is compared with that of their main constituents, i.e., polyethylene (PE), polystyrene (PS), polypropylene (PP), nylon and polyethylene-terephthalate (PET).

Analysis of organic pollutants in sewage sludges from the Valencian community (Spain).

Seventeen sewage sludges were studied to analyse, with the minimum number of steps, the organic pollutants that the European Union proposes to be controlled for land application. The compounds determined were a selection of polycyclic aromatic hydrocarbons (PAHs); a selection of polychlorinated biphenyls (PCBs); di(2-ethylhexyl)phthalate (DEHP); nonylphenolic compounds, including nonylphenol (NP) and nonylphenol ethoxylates with 1 and 2 ethoxy groups (NP1EO + NP2EO); extractable organic halides (EOX); and linear alkylbenzene sulphonates (LAS) with an alkylic chain of 10 to 13 carbon atoms. The results were compared with the proposed regulatory limit values, and it was observed that NP + NP1EO + NP2EO and LAS exceeded the maximums in most samples, and DEHP exceeded some of them, whereas PAHs, PCBs, and EOX almost always went beyond the limits. The values obtained are similar to those from other countries, and it can be said that it is difficult to comply with the limits for NP + NP1EO + NP2EO and LAS in many of them, although this latter parameter was not considered in the study carried out by Leschber (2004) concerning the toxicity of sewage sludge. Statistical multivariant analysis was used to look for some relationship between the results of pollutants and the characteristics of the samples, and it was found that the ratio of NP1EO + NP2EO to NP was related to sludge treatment at the sewage plant. At the same time, it was seen that the higher values of organic pollutants belonged to digested sludges.

De novo synthesis of PCDD/F by thermogravimetry.

On the basis of laboratory experiments with model mixtures, the steps in the de novo synthesis of halogenated compounds were studied. The study was performed using a thermobalance to evaluate the temperature of the maximum rate and the kinetics of the decomposition of the materials in the presence of air. The effect of the presence of CuCl2 and CuO with an atmosphere of HCl was studied. Analysis of the volatiles and solids after combustion in a horizontal furnace confirms the presence of organochloride compounds (including PCDD/F) at various temperatures. With the procedure that we followed, combustion is separated from pyrolysis, and it is possible to analyze the essential factors involved in the combustion process.

Caudal deficiency and asplenia anomalies in sibs.

The caudal deficiency and asplenia anomalies have been described separately in children. Two sibs with these two entities are described. Only another similar case, with caudal deficiency and polysplenia anomalies was found in the literature. It is possible that this association could be a new syndromic entity. An autosomal recessive mode of inheritance is suggested.

[Primary peptic ulcer in childhood: apropos of 16 cases]. / Ulcera péptica primaria en la infancia: a propósito de 16 casos.

We report a retrospective review of primary peptic ulcer disease in 16 children, 8 boys and 8 girls between 2 and 14 years of age, seen at our hospital over a 4 years and 4 months period. Endoscopy was realized in all children and revealed 7 duodenal ulcers (DU) and 11 gastric ulcers (GU) (two patients had both locations). At the initial diagnosis 5 patients were less than 6 years old with a ratio GU/DU of 4:1; in the other patients this ratio was 1:1. In children with duodenal ulcer 56.5% of them had positive family history. The commonest presenting symptoms were abdominal pain (87.5%) and acute gastrointestinal bleeding (68.7%). The follow-up period ranged from 2 to 52 months; in 13 cases follow-up was more than 1 year. Four patients (3 DU and 1 GU) older than 6 years recurred.