Defect Engineering in Metal-Organic Frameworks Towards Advanced Mixed Matrix Membranes for Efficient Propylene/Propane Separation.

Highly permselective and durable membrane materials have been sought for energy-efficient C3 H6 /C3 H8 separation. Mixed-matrix membranes (MMMs) comprising a polymer matrix and metal-organic frameworks (MOFs) are promising candidates for this application; however, rational matching of filler-matrix is challenging and their separation performances need to be further improved. Here, we propose a novel strategy of "defect engineering" in MOFs as an additional degree of freedom to design advanced MMMs. MMMs incorporated with defect-engineered MOFs exhibit exceptionally high C3 H6 permeability and maintained C3 H6 /C3 H8 selectivity, especially with enhanced stability under industrial mixed-gas conditions. The gas transport, sorption, and material characterizations reveal that the defect sites in MOFs provide the resulting MMMs with not only ultrafast diffusion pathways but also favorable C3 H6 sorption by forming complexation with unsaturated open metal sites, confirmed by in situ FT-IR studies. Most importantly, the concept is also valid for different polymer matrices and gas pairs, demonstrating its versatile potential in other fields.

On the photophysicochemical properties of selected fluoroquinolones: solvatochromic and fluorescence spectroscopy study.

The photophysicochemical properties of selected fluoroquinolones in different solvents of various physical properties, including polarity and hydrogen bonding ability, were investigated using steady state fluorescence spectroscopy. The solvent-dependant fluorescence emission spectra of selected fluoroquinolones, namely ciprofloxacin (CIPR) and enrofloxacin (ENRO), were employed to gain insights concerning its photophysicochemical properties of interests. Interestingly, fluorescence spectra of the selected drugs exhibited structured emission spectra in nonpolar solvents such as hexane, whereas unstructured spectra were observed in more polar solvents such as alcohols and water. Also, a notable bathochromic shift in λ(max)(em) was observed in fluorescence spectra of both drugs with increasing solvent polarity that resulted in biphasic behavior upon applying the Lippert-Mataga correlation that correspond to general and specific solvent effects. Applying the Lippert-Mataga correlation to the fluorescence spectra of CIPR and ENRO in various solvents was employed to estimate the dipole moment difference between the ground and excited states of them, Δµ(µ(e) - µ(g)), where obtained results revealed the values of 9.4 and 16.2 Debye for the LE and ICT states of ENRO, respectively, and 8.0 and 16.2 Debye for the LE and ICT states of CIPR, respectively. Multiple linear regression analysis (MLRA) based on Kamlet-Taft equating was applied against absorption frequency (ν(abs)), emission frequency (ν(em)), Stokes shift (∆ν), and fluorescence quantum yield (Φ(f)), where obtained results revealed excellent correlation (R: 0.916-0.966) that are consistent with other results considering the effect of solvent polarizability, hydrogen bonding ability, and viscosity on the photophysicochemical properties of the studied fluoroquinolones.

Finely Tuned Submicroporous Thin-Film Molecular Sieve Membranes for Highly Efficient Fluid Separations.

Polymeric membranes with increasingly high permselective performances are gaining a significant role in lowering the energy burden and improving the environmental sustainability of complex chemical separations. However, the commercial deployment of newly designed materials with promising intrinsic properties for fluid separations has been stalled by challenges associated with fabrication and scale up of low-cost, high-performance, defect-free thin-film composite (TFC) membranes. Here, a facile method to fabricate next-generation TFC membranes using a bridged-bicyclic triptycene tetra-acyl chloride (Trip) building block with a large fraction of finely tuned structural submicroporosity (pore size < 4 Å) is demonstrated. The TFCs exhibit superb potential for removal of small (≈200 g mol-1 ) organic microcontaminants from organic solvent streams by showing both improved rejection and permeance in organic systems compared to current state-of-the-art commercial membranes. The TFCs also display unprecedented properties for desalination applications with performance located far above the current water permeance/sodium chloride rejection trendline. The strategy of using highly contorted triptycene building blocks with well-defined interconnected internal free volume elements establishes a scalable, generalized approach to fabricate highly selective, submicroporous TFC membranes for a wide variety of challenging energy-intensive fluid separations.

Experimental Mixed-Gas Permeability, Sorption and Diffusion of CO2-CH4 Mixtures in 6FDA-mPDA Polyimide Membrane: Unveiling the Effect of Competitive Sorption on Permeability Selectivity.

The nonideal behavior of polymeric membranes during separation of gas mixtures can be quantified via the solution-diffusion theory from experimental mixed-gas solubility and permeability coefficients. In this study, CO2-CH4 mixtures were sorbed at 35 °C in 4,4'-(hexafluoroisopropylidene)diphthalic dianhydride (6FDA)-m-phenylenediamine (mPDA)-a polyimide of remarkable performance. The existence of a linear trend for all data of mixed-gas CO2 versus CH4 solubility coefficients-regardless of mixture concentration-was observed for 6FDA-mPDA and other polymeric films; the slope of this trend was identified as the ratio of gas solubilities at infinite dilution. The CO2/CH4 mixed-gas solubility selectivity of 6FDA-mPDA and previously reported polymers was higher than the equimolar pure-gas value and increased with pressure from the infinite dilution value. The analysis of CO2-CH4 mixed-gas concentration-averaged effective diffusion coefficients of equimolar feeds showed that CO2 diffusivity was not affected by CH4. Our data indicate that the decrease of CO2/CH4 mixed-gas diffusion, and permeability selectivity from the pure-gas values, resulted from an increase in the methane diffusion coefficient in mixtures. This effect was the result of an alteration of the size sieving properties of 6FDA-mPDA as a consequence of CO2 presence in the 6FDA-mPDA film matrix.

Synthesis and Gas-Permeation Characterization of a Novel High-Surface Area Polyamide Derived from 1,3,6,8-Tetramethyl-2,7-diaminotriptycene: Towards Polyamides of Intrinsic Microporosity (PIM-PAs).

A triptycene-based diamine, 1,3,6,8-tetramethyl-2,7-diamino-triptycene (TMDAT), was used for the synthesis of a novel solution-processable polyamide obtained via polycondensation reaction with 4,4'-(hexafluoroisopropylidene)bis(benzoic acid) (6FBBA). Molecular simulations confirmed that the tetrasubstitution with ortho-methyl groups in the triptycene building block reduced rotations around the C⁻N bond of the amide group leading to enhanced fractional free volume. Based on N2 sorption at 77 K, 6FBBA-TMDAT revealed microporosity with a Brunauer⁻Emmett⁻Teller (BET) surface area of 396 m² g-1; to date, this is the highest value reported for a linear polyamide. The aged 6FBBA-TMDAT sample showed moderate pure-gas permeabilities (e.g., 198 barrer for H2, ~109 for CO2, and ~25 for O2) and permselectivities (e.g., αH2/CH4 of ~50) that position this polyamide close to the 2008 H2/CH4 and H2/N2 upper bounds. CO2⁻CH4 mixed-gas permeability experiments at 35 °C demonstrated poor plasticization resistance; mixed-gas permselectivity negatively deviated from the pure-gas values likely, due to the enhancement of CH4 diffusion induced by mixing effects.

High-performance membranes from polyimides with intrinsic microporosity.

Membranes with high permeability to gases are formed from polyimides with rigid backbones that incorporate a spiro-centre. A route to this new range of high-free-volume polyimides is demonstrated, and exceptional performance is obtained for a polymer containing a dimethyl binaphthyl unit.

Synthesis of Highly Gas-Permeable Polyimides of Intrinsic Microporosity Derived from 1,3,6,8-Tetramethyl-2,7-diaminotriptycene.

A simple synthetic route to a novel sterically hindered triptycene-based diamine, 1,3,6,8-tetramethyl-2,7-diaminotriptycene (TMDAT), and its use in the preparation of high molecular weight polyimides of intrinsic microporosity (PIM-PIs) are reported. The organosoluble TMDAT-derived polyimides displayed high Brunauer-Emmett-Teller surface areas ranging between 610 and 850 m2 g-1 and demonstrated excellent thermal stability of up to 510 °C. Introduction of the rigid three-dimensional paddlewheel triptycene framework and the tetramethyl-induced restriction of the imide bond rotation resulted in highly permeable polyimides with moderate gas-pair selectivity. The best performing polyimide made from TMDAT and a triptycene-based dianhydride showed gas transport properties located between the 2008 and 2015 polymer permeability/selectivity trade-off curves with H2 and O2 permeabilities of 2858 and 575 barrer combined with H2/N2 and O2/N2 selectivities of 24 and 4.8, respectively, after 200 days of physical aging.

A triptycene-based polymer of intrinsic microposity that displays enhanced surface area and hydrogen adsorption.

A novel triptycene-based polymer of intrinsic microporosity (Trip-PIM) displays enhanced surface area (1065 m2 g(-1)) and reversibly adsorbs 1.65% hydrogen by mass at 1 bar/77 K and 2.71% at 10 bar/77 K.

Polymers of intrinsic microporosity (PIMs): robust, solution-processable, organic nanoporous materials.

Microporous materials can be derived directly from soluble polymers whose randomly contorted shapes prevent an efficient packing of the macromolecules in the solid state.

Energy-efficient hydrogen separation by AB-type ladder-polymer molecular sieves.

Increases in hydrogen selectivity of more than 100% compared with the most selective ladder polymer of intrinsic microporosity (PIM) reported to date are achieved with self-polymerized A-B-type ladder monomers comprising rigid and three-dimensional 9,10-dialkyl-substituted triptycene moieties. The selectivities match those of materials commercially employed in hydrogen separation, but the gas permeabilities are 150-fold higher. This new polymer molecular sieve is also the most selective PIM for air separation.

Polymers of intrinsic microporosity (PIMs): bridging the void between microporous and polymeric materials.

Novel types of microporous material are required for chemoselective adsorptions, separations and heterogeneous catalysis. This concept article describes recent research directed towards the synthesis of polymeric materials that possess microporosity that is intrinsic to their molecular structures. These polymers (PIMs) can exhibit analogous behaviour to that of conventional microporous materials, but, in addition, may be processed into convenient forms for use as membranes. The excellent performance of these membranes for gas separation and pervaporation illustrates the unique character of PIMs and suggests immediate technological applications.