Vertical root fracture detection with cone-beam computed tomography in Biodentine™ filled teeth.

PURPOSE: This study aimed to evaluate the accuracy of detecting vertical root fractures in Biodentine™-filled teeth using the Promax 3Dmax cone-beam computed tomography (CBCT) unit compared to periapical radiographs. It tested hypotheses regarding CBCT's diagnostic superiority in non-root-filled and Biodentine™-root-filled maxillary central incisors and assessed the impact of smaller field of view and lower intensity settings on detection accuracy. MATERIALS AND METHODS: Extracted maxillary incisors were divided into groups based on fracture status and root filling material, then placed in a Thiel-embalmed skull to simulate clinical conditions. The teeth were imaged using periapical radiographs and the CBCT unit under different settings. Fracture thickness was measured with microcomputed tomography for accuracy benchmarking. Multiple observers assessed the images, and statistical analyses were conducted to evaluate diagnostic performance. RESULTS: Intra-rater reliabilities of consensus scores ranged from good to very good. Specificities were generally higher than sensitivities across all imaging modalities, but sensitivities remained constantly low. None of the Area Under the Curve scores exceeded 0.6, indicating poor overall accuracy for all imaging modalities. Paired comparisons of the area differences under Receiver Operator Characteristic curves revealed no significant differences between the CBCT and periapical radiograph techniques for detecting vertical root fractures in either Biodentine™-filled or non-root-filled teeth. CONCLUSIONS: There was no significant accuracy improvement of the current CBCT device (Promax 3Dmax, Planmeca, Finland) over periapical radiographs in detecting small vertical root fractures in both non-root-filled and Biodentine™-root-filled maxillary central incisors. A smaller field of view with lower intensity did not enhance detection accuracy. These results highlight the challenges in accurately detecting small VRFs, emphasizing the need for further research and technological advancements in this domain.

A controlled study on the diagnostic accuracy of panoramic and peri-apical radiography for detecting furcation involvement.

BACKGROUND: The aims of this study were (1) to determine the accuracy, sensitivity, and specificity of panoramic and peri-apical radiographs in diagnosing furcation involvement, as well as (2) to evaluate the possible impact of clinical experience on these diagnostic parameters. METHODS: An existing radiographic dataset of periodontitis patients requiring implant surgery was retrospectively examined for furcation involvement. Criteria for inclusion were the presence of a CBCT, panoramic and peri-apical radiograph of the site of interest within a one-year time frame. All furcation sites were classified using the CBCT, which was considered as the gold standard, according to Hamp's index (1975). Ten experienced examiners and 10 trainees were asked to assess furcation involvement for the same defects using only the corresponding panoramic and peri-apical radiographs. Absolute agreement, Cohen's weighted kappa, sensitivity, specificity and ROC-curves were analyzed. RESULTS: The study sample included 60 furcation sites in 29 multi-rooted teeth from 17 patients. On average, 20/60 furcations were correctly classified according to the panoramic radiographs, corresponding to a weighted kappa score of 0.209, indicating slight agreement. Similarly, an average of 19/60 furcations were correctly classified according to the peri-apical radiographs, corresponding to a weighted kappa score of 0.211, also indicating slight agreement. No significant difference between panoramic and peri-apical radiography was found (P = 0.903). When recategorizing FI Grades into 'no to limited FI' (FI Grade 0 and I) and 'advanced FI' (FI Grade II and III), the panoramic and peri-apical radiography showed low sensitivity (0.558 and 0.441, respectively), yet high specificity (0.791 and 0.790, respectively) for identifying advanced FI. The ROC-curves for the panoramic and peri-apical radiographs were 0.79 and 0.69 respectively. No significant difference was found between experienced periodontists and trainees (P = 0.257 versus P = 0.880). CONCLUSION: Panoramic and peri-apical radiography are relevant tools in the diagnosis of FI and provide high specificity. Ideally, they are best used in combination with furcation probing, which shows high sensitivity. Furthermore, clinical experience does not seem to improve the accuracy of a radiological diagnosis of furcation sites. TRIAL REGISTRATION: Patient radiographic datasets were retrospectively analyzed.

Analgesia (mis)usage on a dental emergency service: a patient survey.

OBJECTIVES: Analgesics are one of the most frequently used medicines. Self-medication and misuse have been described in the literature. The purpose of this study was to document analgesic (mis)use in a population seeking emergency dental treatment. MATERIAL AND METHODS: Patients consulting a dental emergency service were randomly asked to complete a questionnaire on analgesic use, knowledge and information on the analgesics and on their pain history. A photobook was used as an aid to identify products used. Descriptive statistics were combined with chi-square and Mann-Whitney U testing. RESULTS: Ninety-eight patients were included. Acetaminophen (69.4%) and ibuprofen (65.3%) were the most frequently used products. Nearly half of the subjects (43.9%) combined at least two analgesics. Although 42.9% of subjects were aware of the maximum daily dose, 62.2% of the subjects exceeded this limit, specifically 76.6% of subjects using ibuprofen and 32.4% of subjects using acetaminophen overdosing. Females overdosed significantly more than males. Ingestion on medical advice did not affect the overdose rates significantly. No significant relation was found between the absence of knowledge on the maximum daily dose and actual overdosing. No higher pain reduction was found in patients overdosing analgesics. The average number of days patients experienced pain before consulting the emergency unit was 12. A significant relation was found between the lag time and overdosing. CONCLUSIONS: A large portion of the patients overdosed analgesics. Even prior medical advice did not reduce significantly overdose rates. CLINICAL RELEVANCE: Dentists treating emergency cases clearly need to be aware of the high risk and high rates of overdosing analgesics in their patients.

Proof of Concept of a New 3D-Guided System for a Single Implant Overdenture in the Mandible: An In Vitro Study.

PURPOSE: To evaluate the precision and efficiency of a novel guide system for single implant placement in the mandibular symphyses and to evaluate whether the outcome is affected by the level of operator experience. MATERIALS AND METHODS: A total of 90 implants were placed in three different mandibular cast types (Cawood and Howell class III, IV, and V). For each model, a complete denture was 3D printed. A polyether ether ketone rail with a guide sleeve was embedded in the middle of the denture. To determine the ideal implant position, the sleeve could be moved in a buccolingual direction. Adjustment of implant angulation was possible, and an angle correction of 0, 12, or 24 degrees was available. A total of 30 clinicians were divided into three groups: group 1 (experienced, n = 10), group 2 (beginner, n = 10), and group 3 (inexperienced, n = 10). Each clinician was asked to plan and perform a guided flapless implant placement in the mandibular symphysis. Two preoperative CBCT scans were taken; the first was to verify the planning, and the second was to adjust the planning if needed. Finally, a postoperative CBCT scan was taken to compare the planning to the final implant position. RESULTS: Based on the first CBCT, the clinicians adjusted their planning by an average of 1.66 ± 1.65 mm coronally, 2.41 ± 2.44 mm apically, and by a mean angular correction of 6.08 ± 0.77 degrees. After implant placement, the mean deviation from the planned implant position was 0.87 ± 0.58 mm at the coronal aspect and 0.98 ± 0.64 mm at the apical aspect. The mean angular deviation was 6.05 ± 0.71 degrees. Overall, there were no significant differences in coronal and apical deviation (P > .05) based on the level of experience. In terms of angulation, a significant difference was found in both planning (P = .049) and placement (P = .038) between beginners and experienced clinicians. CONCLUSIONS: Guided implant placement of a single implant in the mandibular symphysis using a removable denture with guide sleeve had an acceptable level of accuracy. Clinicians with limited experience spent more time on the procedure, resulting in less angular deviation during implant planning and placement compared to experienced clinicians.

Effect of radiation dose on the prevalence of apical periodontitis--a dosimetric analysis.

OBJECTIVES: The objective of this study is to analyse the effect of the radiation dose of oral radiotherapy for cancer on the presence of apical periodontitis in patients without dental pre-screening or specific preventive measures. MATERIALS AND METHODS: All selected patients had been diagnosed with cancer in the head and neck region and presented in the dental clinic post radiotherapy with side effects (mainly radiation caries). The panoramic radiographs of these patients were examined for several parameters, including tooth decay and apical periodontitis. The total radiation dose per tooth was determined. RESULTS: A total of 36 patient files were included, which accounted for 628 teeth to be scored. Tooth decay was present in 88.2% of teeth. Radiographic signs of apical periodontitis were found in 9.1% of the teeth. Teeth with apical periodontitis had significantly more caries present. The radiation dose was significantly higher for teeth with apical periodontitis (37.2 vs. 24.9 Gy). Binary logistic regression found the radiation dose to be the only explanatory variable in the presence of apical periodontitis. CONCLUSIONS: This study found that in zones with higher radiation dose, inflammation of the jawbone due to bacterial infection of the root canal is more likely to develop. This is probably due to bone changes post radiotherapy. CLINICAL RELEVANCE: An increase of this prevalance of apical periodontitis in irradiated bone found in this study needs to be taken into account in the dental evaluation before the start of radiotherapy.

A Completely Digital Workflow for Nanoceramic Endocrowns: A 5-Year Prospective Study.

PURPOSE: To evaluate the success of monolithic endocrowns fabricated using a digital workflow. MATERIALS AND METHODS: Twenty-three patients requiring restoration of devitalized molars or premolars were included in the study. The preparation was scanned using an intraoral scanner (Cerec Bluecam, Dentsply Sirona), and a monolithic restoration was made from a nanoparticle resin-based hybrid composite (#10 Cerasmart [CS]; #10 Lava Ultimate [LU], 3M Espe) or a polymer-infiltrated ceramic (#10 Vita Enamic [VE]). At the time of placement and after 6 months, 1 year, and 5 years of function, radiographs were taken to evaluate the marginal integrity of the restorations, and clinical pictures were taken to assess the quality of the restoration using the USPHS criteria. RESULTS: After 5 years, the restorative success rate was 70.8%, the restorative survival rate was 87.5%, and the tooth survival was 91.6%. Four chippings (two LU, two CS), three fractures (three LU), and two debonding of the restorations (two CS) occurred. Also, two teeth were extracted after 5 years of follow-up (two VE) because of secondary caries and a root fracture. The USPHS ratings were high, except for color match, which was rated the lowest at all time intervals. CONCLUSION: Nanoceramic endocrowns made using a completely digital workflow have an acceptable survival rate after 5 years. However, the complication rate was high.

Effect of Sinus Perforation with Flaplessly Placed Mini Dental Implants for Oral Rehabilitation: A 5-Year Clinical and Radiological Follow-Up.

BACKGROUND: Flaplessly placed one-piece mini dental implants (MDI) are an option to support maxillary overdentures. Evenly distribution of the implants over the atrophic alveolar process implies a risk of accidental sinus perforation in the posterior area which could induce sinus-related pathology. METHODS: Thirty-one patients received 5-6 maxillary MDIs. Schneiderian membrane swelling was assessed with CBCT at the deepest point of the sinus in the mid-sagittal plane prior to surgery (baseline), after 2 and 5 years. Additionally, subjective patient-reported rhinosinusitis complaints, the effect of smoking, and gender differences were investigated. RESULTS: Mean thickness of the Schneiderian membrane was 2.87 mm at baseline, 3.15 mm at 2 years, and 4.30 mm at 5 years in 27 of 31 initially treated patients. MDI perforation was detected in 21/54 sinuses. At 2 years, perforation length does not affect membrane thickness whereas baseline swelling does. In smokers, each perforated mm induced 0.87 mm additional swelling. After 5 years, the effect of baseline swelling becomes smaller whereas perforation length became statistically significant, with 0.53 mm increase for every perforated mm. The effect of smoking lost its significance. No relations between gender, membrane thickness changes, or subjective clinical sinus complaints and MDI perforation were found. CONCLUSION: Accidental MDI sinus perforation induces Schneiderian membrane swelling but does not interfere with clinical sinusal outcome after 5 years.

Accuracy of Guided Implant Surgery Using an Intraoral Scanner and Desktop 3D-Printed Tooth-Supported Guides.

PURPOSE: The increasing popularity of desktop 3D printers makes guided surgery more accessible. The aim of this in vitro study was to evaluate the accuracy of single-tooth guided implant surgery by means of a 3D-printed tooth-supported guide. MATERIALS AND METHODS: Fifteen implants were virtually planned to replace a missing first mandibular molar, using planning software for guided implant surgery (Exoplan, Exocad). A tooth-supported guide was designed and manufactured using a desktop 3D printer (Asiga MAX UV). The implants were placed fully guided in resin casts, and a digital impression was taken to register their position. This scan was compared with the virtual implant position in the planning software, and the internal fit of the guides was evaluated using metrology software. One planning was executed six times for measuring precision. RESULTS: For trueness, the mean angular deviation was 2.63 degrees (SD: 1.69 degrees; range: 0.38 to 5.99 degrees), the mean coronal deviation was 0.52 mm (SD: 0.25; range: 0.09 mm to 1.07 mm), and the mean apical deviation was 0.90 mm (SD: 0.47; range: 0.14 to 1.74 mm). The absolute apical mean deviation in the buccolingual direction (x-axis) was 0.70 mm (SD: 0.42, 0.12 to 1.65 mm; P < .001); in the mesiodistal direction (y-axis), it was 0.34 mm (SD: 0.26; range: 0.01 to 0.80 mm; P = .650); and in the vertical direction (z-axis), it was 0.32 mm (SD: 0.27; range: 0.02 to 1.00 mm; P = .010). The mean internal fit of the guides was 79.5 µm (SD: 19.6 µm; range: 51 to 118 µm). CONCLUSION: Desktop 3D-printed tooth-supported guides demonstrate an acceptable fit and acceptable level of accuracy for single implant placement.

Two-year clinical performance of glass ionomer and resin composite restorations in xerostomic head- and neck-irradiated cancer patients.

The aim of this study was to evaluate the clinical performance of adhesive filling materials in class V cavities in xerostomic head- and neck-irradiated cancer patients, in terms of marginal adaptation, anatomical form and recurrent caries. We selected 35 high-caries-risk, post-radiation, xerostomic adults with ≥3 cervical carious lesions in the same arch. Every patient received a KetacFil (KF), PhotacFil (PF) and Herculite XRV (HX) restoration. Patients were instructed to use a neutral 1% sodium fluoride gel in custom trays, on a daily basis. After 6, 12, 18 and 24 months, the restorations were examined for material loss, marginal integrity and recurrent caries. Fluoride compliance was determined at each recall appointment and recorded as the percentage of recommended use during that interval [compliance of ≤50% = NFUs, >50% = FUs]. Only 30 patients were available for recall at 6 months, with 28 patients at 12 and 18 months, and 27 patients at 24 months. In the NFU group, differences in recurrent caries were found between KF and HX at all observation times (p < 0.05). Differences (p < 0.05) in adaptation and/or anatomical form were found between KF and PF in NFUs after 18 and 24 months. In FUs, significant differences were observed between KF and PF, and KF and HX after 6 and 12 months, between KF and HX, PF and HX after 18 and 24 months. In summary, glass ionomers (especially the conventionally setting formulation) provide clinical caries inhibition but erode easily, while composite resin provides greater structural integrity.

Accuracy of Guided Implant Surgery in the Edentulous Jaw Using Desktop 3D-Printed Mucosal Supported Guides.

PURPOSE: The aim of this in vitro study is to evaluate the accuracy of implant position using mucosal supported surgical guides, produced by a desktop 3D printer. METHODS: Ninety implants (Bone Level Roxolid, 4.1 mm × 10 mm, Straumann, Villerat, Switzerland) were placed in fifteen mandibular casts (Bonemodels, Castellón de la Plana, Spain). A mucosa-supported guide was designed and printed for each of the fifteen casts. After placement of the implants, the location was assessed by scanning the cast and scan bodies with an intra-oral scanner (Primescan®, Dentsply Sirona, York, PA, USA). Two comparisons were performed: one with the mucosa as a reference, and one where only the implants were aligned. Angular, coronal and apical deviations were measured. RESULTS: The mean implant angular deviation for tissue and implant alignment were 3.25° (SD 1.69°) and 2.39° (SD 1.42°) respectively, the coronal deviation 0.82 mm (SD 0.43 mm) and 0.45 mm (SD 0.31 mm) and the apical deviation 0.99 mm (SD 0.45 mm) and 0.71 mm (SD 0.43 mm). All three variables were significantly different between the tissue and implant alignment (p < 0.001). CONCLUSION: Based on the results of this study, we conclude that guided implant surgery using desktop 3D printed mucosa-supported guides has a clinically acceptable level of accuracy. The resilience of the mucosa has a negative effect on the guide stability and increases the deviation in implant position.

Contour Changes Following Immediate Placement of Ultra-Wide Implants in Molar Extraction Sockets without Bone Grafting.

The aim was to evaluate ridge reduction and mucosal recession following immediate placement of ultra-wide implants in molar sockets, without bone grafting. Impressions were taken prior to tooth extraction, 4 months and 1 year after implant placement. The casts were digitized and compared. Mucosal recessions and horizontal ridge reduction were measured. A total of 16 implants were in the maxilla and 11 in the mandible. At the buccal aspect, there was a mean reduction of 0.94 mm after 4 months and 0.89 mm after one year (p = 0.933). At the palatal/lingual aspect, this was 1.09 mm after 4 months and 0.69 mm after 1 year (p = 0.001). After 1 year, a recession of 0.59 mm was measured at the zenith, 1.04 mm at the mesial and 0.98 mm at the distal papilla. The mean midfacial horizontal ridge reduction was 1.23 mm after 4 months and 1.45 mm after 1 year. At the midpalatal/midlingual aspect, the mean horizontal reduction was 1.43 mm after 4 months and 1.16 mm after 1 year. Immediate implant placement without bone grafting in the posterior jaw yields a significant horizontal ridge reduction and minor mucosal recession. Clinicians should anticipate the amount of ridge reduction and consider augmentation at the time of implant placement.

Three-Dimensional Radiographic Outcome of Free-Handed Flaplessly Placed Mini Dental Implants in Edentulous Maxillae after 2-Years Function.

BACKGROUND: Free-handed, flaplessly placed mini dental implants (MDIs) are a valuable, more affordable and minimally invasive treatment to support overdentures in fully edentulous jaws, especially for medically compromised patients. However, critical 3D radiographic evaluation is lacking. This multicenter prospective case series assessed clinical outcome and carried out 3D- cone-beam computerized tomography (CBCT) analysis of free-handed flaplessly placed one-piece maxillary MDIs by an experienced maxillofacial surgeon. METHODS: Thirty-one patients suffering from an ill-fitting maxillary denture relating to compromised bone volume (as confirmed on CBCT), with a dentate mandible, were selected. They received 5-6 MDIs free-hand flaplessly placed and mentally guided with preoperative CBCT. Final connection and attachment activation took place six months later. After two years each implant was individually assessed with CBCT for perforations on eight sites. Implant survival, prosthetic failure, clinical stability and sinus/nasal complaints were registered after three years. RESULTS: 32/185 (17.3%) MDIs failed during the provisional loading with non-activated attachments; 17 replacements in 10 patients were performed. Of the 170 actively loaded 170 MDIs, 82.3% survived and 27/31 prostheses (87%) were fully functional. In total 98/170 MDIs showed no perforation. Based on 1360 CBCT observations, 231 perforations (16.9%) were registered. Of most perforations 37 (25%) were observed at the apical tip and 37 were positioned (21%) into the sinus/nasal cavity, although without clinical complaints. CONCLUSIONS: Given the compromised population, the minimally invasive procedure and the low treatment cost involved, a failure rate of 17% is substantial, however clinically acceptable given the critical bone condition. However, even in experienced surgical hands, freehanded and flapless placement yield a high risk for implant perforation, although this did not necessarily lead to complications.

A prospective study on ultra-wide diameter dental implants for immediate molar replacement.

BACKGROUND: Although wide diameter implants are well documented, little is known about ultra-wide diameter implants (>6 mm). This study evaluates the clinical outcome of ultra-wide diameter implants, placed in molar extraction sockets. MATERIALS AND METHODS: Ultra-wide diameter implants (7-9 mm) were placed immediately after molar extraction in a 1-stage protocol, without raising a flap or using any bone grafts. After 4 months, the implant was loaded with a single screw-retained crown. Bone loss was evaluated using peri-apical radiographs. Plaque and bleeding were recorded. Crown and papilla dimensions were measured and compared with the contra-lateral tooth. RESULTS: Fifty-one patients (36 male and 15 female), mean ages 61 years old, were treated with 26 implants in the maxilla and 25 implants in the mandible. The majority had a thick (#19) or medium (#31) biotype. After a mean-follow-up period of 23 months, the mean bone level was located 1.16 mm apical of the implant-abutment junction (SD 0.42, range 0.00-2.45) while the actual bone remodeling associated with socket healing resulted in a mean coronal movement of the bone level of 0.15 mm. The mean insertion torque was 116 Ncm (SD 53, range 10-250). There were no differences in papilla height (P = .55), crown length (P = .32), zenith (P = .84), and bucco-palatal dimensions (P = .38). There was a significant difference in the mesio-distal dimension (P = .01). Mean probing depth was 2.59 mm at the implant and 2.23 mm at the contra-lateral tooth (P = .001). There was significantly more plaque at the tooth compared to the implant (P = .01), but there was no significant difference in terms of bleeding on probing (P = .08). Patient satisfaction was high with 72.5% of the patients experiencing no problems at all. CONCLUSIONS: Ultra-wide diameter implants have a predictable outcome, demonstrating very little bone loss. Papilla and crown dimensions were comparable to the contra-lateral natural tooth.

Surgical root restoration after external inflammatory root resorption: A case report.

External inflammatory root resorption after a jaw fracture is rare. This report describes a case of extensive external root resorption in the middle third of the root of a mandibular right canine after a mandibular fracture involving the tooth socket. Because of delayed treatment and damage to the root caused by a surgical screw, root canal treatment was performed followed by surgical intervention. The resorptive defect was debrided and part of the root was rebuilt with conventionally setting restorative glass ionomer cement. Postoperative follow-up revealed complete healing.

Longitudinal study on the influence of Nd:YAG laser irradiation on microleakage associated with two filling techniques.

OBJECTIVE: This study investigates the effects of Nd:YAG laser irradiation on apical and coronal seals, when used prior to two root canal filling techniques. BACKGROUND DATA: Limited information exists regarding the effects of morphologic changes to dentin walls following Nd:YAG laser irradiation on the sealing ability of root fillings. METHODS: Two hundred forty teeth were analyzed by observing coronal and apical leakage of Indian ink (DL), and 60 were analyzed for through-and-through leakage using the fluid transport model (FTM). The Nd:YAG laser parameters were 1.5 W, 100 mJ, and 15 Hz (four times for 5 s at 20 s intervals). Each group consisted of a lased and a nonlased subgroup: each subgroup had root fills done by either cold lateral condensation (CLC) or hybrid condensation (HC). Leakage was assessed after 48 h, and then at 1, 6, and 12 months. The DL group was divided into four groups of 15 teeth for each evaluation point. Through-and-through leakage (L in microliters/day) was measured for 48 h under a pressure of 1.2 atm using FTM, and recorded as L = 0 (L1), 0 < L 10 (L3). RESULTS: Apical and coronal dye leakage was observed in all groups. Significant differences (p < 0.05) in apical leakage were found between HC and HC + Nd after 1, 6, and 12 months, and between CLC and CLC + Nd at 6 and 12 months. No significant differences were found between laser-irradiated and non-laser-irradiated groups with FTM. CONCLUSION: Pulsed Nd:YAG laser irradiation following root canal preparation may reduce apical leakage in association with hybrid gutta-percha condensation.

Fraudulent use of digital radiography: methods to detect and protect digital radiographs.

Digital radiography has become an indispensable diagnostic tool in dentistry today. To improve vision and diagnosis, dental x-ray software allows image enhancement (eg, adjusting color, density, sharpness, brightness, or contrast). Exporting digital radiographs to a file format compatible with commercial graphic software increases chances that information can be altered, added, or removed in an unethical manner. Dental radiographs are easily duplicated, stored, or distributed in digital format. It is difficult to guarantee the authenticity of digital images, which is especially important in insurance or juridic cases. Image-enhancement features applied to digital radiographs allow mishandling or potential abuse. This has been illustrated by several recently published studies. A standard authentication procedure for digital radiographs is needed. A number of manipulated radiographic images are presented to show concerns about security, reliability, and the potential for fraud. Antitampering techniques and methods of detecting manipulations in digital medical images are discussed.

Terminal restriction fragment length polymorphism analysis of the microflora in necrotic teeth of patients irradiated in the head and neck region.

This study evaluated the microflora in root canals of necrotic teeth after radiotherapy of the head and neck region. The microbial composition of samples taken from necrotic root canals in patients treated with irradiation of the head and neck (group A, n = 13) and in healthy controls (group B, n = 11) was analyzed by terminal restriction fragment-length polymorphism (T-RFLP) analysis. A total of 50 different terminal restriction fragment lengths (T-RFs) (each representing one or more bacterial species) were detected in the T-RFLP profiles, 44 in group A and 28 in group B. A mean of 13.2 T-RFs per sample were detected in group A and 6.6 T-RFs were present per sample for group B (p < 0.05). Twenty-two different T-RFs (mainly subspecies of Lactobacillus spp., Capnocytophaga spp., and Actinomyces spp.) found in group A were not found in group B. In conclusion, the diversity of root canal microflora increases significantly after head-neck radiotherapy.

[Dental and buccal complications of lip and tongue piercing]. / Complications dentaires et buccales des piercings labiaux et linguaux.

Oral and facial piercing with different kinds of body art are being observed more frequently in medical and dental practices. Principally, piercing is not a new form of body art and is traditional in different geographical areas. In this review, the possible risks and complications are described. Postprocedural complications are oedema, haemorrhage and infection. Other adverse outcomes include mucosal or gingival trauma, chipped or fractured teeth, increased salivary flow, calculus build-up, and interference with speech, mastication and swallowing. Dentists, and oral- and maxillofacial surgeons should be in the position to advise patients with orofocial piercings or those who plan to have this type of body art performed.

[Endodontics and apical periodontitis]. / Endodontie et parodontite apicale.

The aim of this paper is to discuss the relation between root canal treatment and apical periodontitis (AP). AP is caused by micro organisms and is mainly a chronic inflammation. There is some evidence of an effect on the general health in immunocompromised patients. A higher incidence of AP on root filled teeth has been found. A number of preoperative and operative factors influence prevalence of AP on root filled teeth. Rubberdam placement and cleaning and shaping of the root canal during root canal treatment is important to create a clean canal to promote healing or prevent the development of AP. Placement of a good quality root filling and a well sealing coronal restoration are also important for the prevention of reinfection of the root canal. The quality of root fillings differs between clinical and epidemiological studies what is reflected in a lower prevalence of AP in the former.