Efficiency Analysis of Powertrain for Internal Combustion Engine and Hydrogen Fuel Cell Tractor According to Agricultural Operations.

As interest in eco-friendly work vehicles grows, research on the powertrains of eco-friendly tractors has increased, including research on the development of eco-friendly vehicles (tractors) using hydrogen fuel cell power packs and batteries. However, batteries require a long time to charge and have a short operating time due to their low energy efficiency compared with hydrogen fuel cell power packs. Therefore, recent studies have focused on the development of tractors using hydrogen fuel cell power packs; however, there is a lack of research on powertrain performance analysis considering actual working conditions. To evaluate vehicle performance, an actual load measurement during agricultural operation must be conducted. The objective of this study was to conduct an efficiency analysis of powertrains according to their power source using data measured during agricultural operations. A performance evaluation with respect to efficiency was performed through comparison and an analysis with internal combustion engine tractors of the same level. The specifications of the transmission for hydrogen fuel cell and engine tractors were used in this study. The power loss and efficiency of the transmission were calculated using ISO 14179-1 equations, as shown below. Plow tillage and rotary tillage operations were conducted for data measurement. The measurement system consists of four components. The engine data load measurement was calculated using the vehicle's controller area network (CAN) data, the axle load was measured using an axle torque meter and proximity sensors, and fuel consumption was measured using the sensor installed on the fuel line. The calculated capacities, considering the engine's fuel efficiency for plow and rotary tillage operations, were 131.2 and 175.1 kWh, respectively. The capacity of the required power, considering the powertrain's efficiency for hydrogen fuel cell tractors with respect to plow and rotary tillage operations, was calculated using the efficiency of the motor, inverter, and power pack, and 51.3 and 62.9 kWh were the values obtained, respectively. Considering these factors, the engine exhibited an efficiency of about 47.9% compared with the power pack in the case of plow tillage operations, and the engine exhibited an efficiency of about 29.3% in the case of rotary tillage operations. A hydrogen fuel cell tractor is considered suitable for high-efficiency and eco-friendly vehicles because it can operate on eco-friendly power sources while providing the advantages of a motor.

Traction Performance Evaluation of the Electric All-Wheel-Drive Tractor.

This study aims to design, develop, and evaluate the traction performance of an electric all-wheel-drive (AWD) tractor based on the power transmission and electric systems. The power transmission system includes the electric motor, helical gear reducer, planetary gear reducer, and tires. The electric system consists of a battery pack and charging system. An engine-generator and charger are installed to supply electric energy in emergency situations. The load measurement system consists of analog (current) and digital (battery voltage and rotational speed of the electric motor) components using a controller area network (CAN) bus. A traction test of the electric AWD tractor was performed towing a test vehicle. The output torques of the tractor motors during the traction test were calculated using the current and torque curves provided by the motor manufacturer. The agricultural work performance is verified by comparing the torque and rpm (T-N) curve of the motor with the reduction ratio applied. The traction is calculated using torque and specifications of the wheel, and traction performance is evaluated using tractive efficiency (TE) and dynamic ratio (DR). The results suggest a direction for the improvement of the electric drive system in agricultural research by comparison with the conventional tractor through the analysis of the agricultural performance and traction performance of the electric AWD tractor.

Analysis of the Effect of Tillage Depth on the Working Performance of Tractor-Moldboard Plow System under Various Field Environments.

The purpose of this study was to analyze the tillage depth effect on the tractor-moldboard plow systems in various soil environments and tillage depths using a field load measurement system. A field load measurement system can measure the engine load, draft force, travel speed, wheel axle load, and tillage depth in real-time. In addition, measurement tests of soil properties in the soil layer were preceded to analyze the effect of field environments. The presented results show that moldboard plow at the same tillage depth had a wide range of influences on the tractor's working load and performance under various environments. As the draft force due to soil-tool interaction occurred in the range of 5.6-17.7 kN depending on the field environment, the overall mean engine torque and rear axle torque were up to 2.14 times and 1.67 times higher in hard and clayey soil, respectively, than in soft soil environments. In addition, the results showed tractive efficiency of 0.56-0.73 and were analyzed to have a lugging ability of 67.8% with a 44% maximum torque rise. The engine power requirement in hardpan was similar within 3.6-9.6%, but the power demand of the rear axle differed by up to 18.4%.

Evaluation of exhaust emissions of agricultural tractors using portable emissions measurement system in Korean paddy field.

Recently, diesel engine emissions have been designated as a first-class carcinogen by the World Health Organization (WHO). As such, problems with diesel engine emissions continue to increase around the world. This study aimed to analyze the emissions (CO, NOx, PM) of agricultural tractors during farming operations in order to build a reliable national inventory of air pollutant emissions. Emission data were collected using a portable emission measurement system during actual agricultural operation. The load factor (LF) of the engine was calculated using the collected engine information, the emission factor was analyzed using the LF and the measured emission. The LF was significantly different from the current standard value of 0.48, which is used in Korea to calculate exhaust emissions. The deviation ratio of the emission factor was 0.039 ~ 56.59 compared to Tier-4 emission regulation standards. Under many conditions, the calculated emission factor was higher than the emission limit. Thus, this study provides useful information for emission inventory construction through emission calculation under actual conditions and suggests the need to realize the currently applied emission factor.