High diopter spectacle using a flexible Fresnel lens with a combination of grooves.

In this study, the Fresnel lens was investigated as a potential candidate for vision correction in patients with myopia. A few previous studies have suggested this idea; however, Fresnel lenses are limited by their aesthetics and quality. Therefore, we designed a combination of Fresnel lens grooves with a constant height and pitch of 13 µm and 0.1 mm, respectively, to overcome the limitations caused by ultra-precision machining with a tool nose radius of 30 µm. A thin replicated Fresnel lens with a power of -5 diopter was procured and applied directly as spectacles that are unattached to the normal lens. The optical performance and image quality of the Fresnel lens were compared with those of a conventional lens possessing the same power in both near and far vision. These results extend the applicability for the use of Fresnel lenses as vision-correcting ophthalmological lenses and imaging systems.

Integrated, Automated, Fast PCR System for Point-Of-Care Molecular Diagnosis of Bacterial Infection.

We developed an integrated PCR system that performs automated sample preparation and fast polymerase chain reaction (PCR) for application in point-of care (POC) testing. This system is assembled from inexpensive 3D-printing parts, off-the-shelf electronics and motors. Molecular detection requires a series of procedures including sample preparation, amplification, and fluorescence intensity analysis. The system can perform automated DNA sample preparation (extraction, separation and purification) in ≤5 min. The variance of the automated sample preparation was clearly lower than that achieved using manual DNA extraction. Fast thermal ramp cycles were generated by a customized thermocycler designed to automatically transport samples between heating and cooling blocks. Despite the large sample volume (50 µL), rapid two-step PCR amplification completed 40 cycles in ≤13.8 min. Variations in fluorescence intensity were measured by analyzing fluorescence images. As proof of concept of this system, we demonstrated the rapid DNA detection of pathogenic bacteria. We also compared the sensitivity of this system with that of a commercial device during the automated extraction and fast PCR of Salmonella bacteria.

Large area patterning of residue-free metal oxide nanostructures by liquid transfer imprint lithography.

One-dimensional (1D) and three-dimensional (3D) residue-free metal oxide patterns are directly fabricated over large areas using liquid transfer imprint lithography (LTIL) with an ultraviolet-curable metal oxide precursor resist. A 1D line or pillar array of metal oxides nano-patterns without a residual layer is formed by LTIL and annealing processes. A 3D layer-by-layer nanomesh structure is successfully constructed by repeating the LTIL method without a complex etching process. In addition, it is possible to form a hierarchical structure in which zinc oxide nanowires are selectively grown on a desired zinc oxide (ZnO) seed pattern formed by LTIL via a hydrothermal method. Unlike the pattern fabricated by the conventional nanoimprint lithography method, in the case of the pattern formed by LTIL the residues accumulated between the patterns during the patterning procedure can be removed, and thus it is possible to easily form various types of nanostructures.

Formation of Interstitial Hot-Spots Using the Reduced Gap-Size between Plasmonic Microbeads Pattern for Surface-Enhanced Raman Scattering Analysis.

To achieve an effective surface-enhanced Raman scattering (SERS) sensor with periodically distributed "hot spots" on wafer-scale substrates, we propose a hybrid approach combining physical nano-imprint lithography and a chemical deposition method to form a silver microbead array. Nano-imprint lithography (NIL) can lead to mass-production and high throughput, but is not appropriate for generating strong "hot-spots." However, when we apply electrochemical deposition to an NIL substrate and the reaction time was increased to 45 s, periodical "hot-spots" between the microbeads were generated on the substrates. It contributed to increasing the enhancement factor (EF) and lowering the detection limit of the substrates to 4.40 × 106 and 1.0 × 10-11 M, respectively. In addition, this synthetic method exhibited good substrate-to-substrate reproducibility (RSD < 9.4%). Our research suggests a new opportunity for expanding the SERS application.

Hydrothermal Growth of ZnO Nanowires on UV-Nanoimprinted Polymer Structures.

Integration of zinc oxide (ZnO) nanowires on miniaturized polymer structures can broaden its application in multi-functional polymer devices by taking advantages of unique physical properties of ZnO nanowires and recent development of polymer microstructures in analytical systems. In this paper, we demonstrate the hydrothermal growth of ZnO nanowires on polymer microstructures fabricated by UV nanoimprinting lithography (NIL) using a polyurethane acrylate (PUA). Since PUA is a siloxane-urethane-acrylate compound containing the alpha-hydroxyl ketone, UV-cured PUA include carboxyl groups, which inhibit and suppress the nucleation and growth of ZnO nanowires on polymer structures. The presence of carboxyl groups in UV-cured PUA was substantiated by Fourier transform infrared spectroscopy (FTIR), and a Ag thin film was deposited on the nanoimprinted polymer structures to limit their inhibitive influence on the growth of ZnO nanowires. Furthermore, the naturally oxidized Ag layer (Ag2O) reduced crystalline lattice mismatches at the interface between ZnO-Ag during the seed annealing process. The ZnO nanowires grown on the Ag-deposited PUA microstructures were found to have comparable morphological characteristics with ZnO nanowires grown on a Si wafer.

A Sensitive Potentiometric Sensor for Isothermal Amplification-Coupled Detection of Nucleic Acids.

A disposable potentiometric sensor was newly developed for the amplification-coupled detection of nucleic acids. The hydrogen-ion is generally released during isothermal amplification of nucleic acids. The surface potential on the oxide-functionalized electrode of the extended gate was directly measured using full electrical circuits with the commercial metal-oxide semiconductor field-effect transistors (MOSFETs) and ring oscillator components, which resulted in cost-effective, portable and scalable real-time nucleic acid analysis. The current-starved ring oscillator changes surface potential to its frequency depending on the square of the variation in pH with a high signal-to-noise ratio during isothermal amplification. The device achieves a conversion rate of 20.5 kHz/mV and a detection resolution of 200 µV for the surface potential. It is demonstrated that the sensor successfully monitors in real-time isothermal amplification of the extracted nucleic acids from Salmonella pathogenic bacteria. The in situ variations in the frequency of the pH-sensitive sensor were compared with the results of both a conventional optical device and pH-meter during isothermal amplification.

Challenges of Positive Airway Pressure Treatment for Patients With Obstructive Sleep Apnea at a Veterans Medical Center.

OBJECTIVE: Positive airway pressure (PAP) compliance is important in treating obstructive sleep apnea. Previous studies have suggested that patients with economic burdens, discomfort using machines, and insufficient education have difficulty tolerating PAP machines. This study explored the factors affecting short-term adherence to PAP in a veterans medical center. METHODS: The medical records of patients who underwent polysomnography at the Veterans Health Service Medical Center, Seoul, Republic of Korea, between July 2018 and January 2021 were reviewed retrospectively. Patients with an apnea-hypopnea index (AHI) ≥15 were included (n=579). PAP adherence was defined as continuous use for ≥21 days for ≥4 hours daily for 30 consecutive days for 90 days from the date of PAP prescription. RESULTS: The PAP-adherent group (n=265, age 66.16±11.28 years) was younger and had more years of education, higher body mass indices, and lower scores in the Insomnia Severity Index and Beck Depression Inventory-II (BDI-II) than those of the PAP-nonadherent group (n=314, age 68.93±10.91 years). Patients who tolerated PAP had a higher AHI, longer duration of oxygen desaturation (less than 90%), and less dream enactment behavior (DEB) than that in those who did not. After adjusting for age, years of education, BDI-II, duration of oxygen desaturation, and presence of DEB, there were more patients with National Health Insurance (NHI) in the PAP-adherent group than in the PAP-nonadherent group (p<0.001). CONCLUSION: We showed that patients with NHI recorded significantly higher adherence compared to that in patients without NHI, among other factors.

Surface Functionalization of 3D-Printed Scaffolds with Seed-Assisted Hydrothermally Grown ZnO Nanoarrays for Bone Tissue Engineering.

Bioactive metal-based nanostructures, particularly zinc oxide (ZnO), are promising materials for bone tissue engineering. However, integrating them into 3D-printed polymers using traditional blending methods reduces the cell performance. Alternative surface deposition techniques often require extreme conditions that are unsuitable for polymers. To address these issues, we propose a metal-assisted hydrothermal synthesis method to modify 3D printed polycaprolactone (PCL) scaffolds with ZnO nanoparticles (NPs), facilitating the growth of ZnO nanoarrays (NAs) at a low-temperature (55 °C). Physicochemical characterizations revealed that the ZnO NPs form both physical and chemical bonds with the PCL surface; chemical bonding occurs between the carboxylate groups of PCL and Zn(OH)2 during seed deposition and hydrothermal synthesis. The ZnO NPs and NAs grown for a longer time (18 h) on the surface of PCL scaffolds exhibit significant proliferation and early differentiation of osteoblast-like cells. The proposed method is suitable for the surface modification of thermally degradable polymers, opening up new possibilities for the deposition of diverse metals.

Complex object wave direct extraction method in off-axis digital holography.

Off-axis digital holography generally uses a 2D-FFT based spatial filtering method to extract the complex object wave from an off-axis hologram. In this paper, we describe a novel single exposure complex object wave extraction method which can provide a faster solution than the FFT based spatial filtering approach while maintaining the reconstructed phase image quality. And also, we show that the proposed direct filtering scheme can provide more robust filtering capability to the off-axis spatial carrier frequency variation than the spatial filtering method.

Calibration of a snapshot phase-resolved polarization-sensitive spectral reflectometer.

This Letter describes a universal calibration theory by which conventional interferometry can be extended to vibration robust snapshot polarization-sensitive spectral reflectometry without any complicated optical components or active devices. Experiments for verifying the proposed calibration theory have been conducted by using a Michelson-interferometer-based normal incidence spectroellipsometric system, and also some key system design considerations for object 3D pose tolerant measurement capability have been drawn. The proposed solution enables us to extract the spectroscopic ellipsometric parameter Δ(k) of an anisotropic object within 10 ms with high accuracy.

Improvement of the efficiency of Si solar cells using nano-microscale combination patterns.

Solar cells have a high reported energy conversion efficiency level according to various techniques. The energy conversion efficiency, however, is limited by the reflection of the light at the packaging glass surface. For this reason, some research groups are focused on nano/micro scale patterns. Nano/micro scale patterns can increase the energy conversion efficiency by means of light absorption. In this paper, we used three types of master stamps 300 nm pitch of a moth-eye pattern, a micro lens, and a hole pattern with a 200 nm diameter. These patterns were fabricated using UV-nanoimprint lithography on a cover glass which served as a protective layer of a Si solar cell. In additional, the transmittance and conversion efficiency of single-crystal Si solar cell were measured. Consequently, the conversion efficiency of a Si solar cell was found to increase from 16.69% to 18.16%.

A new mold structure to replicate patterns over 1 microm in depth for substrate conformal imprint lithography.

This paper shows an improved mold replication process that uses polyurethane acrylate (PUA) and polyethylene terephthalate (PET) for the fabrication of an ultraviolet (UV) imprinting mold used in substrate conformal imprint lithography (SCIL). With the conventional replication process, which uses hard polydimethylsiloxane (h-PDMS) as a pattern layer, it is difficult to detach the mold from a silicon master for metal oxide semiconductor field effect transistor (MOSFET) that has patterns with over 1-micron depth. However, the method proposed in this paper allows us to easily replicate patterns that have more than 1-micron depth. The key idea of this method is to use PET film as a bonding layer to attach the PUA layer to the polydimethylsiloxane (PDMS) cushion layer to overcome the weak the adhesion force between the PUA and PDMS layer. We demonstrate how to make the modified replica mold and present imprinting results obtained using this replica mold in the SCIL process.

Rapid Electrohydrodynamic-Driven Pattern Replication over a Large Area via Ultrahigh Voltage Pulses.

Despite the prospects of electrohydrodynamic instability patterning (EHIP), poor process parameter controllability is a significant challenge in uniform large-scale nanopatterning. Herein, we introduce a EHIP process using an ultrahigh electric field (>108 V/m) to effectively accelerate the pattern growth evolution. Owing to the strong dependence on a temporal parameter (1/τm) of the field strength, our method not only reduces the completion time of pattern growth but also overcomes critical parametric restrictions on the pattern replication, thereby enhancing the replicated pattern quality in three dimensions. The pattern can be uniformly replicated over the entire film surface even without a perfectly uniform air gap, which has been severely difficult in the conventional method. To further demonstrate how straightforward yet versatile our approach is, we applied our EHIP approach to successfully replicate the densely packed nanostructures of cicada wings.

Real-time and label-free biosensing using moiré pattern generated by bioresponsive hydrogel.

Bioresponsive hydrogels are smart materials that respond to various external stimuli and exhibit great potential as biosensors owing to their capability of real-time and label-free detection. Here, we propose a sensing platform based on bioresponsive hydrogels, employing the concept of moiré patterns. Two sets of line patterns with different pitch sizes are prepared; a hydrogel grating whose pitch size changes according to external stimuli and a reference grating with constant pitch size. The volume changes of the hydrogel caused by external stimuli changes the pitch size of the hydrogel grating, and subsequently, the pitch sizes of the moiré patterns (moiré signal), whose values can be obtained in a real-time and label-free manner through customized moiré microscopy and signal processing. After confirming that the pH-induced swelling of hydrogel could be monitored using moiré patterns, we performed moiré pattern-based detection of specific proteins using protein-responsive hydrogel that underwent shrinking via interaction with target proteins. Brain-derived neurotrophic factor and platelet-derived growth factor were selected as the model proteins, and our proposed system successfully detected both proteins at nanomolar levels. In both cases, the pitch size change of hydrogel grating was monitored much more sensitively using moiré patterns than through direct measurements. The changes in the moiré signals caused by target proteins were detected in ex-vivo environments using a custom-made intraocular lens incorporating the hydrogel grating, demonstrating the capability of the proposed system to detect various markers in intraocular aqueous humor, when implanted in the eye.

Conductive Thread-Based Immunosensor for Pandemic Influenza A (H1N1) Virus Detection.

Infectious agents such as viruses pose significant threats to human health, being transmitted via direct contact as well as airborne transmission without direct contact, thus requiring rapid detection to prevent the spread of infectious diseases. In this study, we developed a conductive thread-based immunosensor (CT-IS), a biosensor to easily detect the presence of airborne viruses. CT-IS utilizes an antibody that specifically recognizes the HA protein of the pandemic influenza A (pH1N1) virus, which is incorporated into the conductive thread. The antigen-antibody interaction results in increased strain on the conductive thread in the presence of the pH1N1 virus, resulting in increased electrical resistance of the CT-IS. We evaluated the performance of this sensor using the HA protein and the pH1N1 virus, in addition to samples from patients infected with the pH1N1 virus. We observed a significant change in resistance in the pH1N1-infected patient samples (positive: n = 11, negative: n = 9), whereas negligible change was observed in the control samples (patients not infected with the pH1N1 virus; negative). Hence, the CT-IS is a lightweight fiber-type sensor that can be used as a wearable biosensor by combining it with textiles, to detect the pH1N1 virus in a person's vicinity.

Pattern uniformity in large-area ultraviolet nano-imprinting by a cylindrically inflated flexible mold under low pressure.

This paper shows a novel nano-imprint method with a polydimethylsiloxane (PDMS) replica mold that was bonded on a cylindrically inflated polycarbonate (PC) film via a low air pressure. The PDMS mold, which was deformed in terms of its cylindrical shape, made a line contact with a substrate from the center region and the contact region, then expanded gradually to the outside of the substrate when the contact force increased. This contact procedure squeezed the resin that was dropped on the substrate from the center to the outside, which prevented the trapping of air bubbles while the cavities were filled with the patterns on the PDMS mold. The main characteristic of the proposed process was that the nano-imprint can be realized under a low pressure, compared to conventional processes. We will show the system that was implemented under the proposed process concept and the patterns that were transferred in an ultraviolet curable resin under pressure conditions of less than 5 kPa.

Fabrication of Nanostructures on a Large-Area Substrate with a Minimized Stitch Error Using the Step-and-Repeat Nanoimprint Process.

Nanoimprint lithography (NIL) is suitable for achieving high uniformity and mass production. However, in conventional NIL, a stamp suitable for the substrate size is required to increase the substrate size. To address this issue, we fabricated nanostructures on a large-area substrate using step-and-repeat NIL after making a small stamp. A stamp was produced using glass, and a nano-pillar pattern with a diameter of 600 nm, an interval of 400 nm, and a height of 270 nm was used during the experiment. The area of the pattern on the stamp was 10 mm × 10 mm, and the step-and-repeat process was performed 25 times to transfer the nanostructures to a 4-inch substrate. In addition, stitch gaps were created between the patterns, which could decrease the performance upon future application. To minimize this stitch gap, a high-precision glass scale was attached to the stamp feeder to precisely control the position and to minimize the step difference. Moreover, an experiment was conducted to minimize the stitch gap by adjusting the movement interval of the stamp, and the stitch spacing was minimized by moving the stamp position by 9.97 mm. This approach will facilitate the manufacturing of large-area substrates and other structures in the future.

Microfluidic device for one-step detection of breast cancer-derived exosomal mRNA in blood using signal-amplifiable 3D nanostructure.

Metastasis attributed to approximately 90% of cancer-related deaths; hence, the detection of metastatic tumor-derived components in the blood assists in determining cancer recurrence and patient survival. Microfluidic-based sensors facilitate analysis of small fluid volumes and represent an accurate, rapid, and user-friendly method of field diagnoses. In this study, we have developed a microfluidic chip-based exosomal mRNA sensor (exoNA-sensing chip) for the one-step detection of exosomal ERBB2 in the blood by integrating a microfluidic chip and 3D-nanostructured hydrogels. The exoNA-sensing chip is a vacuum-driven power-free microfluidic chip that can accurately control the flow of trace fluids (<100 µL). The sensing part of the exoNA-sensing chip includes 3D-nanostructured hydrogels capable of detecting ERBB2 and a reference gene by amplifying a fluorescent signal via an enzyme-free catalytic hairpin assembly reaction at room temperature. This hydrogel offers a detection limit of 58.3 fM with good selectivity for target sequences. The performance of the exoNA-sensing chip was evaluated by testing in vitro and in vivo samples and was proven to be effective for cancer diagnosis and liquid biopsies.

Improvement of the non-uniform resist patterns in the thermal nanoimprint process using Si stamp with nanoscale rod patterns.

To acquire the uniform resist patterns in thermal nanoimprint lithography (TH-NIL), the major considerations include control of the resist, stamp and substrate resist under the imprint condition. Examples of these factors are management of the imprinting pressure, imprinting temperature and releasing temperature. Non-uniform patterns of thermal imprinted resist appear after TH-NIL according to the pattern size, substrate size and resist thickness. Particularly, the hole-shaped patterns with a diameter of 100 nm and a height of 100 nm on a 4 inch Si wafer after TH-NIL were deformed under tension to the maximum strain 70%. The experimental results showed that uniform nano-patterns can be acquired by minimizing the thermal mismatch while nanoimprinting through using a pair of Si stamp and Si substrate, thinning the resist thickness and separating the stamp at a relatively high temperature.

Parametric scheme for rapid nanopattern replication via electrohydrodynamic instability.

Electrohydrodynamic (EHD) instability patterning exhibits substantial potential for application as a next-generation lithographic technique; nevertheless, its development continues to be hindered by the lack of process parameter controllability, especially when replicating sub-microscale pattern features. In this paper, a new parametric guide is introduced. It features an expanded range of valid parameters by increasing the pattern growth velocity, thereby facilitating reproducible EHD-driven patterning for perfect nanopattern replication. Compared with conventional EHD-driven patterning, the rapid patterning approach not only shortens the patterning time but also exhibits enhanced scalability for replicating small and geometrically diverse features. Numerical analyses and simulations are performed to elucidate the interplay between the pattern growth velocity, fidelity of the replicated features, and boundary between the domains of suitable and unsuitable parametric conditions in EHD-driven patterning. The developed rapid route facilitates nanopattern replication using EHD instability with a wide range of suitable parameters and further opens up many opportunities for device applications using tailor-made nanostructures in an effective and straightforward manner.