Comparison of Primary Laser Spectroscopy and Mass Spectrometry Methods for Measuring Mass Concentration of Gaseous Elemental Mercury.

We present a direct comparison between two independent methods for the measurement of gaseous elemental mercury (GEM) mass concentration: isotope dilution cold-vapor inductively coupled plasma mass spectrometry (ID-CV-ICP-MS) and laser absorption spectroscopy (LAS). The former technique combined with passive sorbent tube sampling is currently the primary method at NIST for mercury gas standards traceability to the International System of Units (SI). This traceability is achieved via measurements on a mercury-containing reference material. The latter technique has been recently developed at NIST and involves real-time measurements of light attenuation caused by GEM, with SI traceability based in part on the known spontaneous emission lifetime of the probed 6 1S0-6 3P1 intercombination transition of elemental mercury (Hg0). Using a steady-flow Hg0-in-air generator to produce samples measured by both methods, we use LAS to measure the sample gas and in parallel we collect the Hg0 on sorbent tubes to be subsequently analyzed using ID-CV-ICP-MS. Over the examined mass concentration range (41 µg/m3 to 287 µg/m3 Hg0 in air), the relative disagreement between the two approaches ranged from (1.0 to 1.8)%. The relative combined standard uncertainty on average is 0.4% and 0.9%, for the LAS and MS methods, respectively. Our comparison studies help validate the accuracy of the ID-CV-ICP-MS primary method as well as establish the LAS technique as an attractive alternative primary method for SI-traceable measurements of GEM.

Development of a pregnancy-specific reference material for thyroid biomarkers, vitamin D, and nutritional trace elements in serum.

OBJECTIVES: Matrix differences among serum samples from non-pregnant and pregnant patients could bias measurements. Standard Reference Material 1949, Frozen Human Prenatal Serum, was developed to provide a quality assurance material for the measurement of hormones and nutritional elements throughout pregnancy. METHODS: Serum from non-pregnant women and women in each trimester were bottled into four levels based on pregnancy status and trimester. Liquid chromatography tandem mass spectrometry (LC-MS/MS) methods were developed and applied to the measurement of thyroid hormones, vitamin D metabolites, and vitamin D-binding protein (VDBP). Copper, selenium, and zinc measurements were conducted by inductively coupled plasma dynamic reaction cell MS. Thyroid stimulating hormone (TSH), thyroglobulin (Tg), and thyroglobulin antibody concentrations were analyzed using immunoassays and LC-MS/MS (Tg only). RESULTS: Certified values for thyroxine and triiodothyronine, reference values for vitamin D metabolites, VDBP, selenium, copper, and zinc, and information values for reverse triiodothyronine, TSH, Tg, and Tg antibodies were assigned. Significant differences in serum concentrations were evident for all analytes across the four levels (p≤0.003). TSH measurements were significantly different (p<0.0001) among research-only immunoassays. Tg concentrations were elevated in research-only immunoassays vs. Federal Drug Administration-approved automated immunoassay and LC-MS/MS. Presence of Tg antibodies increased differences between automated immunoassay and LC-MS/MS. CONCLUSIONS: The analyte concentrations' changes consistent with the literature and the demonstration of matrix interferences in immunoassay Tg measurements indicate the functionality of this material by providing a relevant matrix-matched reference material for the different stages of pregnancy.

Examining maternal and environmental transfer of mercury into American alligator eggs.

American alligators are exposed to mercury (Hg) throughout their natural range and may maternally transfer Hg into their eggs. Wildlife species are highly sensitive to Hg toxicity during embryonic development and neonatal life, and information on Hg transfer into eggs is critical when attempting to understand the effects of Hg exposure on developing oviparous organisms. To examine Hg transfer in alligators, the objectives of the present study were to 1) determine Hg concentrations in yolk (embryonic and neonatal food source) from wild alligator eggs collected from three locations - Yawkey Wildlife Center SC (YWC), Lake Apopka FL (LA), and Lake Woodruff FL (LW); 2) examine the relationship between THg concentrations in wild alligator nest material and egg yolk at Merritt Island National Wildlife Refuge, FL; 3) examine the Hg concentrations in wild maternal female alligators (blood) and the THg in corresponding egg yolks and embryos across three nesting seasons at a single location (YWC), and evaluate the relationship between nesting female THg concentrations (blood) and their estimated age and number of nesting years (YWC); and 4) assess the transfer of biologically-relevant Hg concentrations (based on Hg measured in maternal female blood) into embryos using an egg-dosing experiment. Mean total Hg (THg) concentrations observed at each site were 26.3 ng/g ± 11.0 ng/g (YWC), 8.8 ng/g ± 5.1 ng/g (LA), and 22.6 ng/g ± 6.3 ng/g (LW). No relationship was observed between THg in alligator nest material and corresponding yolk samples, nor between THg in maternal alligator blood and estimated age and number of nesting years of these animals. However, significant positive relationships were observed between THg in blood of nesting female alligators and THg in their corresponding egg yolk. We observed that 12.8% of the maternal blood THg is found in the corresponding egg yolk, and a highly significant correlation was observed between the two sample types (r = 0.66; p < 0.0001). The egg dosing experiment revealed that Hg did not transfer through the eggshell at developmental stage 19. Overall, this study provides new information regarding Hg transfer in American alligators which can improve biomonitoring efforts and may inform ecotoxicological investigations and population management programs in areas of high Hg contamination.

Development of a kelp powder (Thallus laminariae) Standard Reference Material.

A Standard Reference Material (SRM) of seaweed, SRM 3232 Kelp Powder (Thallus laminariae) has been developed to support food and dietary supplement measurements in compliance with the Food Safety Modernization Act (FSMA) and the Dietary Supplement Health and Education Act of 1994 (DSHEA). The material was characterized for nutritional minerals, arsenic species, isomers of vitamin K1, proximates, and toxic elements. Kelp is a rich source of vitamins and minerals, and it is an excellent source of dietary iodine. Kelp also contains a large amount of arsenic, which is toxic as inorganic species but much less so as organic species. To capture the dietary profile of kelp, certified values were issued for As, Ca, Cd, Cr, Cu, Fe, Hg, I, K, Mg, Mn, Mo, Na, Pb, and Zn. Reference values for proximates were assigned. For the first time, a certified value for iodine, reference values for isomers of vitamin K1, and reference values for arsenic species including arsenosugars were assigned in a seaweed. SRM 3232 fills a gap in Certified Reference Materials (CRMs) needed for quality assurance and method validation in the compositional measurements of kelp and similar seaweeds used as food and as dietary supplements. Graphical Absract Arsenic species and isomers of vitamin K1 were determined in the development of SRM 3232 Kelp Powder (Thallus laminariae).

Development of two fine particulate matter standard reference materials (<4 µm and <10 µm) for the determination of organic and inorganic constituents.

Two new Standard Reference Materials (SRMs), SRM 2786 Fine Particulate Matter (<4 µm) and SRM 2787 Fine Particulate Matter (<10 µm) have been developed in support of the US Environmental Protection Agency's National Ambient Air Quality Standards for particulate matter (PM). These materials have been characterized for the mass fractions of selected polycyclic aromatic hydrocarbons (PAHs), nitrated PAHs, brominated diphenyl ether (BDE) congeners, hexabromocyclododecane (HBCD) isomers, sugars, polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners, and inorganic constituents, as well as particle-size characteristics. These materials are the first Certified Reference Materials available to support measurements of both organic and inorganic constituents in fine PM. In addition, values for PAHs are available for RM 8785 Air Particulate Matter on Filter Media. As such, these SRMs will be useful as quality control samples for ensuring compatibility of results among PM monitoring studies and will fill a void to assess the accuracy of analytical methods used in these studies. Graphical Abstract Removal of PM from filter for the preparation of SRM 2786 Fine Particulate Matter.

Urinary iodine and stable isotope analysis to examine habitat influences on thyroid hormones among coastal dwelling American alligators.

The American alligator, generally a freshwater species, is known to forage in marine environments despite the lack of a salt secreting gland found in other crocodylids. Estuarine and marine foraging could lead to increased dietary uptake of iodine, a nutrient necessary for the production of thyroid hormones. To explore the influence of dietary iodine on thyroid hormone health of coastal dwelling alligators, we described the seasonal plasma thyroxine and triiodothyronine concentrations measured by radioimmunoassay and urinary iodine (UI) concentrations measured by inductively coupled plasma mass spectrometry. We also analyzed long-term dietary patterns through stable isotope analysis of scute tissue. Snout-to-vent length (SVL) was a significant factor among UI and stable isotope analyses. Large adult males greater than 135cm SVL had the highest UI concentrations but did not display seasonality of thyroid hormones. Alligators under 135 SVL exhibited seasonality in thyroid hormones and a positive relationship between UI and triiodothyronine concentrations. Isotopic signatures provided supporting evidence that large males predominantly feed on marine/estuarine prey whereas females showed reliance on freshwater/terrestrial prey supplemented by marine/estuarine prey. UI measurement provided immediate information that correlated to thyroid hormone concentrations whereas stable isotope analysis described long-term dietary patterns. Both techniques demonstrate that adult alligators in coastal environments are utilizing estuarine/marine habitats, which could alter thyroid hormone physiology.

Standard addition method for laser ablation ICPMS using a spinning platform.

A method has been developed for the fast and easy determination of Pb, Sr, Ba, Ni, Cu, and Zn, which are of geological and environmental interest, in solid samples by laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS) using a spinning sample platform. The platform, containing a sample and a standard, is spun during the ablation, allowing the quasi-simultaneous ablation of both materials. The aerosols resulting from the ablation of sample and standard were mixed in the ablation cell allowing quantification of analytes by standard additions. The proportion of standard versus sample of the mixing can be increased by performing the ablation further from the axis of rotation. The ablated masses have been determined using a new strategy based on isotope dilution analysis. This spinning laser ablation method has been applied to the Allende meteorite and four powdered standard reference materials (SRMs) fused in lithium borate glasses: two sediments as well as a soil and a rock material. SRM 612 (Trace Elements in Glass) was also analyzed despite having a matrix slightly different from the glass standard obtained by lithium borate fusion. The deviation from the certified values was found to be less than 15% for most of the mass fractions for all the elements and samples studied, with an average precision of 10%. These results demonstrate the validity of the proposed method for the direct and fast analysis of solid samples of different matrixes by standard additions, using a single standard sample.

Development of a Standard Reference Material for metabolomics research.

The National Institute of Standards and Technology (NIST), in collaboration with the National Institutes of Health (NIH), has developed a Standard Reference Material (SRM) to support technology development in metabolomics research. SRM 1950 Metabolites in Human Plasma is intended to have metabolite concentrations that are representative of those found in adult human plasma. The plasma used in the preparation of SRM 1950 was collected from both male and female donors, and donor ethnicity targets were selected based upon the ethnic makeup of the U.S. population. Metabolomics research is diverse in terms of both instrumentation and scientific goals. This SRM was designed to apply broadly to the field, not toward specific applications. Therefore, concentrations of approximately 100 analytes, including amino acids, fatty acids, trace elements, vitamins, hormones, selenoproteins, clinical markers, and perfluorinated compounds (PFCs), were determined. Value assignment measurements were performed by NIST and the Centers for Disease Control and Prevention (CDC). SRM 1950 is the first reference material developed specifically for metabolomics research.

Putting a spin on LA-ICP-MS analysis combined to isotope dilution.

The determination of Zn, Sr, Ba, and Pb in solid samples has been achieved by laser ablation inductively coupled plasma isotope dilution mass spectrometry using a spinning platform. The fast rotation of a sample and an isotopically enriched spike placed close together on a sample holder allowed performing the isotope dilution directly inside the ablation cell. The proportion of spike versus sample of the aerosol mixture obtained has been determined online by isotope dilution in order to correct for differences in ablation rate although both materials were placed on the axis of rotation of the motor. Homogeneous, time-stable, and reusable samples were prepared by lithium borate fusion. A unique isotopically enriched spike glass was used to analyze four Standard Reference Materials of different matrix (after a simple polishing): two sediments Standard Reference Material (SRM) 1944 and SRM 2702 and two soils SRM 2586 and SRM 2711a. The proposed method yielded mass fractions with a deviation from the certified value usually lower than 12% and a precision of less than 9% RSD (except for Zn in SRM 2586 and 2711a). Although direct spiking of the solid before fusion could presumably provide better isotopic mixing, the presented methodology allows the reuse of the spike glass (thus, decreasing drastically the cost of the analysis) and is relatively faster because the spike does not need to be weighted, added, and evaporated each time. These results demonstrate the potential of this newly developed method for fast analysis of solid samples using isotope dilution at a low cost.

Fast and accurate determination of K, Ca, and Mg in human serum by sector field ICP-MS.

Electrolytes in serum are important biomarkers for skeletal and cellular health. The levels of electrolytes are monitored by measuring the Ca, Mg, K, and Na in blood serum. Many reference methods have been developed for the determination of Ca, Mg, and K in clinical measurements; however, isotope dilution thermal ionization mass spectrometry (ID-TIMS) has traditionally been the primary reference method serving as an anchor for traceability and accuracy to these secondary reference methods. The sample matrix must be separated before ID-TIMS measurements, which is a slow and tedious process that hindered the adoption of the technique in routine clinical measurements. We have developed a fast and accurate method for the determination of Ca, Mg, and K in serum by taking advantage of the higher mass resolution capability of the modern sector field inductively coupled plasma mass spectrometry (SF-ICP-MS). Each serum sample was spiked with a mixture containing enriched (44)Ca, (26)Mg, and (41)K, and the (42)Ca(+):(44)Ca(+), (24)Mg(+):(26)Mg(+), and (39)K(+):(41)K(+) ratios were measured. The Ca and Mg ratios were measured in medium resolution mode (m/Δm ≈ 4 500), and the K ratio in high resolution mode (m/Δm ≈ 10 000). Residual (40)Ar(1)H(+) interference was still observed but the deleterious effects of the interference were minimized by measuring the sample at K > 100 ng g(-1). The interferences of Sr(++) at the two Ca isotopes were less than 0.25 % of the analyte signal, and they were corrected with the (88)Sr(+) intensity by using the Sr(++):Sr(+) ratio. The sample preparation involved only simple dilutions, and the measurement using this sample preparation approach is known as dilution-and-shoot (DNS). The DNS approach was validated with samples prepared via the traditional acid digestion approach followed by ID-SF-ICP-MS measurement. DNS and digested samples of SRM 956c were measured with ID-SF-ICP-MS for quality assurance, and the results (mean ± expanded uncertainty in mg dL(-1) unit) for Ca (DNS = 10.14 ± 0.13, digested = 10.11 ± 0.10), Mg (DNS = 2.093 ± 0.008, digested = 2.098 ± 0.007), and K (DNS = 15.48 ± 0.11, digested = 15.50 ± 0.28) were in good agreement with the certified values (Ca = 10.17 ± 0.06, Mg = 2.084 ± 0.023, K = 15.55 ± 0.13). Major sources of uncertainty are sample measurement, spike calibration, and instrument factor including mass discrimination of the spectrometer and the detector deadtime.

Certification of elements in and use of standard reference material 3280 multivitamin/multielement tablets.

Standard Reference Material 3280 Multivitamin/ Multielement Tablets was issued by the National Institute of Standards and Technology in 2009, and has certified and reference mass fraction values for 13 vitamins, 26 elements, and two carotenoids. Elements were measured using two or more analytical methods at NIST with additional data contributed by collaborating laboratories. This reference material is expected to serve a dual purpose: to provide quality assurance in support of a database of dietary supplement products and to provide a means for analysts, dietary supplement manufacturers, and researchers to assess the appropriateness and validity of their analytical methods and the accuracy of their results.

Summary of an NIH workshop to identify research needs to improve the monitoring of iodine status in the United States and to inform the DRI.

The Office of Dietary Supplements (ODS) at the NIH sponsored a workshop on May 12-13, 2011, to bring together representatives from various NIH institutes and centers as a first step in developing an NIH iodine research initiative. The workshop also provided an opportunity to identify research needs that would inform the dietary reference intakes for iodine, which were last revised in 2001. Iodine is required throughout the life cycle, but pregnant women and infants are the populations most at risk of deficiency, because iodine is required for normal brain development and growth. The CDC monitors iodine status of the population on a regular basis, but the status of the most vulnerable populations remains uncertain. The NIH funds very little investigator-initiated research relevant to iodine and human nutrition, but the ODS has worked for several years with a number of other U.S. government agencies to develop many of the resources needed to conduct iodine research of high quality (e.g., validated analytical methods and reference materials for multiple types of samples). Iodine experts, scientists from several U.S. government agencies, and NIH representatives met for 2 d to identify iodine research needs appropriate to the NIH mission.

Fast and accurate procedure for the determination of Cr(VI) in solid samples by isotope dilution mass spectrometry.

We present here a new environmental measurement method for the rapid extraction and accurate quantification of Cr(VI) in solid samples. The quantitative extraction of Cr(VI) is achieved in 10 minutes by means of focused microwave assisted extraction using 50 mmol/L Ethylendiamintetraacetic acid (EDTA) at pH 10 as extractant. In addition, it enables the separation of Cr species by anion exchange chromatography using a mobile phase which is a 1:10 dilution of the extracting solution. Thus, neutralization or acidification steps which are prone to cause interconversion of Cr species are not needed. Another benefit of using EDTA is that it allows to measure Cr(III)-EDTA complex and Cr(VI) simultaneously in an alkaline extraction solution. The application of a 10 minutes focused microwave assisted extraction (5 min at 90 °C plus 5 min at 110 °C) has been shown to quantitatively extract all forms of hexavalent chromium from the standard reference materials (SRM) candidate NIST 2700 and NIST 2701. A double spike isotope dilution mass spectrometry (IDMS) procedure was employed to study chromium interconversion reactions. It was observed that the formation of a Cr(III)-EDTA complex avoided Cr(III) oxidation for these two reference materials. Thus, the use of a double spiking strategy for quantification is not required and a single spike IDMS procedure using isotopically enriched Cr(VI) provided accurate results.

Mercury stable isotopes in seabird eggs reflect a gradient from terrestrial geogenic to oceanic mercury reservoirs.

Elevated mercury concentrations ([Hg]) were found in Alaskan murre (Uria spp.) eggs from the coastal embayment of Norton Sound relative to insular colonies in the northern Bering Sea-Bering Strait region. Stable isotopes of Hg, carbon, and nitrogen were measured in the eggs to investigate the source of this enrichment. Lower δ(13)C values in Norton Sound eggs (-23.3‰ to -20.0‰) relative to eggs from more oceanic colonies (-20.9‰ to -18.7‰) indicated that a significant terrestrial carbon source was associated with the elevated [Hg] in Norton Sound, implicating the Yukon River and smaller Seward Peninsula watersheds as the likely Hg source. The increasing [Hg] gradient extending inshore was accompanied by strong decreasing gradients of δ(202)Hg and Δ(199)Hg in eggs, indicating lower degrees of mass-dependent (MDF) and mass-independent Hg fractionation (MIF) (respectively) in the Norton Sound food web. Negative or zero MDF and MIF signatures are typical of geological Hg sources, which suggests murres in Norton Sound integrated Hg from a more recent geological origin that has experienced a relatively limited extent of aquatic fractionation relative to more oceanic colonies. The association of low δ(202)Hg and Δ(199)Hg with elevated [Hg] and terrestrial δ(13)C values suggested that Hg stable isotopes in murre eggs effectively differentiated terrestrial/geogenic Hg sources from oceanic reservoirs.

Development of Kudzu (Pueraria Montana var. lobata) Reference Materials for the Determination of Isoflavones and Toxic Elements.

BACKGROUND: In collaboration with the Office of Dietary Supplements at the National Institutes of Health, the National Institute of Standards and Technology issued a suite of botanical matrix reference materials (RMs) and Standard Reference Material® (SRM) for determination of isoflavones and toxic elements in kudzu dietary supplement ingredients. OBJECTIVE: RM 8650 Pueraria montana var. lobata (Kudzu) Rhizome, SRM 3268 Pueraria montana var. lobata (Kudzu) Extract, and RM 8652 Kudzu-Containing Solid Oral Dosage Form were issued with values assigned for isoflavones (puerarin, daidzin, and daidzein), toxic elements (arsenic, cadmium, and lead), and selenium. METHODS: Isoflavone values were assigned using liquid chromatography with UV absorbance or mass spectrometry detection. Element values were assigned using inductively coupled plasma mass spectrometry and results from an interlaboratory comparison exercise. RESULTS: Mass fractions for puerarin were 32.2 ± 3.2 mg/g, 128 ± 13 mg/g, and 68.2 ± 6.9 mg/g in RM 8650, SRM 3268, and RM 8652, respectively. Arsenic increases from 156 ± 14 ng/g to 849 ± 83 ng/g and cadmium decreases from 348 ± 14 ng/g to 82.1 ± 4.9 ng/g from rhizome to extract. CONCLUSION: The kudzu RM/SRM suite complements previously issued soy-related SRMs with values assigned for isoflavones, which have been studied for their potential health benefits, and expands the analytical resource by providing values for puerarin, an isoflavone not found in soy. HIGHLIGHTS: The three new kudzurmaterials are for use in the determination of isoflavones, toxic elements, and selenium. For the isoflavones, these new kudzu materials provide higher levels of daidzin and daidzein than existing soy-related SRMs, and they provide a value for an isoflavone not in existing SRMs (puerarin). Toxic elements in RM 8650 and SRM 3268 provide new botanical matrixes for use by dietary supplement manufacturers for the verification of the safety of their raw materials.

Evaluation of hexavalent chromium extraction method EPA method 3060A for soils using XANES spectroscopy.

Hexavalent chromium (Cr(VI)) occurrence in soils is generally determined using an extraction step to transfer it to the liquid phase where it is more easily detected and quantified. In this work, the performance of the most common extraction procedure (EPA Method 3060A) using NaOH-Na(2)CO(3) solutions is evaluated using X-ray absorption near edge structure spectroscopy (XANES), which enables the quantification of Cr(VI) directly in the solid state. Results obtained with both methods were compared for three solid samples with different matrices: a soil containing chromite ore processing residue (COPR), a loamy soil, and a paint sludge. Results showed that Cr(VI) contents determined by the two methods differ significantly, and that the EPA Method 3060A procedure underestimated the Cr(VI) content in all studied samples. The underestimation is particularly pronounced for COPR. Low extraction yield for EPA Method 3060A was found to be the main reason. The Cr(VI) present in COPR was found to be more concentrated in magnetic phases. This work provides new XANES analyses of SRM 2701 and its extraction residues for the purpose of benchmarking EPA 3060A performance.

Measuring silver nanoparticle dissolution in complex biological and environmental matrices using UV-visible absorbance.

Distinguishing the toxic effects of nanoparticles (NPs) themselves from the well-studied toxic effects of their ions is a critical but challenging measurement for nanotoxicity studies and regulation. This measurement is especially difficult for silver NPs (AgNPs) because in many relevant biological and environmental solutions, dissolved silver forms AgCl NPs or microparticles. Simulations predict that solid AgCl particles form at silver concentrations greater than 0.18 and 0.58 µg/mL in cell culture media and moderately hard reconstituted water (MHRW), respectively. The AgCl NPs are usually not easily separable from AgNPs. Therefore, common existing total silver techniques applied to measure AgNP dissolution, such as inductively coupled plasma mass spectrometry (ICP-MS) or atomic absorption, cannot accurately measure the amount of silver remaining in AgNP form, as they cannot distinguish Ag oxidation states. In this work, we introduce a simple localized surface plasmon resonance (LSPR) UV-visible absorbance measurement as a technique to measure the amount of silver remaining in AgNP form for AgNPs with constant agglomeration states. Unlike other existing methods, this absorbance method can be used to measure the amount of silver remaining in AgNP form even in biological and environmental solutions containing chloride because AgCl NPs do not have an associated LSPR absorbance. In addition, no separation step is required to measure the dissolution of the AgNPs. After using ICP-MS to show that the area under the absorbance curve is an accurate measure of silver in AgNP state for unagglomerating AgNPs in non-chloride-containing media, the absorbance is used to measure dissolution rates of AgNPs with different polymer coatings in biological and environmental solutions. We find that the dissolution rate decreases at high AgNP concentrations, 5 kDa polyethylene glycol thiol coatings increase the dissolution rate, and the rate is much higher in cell culture media than in MHRW.

Chromatographic methods for the quantification of free and chelated gadolinium species in MRI contrast agent formulations.

Speciation measurements of gadolinium in liposomal MRI contrast agents (CAs) are complicated by the presence of emulsifiers, surfactants, and therapeutic agents in the formulations. The present paper describes two robust, hyphenated chromatography methods for the separation and quantification of gadolinium in nanoemulsion-based CA formulations. Three potential species of gadolinium, free gadolinium ion, gadolinium chelated by diethylenetriamine pentaacetic acid, and gadolinium chelated by 1,2-dimyristoyl-sn-glycero-3-phosphoethanolamine-N-diethylenetriaminepentaacetic acid, were present in the CA formulations. The species were separated by reversed-phase chromatography (reversed phase high-performance liquid chromatography, RP-HPLC) or by high-pressure size-exclusion chromatography (HPSEC). For RP-HPLC, fluorescence detection and post-column online isotope dilution inductively coupled plasma mass spectrometry (ID-ICP-MS) were used to measure the amount of gadolinium in each species. Online ID-ICP-MS and species-specific isotope dilution (SID)-ICP-MS were used in combination with the HPSEC column. The results indicated that some inter-species conversions and degradation had occurred within the samples and that SID-ICP-MS should be used to provide the most reliable measurements of total and speciated gadolinium. However, fluorescence and online ID-ICP-MS might usefully be applied as qualitative, rapid screening procedures for the presence of free gadolinium ions.

Assessing a method and reference material for quantification of vitamin D binding protein during pregnancy.

Vitamin D plays a vital role in successful pregnancy outcomes for both the mother and fetus. Vitamin D is bound to vitamin D binding protein (VDBP) in blood and is carried to the liver, kidneys and other target tissues. Accurate measurements of the clinically measured metabolite of vitamin D, 25-hydroxyvitamin D [25(OH)D], depend on complete removal from the binding protein. It has been found that VDBP concentrations increase in maternal serum during pregnancy, obfuscating the accuracy of 25(OH)D concentration measurements in pregnant women. Additionally, measurements of VDBP concentrations during pregnancy have been performed using immunoassays, which suffer from variations due to differences in antibody epitopes, making clinical comparisons difficult. Quantification of VDBP is also of interest because changes in VDBP expression levels may indicate negative outcomes during pregnancy, such as preterm delivery and restricted fetal growth. To address the need for accurate measurement of VDBP during pregnancy, a method using liquid chromatography-isotope dilution mass spectrometry (LC-IDMS) was developed to quantify VDBP using isotopically labeled peptides as internal standards. This method was used to quantify VDBP in Standard Reference Material® (SRM) 1949 Frozen Human Prenatal Serum, which was prepared from separate serum pools of women who were not pregnant and women during each trimester of pregnancy. VDBP concentrations were found to be lowest in the serum pool from non-pregnant women and increased in each trimester. These data had good repeatability and were found to be suitable for reference value assignment of VDBP in SRM 1949.

Demonstrating the comparability of certified reference materials.

Certified reference materials (CRMs) enable the meaningful comparison of measurement results over time and place. When CRMs are used to calibrate or verify the performance of a measurement system, results produced by that system can be related through the CRM to well-defined, stable, and globally accessible reference(s). Properly done, this directly establishes the metrological traceability of the results. However, achieving the meaningful comparison of results from measurement systems calibrated and/or verified with different CRMs requires that the different materials truly deliver the same measurand, that is, are "the same" within stated uncertainty except for differences in the level of the analyte of interest. We here detail experimental and data analysis techniques for establishing and demonstrating the comparability of materials. We focus on (1) establishing a uniform interpretation of the common forms of CRM uncertainty statements, (2) estimating consistent measurement system response uncertainties from sometimes inconsistent experimental designs, (3) using "errors-in-variables" analysis methods to evaluate comparability studies and novel graphical tools for communicating results of the evaluation to reviewing authorities and potential CRM customers, and (4) augmenting established comparability studies with new materials using measurements provided by the certifying institution. These experimental and data analytic tools were developed in support of the Joint Committee for Traceability in Laboratory Medicine's efforts to enhance the reliability of clinical laboratory measurements and are illustrated with potassium and cholesterol measurands of clinical relevance; however, these tools can be applied to any group of materials that deliver the same nominal measurand with stated value and uncertainty.